TLV2765CD - 1.8V Micro-Power Quad Op Amp | Texas Instruments
N.º da peça: TLV2765CD ✓ AtivoTLV2765CD Visão geral
A rail-to-rail input/output operational amplifier is a general-purpose amplifier whose input and output stages operate close to the supply rails. This topology allows the TLV2765CD to process low-voltage signals without requiring a midpoint-bias reference near mid-supply. As a quad amplifier, it combines four amplifier channels, shutdown control, and CMOS input characteristics in one 16-pin SOIC package, reducing board area when several low-voltage signals must be conditioned.
The principal features include a low 1.8 V operating supply, a maximum supply voltage of 3.6 V, rail-to-rail input and output operation, and approximately 20 uA of supply current per channel. Shutdown reduces the supply current to approximately 10 nA per channel. The family datasheet identifies a 500 kHz bandwidth for the TLV2765 device and an input offset voltage of 3500 uV for the CD grade. These characteristics make the amplifier appropriate for battery-powered instrumentation, sensor interfaces, and low-voltage analog signal chains.
The TLV2765 belongs to the TLV2764 and TLV2765 family of CMOS operational amplifiers with shutdown. Its rail-to-rail input stage supports operation near the lower and upper limits of the supply, while the rail-to-rail output stage provides useful output swing on low-voltage rails. Because the device is intended for micropower systems, total quiescent current and shutdown behavior are central to its system-level power budget.
Typical uses include portable sensor conditioning, low-voltage transimpedance stages, battery-powered monitor circuits, general-purpose analog filtering, and embedded data-acquisition interfaces. Designers can use the four channels for gain, buffering, level shifting, active filtering, or comparator-style functions where open-loop operation is appropriate. The shutdown function is useful when one subsystem must be disconnected while the rest of a low-power instrument remains active.
PCB design should keep input and feedback paths short and place input-referenced bypass capacitance close to the supply pins. Check output swing against the selected input and output voltages, because rail-to-rail operation does not guarantee a full rail-to-rail output under every load. For stable operation in amplifier configurations, follow the capacitance limits and recommended feedback values in the family datasheet.
This product page combines the TLV2765CD operating characteristics with package guidance, application analysis, comparison criteria, and practical design notes. It is intended to help engineers evaluate the TLV2765CD for low-voltage, micro-power signal-processing designs before finalizing a PCB or production BOM.
Alternativas drop-in para TLV2765CD — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
TLV2765ID
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TLV2765CD Classificações máximas e características elétricas
| Number of Amplifier Channels | 4 channels |
| Minimum Supply Voltage | 1.8 V |
| Maximum Supply Voltage | 3.6 V |
| Supply Current per Channel | 20 uA |
| Shutdown Supply Current per Channel | 10 nA |
| Gain-Bandwidth Product | 500 kHz |
| Input Offset Voltage | 3500 uV |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Input Type | CMOS |
| Shutdown Control | Yes |
| Faixa de temperatura de operação | 0 C to +70 C |
| Encapsulamento | 16-pin SOIC |
| Tipo de montagem | Surface mount |
| Product Type | Quad operational amplifier |
| Amplifier Class | General-purpose amplifier |
Guia de Configuração de Pinos do TLV2765CD 16-pin soic
Configuração de pinos para TLV2765CD (pacote 16-pin soic). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para TLV2765CD.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
TLV2765CD é adequado para 6 aplicaçãos: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Sensor Interface, Portable Data Acquisition, Low-Voltage Audio and Control, Battery-Powered IoT Node.
Battery-Powered Sensor Conditioning
The TLV2765CD suits low-voltage sensor interfaces because it operates from a 1.8 V supply and consumes approximately 20 uA per channel. Rail-to-rail input operation is valuable when the sensor output approaches either supply rail, while the rail-to-rail output stage provides useful signal swing at low voltage. Four channels can provide buffering, gain, and active filtering around a compact sensor module. Shutdown can disconnect the amplifier during inactive measurement intervals, with the family datasheet specifying approximately 10 nA per channel in that state.
Recomendado
Portable Medical Monitoring
The TLV2765CD can provide low-voltage amplification and buffering for compact monitoring equipment operating from a 1.8 V rail. Its rail-to-rail input stage accepts signals near the supply limits, and the quad configuration supports several sensing channels without requiring separate packages. The approximately 20 uA per-channel supply current is important for battery life, while shutdown allows unused channels or subsystems to remain in a low-current state. Medical designs must still validate the complete signal chain, isolation requirements, and applicable regulatory standards independently of the amplifier.
Recomendado
Industrial Sensor Interface
For industrial instrumentation, the TLV2765ID is the appropriate family variant when operation across -40 C to +85 C is required. It retains the 16-pin SOIC format, 1.8 V minimum supply, rail-to-rail input and output behavior, and 500 kHz bandwidth associated with the TLV2765 family. The low 20 uA per-channel current supports compact distributed measurement systems, while shutdown provides a controllable low-current state. The CD grade remains appropriate when the enclosure stays within 0 C to +70 C.
Recomendado
Portable Data Acquisition
The TLV2765CD is well suited to compact, low-voltage data-acquisition front ends that must amplify several inputs. Its four channels can serve as non-inverting amplifiers, buffers, or active-filter stages, while the 500 kHz gain-bandwidth product provides bandwidth for moderate-speed instrumentation. Operation from 1.8 V supports conversion to lower supply rails, and approximately 20 uA per channel limits amplifier contribution to portable-system power. Designers should verify input bandwidth, settling behavior, output loading, and accuracy for the selected gain and signal bandwidth.
Recomendado
Low-Voltage Audio and Control
The TLV2765CD can amplify and buffer low-level audio or control signals in portable equipment powered from a 1.8 V rail. Rail-to-rail inputs and outputs improve usable signal range when supply voltage is constrained, while the quad package provides four independent channels for volume, filtering, and interface functions. The approximately 20 uA per-channel current is useful for energy-sensitive designs, and the 500 kHz bandwidth covers many control and general audio paths. Verify output swing, capacitive-load behavior, and channel-to-channel performance against the intended signal.
Recomendado
Battery-Powered IoT Node
The TLV2765CD is useful in an IoT sensor node that operates from a low-energy supply and must process several small analog signals. Its 1.8 V operating capability and approximately 20 uA per-channel consumption support long standby intervals, while shutdown reduces the stated supply current to approximately 10 nA per channel. Rail-to-rail input and output stages improve signal utilization in compact mixed-signal nodes. The host microcontroller, radio, sensor, and power converter remain the dominant system-level considerations, so the amplifier should be enabled and disabled according to the node's measurement schedule.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TLV2765CD — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TLV2765ID |
|---|---|---|
| Package | 16-SOIC | 16-SOIC - same |
| Brand | Texas Instruments | Texas Instruments |
| Number of Channels | 4 | 4 |
| Minimum Supply Voltage | 1.8 V | 1.8 V |
| Maximum Supply Voltage | 3.6 V | 3.6 V |
| Supply Current per Channel | 20 uA | 20 uA |
| Shutdown Current per Channel | 10 nA | 10 nA |
| Gain-Bandwidth Product | 500 kHz | 500 kHz |
| Input Offset Voltage Maximum | 3500 uV | 3500 uV |
| Operating Temperature Range | 0 C to +70 C | -40 C to +85 C |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Shutdown Function | Yes | Yes |
Principais diferenciais
- Commercial-temperature grade for cost-sensitive commercial equipment (vs TLV2765ID)
- Four low-power channels in one package (vs TLV2765ID)
- Low-voltage rail-to-rail operation (vs TLV2765ID)
Notas de projeto
Place supply bypass capacitance close to the device's supply and ground pins, and keep amplifier input and feedback traces short to reduce coupling from adjacent switching circuits. For low-voltage designs, treat the entire input and feedback network as sensitive to leakage, contamination, and board-surface currents; use suitable guarding and clean PCB materials when very high input impedance is required.
Estimated: active supply current is approximately 20 uA per channel, so four continuously enabled channels can draw approximately 80 uA before including the device's shutdown-state bias and external load. If shutdown places the device at approximately 10 nA per channel, four disabled channels would draw approximately 40 nA. These are arithmetic estimates based on the family datasheet values; verify the final power budget at the actual supply voltage, temperature, and output state.
Do not assume that rail-to-rail input or output operation means the output can reach either supply rail exactly. Check the output-swing conditions for the chosen load and output voltage, and verify that the input remains within the common-mode range over temperature. Also confirm that the shutdown pin polarity and state in the family datasheet match the system power-sequencing requirements.
Use the family datasheet's recommended feedback resistor and capacitive-load limits when driving cables, ADC inputs, or other capacitive networks. The 500 kHz gain-bandwidth product is a small-signal characteristic and does not by itself define large-signal settling, slew rate, or output-current capability. Simulate the complete gain stage and verify settling time with the intended load and signal pattern.
Informações de conformidade
Compliance status was not stated in the available component pages. The TLV2765CD is a general-purpose commercial-temperature amplifier rather than an AEC-Q100-qualified automotive device.