SY89875UMI - 2GHz 1:2 LVDS Clock Buffer | Microchip
N.º da peça: SY89875UMI ✓ AtivoSY89875UMI Visão geral
A clock buffer is a digital timing IC that receives a reference clock and reproduces or distributes that signal with low timing degradation. Clock dividers reduce a clock to a lower frequency, fanout buffers create multiple outputs, and differential signaling carries timing information across a PCB using complementary data pairs. These functions place the SY89875UMI within the clock and timing IC hierarchy of digital logic and semiconductor-based system timing.
The principal features of the SY89875UMI include a 1:2 fanout ratio, programmable clock division, differential input support, LVDS output support, and internal termination. The manufacturer identifies the device as accepting any differential input type while supporting CML, HSTL, LVDS, and LVPECL input signaling. This versatility allows the buffer to operate near several common high-speed clocking environments without requiring a separate input-conversion stage.
At the circuit level, the SY89875UMI combines a programmable divider with two complementary clock outputs. Differential clock distribution reduces sensitivity to common-mode noise when the output is routed through controlled-impedance PCB traces. Internal input termination helps control the impedance presented by the differential input network, although the exact termination value and implementation details should be confirmed in the manufacturer datasheet and reference design before final signal-integrity calculations.
Typical uses include LVDS clock distribution for communications equipment, programmable clock generation in server and networking systems, fanout to multiple downstream logic devices, and timing support in industrial or test systems. The 2 GHz operating limit suits high-speed digital backplanes and interfaces, while the 1:2 fanout allows one source clock to feed two destinations.
PCB implementation requires careful attention to differential pair geometry, return-path continuity, and the exposed thermal pad. The 16-VFQFN footprint also demands an unobstructed ground and thermal-via arrangement beneath the device. Verify the complete pin assignment, input logic levels, divider configuration method, and output termination requirements against the manufacturer datasheet before releasing the layout.
This page organizes the SY89875UMI specifications, sourcing questions, functional use cases, package information, and confirmed same-brand replacement information into an engineering-focused guide. The design notes and comparison tables also identify which parameters require confirmation before PCB or system-level qualification.
Alternativas drop-in para SY89875UMI — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com SY89875UMI (mesmo formato e footprint) — diferindo em Fanout Ratio.
SY89875UMG
✅ Drop-InConsulte o preço
Ver ficha técnica →SY89875UMI Especificações
| Tensão de alimentação | 2.5 V |
| Maximum Operating Frequency | 2 GHz |
| Fanout Ratio | 1:2 (unitless) |
| Configuração de saída | 2 differential LVDS outputs |
| Input Configuration | Any differential input type |
| Supported Input Standards | CML, HSTL, LVDS, and LVPECL |
| Internal Termination | Yes |
| Clock Division | Programmable |
| Product Series | Precision Edge |
| Encapsulamento | 16-VFQFN exposed pad (16-MLF) |
| Contagem de pinos | 16 pins |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do SY89875UMI 16-vfqfn exposed pad (16-mlf)
Configuração de pinos para SY89875UMI (pacote 16-vfqfn exposed pad (16-mlf)). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para SY89875UMI.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
SY89875UMI é adequado para 6 aplicaçãos: High-Speed LVDS Clock Distribution, Networking and Communications Equipment, Server and Storage Backplanes, Programmable Clock Generation, Industrial Control and Instrumentation, Test and Measurement Systems.
High-Speed LVDS Clock Distribution
The SY89875UMI fits high-speed LVDS clock distribution because it combines a 1:2 fanout ratio with operation up to 2 GHz and differential LVDS outputs. It can divide the incoming clock under software- or control-based configuration and then distribute the result to two destinations. Differential routing reduces susceptibility to common-mode disturbance compared with a single-ended implementation. Internal input termination helps control the source impedance, while controlled-impedance PCB routing and a continuous return path remain essential for reliable 2 GHz operation.
Recomendado
Networking and Communications Equipment
The SY89875UMI is suitable for networking and communications equipment requiring a local 2 GHz differential clock with two outputs. Its input stage accepts any differential type and is listed for CML, HSTL, LVDS, and LVPECL sources, allowing it to work with multiple high-speed clock ecosystems. The 2.5 V supply and programmable divider provide flexibility when downstream interfaces require a divided clock. Use short, matched differential traces and confirm converter jitter and fanout-device contribution during signal-integrity analysis.
Recomendado
Server and Storage Backplanes
The SY89875UMI can distribute a 2 GHz differential clock to two sections of a server, storage, or backplane subsystem. Its 1:2 architecture reduces the number of separate clock-output stages needed when two closely related loads require the same timing reference. Differential LVDS outputs are useful across circuit-board distances when trace geometry and reference planes are controlled. Before deployment, evaluate total clock jitter, power-supply noise, channel loss, return-path discontinuities, and the divider setting used for each downstream interface.
Recomendado
Programmable Clock Generation
The programmable divider integrated into the SY89875UMI makes it useful when a system must derive one or more lower-rate clocks from a common differential reference. At the same time, its 1:2 fanout supplies two outputs for distribution to separate logic groups. The device operates from 2.5 V and supports input signaling from CML, HSTL, LVDS, and LVPECL sources. Designers should consult the manufacturer configuration table to determine the supported divider ratios and the permissible input frequency for each programmed mode.
Recomendado
Industrial Control and Instrumentation
The SY89875UMI can provide synchronized timing to two processing sections in industrial control, instrumentation, and automated test systems. A differential input can reduce coupling from nearby power converters and motors, while the two fanout outputs support parallel clocking of measurement or control logic. The 2 GHz capability provides headroom for high-speed sampling and communication blocks, although the selected divider mode must maintain the required frequency and timing margin. Thermal management and power-quality checks are also necessary around the 2.5 V regulator.
Recomendado
Test and Measurement Systems
The SY89875UMI is appropriate for test and measurement systems that need to distribute a precise differential reference clock to two acquisition or synthesis channels. Programmable division allows a common source to support different operating modes, while the 2 GHz maximum frequency accommodates high-speed test paths. Differential LVDS outputs can reduce sensitivity to crosstalk when routed through a densely populated instrument chassis. Verify output amplitude, additive jitter, duty-cycle distortion, channel skew, and termination arrangement with the manufacturer's characterization data before calibration.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para SY89875UMI — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | SY89875UMG |
|---|---|---|
| Package | 16-VFQFN exposed pad (16-MLF) | 16-VFQFN exposed pad (16-MLF) |
| Brand | Microchip Technology | Microchip Technology |
| Product Type | Programmable clock divider and 1:2 fanout buffer | Same-base-design clock divider and fanout substitute |
| Supply Voltage | 2.5 V | 2.5 V |
| Maximum Frequency | 2 GHz | 2 GHz |
| Fanout Ratio | 1:2 | 1:2 |
| Input Signaling | Any differential input; CML, HSTL, LVDS, and LVPECL supported | Differential clock input |
| Output Signaling | LVDS | LVDS |
| Internal Termination | Yes | Yes |
| Divider Control | Programmable | Programmable |
Principais diferenciais
- Combines programmable division with two-output fanout (vs SY89875UMG)
- Supports several differential input standards (vs SY89875UMG)
- Uses a compact exposed-pad clock-buffer package (vs SY89875UMG)
Notas de projeto
Route each differential clock pair as a continuous, impedance-controlled pair with symmetric geometry and a continuous reference plane beneath it. Avoid vias where practical because each transition can create impedance discontinuities and degrade 2 GHz edge quality. If vias are unavoidable, use matched via structures on both conductors, provide nearby ground stitching, and verify the complete channel with an oscilloscope or channel-simulation tool. Use the manufacturer pin table when identifying differential input and LVDS output pairs.
The 16-VFQFN exposed pad must be connected to the appropriate ground reference and thermal plane with a dense via array. Maintain solder-mask and paste patterns compatible with the manufacturer's 16-MLF footprint and avoid placing high-current or noisy traces beneath the exposed pad. Review the pad-to-via geometry in the manufacturer land-pattern drawing, because an incorrect thermal-via arrangement can affect solderability, heat transfer, and return-path continuity during switching transitions.
Confirm the source impedance, internal input termination, LVDS output loading, trace length, and downstream termination before finalizing the topology. The internal termination simplifies differential input implementation, but it must be coordinated with the driver impedance and cable or PCB load. Use the manufacturer's timing and output specifications to assess duty-cycle distortion, skew, and jitter at the selected divider mode. Differential probing with matched cables is recommended to avoid introducing measurement artifacts.
Place the 2.5 V supply decoupling network close to the device and keep return-current paths short. The clock buffer's exact supply-current limit, operating range, and dissipation depend on configuration and frequency, so consult the manufacturer datasheet for the applicable values. If the 2.5 V rail is generated by a switching converter, place the regulator away from sensitive clock pairs and monitor supply ripple at the device pins with a low-inductance probe.
Informações de conformidade
Compliance attributes require confirmation from the manufacturer declaration, product page, or ordering documentation for the exact SY89875UMI configuration.