TJA1029TK - 2.2A LIN Transceiver | NXP Semiconductors
N.º da peça: TJA1029TK ✓ AtivoTJA1029TK Visão geral
A LIN transceiver is a physical-layer interface within an automotive communication network. The Local Interconnect Network is a low-cost, single-wire serial bus commonly used to connect relatively simple vehicle nodes such as sensors, switches, seat modules, and door electronics. A LIN transceiver converts the controller's transmit and receive signals into a bus-compatible waveform and reports received bus data back to the controller.
The TJA1029 supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602 communication requirements. Its stated 2.2 A bus-output capability supports the physical drive required in vehicle electrical environments, while its 20 kBd maximum signaling rate matches the communication range of LIN 2.x networks. The TXD dominant-timeout feature adds a defined protection function for the transmit-data path.
NXP identifies the TJA1029 as pin-compatible with the TJA1020, TJA1021, TJA1022, and TJA1027 families. This compatibility provides a practical basis for PCB reuse when a design is being revised, although the selected replacement must still be checked for protocol version, timeout behavior, electrical limits, and ordering suffix requirements.
Typical uses include LIN subnets containing door controls, climate-control modules, body controllers, seat electronics, lighting interfaces, and other distributed vehicle nodes. The device can serve as the physical interface in either a LIN leader or follower node because the protocol controller determines the network role independently of the transceiver.
For layout, place the TJA1029 close to the LIN connector or protected bus entry point and minimize the distance of the LIN trace. The external bus network, connector, pull-up arrangement, protection components, and vehicle-level EMC requirements must be evaluated with the complete reference design rather than as isolated component choices.
This product page consolidates the TJA1029TK identification, LIN standard coverage, known package information, pin-compatible family references, and practical replacement considerations. It also separates confirmed device facts from parameters that require confirmation in the NXP datasheet or a design-specific qualification before production release.
Alternativas drop-in para TJA1029TK — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com TJA1029TK (mesmo formato e footprint) — diferindo em Package, Pin Compatibility.
TJA1020TK/118
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TJA1021TK/118
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TJA1022TK/118
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TJA1027TK/118
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TJA1029TK Especificações
| Product Type | LIN bus transceiver |
| Bus Output Current | 2.2 A |
| Maximum Baud Rate | 20 kBd |
| LIN Compliance | LIN 2.0, LIN 2.1, LIN 2.2, and LIN 2.2A |
| Automotive Network Standard | SAE J2602 |
| Protocol Support | LIN leader and follower protocol controllers |
| Special Feature | TXD dominant timeout |
| Bus Output Driver | Optimized LIN bus signal for reduced electromagnetic emissions |
| Internal LIN Pull-Up | Present through the LIN bus output pull-up arrangement |
| Encapsulamento | 8-pin HVSON, 3 x 3 mm |
| Tipo de montagem | Surface mount |
| Pin Compatibility | Compatible with TJA1020, TJA1021, TJA1022, and TJA1027 |
Guia de Configuração de Pinos do TJA1029TK 8-pin hvson, 3 x 3 mm
Configuração de pinos para TJA1029TK (pacote 8-pin hvson, 3 x 3 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para TJA1029TK.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
TJA1029TK é adequado para 6 aplicaçãos: Vehicle Body-Control LIN Network, Door and Seat Control Modules, Climate-Control Subnet, Automotive Lighting Interface, In-Vehicle Sensor Network, Central LIN Gateway Node.
Vehicle Body-Control LIN Network
The TJA1029TK fits a body-controller LIN subnet where a protocol controller must communicate with distributed door, switch, or latch nodes. Its 2.2 A bus-output capability and 20 kBd maximum signaling rate match the physical requirements stated for LIN 2.x vehicle networks. The 8-pin 3 x 3 mm HVSON package also supports compact controller boards. In implementation, place the transceiver near the protected connector entry, retain the specified bus termination arrangement, and validate the complete branch against vehicle transient and electromagnetic-emissions requirements.
Recomendado
Door and Seat Control Modules
The TJA1029TK is appropriate for compact door and seat electronics that expose switches or motor-related nodes through a LIN bus. A LIN network reduces the wiring needed for low-bandwidth vehicle functions, while the TJA1029 provides the physical-layer interface at rates up to 20 kBd. Its LIN 2.2A and SAE J2602 positioning fits modern LIN 2.x designs, while the 2.2 A output rating provides bus-drive capability. The design must still include the required bus protection and verify wake-up, sleep, and fault-recovery behavior in the complete module.
Recomendado
Climate-Control Subnet
A climate-control module can use the TJA1029TK to connect a LIN protocol controller to distributed temperature, fan, flap, or panel nodes. LIN's single-wire topology is well suited to these lower-cost in-vehicle networks, and the TJA1029's 20 kBd limit covers the stated LIN 2.x operating range. The transceiver's optimized bus waveform is intended to minimize electromagnetic emissions, which is important where control electronics are positioned near sensitive vehicle systems. Layout the bus entry and protection network carefully, and validate timing and emissions under worst-case bus loading.
Recomendado
Automotive Lighting Interface
The TJA1029TK can form the LIN physical interface for a lighting-related control node, such as an exterior or interior lamp controller. Such nodes benefit from LIN's low-cost single-wire communications, while the transceiver supplies the bus-facing driver and receiver interface to the protocol controller. The 2.2 A output rating and support for operation up to 20 kBd align with the device's stated LIN physical-layer role. The implementation should account for the different load characteristics of lamp electronics, maintain recommended bus routing, and test standby, fault, and recovery behavior under vehicle power conditions.
Recomendado
In-Vehicle Sensor Network
The TJA1029TK can connect a simple vehicle sensor or sensing module to a LIN controller when the required information transfer rate is within 20 kBd. Suitable nodes include position, temperature, ambient, and switch-related measurements where LIN's inexpensive single-wire bus is appropriate. The device supports LIN 2.0, 2.1, 2.2, and 2.2A as well as SAE J2602, providing a broad compatibility target for LIN 2.x subnetworks. Use the manufacturer's bus application information for termination and protection, and verify wake-up and low-power behavior for modules that spend substantial time asleep.
Recomendado
Central LIN Gateway Node
A gateway or central vehicle controller can use the TJA1029TK at a LIN branch to bridge physical-layer bus traffic to a protocol controller or higher-level network interface. Its 20 kBd operation matches the stated LIN 2.x subnet limit, and the 2.2 A bus-output rating supports the physical driver required on the bus. The TXD dominant-timeout function provides an additional defined behavior in the transmit path. Gateway designs should still validate branch timing, bus termination, fault isolation, electromagnetic emissions, and recovery behavior across every attached LIN branch.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TJA1029TK — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Consider the TJA1020TK/118, TJA1021TK/118, TJA1022TK/118, or TJA1027TK/118 when their individual timeout, protocol, electrical, and qualification characteristics provide a better match. NXP identifies these devices as pin-compatible with the TJA1029, making them useful PCB-reuse candidates. However, pin compatibility does not establish feature equivalence. Before substitution, verify the package suffix, exposed-pad connection, LIN revision, dominant-timeout response, supply limits, operating-temperature range, and vehicle-program approval requirements.
Comparação com alternativas
| Parâmetro | Este produto | TJA1020TK/118 | TJA1021TK/118 | TJA1022TK/118 | TJA1027TK/118 |
|---|---|---|---|---|---|
| Package | 8-HVSON (3x3) | 8-HVSON (3x3) | 8-HVSON (3x3) | 8-HVSON (3x3) | 8-HVSON (3x3) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Pin Compatibility | TJA1020, TJA1021, TJA1022, and TJA1027 | Manufacturer-identified as pin-compatible with TJA1029 | Manufacturer-identified as pin-compatible with TJA1029 | Manufacturer-identified as pin-compatible with TJA1029 | Manufacturer-identified as pin-compatible with TJA1029 |
Principais diferenciais
- Confirmed LIN 2.2A and SAE J2602 positioning with dominant-timeout support (vs TJA1021TK/118)
- 2.2 A LIN bus-output capability (vs TJA1020TK/118)
- 20 kBd operation in a compact 3 x 3 mm HVSON package (vs TJA1022TK/118)
- Manufacturer-identified pin compatibility across four NXP family references (vs TJA1027TK/118)
Notas de projeto
Place the TJA1029TK close to the LIN connector or protected bus-entry structure and route the LIN connection as directly as practical. Preserve the termination and protection network shown in the manufacturer's application information, and keep the exposed-pad connection and land pattern consistent with the package drawing. PCB placement should also support the intended current path and thermal design rather than relying on trace geometry alone.
The TJA1029 converts controller data into an optimized LIN bus waveform intended to minimize electromagnetic emissions. Reproduction of that performance depends on the complete bus network, including connector selection, protection components, branch loading, and routing. Validate emissions and immunity in the final module because an otherwise compliant transceiver cannot compensate for an unsuitable bus harness or poor high-current return-path layout.
Do not treat a pin-compatible family member as an unconditional functional substitute. Compare the exact ordering suffix, exposed-pad connection, LIN revision, dominant-timeout behavior, bus-drive capability, supply limits, and operating-temperature requirements before releasing a replacement. The TXD dominant-timeout function is a confirmed TJA1029 feature, so changing that behavior may alter fault handling even when the PCB footprint remains unchanged.
Informações de conformidade
The device supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statuses were not confirmed in the referenced product information.