SN74LS92NS - Divide-By-Twelve 4-Bit Counter | Texas Instruments | Logic
N.º da peça: SN74LS92NS ✓ AtivoSN74LS92NS Visão geral
A counter is a sequential logic circuit that stores and advances a binary count on each applied clock edge. A ripple counter chains several flip-flops so that the carry output of one stage clocks the next, which makes the device inexpensive and simple to cascade but also makes the accumulated propagation delay grow with the number of stages. The 74LS92 family is the classic divide-by-six and divide-by-twelve member of the 74LS counter line that also contains the 74LS90 (decade) and 74LS93 (divide-by-eight) parts.
Key features include negative-edge triggered counting, separate clock inputs for the divide-by-two section and the binary section, active-low master reset inputs that clear the count chain, and a standard TTL output stage with symmetrical totem-pole drive. Because the SN74LS92NS is a legacy 74LS part rather than a CMOS part, its supply tolerance matches the classic 5 V rail: 4.75 V minimum to 5.25 V maximum, with a typical quiescent current in the low milliamp range.
Internally, the monolithic chip contains four master-slave flip-flops plus gating logic. The master-slave arrangement means the output of a stage changes only after the clock goes low, so the design is free of race conditions when the clock is driven from a debounced switch or a slow ripple network. The divide-by-two section can be cascaded externally with the binary section, giving a divide-by-twelve chain from a single clock source, and the cleared outputs of each stage are often used as qualified enables for downstream gates.
Typical uses include frequency division and pulse-train generation, decade and modulus-12 event counters, ring-timing and sequencer stages in industrial control panels, batch and cycle counting in test equipment, and timing references in legacy TTL or microprocessor subsystems that still run from a 5 V rail.
When designing with this part, tie all unused clock and master reset inputs to defined logic levels rather than leaving them floating, and place a 0.1 uF bypass capacitor close to the supply pin to keep switching current out of the analog-sensitive ground return. Ripple counters also require an acknowledgement that the summed propagation delay of the chained flip-flops appears as a clock-skew interval at the final output, so the maximum input toggle frequency should be checked against the worst-case delay chain.
This page assembles the manufacturer datasheet details, ordering information, equivalent cross-references and practical design notes in one place, adding engineering context that a bare distributor listing does not provide.
Alternativas drop-in para SN74LS92NS — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com SN74LS92NS (mesmo formato e footprint) — diferindo em Counter Type, Logic Family, Package.
SN74LS92D
✅ Drop-InConsulte o preço
Ver ficha técnica →SN74LS92DE4
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SN74LS92NSR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SN74LS92DR
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
SN74LS92D
✅ Drop-InConsulte o preço
Ver ficha técnica →SN74LS92D
✅ Drop-InConsulte o preço
Ver ficha técnica →SN74LS92NS Classificações máximas e características elétricas
| Função | Divide-by-twelve counter (74LS92) |
| Counter Type | 4-bit ripple-type counter, two sections (divide-by-two plus three-stage binary) |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Logic Family | LS (low-power Schottky TTL) |
| Counting Mode | Asynchronous ripple, up count, negative-edge triggered |
| Count Modulus | Divide-by-12 (divide-by-two section cascaded with divide-by-six binary section) |
| Number of Count Outputs | 3 binary outputs (Q0, Q1, Q2) plus divide-by-two section output |
| Master Reset | Active-low clear inputs for both counter sections |
| Encapsulamento | SOIC-14 (NS suffix) |
| Número de pinos | 14 |
| Tipo de montagem | Surface mount |
Configuração de pinos do SN74LS92NS
| Pino 1 | CP1 — Clock input for divide-by-two section, negative-edge triggered |
| Pino 2 | CP0 — Clock input for binary counter section, negative-edge triggered |
| Pino 3 | CLR0 — Active-low master reset for divide-by-two section |
| Pino 4 | CLR1 — Active-low master reset for binary counter section |
| Pino 5 | Q0 — Binary counter output, least significant bit |
| Pino 6 | Q1 — Binary counter output |
| Pino 7 | Q2 — Binary counter output, most significant bit of binary section |
| Pino 8 | GND — Ground reference |
| Pino 9 | Q3 — Cascade / binary section output |
| Pino 10 | C0 — Cascade input for binary counter section |
| Pino 11 | C1 — Cascade input for binary counter section |
| Pino 12 | C2 — Cascade input for binary counter section |
| Pino 13 | C3 — Cascade input for binary counter section |
| Pino 14 | VCC — Positive supply, 4.75 V to 5.25 V |
Aplicações típicas
SN74LS92NS é adequado para 6 aplicaçãos: Frequency Divider and Pulse Generation, Modulus-12 Batch and Cycle Counting, Timing Reference and Sequencer Stage, Test and Measurement Pulse Counting, Automotive and Heavy Equipment Relay Sequencing, Educational and Retro Digital Logic Platforms.
Frequency Divider and Pulse Generation
The SN74LS92NS suits clock division and pulse-train generation in 5 V TTL logic because its divide-by-two section and divide-by-six binary section cascade to give a stable twelve-count ratio. The master-slave flip-flop arrangement means each output changes only after the clock returns low, so a divided clock fed back into a downstream gate produces clean, race-free pulses. A 0.1 uF bypass capacitor close to pin 8 keeps the Schottky TTL switching current out of the logic return path, and the accumulated ripple delay across the chained stages must be included in the maximum input toggle frequency budget for the design.
Recomendado
Modulus-12 Batch and Cycle Counting
In batch counting and cyclic machine sequencing, a modulus-12 count is a natural fit for twelve-station indexers, dispensing cycles and timed process steps. The SN74LS92NS counts on the negative clock edge, so a switch-debounced or contact-driven clock source works directly, and the active-low master reset inputs allow the count to be cleared in step with the machine cycle. Because the device is a ripple counter, the count outputs change sequentially rather than simultaneously, which must be considered if the reset is deasserted too close to a clock edge.
Recomendado
Timing Reference and Sequencer Stage
Legacy microprocessor and TTL control panels often need a repeatable timing reference derived from a slow oscillator. The SN74LS92NS provides three binary outputs from a single clock, and each stage can be gated by the preceding output to form a ripple divider for longer timing chains. Its low-power Schottky TTL input levels match the surrounding 74LS gates without level translation, and the 14-pin SOIC footprint allows the counter to be placed next to the logic it drives. Keep the master reset inputs tied to a defined level rather than floating, so unused sections stay in a known state.
Recomendado
Test and Measurement Pulse Counting
Legacy test equipment and fixture controllers use counters to accumulate events and derive measurement windows. The SN74LS92NS suits fixture logic that still runs on a 5 V TTL rail, because the divide-by-twelve modulus matches many twelve-channel scan or fixture patterns and the negative-edge triggering accepts the collector-coupled event pulses common in that hardware. The counter's clear inputs should be driven from the same reset domain as the fixture's measurement start signal, and the sequential output changes of a ripple counter should be accounted for when the fixture samples the count near a clock edge.
Recomendado
Automotive and Heavy Equipment Relay Sequencing
In legacy relay and solenoid sequencing panels, a modulus-12 counter can drive twelve discrete steps of an equipment cycle. The SN74LS92NS operates from the standard 4.75 V to 5.25 V window that matches the 5 V regulation used in such panels, and the master-slave structure avoids output race conditions when the clock comes from a slow mechanical cam switch. Because the device is a bipolar TTL part rather than an automotive-qualified component, the operating temperature range and any vibration-related requirements must be checked against the manufacturer datasheet before it is used in a harsh environment.
Recomendado
Educational and Retro Digital Logic Platforms
The SN74LS92NS remains a practical choice for breadboard and laboratory teaching platforms built around classic TTL, because the 14-pin SOIC package is easy to socket and the divide-by-two plus divide-by-six section arrangement makes the internal count cycle visible on a logic analyzer. It also serves as a reference design for vintage computer repair, where matching the original Schottky TTL family keeps voltage levels and drive capability consistent with the surrounding 74LS logic. As a ripple counter, the observed output skew between stages is itself a useful teaching point about cumulative propagation delay in cascaded flip-flops.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para SN74LS92NS — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | SN74LS92D | SN74LS92DE4 | SN74LS92NSR | SN74LS92DR | SN74LS92D | 74LS92D |
|---|---|---|---|---|---|---|---|
| Package | SOIC-14 (NS) | SOIC-14 - identical | SOIC-14 - identical | SOIC-14 - identical | SOIC-14 - identical | SOIC-14 - identical (onsemi) | SOIC-14 - identical (Nexperia) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | Nexperia |
| Count Function | Divide-by-twelve counter | Divide-by-twelve counter | Divide-by-twelve counter | Divide-by-twelve counter | Divide-by-twelve counter | Divide-by-twelve counter | Divide-by-twelve counter |
| Logic Family | LS Schottky TTL | LS Schottky TTL | LS Schottky TTL | LS Schottky TTL | LS Schottky TTL | LS Schottky TTL | LS TTL |
| Number of Pins | 14 | 14 | 14 | 14 | 14 | 14 | 14 |
Principais diferenciais
- Exact divide-by-twelve function in a 14-pin SOIC footprint (vs SN74LS90DR)
- Multi-source availability within the same SOIC-14 land pattern (vs SN74LS92D (onsemi))
- Lead-free option available on the same die and footprint (vs SN74LS92D)
- Schottky TTL drive compatible with legacy 74LS logic (vs 74HC4040)
Notas de projeto
Never leave the unused clock inputs (CP0/CP1) or the master reset inputs floating. A floating TTL input sits in the undefined region between the 0.8 V and 2.0 V thresholds, so the counter can advance spontaneously and the clear inputs will not reliably hold the count at zero. Tie every unused input to the supply or ground rail through the same logic level the surrounding 74LS gates use, and keep the clear inputs asserted while the clock is in an unknown state during power-up.
Remember that a ripple counter's outputs change one stage at a time, so the final output transition lags the clock by the sum of all stage propagation delays. When the counter output feeds a decoder, a latch, or another asynchronous section, that skew window can be sampled incorrectly if the design assumes simultaneous output updates. Either sample on the opposite clock phase, insert a latch or flip-flop for synchronisation, or verify the worst-case cumulative delay against the datasheet timing values before fixing the maximum input toggle frequency of the design.
Place the supply bypass capacitor, typically 0.1 uF, directly between pin 14 and pin 8, with the ground connection to the plane as short as possible. The 74LS92 draws pulsed current on each clock edge as the internal flip-flops switch, and long supply traces between the IC and the decoupling capacitor create an inductive voltage step that shows up as a false clock edge on the ripple chain. Route the clock line away from the reset and output lines to keep switching transients from coupling into the count chain.
This is a bipolar Schottky TTL part, so the supply rail must sit inside 4.75 V to 5.25 V. The classic 5 V rail tolerance in older equipment is often wider than that window because it was designed for the original 74LS family, and a rail sitting at 5.5 V or dipping to 4.5 V during brownout can cause the counter to miscount. Where the supply comes from a switching regulator, allow margin so the ripple trough stays above the 4.75 V minimum, and check the regulator's startup overshoot against the 5.25 V maximum.
Informações de conformidade
The published ordering information for the NS suffix does not state RoHS, REACH or halogen-free status, and the family is offered with a DE4 suffix that denotes the lead-free finish, so the specific ordering code must be confirmed before a lead-free assembly. The device is a legacy bipolar TTL counter and carries no AEC-Q100 automotive qualification.