SN74LS245N - 8-Bit 3-State Bus Transceiver | Texas Instruments
N.º da peça: SN74LS245N ✓ AtivoSN74LS245N Visão geral
A bus transceiver is an interface IC that connects two digital logic sections while providing directional control and output isolation. The SN74LS245N is specifically suited to systems where processors, memory, peripheral devices, or I/O modules share parallel data lines. Unlike a dedicated one-way buffer, it supports bidirectional transfer by changing the direction of all eight channels together. Its 3-state outputs allow several devices to share a common bus when their output-enable signals are controlled so that only one device actively drives the line at a time.
The principal functional features are eight non-inverting data paths, two bus ports labeled A and B, a common direction control input, a common output enable, and 3-state output behavior. The verified distributor description identifies the part as a non-inverting, one-element, eight-bit-per-element transceiver with a 3-state output and a 20-pin PDIP package. According to the Texas Instruments SN74LS245 datasheet, the control-function arrangement reduces external timing requirements, which is valuable when interfacing asynchronous systems with limited control over source and destination timing.
The SN74LS245N uses tristate outputs rather than open-collector outputs. This distinction is important because a three-state output can actively drive a logic-high or logic-low level while disabled, whereas an open-collector implementation requires a passive pull-up and does not provide a driven high state. The 20-pin PDIP construction favors through-hole assembly, repair, prototyping, and legacy computer or peripheral-interface boards where a socketed or readily replaceable logic package is useful.
Typical uses include bidirectional data buffers, computer peripheral interfaces, asynchronous parallel-bus isolation, instrument and control systems, and educational digital-logic platforms. In a processor interface, the transceiver can place a peripheral bus into a high-impedance state during periods when the processor or another bus master must take control. The common direction and enable controls simplify this arrangement because eight lines change state together rather than requiring individual control signals.
When designing around the SN74LS245N, verify signal direction, output-enable polarity, bus ownership, and setup and hold timing before connecting two independently clocked domains. Disable the outputs before changing direction or transferring control between bus masters. Decoupling requirements, absolute maximum ratings, propagation delay, output-current limits, and environmental limits should be taken directly from the manufacturer datasheet. This page also organizes functional alternatives, pin-level implementation guidance, and parameter comparisons for engineering selection.
Alternativas drop-in para SN74LS245N — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com SN74LS245N (mesmo formato e footprint) — diferindo em Data Direction, Output State, Package.
SN74LS245DW
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
SN74LS245N
✅ Drop-InConsulte o preço
Ver ficha técnica →SN74LS245N
✅ Drop-InConsulte o preço
Ver ficha técnica →SN74LS245N
✅ Drop-InConsulte o preço
Ver ficha técnica →SN74ACT245N
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SN74LS245N Classificações máximas e características elétricas
| Função | Octal non-inverting 3-state bus transceiver |
| Number of Data Channels | 8 channels |
| Bus Width | 8 bits |
| Data Direction | Bidirectional A-to-B or B-to-A |
| Output State | 3-state |
| Logic Polarity | Non-inverting |
| Tensão de alimentação | 5.25 V maximum |
| Encapsulamento | 20-pin PDIP |
| Tipo de montagem | Through-hole |
Configuração de pinos do SN74LS245N
| Pino 1 | 1A — A-side data input or output for channel 1 |
| Pino 2 | 2A — A-side data input or output for channel 2 |
| Pino 3 | 3A — A-side data input or output for channel 3 |
| Pino 4 | 4A — A-side data input or output for channel 4 |
| Pino 5 | GND — Ground reference |
| Pino 6 | DIR — Direction-control input |
| Pino 7 | OE — Output-enable input with active-low control |
| Pino 8 | 8B — B-side data input or output for channel 8 |
| Pino 9 | 7B — B-side data input or output for channel 7 |
| Pino 10 | 6B — B-side data input or output for channel 6 |
| Pino 11 | 5B — B-side data input or output for channel 5 |
| Pino 12 | 4B — B-side data input or output for channel 4 |
| Pino 13 | 3B — B-side data input or output for channel 3 |
| Pino 14 | 2B — B-side data input or output for channel 2 |
| Pino 15 | 1B — B-side data input or output for channel 1 |
| Pino 16 | VCC — Positive supply voltage |
| Pino 17 | 8A — A-side data input or output for channel 8 |
| Pino 18 | 7A — A-side data input or output for channel 7 |
| Pino 19 | 6A — A-side data input or output for channel 6 |
| Pino 20 | 5A — A-side data input or output for channel 5 |
Aplicações típicas
SN74LS245N é adequado para 6 aplicaçãos: Bidirectional Processor Bus Interface, Peripheral Bus Isolation, Industrial Control Data Backplane, Educational Digital Logic Systems, Instrument and Test-System Interface, Legacy Computer Expansion Bus.
Bidirectional Processor Bus Interface
The SN74LS245N fits a legacy 8-bit processor bus when the peripheral side must exchange data with the system bus without driving the bus continuously. Place the transceiver between the two parallel buses, use DIR to establish the active direction, and assert or deassert OE to match bus ownership. Its eight common channels reduce control complexity compared with eight individual buffers. The principal engineering consideration is avoiding contention: disable the outputs before changing direction or allowing another master to take control. Because this is an asynchronous TTL bus device, timing margins must also accommodate propagation delay and the timing of the connected logic.
Recomendado
Peripheral Bus Isolation
The SN74LS245N provides a controlled isolation point between a peripheral bus and a host bus in legacy computer and embedded-control equipment. Its 3-state outputs allow the peripheral side to be disconnected electrically when the host bus is active, while DIR determines which side can drive during a transfer. This arrangement reduces the number of discrete buffers required for an eight-line interface and gives the system a common mechanism for granting bus access. The designer should define ownership logic so OE is deasserted whenever two transceivers could otherwise drive the same node, and should account for enable and direction timing at the system level.
Recomendado
Industrial Control Data Backplane
The SN74LS245N can connect two sections of a parallel industrial control backplane when the system uses 5 V TTL signaling and requires the ability to release the bus. The eight A-side and eight B-side connections permit a controller module and an I/O module to exchange command or status data over a common physical bus. DIR provides a simple direction change, while OE isolates the transceiver when another controller is active. The implementation must include deliberate dead time between OE deassertion, DIR changes, and the next enable because those transitions determine when the outputs may safely begin driving.
Recomendado
Educational Digital Logic Systems
The SN74LS245N is useful in educational systems that demonstrate bidirectional buses, contention, tri-state outputs, and bus arbitration. Its 20-pin PDIP package is straightforward to install on a solderless board or through-hole trainer, while the DIR and OE inputs make operating states easy to observe with LEDs and logic instruments. A lab exercise can show that the direction control selects A-to-B or B-to-A transfer and that the common output enable places all eight channels in a high-impedance state. This makes the device especially effective for demonstrating why only one driver may control a shared bus at a time.
Recomendado
Instrument and Test-System Interface
The SN74LS245N can bridge a legacy 5 V instrument bus and a secondary parallel data section when both sides require a controlled, high-impedance inactive state. Its common DIR input simplifies command-versus-response sequencing, while OE lets the instrument bus relinquish control between transactions. This is useful in systems where a controller, fixture, or measurement module shares an 8-bit line. Designers should verify receiver and driver timing margins at the actual bus capacitance and loading, because the transceiver's electrical limits and propagation timing determine how much margin remains in a multi-device backplane.
Recomendado
Legacy Computer Expansion Bus
The SN74LS245N is suited to a legacy computer expansion interface where an adapter board needs bidirectional eight-bit communication with a central bus. The transceiver provides a controlled path between the adapter data pins and the bus connector while allowing the adapter to remain electrically passive during another device's transaction. Its through-hole PDIP package also supports repairable, socketed assemblies commonly encountered in vintage computer hardware. Before installation, compare the socket pinout and signal direction carefully because legacy computers may use inversion, latching, or registered buffers that cannot be replaced directly by this transceiver.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para SN74LS245N — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | SN74LS245DW | SN74LS245N | SN74LS245N | SN74LS245N | SN74ACT245N |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | ON Semiconductor | NXP Semiconductors | Motorola | Texas Instruments |
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Function | Octal non-inverting bus transceiver | Octal non-inverting bus transceiver | Octal non-inverting bus transceiver | Octal non-inverting bus transceiver | Octal non-inverting bus transceiver | 8-bit bus transceiver |
| Number of Data Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Output Architecture | 3-state | 3-state | 3-state | 3-state | 3-state | 3-state |
| Maximum Supply Voltage | 5.25 V | 5.25 V | 5.25 V | 5.25 V | 5.25 V | 5.25 V |
Principais diferenciais
- Common control for all eight channels (vs SN74LS75N)
- Bidirectional operation with three-state outputs (vs SN74LS373N)
- Drop-in 20-pin PDIP sourcing options (vs SN74ACT245N)
- Avoids open-collector substitution errors (vs SN74LS645N)
Notas de projeto
Never change DIR while the outputs remain enabled and another device may already be driving the shared bus. First deassert OE so that all eight outputs enter the high-impedance state, wait for the relevant timing interval, and then change direction before enabling the new driver. This sequence prevents overlap between the A-side and B-side drivers.
Place the supply bypass capacitor close to pin 16 and provide a short, low-impedance connection to the ground plane. The bypass network should suppress switching noise on the common supply rail while keeping transient current paths away from sensitive signal traces. Confirm capacitor voltage rating, ESR requirements, and recommended placement against the manufacturer datasheet.
Route the eight A-side and eight B-side data lines as a parallel bus with consistent geometry and terminated points where appropriate. Keep DIR and OE traces away from high-current switching nodes to reduce false transition detection. If the transceiver sits at the end of a long bus, verify signal integrity, capacitance, and propagation-delay margin at the actual loading rather than relying only on nominal logic timing.
Account for the combined effect of transceiver propagation delay, remote-device timing, bus capacitance, and any pull-up or pull-down components. The three-state output architecture removes contention only while OE is inactive; it does not resolve timing overlap between two enabled devices. Establish the bus ownership protocol and minimum dead time before connecting the transceiver to legacy asynchronous equipment.
Informações de conformidade
The manufacturer materials describe the device as a 74LS logic IC but do not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements for this ordering code.