TLV4110IP - 300mA Rail-to-Rail Op Amp with Shutdown | TI
N.º da peça: TLV4110IP ✓ AtivoTLV4110IP Visão geral
An operational amplifier is a voltage-feedback amplifier used to amplify, filter, buffer, or drive signals in electronic systems. The TLV4110IP belongs to the general-purpose operational-amplifier family within analog signal-chain semiconductors. Rail-to-rail output allows the output voltage to approach the supply limits more closely than a conventional amplifier whose useful output range is restricted by saturation headroom. The shutdown function provides a controlled means of placing the amplifier in a low-power state when the output must be isolated.
The primary feature of the TLV4110IP is its high output-drive capability. According to the manufacturer datasheet, the TLV411x family can supply output currents in excess of 300 mA at 5 V. This makes the device suitable for use as a high-current buffer or in coil-driver applications where a standard operational amplifier may experience current-limit distortion. The 2.7 MHz gain-bandwidth product provides useful bandwidth for low- and moderate-frequency precision signal-conditioning applications.
The TLV4110 is a single-amplifier device intended for low-voltage, single-supply operation. Rail-to-rail output improves usable signal swing in sensor interfaces, audio paths, and low-level analog front ends. An active shutdown connection allows a system controller to disable the amplifier during idle periods, reducing power consumption and helping isolate downstream circuitry. Because the output stage can deliver substantially more current than typical general-purpose amplifiers, PCB layout, supply decoupling, load-return paths, and thermal performance require careful attention.
Typical uses include high-current buffer stages, coil drivers, line-driver circuits, sensor-conditioning blocks, audio preamplifiers, and low-voltage portable equipment. In a sensor interface, the amplifier can provide gain while driving a higher-capacitance input stage. In a coil-driver circuit, its output current capability is more useful than a conventional precision op amp. The shutdown pin is valuable in portable or duty-cycled systems where active operation is required only during selected intervals.
When designing around the TLV4110IP, keep the power and ground connections short and place the required bypass capacitors close to the device. Avoid sustained operation at the current limit because dissipation rises with output voltage and current. Check the load, wiring resistance, supply capability, and thermal rise together, especially when driving coils or resistive loads. The manufacturer datasheet should be used to assign every package pin and confirm operating limits.
This product page combines the manufacturer device information with a practical comparison of compatible family options, application-focused design guidance, pin-level implementation notes, and sourcing data. It is intended to help engineers identify whether the TLV4110IP's combination of 300 mA-class drive, 2.7 MHz bandwidth, rail-to-rail output, shutdown control, and 8-pin DIP package is suitable for a new amplifier or buffer design.
Alternativas drop-in para TLV4110IP — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com TLV4110IP (mesmo formato e footprint).
TLV4111IP
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
TLV4112IP
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →TLV4113IP
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TLV4110IP Classificações máximas e características elétricas
| Nenhuma especificação disponível |
Configuração de pinos do TLV4110IP
| Pino 1 | OUT — Amplifier output |
| Pino 2 | IN- — Inverting input |
| Pino 3 | IN+ — Non-inverting input |
| Pino 4 | V- — Negative supply or ground connection |
| Pino 5 | NC — Not connected |
| Pino 6 | SHDN — Shutdown control input |
| Pino 7 | NC — Not connected |
| Pino 8 | V+ — Positive supply connection |
Aplicações típicas
TLV4110IP é adequado para 6 aplicaçãos: High-Current Signal Buffer, Coil Driver, Sensor Signal Conditioning, Portable Audio Preamplifier, Industrial Line Driver, Low-Voltage Test and Measurement Buffer.
High-Current Signal Buffer
The TLV4110IP fits high-current buffer stages because the manufacturer datasheet identifies output current greater than 300 mA at 5 V and a 2.7 MHz gain-bandwidth product. Place it between a low-level signal source and a load such as a sensor, analog test point, or moderate-capacitance input stage. Its rail-to-rail output preserves more of the available signal range than a restricted-output amplifier, while the single PDIP package simplifies through-hole prototyping. Because this is not a conventional low-current precision op amp, verify output impedance, stability, load transients, and thermal dissipation before finalizing the PCB. Decoupling should be placed close to the supply pins, and the high-current return path should avoid sharing narrow traces with sensitive analog signals.
Recomendado
Coil Driver
The TLV4110IP is suited to low-voltage coil-driver circuits because its output can exceed 300 mA at 5 V, according to the Texas Instruments manufacturer datasheet. In a flyback-return or transistor-driver arrangement, the amplifier can provide the current required to charge a small relay or electromagnetic actuator while retaining a 2.7 MHz gain-bandwidth product for control-loop bandwidth. The key engineering trade-off is dissipation: both output current and output voltage contribute to amplifier heat, so duty cycle and load resistance determine allowable continuous drive. Use an appropriate flyback diode or clamp path, keep switching current away from analog input traces, and confirm the shutdown behavior before switching the coil.
Recomendado
Sensor Signal Conditioning
The TLV4110IP can condition low-level sensor signals in a single-supply system while providing more output-drive margin than a typical precision amplifier. Its rail-to-rail output is useful when the amplified signal must approach a supply rail, and the 2.7 MHz gain-bandwidth product supports moderate-bandwidth gain stages. For bridge, temperature, or pressure sensing, the designer should still verify input common-mode range, input bias current, offset voltage, and noise because those values are not established by the manufacturer page excerpt. Place the sensor return and amplifier ground on a quiet path, use short input traces, and avoid routing the relay or coil current through the same impedance as the sensing node. A shutdown control can disable the stage when the sensor is sampled intermittently.
Recomendado
Portable Audio Preamplifier
The TLV4110IP is applicable to a low-voltage audio preamplifier or line buffer where the output must drive a downstream stage and the signal is referenced to a single supply. Rail-to-rail output increases usable swing, while the greater-than-300 mA drive capability at 5 V provides more margin than a conventional small-signal op amp. The 2.7 MHz gain-bandwidth product is suitable for audio-band gain and filtering stages rather than high-frequency video work. The shutdown function can reduce consumption when the audio path is inactive, although the exact logic level and disabled-output state must be confirmed in the datasheet. Use a low-noise decoupling arrangement, keep the return path away from switching converters, and verify THD, slew rate, output swing, and stability at the intended load.
Recomendado
Industrial Line Driver
The TLV4110IP can serve as the output stage of a low-voltage industrial line driver when the connected load requires substantially more current than a standard precision operational amplifier can provide. Its output drive greater than 300 mA at 5 V helps reduce current-limit distortion, while rail-to-rail operation supports systems that do not use a mid-supply reference. The 2.7 MHz gain-bandwidth product provides enough closed-loop bandwidth for many low-speed control and instrumentation signals. For an industrial environment, isolate analog input routing from relay and motor currents, include protection against external transients, and use the shutdown input to place the driver in a defined inactive state. Confirm loop stability and output response into the actual cable or load before production.
Recomendado
Low-Voltage Test and Measurement Buffer
The TLV4110IP is useful as an output buffer in a compact test or measurement instrument when the source impedance is low and the instrument must drive a moderate external load. The greater-than-300 mA output capability at 5 V offers more drive margin than a conventional precision buffer, and the 2.7 MHz gain-bandwidth product supports general-purpose measurement bandwidth. Rail-to-rail output can maximize range in a single-supply instrument, while shutdown can disable the buffer between measurements. Designers should verify input offset, bias current, output swing, noise, and stability using the complete datasheet because those specifications govern precision accuracy. Keep sensitive input nodes away from the high-current output return, provide local supply bypassing, and include protection for external test leads and fixture transients.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TLV4110IP — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TLV4111IP | TLV4112IP | TLV4113IP |
|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
Principais diferenciais
- High output-drive capability for a single low-voltage amplifier (vs LM6181IN)
- Shutdown capability in the standard TLV4110 function (vs TLV4113IP)
- Through-hole PDIP implementation (vs TLV4110IDR)
Notas de projeto
The TLV4110IP can deliver output current above 300 mA at 5 V, so its supply network must support the load rather than only the amplifier's quiescent current. Place the required bypass capacitor close to the supply pins and use a low-impedance return path from load current to the supply bypass point. Avoid sharing narrow copper between the output load and sensitive input or reference traces. Verify supply droop, current-limit behavior, and startup effects with the intended load attached.
Estimated: amplifier dissipation is approximately P = (VOUT - VLOAD) × IOUT, with IOUT potentially approaching the greater-than-300 mA capability at 5 V. For example, 100 mA across a 2 V output difference produces an estimated 200 mW dissipation. The actual junction temperature also depends on package thermal resistance, ambient temperature, PCB copper, duty cycle, and output waveform. Use the manufacturer maximum-power and thermal limits for the final design.
Treat the output and load current as a high-current path even though the package is an 8-pin PDIP. Keep the output route short, use adequate copper width, and connect the load return directly toward the supply bypass capacitor. Sensitive input and shutdown traces should not share this path. The shutdown connection should also be routed away from switching-node copper and protected if the control source can experience transients.
Do not assume that a generic 8-pin operational amplifier can replace the TLV4110IP solely because both use DIP packages. Check pin names, shutdown presence and polarity, supply range, output-current limit, input common-mode range, stability, and package pinout in the manufacturer datasheet. Likewise, do not operate the output continuously at its maximum drive rating without evaluating dissipation and load behavior.
Informações de conformidade
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement appears in the manufacturer-page or distributor-listing excerpts reviewed for this product.