SY89529LZH - 200MHz Spread-Spectrum Clock | Microchip
N.º da peça: SY89529LZH ✗ Fim de vidaSY89529LZH Visão geral
A clock synthesizer is an integrated timing device that converts a stable reference frequency into one or more controlled output frequencies. The SY89529 belongs to the hierarchy of clock and frequency synthesizer ICs, PLL-based clock generators, and timing-control semiconductors. Its spread-spectrum operation varies the output frequency over time, reducing energy concentration at a single clock frequency and helping lower radiated emissions from systems that use the clock as a data source.
Key features include a maximum output frequency of 200 MHz, a PLL architecture, a crystal-based reference input, and LVPECL clock output. The spread-spectrum modulation is adjustable up to 0.5%, while spread-spectrum modulation can provide a 7 dB reduction in EMI. These characteristics make the device useful where both precise edge placement and controlled spectral spreading are required.
The SY89529 uses a PLL to develop a high-frequency clock from the 16.66 MHz crystal source. This architecture permits the synthesizer to produce a much higher output frequency than its reference while maintaining a controlled relationship between input and output edges. The LVPECL output is suited to high-speed digital systems operating on a low-voltage positive-referenced ECL level, whereas the LVTTL and LVCMOS-compatible interfaces broaden the supported logic environment.
Typical uses include processor and communications-clock distribution, high-speed serial links, network interface equipment, and embedded systems requiring reduced electromagnetic emissions. The 200 MHz LVPECL output can feed retimers, serializers, FPGAs, or other clock-domain components. The 28-pin SOIC package permits conventional surface-mount assembly, although careful decoupling and controlled-impedance routing remain essential at 200 MHz.
Designers should follow the manufacturer datasheet for reference-crystal selection, loop-filter recommendations, power-supply sequencing, and output termination. LVPECL outputs generally require an appropriate termination network and compatible biasing arrangement. PCB placement should minimize clock-loop area, keep the crystal path compact, and provide low-impedance ground and power-return paths to limit jitter and radiated emissions.
This product summary consolidates the device specifications, lifecycle status, application guidance, and design considerations engineers need to evaluate the SY89529LZH for spread-spectrum clock generation.
Alternativas drop-in para SY89529LZH — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasSY89529LZH Especificações
| Device Type | Precision spread-spectrum clock synthesizer |
| Supply Voltage Range | 3.135 V to 3.465 V |
| Nominal Supply Voltage | 3.3 V |
| Maximum Output Frequency | 200 MHz |
| Reference Crystal Frequency | 16.66 MHz |
| PLL | Yes |
| Primary Clock Output | LVPECL |
| Logic Compatibility | LVTTL and LVCMOS compatible |
| Maximum Spread-Spectrum Modulation | 0.5% |
| EMI Reduction | 7 dB with spread-spectrum modulation |
| Number of Circuits | 1 |
| Encapsulamento | 28-pin SOIC |
| Package Width | 7.50 mm |
| Tipo de montagem | Surface mount |
| Shipping Package | Tube |
| Product Series | Precision Edge |
| Product Status | Obsolete |
Guia de Configuração de Pinos do SY89529LZH tube
Configuração de pinos para SY89529LZH (pacote tube). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para SY89529LZH.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
SY89529LZH é adequado para 6 aplicaçãos: High-Speed Serial Communications, Processor and FPGA Clock Distribution, Network Interface Equipment, EMI-Controlled Digital Systems, High-Speed Data Conversion and Retiming, Legacy Industrial Control Platforms.
High-Speed Serial Communications
The SY89529LZH fits high-speed serial communications equipment that needs a stable 200 MHz LVPECL clock while limiting narrowband EMI concentration. Its PLL multiplies a 16.66 MHz crystal reference to the specified 200 MHz output, and spread-spectrum modulation can shift energy across a controlled frequency range with modulation up to 0.5%. Place the output near the serializer or retimer, use the termination network specified in the manufacturer application circuit, and preserve a continuous ground return. Spread-spectrum operation can lower a measured emissions peak by the stated 7 dB under suitable system conditions, although cable, connector, and enclosure resonances still require separate control.
Recomendado
Processor and FPGA Clock Distribution
The SY89529LZH is appropriate for clock distribution into processor, FPGA, or high-speed ASIC systems operating near the 200 MHz maximum output of the device. A PLL-based design provides a controlled relationship between the 16.66 MHz reference and the generated LVPECL clock, while the adjustable spread-spectrum control can reduce the spectral peak of a repetitive clock. The clock net should use a short, impedance-controlled route with a defined termination arrangement and minimal stubs. Because the output is LVPECL rather than a conventional CMOS clock, the receiving device must support the required levels and termination topology.
Recomendado
Network Interface Equipment
Network interface equipment can use the SY89529LZH when a common 200 MHz reference clock is needed by multiple high-speed paths and reduced spectral concentration is valuable. The 3.3 V supply requirement and 28-pin SOIC package fit conventional mixed-signal board assembly, while the LVPECL output supports compatible high-speed clock receivers. Engineers should establish a low-impedance distribution topology, isolate the oscillator reference from noisy switching stages, and avoid adding unnecessary branch stubs. EMI reduction depends on the modulation setting, clock amplitude, trace impedance, enclosure seams, and connector filters, so the stated 7 dB improvement should be treated as a device-level characteristic rather than a guaranteed system-level result.
Recomendado
EMI-Controlled Digital Systems
The SY89529LZH is useful in digital systems where a fixed-frequency clock would create a strong spectral peak in an emissions measurement. Its spread-spectrum modulation control reaches 0.5%, allowing clock energy to spread across nearby frequencies while the PLL maintains a controlled relationship with the 16.66 MHz reference. The device can therefore help reduce emissions sensitivity without abandoning a precise 200 MHz clock. To obtain predictable results, configure the modulation using the manufacturer guidance, preserve a short crystal path, decouple the 3.3 V supply locally, and apply the specified LVPECL termination. System verification should include both time-domain clock-quality checks and spectral emissions measurements.
Recomendado
High-Speed Data Conversion and Retiming
The SY89529LZH can supply a 200 MHz LVPECL reference to high-speed data-conversion, retiming, or serialization paths that require stable edge placement and controlled spectral occupancy. The PLL-based architecture produces the high-rate output from a low-frequency crystal reference, while spread-spectrum modulation offers an additional mechanism for reducing narrowband EMI. The clock should be routed as a controlled-impedance transmission line with the termination arrangement required by the receiver interface. Supply and ground planes must provide low-inductance return paths close to the device, and the reference oscillator area should remain physically separated from switching power stages and high-current output circuitry to minimize jitter coupling.
Recomendado
Legacy Industrial Control Platforms
The SY89529LZH is suitable for a legacy industrial control platform that still relies on its established 200 MHz LVPECL clock architecture and requires controlled spread-spectrum operation for emissions management. The 3.135 V to 3.465 V operating range and 28-pin SOIC package support repair, qualification, or continuation of an existing board design. Because the device is obsolete, engineers should document whether the application requires an exact replacement, a functional redesign, or a last-time-buy arrangement. Any replacement program must validate clock frequency, LVPECL levels, jitter, spread-spectrum behavior, crystal startup, and electromagnetic-emissions performance rather than relying only on a nominal maximum-frequency comparison.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para SY89529LZH — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Brand | Microchip Technology |
| Package | 28-pin SOIC |
| Device Type | Precision spread-spectrum clock synthesizer |
| Supply Voltage Range | 3.135 V to 3.465 V |
| Maximum Output Frequency | 200 MHz |
| Reference Input | 16.66 MHz crystal |
| Output Logic | LVPECL |
| PLL | Yes |
| Maximum Spread-Spectrum Modulation | 0.5% |
| Product Status | Obsolete |
Principais diferenciais
- Combines a 200 MHz output with adjustable spread-spectrum modulation (vs Conventional fixed-frequency 200 MHz clock)
- Provides a stated EMI reduction in spread-spectrum operation (vs Fixed-frequency oscillator without spectral spreading)
- Uses a PLL architecture with a low-frequency crystal reference (vs Direct fixed-frequency oscillator)
Notas de projeto
Keep the 16.66 MHz crystal, its load components, and the associated SY89529LZH pins physically short and away from high-current switching nodes. Follow the manufacturer application circuit for the crystal load capacitance and grounding arrangement. A compact oscillator loop reduces susceptibility to noise pickup, parasitic capacitance, and startup problems. Preserve a continuous ground reference beneath the clock section so reference jitter and spur performance are not degraded by return-path discontinuities.
Treat the 200 MHz LVPECL output as a controlled-impedance clock network and apply the termination arrangement specified in the manufacturer datasheet. Avoid long stubs, test pads without defined treatment, and unnecessary branch loads. Keep the clock route away from noisy analog inputs and switching-node copper, and verify rise time, ringing, jitter, and receiver compatibility on the assembled board. Spread-spectrum modulation reduces spectral concentration but does not correct a poor physical clock topology.
Provide a low-impedance 3.3 V supply and place the required bypass capacitors close to the power and ground pins using short, wide connections. Estimate the regulator dissipation with P = (VIN − VOUT) × IOUT before committing to the layout, because an LDO requires headroom and dissipates the voltage-drop difference as heat. Use the manufacturer maximum ratings for current and operating temperature, and confirm package thermal performance under the maximum expected clock load.
Validate the completed system with both conducted and radiated emissions measurements because the specified 7 dB EMI reduction is not a guarantee for every board or enclosure. Document the spread-spectrum modulation setting, clock amplitude, termination, and operating mode used during testing. Compare results with the same design operating at fixed frequency to quantify the system-level benefit and check that no new discrete emissions line appears within protected bands.
Informações de conformidade
Compliance declarations are not stated in the available manufacturer document text. Review the current Microchip product-material declarations before using the part in a regulated design.