اطلاعیه آخرین فرصت خرید: SN75175D به پایان چرخه عمر نزدیک می‌شود. آخرین تاریخ سفارش: با ما تماس بگیرید. مشاهده قطعات جایگزین موجود →
Texas Instruments

SN75175D - Quad RS-485 Receiver, 10 Mbps | Texas Instruments

MPN: SN75175D ⚠ آخرین فرصت خرید
4.75 V to 5.25 V Vdss 16-pin SOIC (D) Package
حداقل سفارش: 1 |

SN75175D نمای کلی

The Texas Instruments SN75175D is a quadruple differential line receiver supporting RS-422, RS-423, and RS-485 balanced multipoint buses at rates up to 10 Mbps. The device provides four differential receiver channels, 50 mV receiver hysteresis, and three-state outputs in a 16-pin SOIC (D) package. Its 4.75 V to 5.25 V supply range and 0°C to 70°C operating-temperature range identify it as a commercial-temperature line-interface component.

A differential line receiver belongs to the interface IC hierarchy: it converts small voltage differences between two conductors into a digital logic signal. This conversion allows balanced signaling to reject common-mode noise, reduce ground-reference errors, and improve robustness in industrial environments. The SN75175 family is specifically intended for balanced multipoint data transmission rather than single-ended logic.

Each receiver converts its differential input pair to a logic output. The common enable control places the four outputs into a high-impedance state when required, allowing multiple receivers to share a bus without active-output contention. Three-state operation is particularly useful in bus architectures where several nodes may drive a shared line during different operating intervals. The 50 mV hysteresis helps prevent output chatter around the decision threshold.

The SN75175D supports a maximum signaling rate of 10 Mbps and uses a single 5 V supply. According to the manufacturer datasheet, the device is designed around EIA-485 and EIA-422A/23A balanced-interface requirements and CCITT recommendations. It contains no transmitters, so each channel is a receiver-only path; an external line driver is required when the design also needs to transmit.

Typical uses include industrial RS-485 equipment, data acquisition systems, instrumentation links, computer peripherals, and multipoint communication networks. Because the device supports four channels, one package can serve several independent differential inputs or four nodes on a multidrop bus when the enable function is managed correctly.

PCB design should preserve the differential signal path and provide a continuous return reference. Route each differential pair with matched geometry and avoid adding test pads or long branches that disturb impedance. Decouple the 5 V supply close to the device, and verify that the bus topology, termination, protection, and common-mode range match the cable and environmental conditions.

This page combines manufacturer specifications, compatible substitute references, interface-selection guidance, package details, and practical implementation notes. It helps engineers determine whether the SN75175D fits a legacy RS-485 or RS-422 design and how to validate a replacement before production release.

جایگزین‌های drop-in برای SN75175D — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای SN75175D (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Mounting Type, Maximum Data Rate, Number of Receivers.

Analog Devices
Package: 16-pin SOIC
Maximum Data Rate: 10Mbps
Number of Receivers: 4 channels
مقایسه با SN75175D →
Texas Instruments
Package: 16-pin plastic DIP (16-PDIP)
Mounting Type: Through-hole
مقایسه با SN75175D →

SN75175N

✅ جایگزین مستقیم
Texas Instruments
📦 16-pin SOIC (D)
Quad differential line receiver · 4 channels · 10 Mbit/s · 4.75 V to 5.25 V · 5 V · Three-state output · RS-485, RS-422, RS-423

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

SN75175DE4

✅ جایگزین مستقیم
📦 16-pin SOIC (D)
Same 4.75 V, 10 Mbps quad receiver architecture and package; grade and production-code details require confirmation.

📋 جایگزین مرجع (خارج از کاتالوگ)

SN75175DR

✅ جایگزین مستقیم
📦 16-pin SOIC (D)
Same receiver architecture and footprint; operating-grade and suffix-specific differences require confirmation.

📋 جایگزین مرجع (خارج از کاتالوگ)

SN75175DG4

✅ جایگزین مستقیم
📦 16-pin SOIC (D)
Same quad differential receiver and 16-pin SOIC footprint; qualification and ordering-code differences require confirmation.

📋 جایگزین مرجع (خارج از کاتالوگ)

SN65175D

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
Texas Instruments
📦 16-pin SOIC (D)
Quadruple differential line receiver · 4 receivers · 0 drivers · RS-422, RS-423, RS-485 · 4.75 V to 5.25 V · 50 mV · 3-state · -40 °C to 85 °C

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

SN75175D مشخصات

Receiver Type Quad differential line receiver
Number of Receivers 4
Supported Protocols RS-422, RS-423, RS-485
Maximum Data Rate 10 Mbps
Supply Voltage Range 4.75 V to 5.25 V
محدوده دمای کاری 0°C to 70°C
Receiver Hysteresis 50 mV
Output State Control Three-state outputs
Duplex Support Receiver-only; no integrated transmitter
بسته‌بندی 16-pin SOIC (D)
نوع نصب Surface mount
Shipping Package Tube

پیکربندی پین SN75175D

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
پین 1 1A — Channel 1 non-inverting differential input
پین 2 1Y — Channel 1 logic output
پین 3 2A — Channel 2 non-inverting differential input
پین 4 2Y — Channel 2 logic output
پین 5 GND — Ground connection
پین 6 3Y — Channel 3 logic output
پین 7 3A — Channel 3 non-inverting differential input
پین 8 4Y — Channel 4 logic output
پین 9 4A — Channel 4 non-inverting differential input
پین 10 VCC — Positive supply connection
پین 11 EN — Common output-enable input
پین 12 NC — Not connected (per datasheet)
پین 13 NC — Not connected (per datasheet)
پین 14 2B — Channel 2 inverting differential input
پین 15 1B — Channel 1 inverting differential input
پین 16 4B — Channel 4 inverting differential input

کاربردهای معمول

SN75175D مناسب است برای 6 کاربردs: Industrial RS-485 Data Acquisition, RS-422 Point-to-Point Links, Multipoint Communication Network, Computer Peripherals and Legacy Equipment, Test and Measurement Instrumentation, Process-Control and Sensor Gateways.

🏭

Industrial RS-485 Data Acquisition

The SN75175D is appropriate for receiving four balanced RS-485 signals in industrial data-acquisition equipment because it supports rates up to 10 Mbps with 50 mV hysteresis and three-state outputs. Place one receiver channel on each protected differential pair and manage the common enable so unused outputs enter a high-impedance state. The 4.75 V to 5.25 V supply range supports conventional 5 V interface logic, while the 0°C to 70°C rating suits controlled indoor equipment. External surge protection, chassis grounding, and cable-side isolation should be evaluated because the receiver IC alone does not provide those protections.

🌐

RS-422 Point-to-Point Links

The SN75175D can serve as the receiving half of a multi-channel RS-422 interface, converting balanced differential inputs into CMOS-compatible logic signals. Its four channels allow a compact receiver arrangement when a system carries several independent point-to-point links. At rates up to 10 Mbps, cable length, connector geometry, source termination, and receiver input characteristics must be evaluated together. The three-state outputs also permit bus sharing when the host can disable the receiver cleanly. Confirm output enable polarity and logic thresholds in the circuit design because those details control whether the device drops into the existing interface correctly.

🔗

Multipoint Communication Network

A multidrop RS-485 network benefits from the SN75175D's four differential receiver channels and three-state output capability. Each receiver can monitor a different node while the enable function keeps outputs inactive when the bus is not assigned to that interface. The 50 mV hysteresis helps the receiver maintain a stable decision as differential voltage crosses the signaling threshold. Because multiple branches and cable stubs can create reflections, the physical network must include appropriate termination and controlled routing. The receiver should be paired with an external RS-485 driver for bidirectional or broadcast operations.

🖥️

Computer Peripherals and Legacy Equipment

The SN75175D is suitable for legacy computer peripherals and instrumentation that use balanced RS-422 or RS-485 communication links. Its four channels can consolidate several low-speed or moderate-speed differential inputs while presenting ordinary logic outputs to a host controller. The commercial 0°C to 70°C range is appropriate for many indoor peripherals, and the 5 V supply operation fits systems that already provide regulated 5 V. During integration, verify the host's logic voltage levels, enable sequencing, and handling of receiver failure states. Legacy status should also be checked against current product lifecycle requirements before new production use.

🔧

Test and Measurement Instrumentation

The SN75175D can serve as an input receiver in test and measurement instruments that exchange differential commands or data over RS-485 and RS-422 links. Four receiver channels reduce the number of packages needed when an instrument supports several instrument-to-controller connections. At up to 10 Mbps, the interface can handle short, controlled links without introducing a low-speed bottleneck, although cable loss and reflections remain important. Use isolated or protected cable-side circuits when measurements share ground with external equipment. The receiver's three-state output should be used deliberately when several instruments can connect to one controller bus.

🧩

Process-Control and Sensor Gateways

The SN75175D fits gateway equipment that collects differential signals from remote sensors or control modules over a balanced RS-485 network. Its four channels allow several field buses or node-monitoring inputs to be received by one package, while the enable input can coordinate participation on a shared segment. The 10 Mbps capability provides ample bandwidth for typical sensor traffic, but the design must still observe common-mode limits, grounding practice, and transient protection. The 0°C to 70°C range suits indoor gateways; use an appropriately qualified wider-temperature part when environmental conditions exceed that operating band.

خلاصه محصولات پیشنهادی

SN75175D Texas Instruments استفاده‌شده در: Industrial RS-485 Data Acquisition, RS-422 Point-to-Point Links, Multipoint Communication Network, Computer Peripherals and Legacy Equipment, Test and Measurement Instrumentation, Process-Control and Sensor Gateways SN75175N Texas Instruments استفاده‌شده در: Industrial RS-485 Data Acquisition SN75175DG4 Same-family receiver option for supply planning استفاده‌شده در: Multipoint Communication Network SN75175DE4 Same-family receiver candidate for legacy-equipment review استفاده‌شده در: Computer Peripherals and Legacy Equipment SN65175D Texas Instruments استفاده‌شده در: Test and Measurement Instrumentation SN75175DR Same-family receiver candidate for gateway sourcing استفاده‌شده در: Process-Control and Sensor Gateways
What is the SN75175D and what can it replace?
The SN75175D is a Texas Instruments quadruple differential line receiver for RS-422, RS-423, and RS-485 buses. According to the manufacturer datasheet, it provides four receiver channels with three-state outputs, 50 mV hysteresis, and operation at rates up to 10 Mbps. It can replace a compatible 16-pin SOIC quad receiver after confirming enable behavior, logic polarity, supply requirements, temperature range, and bus timing against the original design.
Where can I download the SN75175D datasheet PDF?
The official SN75175D datasheet is available through the Texas Instruments product and literature pages. The manufacturer literature entry identifies the SN75175 as a quadruple differential line receiver and provides the operating range and package details needed for initial qualification. Use the pin-description table, recommended operating conditions, and electrical characteristics from the manufacturer datasheet when assigning PCB functions and validating a substitute.
Where can I find the SN75175D pinout?
The SN75175D pinout is published in the manufacturer datasheet for the 16-pin SOIC (D) package. The device has four differential input channels, four corresponding logic outputs, supply and ground connections, a common enable input, and two no-connect positions. Use the numbered package drawing to map each input pair and output before laying out a board or qualifying a replacement.
What are the key specifications of SN75175D that engineers should know?
The SN75175D is a four-channel differential receiver with a 4.75 V to 5.25 V supply range, a 10 Mbps maximum data rate, 50 mV hysteresis, three-state outputs, and a 0°C to 70°C operating range. According to the Texas Instruments datasheet, it is designed for RS-422, RS-423, and RS-485 balanced transmission. Its most important design limits are the single 5 V supply, commercial temperature range, and absence of integrated drivers.
Is the SN75175D still in stock and available for purchase?
The manufacturer lists SN75175D with a last-time-buy lifecycle status, so new supply may be limited while remaining inventory is depleted. Stock levels and production schedules can change without notice. Use the Request a Quote form on this page to ask about current availability, minimum order quantity, lead time, and the exact Texas Instruments ordering code you intend to release.
What is the current price of SN75175D?
Pricing for the SN75175D depends on order quantity, remaining manufacturer inventory, and any legacy-market conditions. Because this device has a last-time-buy status, a quotation should reflect the requested quantity and suffix rather than a general catalog assumption. Use the Request a Quote form on this page for a current unit price, extended price, and availability confirmation.
What is the lead time for SN75175D?
The SN75175D lead time depends on remaining last-time-buy inventory and the quantity being ordered. A dated schedule for this exact MPN should be requested through the Request a Quote form on this page. Include the required delivery date and acceptable package quantity so the quotation can reflect the actual manufacturing and distribution position.
Can SN75175N replace SN75175D?
The SN75175N can serve as a close replacement candidate because cross-reference information describes the same 16-pin SOIC interface, 4.75 V supply operation, and 10 Mbps receiver performance. Before approving the substitution, verify enable polarity, output timing, receiver thresholds, temperature limits, and qualification markings. A footprint match alone does not establish complete production equivalence.
What is the difference between SN75175D and SN75175DE4?
The SN75175D and SN75175DE4 are presented as functionally consistent, pin-compatible 16-pin SOIC quad differential receivers. Their main selection point is the device-grade and ordering-code suffix rather than the receiver architecture. Review the manufacturer ordering table for operating-temperature grade, qualification markings, production status, and any marking or traceability requirements before treating them as equivalent releases.
When should I choose SN75175D instead of SN75175N?
Choose the SN75175D when its exact ordering code, 0°C to 70°C operating range, 16-pin SOIC package, and production status match the assembly plan. Choose SN75175N when it offers the required availability or grade while preserving the same receiver function and footprint. The decision should follow a comparison of lifecycle status, temperature range, qualification, marking, and current lot traceability.
Is SN75175D suitable for an RS-485 receiver interface?
The SN75175D is suitable for receiving balanced RS-485 signals when its supply, enable, logic-level, temperature, and timing requirements match the system. It supports data rates up to 10 Mbps and includes three-state outputs for shared-bus designs. The host transceiver still requires protection, grounding, termination, and common-mode-range evaluation for the actual cable and industrial environment.
What is the best drop-in replacement for SN75175D?
The closest documented replacements for SN75175D are the SN75175N, SN75175DE4, SN75175DR, SN75175DG4, and SN65175D candidates in the same 16-pin SOIC family. The best production choice depends on availability, temperature grade, qualification, enable polarity, and timing compatibility. Compare each candidate against the manufacturer datasheet and test the complete interface before releasing a substitution.
Is SN75175D the same as SN75175DR?
The SN75175D and SN75175DR use the same core quadruple differential receiver architecture and a 16-pin SOIC package, but their ordering suffixes can identify different grades or production details. Treat them as compatible candidates rather than automatically identical parts. Confirm operating temperature, lifecycle status, qualification, markings, and the electrical-characteristics table before substitution.
Can one SN75175D package receive four RS-485 buses?
Yes, the SN75175D contains four independent differential receiver channels and can receive four separate RS-485 pairs when channel routing, enable control, grounding, and signal integrity permit. On a multidrop bus, each receiver may instead monitor one node while the common enable function controls output states. Correct bus topology and output-enable sequencing are essential to prevent contention.
Does SN75175D include an RS-485 transmitter?
No, the SN75175D contains four differential receivers and no integrated drivers. A separate line-driver IC is required when the same node must transmit as well as receive. According to the manufacturer description, the device supports RS-422, RS-423, and RS-485 reception, with three-state outputs for controlled bus participation.

داده‌های مرجع مهندسی برای SN75175D — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the SN75175D for a new or maintained design that requires four RS-422, RS-423, or RS-485 receiver channels, a 4.75 V to 5.25 V supply, and operation from 0°C to 70°C. Select SN65175D when the wider -40°C to 85°C range is required and its enable, timing, and electrical characteristics remain acceptable. SN75175N, SN75175DE4, SN75175DR, and SN75175DG4 are same-family candidates for supply and lifecycle planning, but their grade and suffix specifications must be compared with the installed device. The target is receiver-only, so a separate transmitter is required for bidirectional RS-485 nodes. Before approving any replacement, verify package pinout, enable polarity, threshold behavior, propagation timing, supply range, qualification markings, and lifecycle commitments.

مقایسه با جایگزین‌ها

پارامتر این محصول SN75175N SN75175DE4 SN75175DR SN75175DG4 SN65175D
Package 16-pin SOIC (D) 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments

تفاوت‌های کلیدی

  • Four differential channels in one 16-pin SOIC (در مقابلSN75175N)
  • Supports signaling rates up to 10 Mbps (در مقابلSN75175DE4)
  • Three-state outputs support shared-bus control (در مقابلSN65175D)

یادداشت‌های طراحی

Route each differential input pair together with consistent geometry and a continuous reference plane. Avoid long stubs, excessive vias, and branch connections on the cable side of the receiver. Place any protection network close to the connector and maintain a short, controlled path to the SN75175D inputs. This is particularly important at the upper end of the 10 Mbps capability because discontinuities can create reflections and differential-to-common-mode conversion.

Decouple the 5 V supply close to pin 10 with the capacitance recommended by the manufacturer datasheet, and provide a low-impedance ground connection at pin 5. Keep switching regulators, inductors, and high-current return paths away from the receiver inputs. Verify supply sequencing and ensure the device never operates outside the 4.75 V to 5.25 V range. If the board also powers noisy motors or relays, separate their surge-return paths from the receiver ground.

Do not assume that every SN75175 suffix is automatically interchangeable. Confirm enable polarity, output timing, receiver thresholds, temperature grade, qualification markings, and lifecycle status against the manufacturer ordering information. The SN75175D is receiver-only, so adding it to a design that expects an integrated transmitter requires a separate line driver. Also account for the last-time-buy status when planning production quantities and test coverage.

Use the 50 mV receiver hysteresis to its advantage by preventing repeated output transitions as the differential signal crosses the threshold, but do not treat hysteresis as a substitute for proper grounding and filtering. Keep the enable path away from noisy switching nodes, and consider pull resistors where control-state behavior during reset must be deterministic. Cable shields and chassis grounding should follow the topology of the peripheral or industrial equipment.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

Compliance attributes are not stated in the product and distributor information for SN75175D. The device is a commercial-temperature 5 V interface IC in a 16-pin SOIC package; no automotive qualification is claimed.

تاریخ تأیید داده‌ها: 2026-11-09 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

sn75175d datasheet SN75175D datasheet PDF SN75175D pinout SN75175D SOIC-16 SN75175D RS-485 receiver SN75175D RS-422 receiver SN75175D equivalent SN75175D replacement SN75175D cross reference SN75175D vs SN75175N Texas Instruments SN75175D SN75175D price SN75175D stock SN75175D application circuit SN75175D 10 Mbps receiver

قطعات و اصطلاحات مرتبط

Texas Instruments SN75175D SN75175 SN75175N SN75175DE4 SN75175DR SN75175DG4 SN65175D quad differential line receiver receiver IC interface IC RS-485 RS-422 RS-423 EIA-485 EIA-422A/23A CCITT recommendations three-state output receiver hysteresis differential signaling balanced multipoint bus 16-pin SOIC SOIC family surface-mount package digital line interface
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ