STM32F070C6T6 - 48MHz Cortex-M0 USB MCU | ST
N.º da peça: STM32F070C6T6 ✓ AtivoSTM32F070C6T6 Visão geral
A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interface circuitry on one device. The STM32F070C6T6 belongs to the STM32F0 family, where the Arm Cortex-M0 core provides a low-complexity RISC architecture for embedded control. Its USB 2.0-compatible full-speed device peripheral adds a practical communication path for configuration, data exchange, and firmware update systems without requiring a separate USB interface controller.
The principal device characteristics are a 48 MHz operating frequency, 32-bit Arm Cortex-M0 processing, 32 KB of Flash, and full-speed USB device support. The manufacturer identifies the part in a 48-LQFP 7 x 7 mm package. This combination makes the device suitable for compact embedded products that need USB connectivity but not the processing capacity, memory, or pin count of a larger STM32 member.
The USB device peripheral includes an internal USB PHY with embedded pull-up support and battery-charging detection according to the Battery Charging Specification Revision 1.2, as stated by STMicroelectronics. These features simplify USB-connected peripheral designs by reducing external interface requirements. Designers should still account for the USB data signaling, power, clock, decoupling, and firmware-support requirements of the complete application circuit.
Typical uses include USB-connected control accessories, compact data-collection equipment, human-interface devices, simple programmers, and low-cost embedded control modules. The 48-LQFP package provides a useful balance between routing flexibility and board size, while the dedicated USB interface makes the MCU suitable for designs where a dedicated USB interface would add cost and board area.
For PCB implementation, follow the pin-definition table and recommended layout guidance in the manufacturer datasheet. Place the required bypass capacitors adjacent to the power pins, keep USB data routing short and impedance-controlled, and provide appropriate clock and reset support. The exposed thermal arrangement and power dissipation should be checked against the final operating current and ambient temperature.
This product page combines the manufacturer electrical definitions with application guidance, drop-in replacement analysis, and practical PCB considerations. It is intended to help engineers determine whether the 48 MHz Cortex-M0 core, 32 KB Flash configuration, USB device support, and 48-LQFP footprint fit a specific embedded design before starting layout or firmware integration.
Alternativas drop-in para STM32F070C6T6 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com STM32F070C6T6 (mesmo formato e footprint) — diferindo em Flash Memory, Package, Product Type, RoHS Status, Series.
STM32F030C6T6
✅ Drop-In✓ Em estoque
$1.15 / unidade
Ver ficha técnica →STM32F031C6T6
✅ Drop-InConsulte o preço
Ver ficha técnica →STM32F070C8T6
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
STM32F072C6T6
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
STM32F072C8T6
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →STM32F070C6T6 Classificações máximas e características elétricas
| Product Type | 32-bit microcontroller |
| Processor Core | Arm Cortex-M0 |
| Architecture | 32-bit RISC |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 32 KB |
| Flash Organization | 32K x 8 bits |
| USB Interface | Full-speed USB 2.0 device |
| USB PHY | Internal USB full-speed PHY |
| USB Pull-Up | Embedded DP pull-up |
| Battery Charging Detection | Battery Charging Specification Revision 1.2 |
| Encapsulamento | 48-LQFP, 7 x 7 mm |
| Contagem de pinos | 48 pins |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do STM32F070C6T6 48-lqfp, 7 x 7 mm
Configuração de pinos para STM32F070C6T6 (pacote 48-lqfp, 7 x 7 mm). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para STM32F070C6T6.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
STM32F070C6T6 é adequado para 6 aplicaçãos: USB-connected Control Accessory, Human-Interface Device, USB Data-Collection Module, Compact Programmer and Configuration Tool, Industrial Sensor Interface, USB Communication Bridge.
USB-connected Control Accessory
The STM32F070C6T6 fits a compact USB control accessory because it combines a 48 MHz Arm Cortex-M0 core with a full-speed USB device peripheral in a 48-LQFP 7 x 7 mm package. The internal USB PHY and embedded DP pull-up reduce the external interface component count. Place the MCU between the USB connector and the accessory’s control logic, then implement enumeration and command handling in the device firmware. The 32 KB Flash capacity is suitable for protocol and control code, although it requires disciplined image sizing when USB descriptors, update logic, and application firmware are combined.
Recomendado
Human-Interface Device
The STM32F070C6T6 supports a USB human-interface device by using its full-speed USB 2.0-compatible peripheral for HID traffic while the Cortex-M0 core handles button states, indicators, and control logic. Its 48 MHz operating frequency provides adequate response for standard polling-based HID workloads, while the 48-LQFP package leaves access to a broad pin complement for switches, sensors, or status LEDs. Firmware should implement the USB stack, report descriptors, debounce handling, and suspend behavior. Board validation should include enumeration testing across the intended host operating systems and cable or connector configurations.
Recomendado
USB Data-Collection Module
The STM32F070C6T6 is appropriate for a small data-collection module that periodically sends measurements to a USB host. The 48 MHz Cortex-M0 core can supervise sampling and control routines, while the integrated full-speed USB device interface handles the host connection without a separate USB bridge controller. The 32 KB Flash footprint suits a focused acquisition application with local configuration and a modest protocol stack. Designers should size the firmware against the full firmware image, implement buffering appropriate to the host polling interval, and verify timing under worst-case sample rates and bus-traffic conditions.
Recomendado
Compact Programmer and Configuration Tool
The STM32F070C6T6 can serve as the controller in a compact programmer or configuration tool that connects to a target board over USB. Its full-speed device capability supports command exchange and firmware transfer, while the 48 MHz Cortex-M0 core executes protocol handling and target-control logic. The 48-LQFP package is useful when the product needs both USB and a conventional set of general-purpose interfaces. A production design should add protection for the externally exposed target connector, define robust cable or connector handling, and validate the programmed target across voltage levels and devices supported by the tool.
Recomendado
Industrial Sensor Interface
The STM32F070C6T6 is suitable for a compact industrial sensor interface that must collect local measurements and expose status or configuration data over USB. Its 48 MHz processing rate and integrated USB device interface support responsive control and data transfer without requiring a high-performance application processor. The 48-LQFP package provides a practical balance between pin availability and board area. Engineers should define sensor timing, input conditioning, isolation requirements, and grounding independently of the MCU, then validate the complete measurement chain under the intended environmental and interference conditions.
Recomendado
USB Communication Bridge
The STM32F070C6T6 can implement a protocol bridge between a USB host and an embedded peripheral interface. The Cortex-M0 core handles framing, device state, and the translation between USB transactions and the target interface, while the internal full-speed PHY supports direct USB connectivity. Its 32 KB Flash capacity is appropriate for a focused bridge firmware image but can become restrictive when several protocol layers, diagnostics, and update mechanisms are included. Confirm that the selected STM32F030K6T6 companion-class MCU has sufficient resources if the bridge also performs local real-time control.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para STM32F070C6T6 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | STM32F030C6T6 | STM32F031C6T6 | STM32F070C8T6 | STM32F072C6T6 | STM32F072C8T6 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 48-LQFP (7x7) | 48-LQFP (7x7) | 48-LQFP (7x7) | 48-LQFP (7x7) | 48-LQFP (7x7) | 48-LQFP (7x7) |
| Processor Core | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 |
| Maximum CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 64 KB | 32 KB | 64 KB |
| USB Interface | Full-speed USB 2.0 device | Not present | Not present | Full-speed USB 2.0 device | Full-speed USB 2.0 device | Full-speed USB 2.0 device |
| Programming Temperature Indicator | T6 suffix | T6 suffix | T6 suffix | T6 suffix | T6 suffix | T6 suffix |
Principais diferenciais
- Integrated full-speed USB device interface (vs STM32F030C6T6)
- USB battery-charging detection support (vs STM32F031C6T6)
- Higher Flash option is available within the same family (vs STM32F070C8T6)
- Same footprint with a larger Flash option (vs STM32F072C8T6)
Notas de projeto
Follow the STMicroelectronics recommended land pattern for the 48-LQFP 7 x 7 mm package and preserve pin-1 orientation marks on both the PCB and component reel. Place decoupling capacitors adjacent to the relevant supply pins and connect their ground returns through the shortest practical path. Keep USB D+ and D- traces away from switching nodes and high-current return paths, then apply the USB impedance and routing guidance specified in the manufacturer datasheet.
Calculate the supply requirement from the 48 MHz operating condition, USB transceiver demand, enabled peripherals, and the load attached to any general-purpose output. Include startup and bus-suspend states rather than evaluating only the maximum active current. Confirm that the USB host or cable power source can support the complete device load, and apply the manufacturer’s recommended supply and decoupling network without adding large bulk capacitance that could interfere with startup behavior.
Do not treat every 48-LQFP STM32F0 device as an interchangeable controller. The STM32F070C6T6 includes full-speed USB, while alternatives in the same footprint may differ in USB availability, flash capacity, peripheral multiplexing, startup behavior, and firmware support. Before approving a substitution, compare the exact pin-description table, clock tree, interrupt mapping, USB implementation, memory configuration, and device-specific errata, then run the existing firmware on the candidate board.
Separate USB signaling from analog or sensitive measurement paths and provide a continuous ground reference beneath the routed pair. Place the USB connector, protection components, and MCU interface in a direct signal path. Use a common low-impedance ground-plane strategy so return current does not cross sensitive divider or sensor-reference areas. Validate signal integrity with the intended cable, host, supply configuration, and enclosure because connector and harness details can materially affect full-speed USB performance.
Informações de conformidade
RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status are not established by the manufacturer product-page extract for this exact orderable MPN.