NXP Semiconductors

TJA1029TK - 2.2A LIN Transceiver | NXP Semiconductors

MPN: TJA1029TK ✓ فعال
2.2 A Id 8-pin HVSON, 3 x 3 mm Package
حداقل سفارش: 1 |

TJA1029TK نمای کلی

NXP Semiconductors TJA1029TK is a 2.2 A LIN 2.2A and SAE J2602 transceiver with a transmit-data dominant timeout function, supplied in an 8-pin HVSON package measuring 3 x 3 mm. It supports LIN bus communication at rates up to 20 kBd and connects a Local Interconnect Network master or follower protocol controller to the physical LIN bus.

A LIN transceiver is a physical-layer interface within an automotive communication network. The Local Interconnect Network is a low-cost, single-wire serial bus commonly used to connect relatively simple vehicle nodes such as sensors, switches, seat modules, and door electronics. A LIN transceiver converts the controller's transmit and receive signals into a bus-compatible waveform and reports received bus data back to the controller.

The TJA1029 supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602 communication requirements. Its stated 2.2 A bus-output capability supports the physical drive required in vehicle electrical environments, while its 20 kBd maximum signaling rate matches the communication range of LIN 2.x networks. The TXD dominant-timeout feature adds a defined protection function for the transmit-data path.

NXP identifies the TJA1029 as pin-compatible with the TJA1020, TJA1021, TJA1022, and TJA1027 families. This compatibility provides a practical basis for PCB reuse when a design is being revised, although the selected replacement must still be checked for protocol version, timeout behavior, electrical limits, and ordering suffix requirements.

Typical uses include LIN subnets containing door controls, climate-control modules, body controllers, seat electronics, lighting interfaces, and other distributed vehicle nodes. The device can serve as the physical interface in either a LIN leader or follower node because the protocol controller determines the network role independently of the transceiver.

For layout, place the TJA1029 close to the LIN connector or protected bus entry point and minimize the distance of the LIN trace. The external bus network, connector, pull-up arrangement, protection components, and vehicle-level EMC requirements must be evaluated with the complete reference design rather than as isolated component choices.

This product page consolidates the TJA1029TK identification, LIN standard coverage, known package information, pin-compatible family references, and practical replacement considerations. It also separates confirmed device facts from parameters that require confirmation in the NXP datasheet or a design-specific qualification before production release.

جایگزین‌های drop-in برای TJA1029TK — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای TJA1029TK (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Pin Compatibility.

NXP Semiconductors
Package: HVSON14 (3 x 4.5 mm) with exposed pad
Pin Compatibility: Pin compatible with TJA1020, TJA1021, TJA1027, TJA1029 (SO14 / HVSON14 footprint)
مقایسه با TJA1029TK →

TJA1020TK/118

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-HVSON (3x3)
0-pin footprint difference; timeout and LIN feature coverage differ from the TJA1029 and require datasheet confirmation

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1021TK/118

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-HVSON (3x3)
0-pin footprint difference; TXD dominant-timeout and LIN revision coverage differ from the TJA1029

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1022TK/118

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-HVSON (3x3)
0-pin footprint difference; functional timeout and electrical characteristics differ and require comparison

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1027TK/118

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-HVSON (3x3)
0-pin footprint difference; dominant-timeout implementation and LIN feature coverage require confirmation

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1029TK مشخصات

Product Type LIN bus transceiver
Bus Output Current 2.2 A
Maximum Baud Rate 20 kBd
LIN Compliance LIN 2.0, LIN 2.1, LIN 2.2, and LIN 2.2A
Automotive Network Standard SAE J2602
Protocol Support LIN leader and follower protocol controllers
Special Feature TXD dominant timeout
Bus Output Driver Optimized LIN bus signal for reduced electromagnetic emissions
Internal LIN Pull-Up Present through the LIN bus output pull-up arrangement
بسته‌بندی 8-pin HVSON, 3 x 3 mm
نوع نصب Surface mount
Pin Compatibility Compatible with TJA1020, TJA1021, TJA1022, and TJA1027

راهنمای پیکربندی پین TJA1029TK 8-pin hvson, 3 x 3 mm

پیکربندی پین برای TJA1029TK (پکیج 8-pin hvson, 3 x 3 mm). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 8-pin hvson, 3 x 3 mm برای TJA1029TK

داده پین‌آوت تفصیلی موجود نیست برای TJA1029TK.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

TJA1029TK مناسب است برای 6 کاربردs: Vehicle Body-Control LIN Network, Door and Seat Control Modules, Climate-Control Subnet, Automotive Lighting Interface, In-Vehicle Sensor Network, Central LIN Gateway Node.

🚗

Vehicle Body-Control LIN Network

The TJA1029TK fits a body-controller LIN subnet where a protocol controller must communicate with distributed door, switch, or latch nodes. Its 2.2 A bus-output capability and 20 kBd maximum signaling rate match the physical requirements stated for LIN 2.x vehicle networks. The 8-pin 3 x 3 mm HVSON package also supports compact controller boards. In implementation, place the transceiver near the protected connector entry, retain the specified bus termination arrangement, and validate the complete branch against vehicle transient and electromagnetic-emissions requirements.

🚗

Door and Seat Control Modules

The TJA1029TK is appropriate for compact door and seat electronics that expose switches or motor-related nodes through a LIN bus. A LIN network reduces the wiring needed for low-bandwidth vehicle functions, while the TJA1029 provides the physical-layer interface at rates up to 20 kBd. Its LIN 2.2A and SAE J2602 positioning fits modern LIN 2.x designs, while the 2.2 A output rating provides bus-drive capability. The design must still include the required bus protection and verify wake-up, sleep, and fault-recovery behavior in the complete module.

🌐

Climate-Control Subnet

A climate-control module can use the TJA1029TK to connect a LIN protocol controller to distributed temperature, fan, flap, or panel nodes. LIN's single-wire topology is well suited to these lower-cost in-vehicle networks, and the TJA1029's 20 kBd limit covers the stated LIN 2.x operating range. The transceiver's optimized bus waveform is intended to minimize electromagnetic emissions, which is important where control electronics are positioned near sensitive vehicle systems. Layout the bus entry and protection network carefully, and validate timing and emissions under worst-case bus loading.

💡

Automotive Lighting Interface

The TJA1029TK can form the LIN physical interface for a lighting-related control node, such as an exterior or interior lamp controller. Such nodes benefit from LIN's low-cost single-wire communications, while the transceiver supplies the bus-facing driver and receiver interface to the protocol controller. The 2.2 A output rating and support for operation up to 20 kBd align with the device's stated LIN physical-layer role. The implementation should account for the different load characteristics of lamp electronics, maintain recommended bus routing, and test standby, fault, and recovery behavior under vehicle power conditions.

🧩

In-Vehicle Sensor Network

The TJA1029TK can connect a simple vehicle sensor or sensing module to a LIN controller when the required information transfer rate is within 20 kBd. Suitable nodes include position, temperature, ambient, and switch-related measurements where LIN's inexpensive single-wire bus is appropriate. The device supports LIN 2.0, 2.1, 2.2, and 2.2A as well as SAE J2602, providing a broad compatibility target for LIN 2.x subnetworks. Use the manufacturer's bus application information for termination and protection, and verify wake-up and low-power behavior for modules that spend substantial time asleep.

🔧

Central LIN Gateway Node

A gateway or central vehicle controller can use the TJA1029TK at a LIN branch to bridge physical-layer bus traffic to a protocol controller or higher-level network interface. Its 20 kBd operation matches the stated LIN 2.x subnet limit, and the 2.2 A bus-output rating supports the physical driver required on the bus. The TXD dominant-timeout function provides an additional defined behavior in the transmit path. Gateway designs should still validate branch timing, bus termination, fault isolation, electromagnetic emissions, and recovery behavior across every attached LIN branch.

خلاصه محصولات پیشنهادی

TJA1021TK/118 Pin-compatible NXP LIN transceiver family alternative استفاده‌شده در: Vehicle Body-Control LIN Network, Climate-Control Subnet, In-Vehicle Sensor Network TJA1027TK/118 Pin-compatible NXP LIN transceiver family alternative استفاده‌شده در: Vehicle Body-Control LIN Network, Automotive Lighting Interface, Central LIN Gateway Node TJA1020TK/118 Pin-compatible NXP LIN transceiver family alternative استفاده‌شده در: Door and Seat Control Modules, Automotive Lighting Interface, Central LIN Gateway Node TJA1022TK/118 Pin-compatible NXP LIN transceiver family alternative استفاده‌شده در: Door and Seat Control Modules, Climate-Control Subnet, In-Vehicle Sensor Network
What is the NXP TJA1029TK?
The NXP TJA1029TK is a 2.2 A LIN physical-layer transceiver for LIN bus communication at rates up to 20 kBd. According to the NXP manufacturer datasheet, it is intended for in-vehicle subnetworks and interfaces a LIN master or follower protocol controller to the physical bus. The device is supplied in an 8-pin HVSON package measuring 3 x 3 mm and includes a TXD dominant-timeout function.
What LIN standards does the TJA1029TK support?
The TJA1029TK supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602. The NXP manufacturer datasheet identifies these standards as the applicable network requirements for the transceiver. Because the product description specifically identifies LIN 2.2A, a design requiring another LIN revision or a different automotive network specification should confirm compatibility before approval.
What is the maximum LIN baud rate of the TJA1029TK?
The TJA1029TK supports LIN signaling at up to 20 kBd. The NXP manufacturer datasheet describes the transceiver as intended for in-vehicle subnetworks using baud rates up to 20 kBd, consistent with LIN 2.x physical-layer operation. Configuration timing in the LIN protocol controller must also match the selected bus baud rate, and the complete network should be checked for timing margin.
What package does the TJA1029TK use?
The TJA1029TK uses an 8-pin HVSON package with a 3 x 3 mm body size. The exact package designation is shown in the NXP manufacturer datasheet and the distributor product listing. Any replacement must preserve the land pattern, exposed-pad requirements, pin numbering, and thermal design; a device described only as an 8-pin transceiver may not be a mechanical drop-in.
What can replace the TJA1029TK on the same PCB?
The TJA1029TK can be replaced directly in the NXP pin-compatible family identified as TJA1020, TJA1021, TJA1022, or TJA1027 when the correct package suffix and electrical requirements are retained. The NXP manufacturer datasheet explicitly describes this pin compatibility. Confirm timeout behavior, LIN revision, supply limits, bus-drive capability, and exposed-pad layout for the exact replacement ordering code.
What is the difference between the TJA1029TK and the TJA1020?
The TJA1029TK and TJA1020 belong to the same NXP LIN-transceiver family and are identified as pin-compatible by the manufacturer. Their feature sets and ordering variants still require comparison against the exact part numbers, especially TXD dominant-timeout behavior, LIN protocol revision, electrical limits, and package suffix. The TJA1029TK is specifically identified as a LIN 2.2A and SAE J2602 device with TXD dominant timeout.
When should I choose the TJA1029TK instead of another LIN transceiver?
Choose the TJA1029TK when the design needs an NXP LIN transceiver with 20 kBd operation, LIN 2.2A and SAE J2602 coverage, a 2.2 A bus-output rating, and a TXD dominant-timeout function in an 8-pin HVSON footprint. Select another family member when its timeout, protocol coverage, electrical limits, or qualification better matches the vehicle program. Pin compatibility alone does not replace a complete functional review.
Is the TJA1029TK suitable for an automotive LIN subnet?
The TJA1029TK is specifically intended for in-vehicle LIN subnetworks and supports LIN 2.0 through LIN 2.2A together with SAE J2602. Its 20 kBd capability and 2.2 A bus-output rating suit LIN physical-layer networks. Vehicle-level suitability still depends on the exact electrical limits, environmental qualification, transient protection, EMC validation, and manufacturer change-control requirements for the production program.
Where can I download the TJA1029TK datasheet PDF?
Download the TJA1029TK datasheet PDF from the official NXP document link associated with this product page: https://www.nxp.com/docs/en/data-sheet/TJA1029.pdf. The NXP manufacturer datasheet is the primary document for the complete pin description, electrical limits, timing values, package drawing, application information, and revision history. Use the pin-description table there when assigning PCB tracks.
Where can I find the TJA1029TK pinout?
The TJA1029TK pinout is defined in the NXP manufacturer datasheet and its package drawing for the 8-pin HVSON device. Use the pin-description table to identify supply, ground, transmit, receive, LIN, enable, and exposed-pad functions before routing the PCB. The exposed pad may be electrically significant and thermally important, so its datasheet connection and land-pattern requirements must be followed exactly.
What are the key specifications of the TJA1029TK that engineers should know?
The key TJA1029TK specifications are a 2.2 A LIN bus-output rating, operation up to 20 kBd, LIN 2.0/2.1/2.2/2.2A and SAE J2602 coverage, a TXD dominant-timeout function, and an 8-pin 3 x 3 mm HVSON package. The NXP manufacturer datasheet also identifies pin compatibility with TJA1020, TJA1021, TJA1022, and TJA1027, making those devices important candidates for PCB-level engineering review.
Is the TJA1029TK the same as the TJA1021TK?
No, the TJA1029TK is not necessarily functionally identical to the TJA1021TK even though NXP identifies the devices as pin-compatible. The TJA1029TK is identified with a TXD dominant-timeout function and LIN 2.2A and SAE J2602 support. Before treating it as a replacement, compare the exact timeout implementation, LIN revision, electrical characteristics, qualification, and exposed-pad requirements in the manufacturer datasheets.
How should the LIN bus trace be routed around the TJA1029TK?
Place the TJA1029TK close to the LIN connector or protected bus-entry structure and keep the LIN trace as short and direct as practical. Maintain the bus pull-up and protection arrangements specified by the manufacturer application information, and review the complete reference design for surge, ESD, and vehicle transient requirements. PCB return-path geometry and connector placement also influence electromagnetic-emissions performance.
Where can I buy the TJA1029TK?
Use the Request a Quote form on this page to request the TJA1029TK, current commercial availability, order quantity, and lead time. The exact ordering code and package suffix should be confirmed during the quotation because the product is also listed under an ordering notation that includes a tape-and-reel suffix. The form provides the appropriate request channel without embedding a potentially stale commercial quote in technical content.
What is the price and lead time of the TJA1029TK?
Use the Request a Quote form on this page for the current TJA1029TK price, stock position, minimum order quantity, and production lead time. Commercial terms can change with order quantity, date, and supply status, so they should be confirmed at the time of quotation. Technical selection can proceed independently using the documented 2.2 A rating, 20 kBd operation, LIN standard coverage, and package information.
Can a TJA1027TK replace the TJA1029TK without a PCB change?
A correctly packaged TJA1027TK is a candidate for a PCB-compatible redesign because the NXP manufacturer datasheet lists the TJA1027 among devices pin-compatible with the TJA1029. However, pin compatibility does not guarantee identical timeout behavior or electrical performance. Confirm the package suffix, exposed-pad layout, LIN revision, bus-drive specifications, timeout response, qualification, and application requirements before releasing the substitution.

داده‌های مرجع مهندسی برای TJA1029TK — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the TJA1029TK when the design needs an NXP LIN transceiver with a confirmed 2.2 A bus-output rating, operation up to 20 kBd, LIN 2.2A and SAE J2602 coverage, and a TXD dominant-timeout function in an 8-pin 3 x 3 mm HVSON package. It is particularly suitable for compact vehicle body, door, seat, climate, lighting, and sensor modules using LIN 2.x physical-layer networks.

Consider the TJA1020TK/118, TJA1021TK/118, TJA1022TK/118, or TJA1027TK/118 when their individual timeout, protocol, electrical, and qualification characteristics provide a better match. NXP identifies these devices as pin-compatible with the TJA1029, making them useful PCB-reuse candidates. However, pin compatibility does not establish feature equivalence. Before substitution, verify the package suffix, exposed-pad connection, LIN revision, dominant-timeout response, supply limits, operating-temperature range, and vehicle-program approval requirements.

مقایسه با جایگزین‌ها

پارامتر این محصول TJA1020TK/118 TJA1021TK/118 TJA1022TK/118 TJA1027TK/118
Package 8-HVSON (3x3) 8-HVSON (3x3) 8-HVSON (3x3) 8-HVSON (3x3) 8-HVSON (3x3)
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Pin Compatibility TJA1020, TJA1021, TJA1022, and TJA1027 Manufacturer-identified as pin-compatible with TJA1029 Manufacturer-identified as pin-compatible with TJA1029 Manufacturer-identified as pin-compatible with TJA1029 Manufacturer-identified as pin-compatible with TJA1029

تفاوت‌های کلیدی

  • Confirmed LIN 2.2A and SAE J2602 positioning with dominant-timeout support (در مقابلTJA1021TK/118)
  • 2.2 A LIN bus-output capability (در مقابلTJA1020TK/118)
  • 20 kBd operation in a compact 3 x 3 mm HVSON package (در مقابلTJA1022TK/118)
  • Manufacturer-identified pin compatibility across four NXP family references (در مقابلTJA1027TK/118)

یادداشت‌های طراحی

Place the TJA1029TK close to the LIN connector or protected bus-entry structure and route the LIN connection as directly as practical. Preserve the termination and protection network shown in the manufacturer's application information, and keep the exposed-pad connection and land pattern consistent with the package drawing. PCB placement should also support the intended current path and thermal design rather than relying on trace geometry alone.

The TJA1029 converts controller data into an optimized LIN bus waveform intended to minimize electromagnetic emissions. Reproduction of that performance depends on the complete bus network, including connector selection, protection components, branch loading, and routing. Validate emissions and immunity in the final module because an otherwise compliant transceiver cannot compensate for an unsuitable bus harness or poor high-current return-path layout.

Do not treat a pin-compatible family member as an unconditional functional substitute. Compare the exact ordering suffix, exposed-pad connection, LIN revision, dominant-timeout behavior, bus-drive capability, supply limits, and operating-temperature requirements before releasing a replacement. The TXD dominant-timeout function is a confirmed TJA1029 feature, so changing that behavior may alter fault handling even when the PCB footprint remains unchanged.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The device supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statuses were not confirmed in the referenced product information.

تاریخ تأیید داده‌ها: 2026-11-09 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

nxp tja1029tk TJA1029TK datasheet TJA1029TK datasheet pdf TJA1029TK pinout TJA1029TK equivalent TJA1029TK replacement TJA1029TK cross reference TJA1029TK vs TJA1021 TJA1029TK footprint TJA1029TK application circuit TJA1029TK price TJA1029TK stock TJA1029TK 20 kBd TJA1029TK LIN 2.2A 8-HVSON LIN transceiver pinout

قطعات و اصطلاحات مرتبط

NXP Semiconductors TJA1029TK TJA1020 TJA1021 TJA1022 TJA1027 LIN transceiver Local Interconnect Network LIN bus physical-layer interface LIN leader LIN follower protocol controller LIN 2.0 LIN 2.1 LIN 2.2 LIN 2.2A SAE J2602 TXD dominant timeout 8-pin HVSON 3 x 3 mm package surface-mount package automotive subnetwork 2.2 A bus output 20 kBd
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ