TLV2450ID - 23µA, 220kHz RRIO Op Amp | Texas Instruments
N.º da peça: TLV2450ID ✓ AtivoTLV2450ID Visão geral
An operational amplifier is a voltage-gain circuit used to amplify small signals in instrumentation, control, sensor, and analog signal-processing systems. The TLV2450ID belongs to the operational-amplifier hierarchy, where rail-to-rail input and output capability allows the signal to approach the supply rails. This is particularly useful in battery-powered equipment operating from low-voltage supplies, where usable input and output range is limited.
The TLV2450ID combines 220 kHz gain-bandwidth product with 23 µA typical quiescent current. Its rail-to-rail input stage accepts signals near either supply rail, while the rail-to-rail output stage can drive loads toward the output limits. The manufacturer also specifies 20 µV typical input offset voltage and ±10 mA output-drive capability. A shutdown pin provides a direct way to control active power consumption in portable and intermittently operated systems.
The TLV2450 is designed as a general-purpose amplifier for low-voltage analog systems. Its 220 kHz bandwidth supports moderate-frequency signal paths without requiring a higher-speed amplifier. Typical operating current of 23 µA is especially valuable in sensor nodes, portable instruments, and monitoring systems where amplifier power can dominate standby energy. The shutdown function can further reduce consumption when acquisition is intermittent.
Typical applications include low-power sensor conditioning, portable measurement equipment, industrial monitoring, current-loop receivers, and buffered analog signal paths. In these systems, the amplifier can process transducer outputs close to ground or the positive rail while operating from a low-voltage supply. Care should be taken to preserve output swing margin and stable operation under the intended load and feedback configuration.
For PCB design, place input and feedback components close to the amplifier pins, route sensitive input traces away from switching nodes, and use a stable feedback network appropriate for the required gain and bandwidth. Verify output drive, capacitive-load behavior, and shutdown logic against the circuit timing before releasing the design.
This page combines the TLV2450ID operating characteristics with package guidance, application-focused design advice, and same-footprint alternatives for engineers evaluating a low-power rail-to-rail operational-amplifier design.
Alternativas drop-in para TLV2450ID — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com TLV2450ID (mesmo formato e footprint) — diferindo em Amplifier Type, Input Common-Mode Range, Output Swing.
TLV2450IDG4
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TLV2450AIDG4
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TLV2450AID
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TLV2451ID
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →TLV2450ID Classificações máximas e características elétricas
| Amplifier Type | Single general-purpose operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 220 kHz |
| Supply Current per Channel | 23 µA typical |
| Maximum Supply Voltage | 6 V |
| Input Common-Mode Range | Rail-to-rail input |
| Output Swing | Rail-to-rail output |
| Input Offset Voltage | 20 µV typical |
| Output Drive Capability | ±10 mA |
| Shutdown Control | Yes |
| Encapsulamento | 8-pin SOIC |
| Contagem de pinos | 8 pins |
| Tipo de montagem | Surface mount |
| Status RoHS | Compliant |
| Lead-Free Status | Yes |
Guia de Configuração de Pinos do TLV2450ID 8-pin soic
Configuração de pinos para TLV2450ID (pacote 8-pin soic). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para TLV2450ID.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
TLV2450ID é adequado para 6 aplicaçãos: Low-Power Sensor Signal Conditioning, Portable Measurement Instrumentation, Industrial Process Monitoring, Battery-Powered Data Acquisition, Current-Loop Signal Conditioning, Low-Power Audio and Control Buffers.
Low-Power Sensor Signal Conditioning
The TLV2450ID is well suited to conditioning outputs from low-power sensors because its rail-to-rail input stage accepts signals near the supply rails and its typical supply current is only 23 µA per channel. Place the amplifier directly after the sensor and use a closed-loop filter or gain stage that keeps the signal bandwidth below the device’s 220 kHz gain-bandwidth product. This configuration reduces board area and avoids introducing a high-current amplifier into a compact sensing node. The shutdown input can also disable the amplifier between measurement events.
Recomendado
Portable Measurement Instrumentation
Portable meters and analyzers benefit from the TLV2450ID because it combines 23 µA typical supply current with a 220 kHz gain-bandwidth product and rail-to-rail input/output capability. It can amplify a bridge, thermistor, or low-level sensor signal without requiring a split supply, which simplifies power conversion and increases usable signal range. Keep the feedback network close to the device and validate the output settling at the selected gain before using it in precision measurements.
Recomendado
Industrial Process Monitoring
The TLV2450ID can buffer or amplify slow process-control signals in industrial monitoring equipment where low quiescent current helps limit heat in distributed sensing nodes. Rail-to-rail inputs support sensor outputs near ground, while the 6 V maximum supply rating accommodates low-voltage industrial rails. Protection components and filtering should be placed ahead of the input, while the amplifier output should be checked for the required load current and settling behavior.
Recomendado
Battery-Powered Data Acquisition
For battery-powered data acquisition, the TLV2450ID provides a practical balance of low power and moderate bandwidth. Its 23 µA typical supply current reduces the continuous load from signal conditioning, while the 220 kHz gain-bandwidth product supports slow sensor and control signals. Asserting shutdown during idle periods can reduce consumption further. Designers should calculate the average current from the measurement duty cycle and include leakage from surrounding sensors and protection components.
Recomendado
Current-Loop Signal Conditioning
The TLV2450ID is appropriate for buffering and conditioning current-loop signals in industrial and instrumentation systems because it provides rail-to-rail input and output stages at low supply current. The input can operate close to ground, which is useful when measuring the small voltage across a current-sense element. Select a feedback resistor pair that establishes the required loop voltage, verify input offset and bias behavior, and provide filtering that does not compromise loop stability.
Recomendado
Low-Power Audio and Control Buffers
The TLV2450ID can serve as a low-level buffer or control amplifier where full audio bandwidth is unnecessary. Its rail-to-rail output improves signal swing in low-voltage systems, while 23 µA typical supply current is useful for always-on control electronics. The ±10 mA output-drive rating supports modest loads, but designers should confirm capacitive-load behavior and avoid driving long cables directly. Feedback compensation must be selected for the actual source and load impedances.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TLV2450ID — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TLV2450IDG4 | TLV2450AIDG4 | TLV2450AID | TLV2451ID |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Gain-Bandwidth Product | 220 kHz | 220 kHz | 220 kHz | 220 kHz | 220 kHz |
| Supply Current per Channel | 23 µA typical | 23 µA typical | 23 µA typical | 23 µA typical | 23 µA typical |
| Maximum Supply Voltage | 6 V | 6 V | 6 V | 6 V | 6 V |
| Rail-to-Rail Input and Output | Yes | Yes | Yes | Yes | Yes |
| Shutdown Control | Yes | Yes | Yes | Yes | Yes, active behavior differs by family option |
Principais diferenciais
- Low operating current supports portable analog conditioning (vs TLV2450IDG4)
- Rail-to-rail operation maximizes low-voltage signal range (vs TLV2450AIDG4)
- Shutdown support enables duty-cycled low-power operation (vs TLV2451ID)
Notas de projeto
The TLV2450ID consumes 23 µA per channel under typical operating conditions. For a duty-cycled design, calculate average supply current from the active current, shutdown current, acquisition duration, and idle interval. Use the shutdown pin to disable the amplifier when it is not needed, but include control-pin leakage and the current drawn by the sensor, voltage reference, and supporting circuitry in the complete power budget.
Place the amplifier input, feedback resistors, and output components close to the corresponding pins. Keep the noninverting and inverting traces short, use a continuous ground reference, and route them away from switching-converter nodes. If the input source has high source impedance, add filtering close to the amplifier rather than at the remote sensor, where electrostatic discharge and leakage could affect the signal.
The 220 kHz gain-bandwidth product limits useful closed-loop bandwidth according to the selected noise-gain and phase-margin requirements. Before finalizing a gain stage, evaluate settling, capacitive loading, and stability rather than relying only on nominal bandwidth. Place optional output isolation or compensation networks close to the output pin and verify them across the complete supply-voltage range.
Do not assume that every TLV245x-family orderable MPN has identical shutdown polarity or qualification limits. Confirm the active shutdown level, pin configuration, temperature range, and absolute maximum ratings in the manufacturer datasheet before replacing TLV2450ID. Also account for output swing limits under load; rail-to-rail operation does not guarantee that the output can reach either rail exactly under every load condition.
Informações de conformidade
RoHS-compliant and lead-free construction are identified in the component listing. No automotive qualification, REACH declaration, halogen-free declaration, or conflict-minerals statement is established for TLV2450ID.