SN75175D - Quad RS-485 Receiver, 10 Mbps | Texas Instruments
N.º da peça: SN75175D ⚠ Última compraSN75175D Visão geral
A differential line receiver belongs to the interface IC hierarchy: it converts small voltage differences between two conductors into a digital logic signal. This conversion allows balanced signaling to reject common-mode noise, reduce ground-reference errors, and improve robustness in industrial environments. The SN75175 family is specifically intended for balanced multipoint data transmission rather than single-ended logic.
Each receiver converts its differential input pair to a logic output. The common enable control places the four outputs into a high-impedance state when required, allowing multiple receivers to share a bus without active-output contention. Three-state operation is particularly useful in bus architectures where several nodes may drive a shared line during different operating intervals. The 50 mV hysteresis helps prevent output chatter around the decision threshold.
The SN75175D supports a maximum signaling rate of 10 Mbps and uses a single 5 V supply. According to the manufacturer datasheet, the device is designed around EIA-485 and EIA-422A/23A balanced-interface requirements and CCITT recommendations. It contains no transmitters, so each channel is a receiver-only path; an external line driver is required when the design also needs to transmit.
Typical uses include industrial RS-485 equipment, data acquisition systems, instrumentation links, computer peripherals, and multipoint communication networks. Because the device supports four channels, one package can serve several independent differential inputs or four nodes on a multidrop bus when the enable function is managed correctly.
PCB design should preserve the differential signal path and provide a continuous return reference. Route each differential pair with matched geometry and avoid adding test pads or long branches that disturb impedance. Decouple the 5 V supply close to the device, and verify that the bus topology, termination, protection, and common-mode range match the cable and environmental conditions.
This page combines manufacturer specifications, compatible substitute references, interface-selection guidance, package details, and practical implementation notes. It helps engineers determine whether the SN75175D fits a legacy RS-485 or RS-422 design and how to validate a replacement before production release.
Alternativas drop-in para SN75175D — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com SN75175D (mesmo formato e footprint) — diferindo em Package, Mounting Type, Maximum Data Rate, Number of Receivers.
SN75175N
✅ Drop-InConsulte o preço
Ver ficha técnica →SN75175DE4
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SN75175DR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SN75175DG4
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SN65175D
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →SN75175D Especificações
| Receiver Type | Quad differential line receiver |
| Number of Receivers | 4 |
| Supported Protocols | RS-422, RS-423, RS-485 |
| Maximum Data Rate | 10 Mbps |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Faixa de temperatura de operação | 0°C to 70°C |
| Receiver Hysteresis | 50 mV |
| Output State Control | Three-state outputs |
| Duplex Support | Receiver-only; no integrated transmitter |
| Encapsulamento | 16-pin SOIC (D) |
| Tipo de montagem | Surface mount |
| Shipping Package | Tube |
Configuração de pinos do SN75175D
| Pino 1 | 1A — Channel 1 non-inverting differential input |
| Pino 2 | 1Y — Channel 1 logic output |
| Pino 3 | 2A — Channel 2 non-inverting differential input |
| Pino 4 | 2Y — Channel 2 logic output |
| Pino 5 | GND — Ground connection |
| Pino 6 | 3Y — Channel 3 logic output |
| Pino 7 | 3A — Channel 3 non-inverting differential input |
| Pino 8 | 4Y — Channel 4 logic output |
| Pino 9 | 4A — Channel 4 non-inverting differential input |
| Pino 10 | VCC — Positive supply connection |
| Pino 11 | EN — Common output-enable input |
| Pino 12 | NC — Not connected (per datasheet) |
| Pino 13 | NC — Not connected (per datasheet) |
| Pino 14 | 2B — Channel 2 inverting differential input |
| Pino 15 | 1B — Channel 1 inverting differential input |
| Pino 16 | 4B — Channel 4 inverting differential input |
Aplicações típicas
SN75175D é adequado para 6 aplicaçãos: Industrial RS-485 Data Acquisition, RS-422 Point-to-Point Links, Multipoint Communication Network, Computer Peripherals and Legacy Equipment, Test and Measurement Instrumentation, Process-Control and Sensor Gateways.
Industrial RS-485 Data Acquisition
The SN75175D is appropriate for receiving four balanced RS-485 signals in industrial data-acquisition equipment because it supports rates up to 10 Mbps with 50 mV hysteresis and three-state outputs. Place one receiver channel on each protected differential pair and manage the common enable so unused outputs enter a high-impedance state. The 4.75 V to 5.25 V supply range supports conventional 5 V interface logic, while the 0°C to 70°C rating suits controlled indoor equipment. External surge protection, chassis grounding, and cable-side isolation should be evaluated because the receiver IC alone does not provide those protections.
Recomendado
RS-422 Point-to-Point Links
The SN75175D can serve as the receiving half of a multi-channel RS-422 interface, converting balanced differential inputs into CMOS-compatible logic signals. Its four channels allow a compact receiver arrangement when a system carries several independent point-to-point links. At rates up to 10 Mbps, cable length, connector geometry, source termination, and receiver input characteristics must be evaluated together. The three-state outputs also permit bus sharing when the host can disable the receiver cleanly. Confirm output enable polarity and logic thresholds in the circuit design because those details control whether the device drops into the existing interface correctly.
Recomendado
Multipoint Communication Network
A multidrop RS-485 network benefits from the SN75175D's four differential receiver channels and three-state output capability. Each receiver can monitor a different node while the enable function keeps outputs inactive when the bus is not assigned to that interface. The 50 mV hysteresis helps the receiver maintain a stable decision as differential voltage crosses the signaling threshold. Because multiple branches and cable stubs can create reflections, the physical network must include appropriate termination and controlled routing. The receiver should be paired with an external RS-485 driver for bidirectional or broadcast operations.
Recomendado
Computer Peripherals and Legacy Equipment
The SN75175D is suitable for legacy computer peripherals and instrumentation that use balanced RS-422 or RS-485 communication links. Its four channels can consolidate several low-speed or moderate-speed differential inputs while presenting ordinary logic outputs to a host controller. The commercial 0°C to 70°C range is appropriate for many indoor peripherals, and the 5 V supply operation fits systems that already provide regulated 5 V. During integration, verify the host's logic voltage levels, enable sequencing, and handling of receiver failure states. Legacy status should also be checked against current product lifecycle requirements before new production use.
Recomendado
Test and Measurement Instrumentation
The SN75175D can serve as an input receiver in test and measurement instruments that exchange differential commands or data over RS-485 and RS-422 links. Four receiver channels reduce the number of packages needed when an instrument supports several instrument-to-controller connections. At up to 10 Mbps, the interface can handle short, controlled links without introducing a low-speed bottleneck, although cable loss and reflections remain important. Use isolated or protected cable-side circuits when measurements share ground with external equipment. The receiver's three-state output should be used deliberately when several instruments can connect to one controller bus.
Recomendado
Process-Control and Sensor Gateways
The SN75175D fits gateway equipment that collects differential signals from remote sensors or control modules over a balanced RS-485 network. Its four channels allow several field buses or node-monitoring inputs to be received by one package, while the enable input can coordinate participation on a shared segment. The 10 Mbps capability provides ample bandwidth for typical sensor traffic, but the design must still observe common-mode limits, grounding practice, and transient protection. The 0°C to 70°C range suits indoor gateways; use an appropriately qualified wider-temperature part when environmental conditions exceed that operating band.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para SN75175D — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | SN75175N | SN75175DE4 | SN75175DR | SN75175DG4 | SN65175D |
|---|---|---|---|---|---|---|
| Package | 16-pin SOIC (D) | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
Principais diferenciais
- Four differential channels in one 16-pin SOIC (vs SN75175N)
- Supports signaling rates up to 10 Mbps (vs SN75175DE4)
- Three-state outputs support shared-bus control (vs SN65175D)
Notas de projeto
Route each differential input pair together with consistent geometry and a continuous reference plane. Avoid long stubs, excessive vias, and branch connections on the cable side of the receiver. Place any protection network close to the connector and maintain a short, controlled path to the SN75175D inputs. This is particularly important at the upper end of the 10 Mbps capability because discontinuities can create reflections and differential-to-common-mode conversion.
Decouple the 5 V supply close to pin 10 with the capacitance recommended by the manufacturer datasheet, and provide a low-impedance ground connection at pin 5. Keep switching regulators, inductors, and high-current return paths away from the receiver inputs. Verify supply sequencing and ensure the device never operates outside the 4.75 V to 5.25 V range. If the board also powers noisy motors or relays, separate their surge-return paths from the receiver ground.
Do not assume that every SN75175 suffix is automatically interchangeable. Confirm enable polarity, output timing, receiver thresholds, temperature grade, qualification markings, and lifecycle status against the manufacturer ordering information. The SN75175D is receiver-only, so adding it to a design that expects an integrated transmitter requires a separate line driver. Also account for the last-time-buy status when planning production quantities and test coverage.
Use the 50 mV receiver hysteresis to its advantage by preventing repeated output transitions as the differential signal crosses the threshold, but do not treat hysteresis as a substitute for proper grounding and filtering. Keep the enable path away from noisy switching nodes, and consider pull resistors where control-state behavior during reset must be deterministic. Cable shields and chassis grounding should follow the topology of the peripheral or industrial equipment.
Informações de conformidade
Compliance attributes are not stated in the product and distributor information for SN75175D. The device is a commercial-temperature 5 V interface IC in a 16-pin SOIC package; no automotive qualification is claimed.