Texas Instruments

TLV2450ID - 23µA, 220kHz RRIO Op Amp | Texas Instruments

Référence : TLV2450ID ✓ Actif
23 µA typical Vdss 8-pin SOIC Package
MOQ : 1 |

TLV2450ID Présentation

The Texas Instruments TLV2450ID is a single, low-power rail-to-rail input/output operational amplifier with a 220 kHz gain-bandwidth product, 23 µA supply current per channel, and a maximum supply voltage of 6 V. The device is offered in an 8-pin SOIC package and includes a shutdown function for reducing power consumption when the amplifier is not needed.

An operational amplifier is a voltage-gain circuit used to amplify small signals in instrumentation, control, sensor, and analog signal-processing systems. The TLV2450ID belongs to the operational-amplifier hierarchy, where rail-to-rail input and output capability allows the signal to approach the supply rails. This is particularly useful in battery-powered equipment operating from low-voltage supplies, where usable input and output range is limited.

The TLV2450ID combines 220 kHz gain-bandwidth product with 23 µA typical quiescent current. Its rail-to-rail input stage accepts signals near either supply rail, while the rail-to-rail output stage can drive loads toward the output limits. The manufacturer also specifies 20 µV typical input offset voltage and ±10 mA output-drive capability. A shutdown pin provides a direct way to control active power consumption in portable and intermittently operated systems.

The TLV2450 is designed as a general-purpose amplifier for low-voltage analog systems. Its 220 kHz bandwidth supports moderate-frequency signal paths without requiring a higher-speed amplifier. Typical operating current of 23 µA is especially valuable in sensor nodes, portable instruments, and monitoring systems where amplifier power can dominate standby energy. The shutdown function can further reduce consumption when acquisition is intermittent.

Typical applications include low-power sensor conditioning, portable measurement equipment, industrial monitoring, current-loop receivers, and buffered analog signal paths. In these systems, the amplifier can process transducer outputs close to ground or the positive rail while operating from a low-voltage supply. Care should be taken to preserve output swing margin and stable operation under the intended load and feedback configuration.

For PCB design, place input and feedback components close to the amplifier pins, route sensitive input traces away from switching nodes, and use a stable feedback network appropriate for the required gain and bandwidth. Verify output drive, capacitive-load behavior, and shutdown logic against the circuit timing before releasing the design.

This page combines the TLV2450ID operating characteristics with package guidance, application-focused design advice, and same-footprint alternatives for engineers evaluating a low-power rail-to-rail operational-amplifier design.

Alternatives de remplacement direct pour TLV2450ID — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec TLV2450ID (même facteur de forme et même empreinte) — différant par Amplifier Type, Input Common-Mode Range, Output Swing.

Texas Instruments
Amplifier Type: Single operational amplifier
Input Common-Mode Range: Rail-to-rail
Output Swing: Rail-to-rail
Comparer avec TLV2450ID →

TLV2450IDG4

✅ Remplacement direct
📦 8-SOIC
Gain-bandwidth product remains 220 kHz and supply current remains 23 µA per channel, a 0% change in the headline ratings; the G4 ordering suffix distinguishes the packaged option.

📋 Alternative de référence (hors catalogue)

TLV2450AIDG4

✅ Remplacement direct
📦 8-SOIC
The family comparison identifies 220 kHz gain-bandwidth product and 23 µA supply current per channel, matching the headline ratings within 0%; verify the A-version ordering limits and qualification details.

📋 Alternative de référence (hors catalogue)

TLV2450AID

✅ Remplacement direct ⚠️ Spécifications non vérifiées
📦 8-SOIC
The same-family A designation retains the 220 kHz and 23 µA headline performance within 0%, while temperature, qualification, or lifecycle limits must be confirmed for the specific orderable MPN.

📋 Alternative de référence (hors catalogue)

TLV2451ID

✅ Remplacement direct ⚠️ Spécifications non vérifiées
Texas Instruments
📦 8-SOIC
Single operational amplifier · 6 V · 220 kHz · 23 µA per channel · Rail-to-rail · Rail-to-rail · 8-pin SOIC · Surface mount

Contactez-nous pour le prix

Voir la fiche technique →

TLV2450ID Valeurs maximales et caractéristiques électriques

Amplifier Type Single general-purpose operational amplifier
Number of Channels 1 channel
Gain-Bandwidth Product 220 kHz
Supply Current per Channel 23 µA typical
Maximum Supply Voltage 6 V
Input Common-Mode Range Rail-to-rail input
Output Swing Rail-to-rail output
Input Offset Voltage 20 µV typical
Output Drive Capability ±10 mA
Shutdown Control Yes
Boîtier 8-pin SOIC
Nombre de broches 8 pins
Type de montage Surface mount
Statut RoHS Compliant
Lead-Free Status Yes

Guide de configuration des broches du TLV2450ID 8-pin soic

Configuration des broches du TLV2450ID (boîtier 8-pin soic). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.

Schéma de brochage du boîtier 8-pin soic pour le TLV2450ID

Aucune donnée de brochage détaillée disponible pour TLV2450ID.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

TLV2450ID convient pour 6 applications: Low-Power Sensor Signal Conditioning, Portable Measurement Instrumentation, Industrial Process Monitoring, Battery-Powered Data Acquisition, Current-Loop Signal Conditioning, Low-Power Audio and Control Buffers.

🧩

Low-Power Sensor Signal Conditioning

The TLV2450ID is well suited to conditioning outputs from low-power sensors because its rail-to-rail input stage accepts signals near the supply rails and its typical supply current is only 23 µA per channel. Place the amplifier directly after the sensor and use a closed-loop filter or gain stage that keeps the signal bandwidth below the device’s 220 kHz gain-bandwidth product. This configuration reduces board area and avoids introducing a high-current amplifier into a compact sensing node. The shutdown input can also disable the amplifier between measurement events.

📱

Portable Measurement Instrumentation

Portable meters and analyzers benefit from the TLV2450ID because it combines 23 µA typical supply current with a 220 kHz gain-bandwidth product and rail-to-rail input/output capability. It can amplify a bridge, thermistor, or low-level sensor signal without requiring a split supply, which simplifies power conversion and increases usable signal range. Keep the feedback network close to the device and validate the output settling at the selected gain before using it in precision measurements.

🏭

Industrial Process Monitoring

The TLV2450ID can buffer or amplify slow process-control signals in industrial monitoring equipment where low quiescent current helps limit heat in distributed sensing nodes. Rail-to-rail inputs support sensor outputs near ground, while the 6 V maximum supply rating accommodates low-voltage industrial rails. Protection components and filtering should be placed ahead of the input, while the amplifier output should be checked for the required load current and settling behavior.

⚡

Battery-Powered Data Acquisition

For battery-powered data acquisition, the TLV2450ID provides a practical balance of low power and moderate bandwidth. Its 23 µA typical supply current reduces the continuous load from signal conditioning, while the 220 kHz gain-bandwidth product supports slow sensor and control signals. Asserting shutdown during idle periods can reduce consumption further. Designers should calculate the average current from the measurement duty cycle and include leakage from surrounding sensors and protection components.

🔧

Current-Loop Signal Conditioning

The TLV2450ID is appropriate for buffering and conditioning current-loop signals in industrial and instrumentation systems because it provides rail-to-rail input and output stages at low supply current. The input can operate close to ground, which is useful when measuring the small voltage across a current-sense element. Select a feedback resistor pair that establishes the required loop voltage, verify input offset and bias behavior, and provide filtering that does not compromise loop stability.

🎧

Low-Power Audio and Control Buffers

The TLV2450ID can serve as a low-level buffer or control amplifier where full audio bandwidth is unnecessary. Its rail-to-rail output improves signal swing in low-voltage systems, while 23 µA typical supply current is useful for always-on control electronics. The ±10 mA output-drive rating supports modest loads, but designers should confirm capacitive-load behavior and avoid driving long cables directly. Feedback compensation must be selected for the actual source and load impedances.

Récapitulatif des produits recommandés

TLV2450IDG4 Same-family 8-SOIC option for sensor conditioning Utilisé dans : Low-Power Sensor Signal Conditioning, Industrial Process Monitoring, Current-Loop Signal Conditioning TLV2450AIDG4 Same-family 8-SOIC option for comparison Utilisé dans : Low-Power Sensor Signal Conditioning, Industrial Process Monitoring, Current-Loop Signal Conditioning TLV2450AID Same-family low-power amplifier option Utilisé dans : Portable Measurement Instrumentation, Battery-Powered Data Acquisition, Low-Power Audio and Control Buffers TLV2451ID Texas Instruments Utilisé dans : Portable Measurement Instrumentation, Battery-Powered Data Acquisition, Low-Power Audio and Control Buffers
What are the key specifications of TLV2450ID that engineers should know?
The TLV2450ID is a single operational amplifier with 220 kHz gain-bandwidth product, 23 µA typical supply current per channel, and a maximum supply voltage of 6 V. It provides rail-to-rail input and output operation, 20 µV typical input offset voltage, and a shutdown function. According to the Texas Instruments TLV2450 datasheet, these characteristics position it as a low-power, general-purpose amplifier for low-voltage analog systems.
What is the operating voltage of TLV2450ID?
The TLV2450ID supports operation with a maximum supply voltage of 6 V. Because it is a rail-to-rail input/output amplifier, its input and output stages are intended to operate near the supply limits, although practical output swing still depends on load current and output voltage. The Texas Instruments TLV2450 datasheet should be consulted for the complete recommended operating conditions and limit values.
What is the gain-bandwidth product of TLV2450ID?
The TLV2450ID has a gain-bandwidth product of 220 kHz. This provides useful bandwidth for low-frequency sensor signals, analog filtering, buffering, and general-purpose signal conditioning. According to the Texas Instruments TLV2450 datasheet, the device combines this bandwidth with 23 µA typical supply current, making it suitable for compact, low-power analog designs that do not require high-speed amplification.
Where can I download the TLV2450ID datasheet PDF?
The official TLV2450 product page on Texas Instruments provides the manufacturer documentation for the TLV2450ID and its related ordering options. Use that page to obtain the current datasheet and supporting information. The TLV2450ID is also identified as an 8-SOIC device with shutdown, 220 kHz gain-bandwidth product, and 23 µA typical supply current per channel.
Where can I find the TLV2450ID pinout?
The TLV2450ID pin assignment is published in the pin-configuration section of the Texas Instruments TLV2450 datasheet. The device uses an 8-pin SOIC package and includes pins for its operational-amplifier function, power supply, and shutdown control. Use the manufacturer pin-description table when assigning PCB tracks because the operational-amplifier input and output positions must match the package orientation exactly.
What can replace the TLV2450ID?
The TLV2450IDG4 and TLV2450AIDG4 are same-family Texas Instruments options associated with the TLV2450 device family and use the 8-SOIC format. TLV2451ID can also be considered when its shutdown behavior and electrical limits satisfy the circuit requirements. Because an operational-amplifier replacement must match pinout, supply range, bandwidth, offset, and shutdown polarity, verify the manufacturer datasheet before approving any substitution.
Is TLV2450ID the same as TLV2450AIDG4?
The TLV2450ID and TLV2450AIDG4 belong to the same Texas Instruments TLV2450 family and are associated with the 8-SOIC format, but the A-version ordering designation can identify a different qualification or revision family. They should not be treated as automatically identical without checking the manufacturer ordering table, pin configuration, temperature range, and full electrical specifications. The shutdown logic must also match the system requirement.
TLV2450ID vs TLV2451ID - which is better for a low-power design?
Choose TLV2450ID when its specified shutdown behavior and electrical limits match the design exactly; choose TLV2451ID when its shutdown characteristics provide a functional benefit. Both devices belong to the low-power, 220 kHz operational-amplifier family, but a shutdown-polarity difference can change board-level control logic. Confirm the active logic, timing, and pin assignments in the Texas Instruments datasheet before treating either part as interchangeable.
When should I choose TLV2450ID over a higher-speed operational amplifier?
Choose TLV2450ID when the signal bandwidth is modest and supply current is more important than conversion speed. Its 220 kHz gain-bandwidth product and 23 µA typical supply current are well matched to low-frequency sensing, buffering, and portable measurement systems. A higher-speed amplifier may be preferable for wideband signals, faster settling, or driving demanding loads, but it will generally require additional operating power.
Is TLV2450ID suitable for battery-powered sensor conditioning?
The TLV2450ID is suitable for many battery-powered sensor-conditioning circuits because it combines rail-to-rail input/output operation with 23 µA typical supply current per channel. The shutdown function can reduce power use when measurements are not continuously required. Confirm that the sensor signal remains within the input common-mode range and that the selected gain, load, and supply voltage satisfy the application requirements.
How much power does the TLV2450ID consume?
The TLV2450ID consumes approximately 23 µA per channel under the manufacturer’s stated typical operating conditions. Actual supply current depends on supply voltage, output state, operating mode, and whether the shutdown function is asserted. For a first-order power estimate, multiply the selected supply voltage by the expected operating current, then compare the result with the battery's available energy and the system's duty cycle.
Where can I buy TLV2450ID online?
Use the Request a Quote form on this page to request TLV2450ID pricing, availability, and lead time. The form connects the request directly with XAIPART rather than requiring a search across multiple sales channels. For design confirmation, specify the 8-pin SOIC package, required quantity, and whether reels, tubes, or another shipment format is needed.
What is the price of TLV2450ID?
Current TLV2450ID pricing depends on quantity, package format, and market conditions. Submit a request through the Request a Quote form on this page to obtain a current quotation for the exact quantity and shipment configuration. The form is the appropriate route for commercial confirmation because component pricing and inventory can change independently of the technical specifications.
What is the lead time for TLV2450ID?
The current lead time depends on order quantity, packaging format, and supply status. Use the Request a Quote form on this page to provide those details and request a current lead-time commitment. For new production designs, request a written supply plan for the expected annual volume and consider qualifying an alternate source before the schedule becomes constrained.
Is TLV2450ID in stock?
Current TLV2450ID inventory changes with order activity and packaging requirements. Use the Request a Quote form on this page to request a stock check and quotation for the quantity you need. Include the desired package, tape-and-reel or tube preference, target date, and production forecast so the response reflects the actual assembly plan.
What is the best alternative-brand equivalent for TLV2450ID?
No alternative-brand drop-in equivalent is established by the manufacturer information for the TLV2450ID, so a specific cross-brand substitution should not be assumed. A candidate must use the same 8-SOIC footprint and preserve pin functions, shutdown polarity, supply range, 220 kHz-class bandwidth, output-drive capability, and low-current operation. Use Texas Instruments’ cross-reference search or compare candidate manufacturer datasheets before introducing a second source.

Données de référence d'ingénierie pour TLV2450ID — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose TLV2450ID for low-voltage sensor conditioning, portable measurement, and general-purpose analog buffering where 220 kHz bandwidth, 23 µA typical supply current, rail-to-rail input/output operation, and shutdown control are important. TLV2450IDG4 is the closest same-family ordering option when its package, temperature, and qualification details match the design. Consider TLV2450AIDG4 only after checking the A-version ordering and qualification limits. TLV2450AID can be evaluated within the same family, but its exact limits must be confirmed. TLV2451ID may suit a design needing different shutdown behavior, although that control difference can require a PCB or firmware change. No cross-brand drop-in part is established here because functional equivalence alone is insufficient; any new-source candidate must preserve the 8-SOIC pinout, shutdown polarity, 6 V maximum supply rating, 220 kHz-class bandwidth, and low-power operating requirements.

Comparaison avec les alternatives

Paramètre Ce produit TLV2450IDG4 TLV2450AIDG4 TLV2450AID TLV2451ID
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-SOIC 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same
Number of Channels 1 channel 1 channel 1 channel 1 channel 1 channel
Gain-Bandwidth Product 220 kHz 220 kHz 220 kHz 220 kHz 220 kHz
Supply Current per Channel 23 µA typical 23 µA typical 23 µA typical 23 µA typical 23 µA typical
Maximum Supply Voltage 6 V 6 V 6 V 6 V 6 V
Rail-to-Rail Input and Output Yes Yes Yes Yes Yes
Shutdown Control Yes Yes Yes Yes Yes, active behavior differs by family option

Principaux différenciateurs

  • Low operating current supports portable analog conditioning (vs TLV2450IDG4)
  • Rail-to-rail operation maximizes low-voltage signal range (vs TLV2450AIDG4)
  • Shutdown support enables duty-cycled low-power operation (vs TLV2451ID)

Notes de conception

The TLV2450ID consumes 23 µA per channel under typical operating conditions. For a duty-cycled design, calculate average supply current from the active current, shutdown current, acquisition duration, and idle interval. Use the shutdown pin to disable the amplifier when it is not needed, but include control-pin leakage and the current drawn by the sensor, voltage reference, and supporting circuitry in the complete power budget.

Place the amplifier input, feedback resistors, and output components close to the corresponding pins. Keep the noninverting and inverting traces short, use a continuous ground reference, and route them away from switching-converter nodes. If the input source has high source impedance, add filtering close to the amplifier rather than at the remote sensor, where electrostatic discharge and leakage could affect the signal.

The 220 kHz gain-bandwidth product limits useful closed-loop bandwidth according to the selected noise-gain and phase-margin requirements. Before finalizing a gain stage, evaluate settling, capacitive loading, and stability rather than relying only on nominal bandwidth. Place optional output isolation or compensation networks close to the output pin and verify them across the complete supply-voltage range.

Do not assume that every TLV245x-family orderable MPN has identical shutdown polarity or qualification limits. Confirm the active shutdown level, pin configuration, temperature range, and absolute maximum ratings in the manufacturer datasheet before replacing TLV2450ID. Also account for output swing limits under load; rail-to-rail operation does not guarantee that the output can reach either rail exactly under every load condition.

Informations de conformité

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Yes
Sans halogène
Unknown
Minerais de conflit
Unknown

RoHS-compliant and lead-free construction are identified in the component listing. No automotive qualification, REACH declaration, halogen-free declaration, or conflict-minerals statement is established for TLV2450ID.

Données vérifiées le : 2026-11-10 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

TLV2450ID datasheet TLV2450ID datasheet pdf TLV2450ID pinout TLV2450ID specifications Texas Instruments TLV2450ID TLV2450ID 220kHz 23uA TLV2450ID 8-SOIC pinout TLV2450ID battery powered sensor TLV2450ID vs TLV2451ID TLV2450ID equivalent TLV2450ID drop-in replacement TLV2450ID price

Composants & termes associés

Texas Instruments TLV2450ID TLV2450IDG4 TLV2450AIDG4 TLV2450AID TLV2451ID operational amplifier voltage amplifier analog signal conditioning rail-to-rail input rail-to-rail output RRIO low-power amplifier gain-bandwidth product GBW quiescent current shutdown control input offset voltage 8-SOIC SOIC package family surface mount sensor conditioning industrial monitoring battery-powered instrumentation RoHS lead-free
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ