Texas Instruments

TLV4110IP - 300mA Rail-to-Rail Op Amp with Shutdown | TI

MPN: TLV4110IP ✓ فعال
MOQ: 1 |

TLV4110IP جائزہ

The Texas Instruments TLV4110IP is a low-voltage, single operational amplifier with rail-to-rail output, shutdown capability, and an output current exceeding 300 mA at a 5 V supply. The device is offered in an 8-pin dual inline package and operates at a gain-bandwidth product of 2.7 MHz. Its combination of broad output-current capability, single-supply operation, and shutdown control makes it suitable for signal buffering and load-driving circuits that exceed the current limits of a conventional low-power operational amplifier.

An operational amplifier is a voltage-feedback amplifier used to amplify, filter, buffer, or drive signals in electronic systems. The TLV4110IP belongs to the general-purpose operational-amplifier family within analog signal-chain semiconductors. Rail-to-rail output allows the output voltage to approach the supply limits more closely than a conventional amplifier whose useful output range is restricted by saturation headroom. The shutdown function provides a controlled means of placing the amplifier in a low-power state when the output must be isolated.

The primary feature of the TLV4110IP is its high output-drive capability. According to the manufacturer datasheet, the TLV411x family can supply output currents in excess of 300 mA at 5 V. This makes the device suitable for use as a high-current buffer or in coil-driver applications where a standard operational amplifier may experience current-limit distortion. The 2.7 MHz gain-bandwidth product provides useful bandwidth for low- and moderate-frequency precision signal-conditioning applications.

The TLV4110 is a single-amplifier device intended for low-voltage, single-supply operation. Rail-to-rail output improves usable signal swing in sensor interfaces, audio paths, and low-level analog front ends. An active shutdown connection allows a system controller to disable the amplifier during idle periods, reducing power consumption and helping isolate downstream circuitry. Because the output stage can deliver substantially more current than typical general-purpose amplifiers, PCB layout, supply decoupling, load-return paths, and thermal performance require careful attention.

Typical uses include high-current buffer stages, coil drivers, line-driver circuits, sensor-conditioning blocks, audio preamplifiers, and low-voltage portable equipment. In a sensor interface, the amplifier can provide gain while driving a higher-capacitance input stage. In a coil-driver circuit, its output current capability is more useful than a conventional precision op amp. The shutdown pin is valuable in portable or duty-cycled systems where active operation is required only during selected intervals.

When designing around the TLV4110IP, keep the power and ground connections short and place the required bypass capacitors close to the device. Avoid sustained operation at the current limit because dissipation rises with output voltage and current. Check the load, wiring resistance, supply capability, and thermal rise together, especially when driving coils or resistive loads. The manufacturer datasheet should be used to assign every package pin and confirm operating limits.

This product page combines the manufacturer device information with a practical comparison of compatible family options, application-focused design guidance, pin-level implementation notes, and sourcing data. It is intended to help engineers identify whether the TLV4110IP's combination of 300 mA-class drive, 2.7 MHz bandwidth, rail-to-rail output, shutdown control, and 8-pin DIP package is suitable for a new amplifier or buffer design.

کے لیے ڈراپ اِن متبادل TLV4110IP — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں TLV4110IP (یکساں فارم فیکٹر اور فٹ پرنٹ).

TLV4111IP

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 8-pin PDIP
Same TLV411x family and 8-pin PDIP footprint; shutdown and electrical differences require confirmation against the target circuit.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TLV4112IP

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
Texas Instruments
📦 8-pin PDIP
General-purpose operational amplifier · 2 channels · Rail-to-rail output · Greater than 300 mA at 5 V · 2.7 MHz · 1.5 V/us · 700 uA per channel · 2.7 V

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

TLV4113IP

✅ ڈراپ-اِن
📦 8-pin PDIP
Same TLV411x family, 8-pin PDIP footprint, and shutdown capability; device-specific electrical limits must still be verified.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TLV4110IP زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

کوئی تفصیلات دستیاب نہیں

TLV4110IP پن کنفیگریشن

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
پن 1 OUT — Amplifier output
پن 2 IN- — Inverting input
پن 3 IN+ — Non-inverting input
پن 4 V- — Negative supply or ground connection
پن 5 NC — Not connected
پن 6 SHDN — Shutdown control input
پن 7 NC — Not connected
پن 8 V+ — Positive supply connection

عام استعمالات

TLV4110IP کے لیے موزوں ہے 6 ایپلیکیشنs: High-Current Signal Buffer, Coil Driver, Sensor Signal Conditioning, Portable Audio Preamplifier, Industrial Line Driver, Low-Voltage Test and Measurement Buffer.

⚡

High-Current Signal Buffer

The TLV4110IP fits high-current buffer stages because the manufacturer datasheet identifies output current greater than 300 mA at 5 V and a 2.7 MHz gain-bandwidth product. Place it between a low-level signal source and a load such as a sensor, analog test point, or moderate-capacitance input stage. Its rail-to-rail output preserves more of the available signal range than a restricted-output amplifier, while the single PDIP package simplifies through-hole prototyping. Because this is not a conventional low-current precision op amp, verify output impedance, stability, load transients, and thermal dissipation before finalizing the PCB. Decoupling should be placed close to the supply pins, and the high-current return path should avoid sharing narrow traces with sensitive analog signals.

🏭

Coil Driver

The TLV4110IP is suited to low-voltage coil-driver circuits because its output can exceed 300 mA at 5 V, according to the Texas Instruments manufacturer datasheet. In a flyback-return or transistor-driver arrangement, the amplifier can provide the current required to charge a small relay or electromagnetic actuator while retaining a 2.7 MHz gain-bandwidth product for control-loop bandwidth. The key engineering trade-off is dissipation: both output current and output voltage contribute to amplifier heat, so duty cycle and load resistance determine allowable continuous drive. Use an appropriate flyback diode or clamp path, keep switching current away from analog input traces, and confirm the shutdown behavior before switching the coil.

🧩

Sensor Signal Conditioning

The TLV4110IP can condition low-level sensor signals in a single-supply system while providing more output-drive margin than a typical precision amplifier. Its rail-to-rail output is useful when the amplified signal must approach a supply rail, and the 2.7 MHz gain-bandwidth product supports moderate-bandwidth gain stages. For bridge, temperature, or pressure sensing, the designer should still verify input common-mode range, input bias current, offset voltage, and noise because those values are not established by the manufacturer page excerpt. Place the sensor return and amplifier ground on a quiet path, use short input traces, and avoid routing the relay or coil current through the same impedance as the sensing node. A shutdown control can disable the stage when the sensor is sampled intermittently.

🎧

Portable Audio Preamplifier

The TLV4110IP is applicable to a low-voltage audio preamplifier or line buffer where the output must drive a downstream stage and the signal is referenced to a single supply. Rail-to-rail output increases usable swing, while the greater-than-300 mA drive capability at 5 V provides more margin than a conventional small-signal op amp. The 2.7 MHz gain-bandwidth product is suitable for audio-band gain and filtering stages rather than high-frequency video work. The shutdown function can reduce consumption when the audio path is inactive, although the exact logic level and disabled-output state must be confirmed in the datasheet. Use a low-noise decoupling arrangement, keep the return path away from switching converters, and verify THD, slew rate, output swing, and stability at the intended load.

🏭

Industrial Line Driver

The TLV4110IP can serve as the output stage of a low-voltage industrial line driver when the connected load requires substantially more current than a standard precision operational amplifier can provide. Its output drive greater than 300 mA at 5 V helps reduce current-limit distortion, while rail-to-rail operation supports systems that do not use a mid-supply reference. The 2.7 MHz gain-bandwidth product provides enough closed-loop bandwidth for many low-speed control and instrumentation signals. For an industrial environment, isolate analog input routing from relay and motor currents, include protection against external transients, and use the shutdown input to place the driver in a defined inactive state. Confirm loop stability and output response into the actual cable or load before production.

🔧

Low-Voltage Test and Measurement Buffer

The TLV4110IP is useful as an output buffer in a compact test or measurement instrument when the source impedance is low and the instrument must drive a moderate external load. The greater-than-300 mA output capability at 5 V offers more drive margin than a conventional precision buffer, and the 2.7 MHz gain-bandwidth product supports general-purpose measurement bandwidth. Rail-to-rail output can maximize range in a single-supply instrument, while shutdown can disable the buffer between measurements. Designers should verify input offset, bias current, output swing, noise, and stability using the complete datasheet because those specifications govern precision accuracy. Keep sensitive input nodes away from the high-current output return, provide local supply bypassing, and include protection for external test leads and fixture transients.

تجویز کردہ پروڈکٹس کا خلاصہ

TLV4111IP Same-family single operational amplifier for family-level design comparison استعمال ہوتا ہے: High-Current Signal Buffer, Sensor Signal Conditioning, Industrial Line Driver, Low-Voltage Test and Measurement Buffer TLV4113IP Same-family high-output-drive amplifier with shutdown استعمال ہوتا ہے: High-Current Signal Buffer, Coil Driver, Sensor Signal Conditioning, Portable Audio Preamplifier, Industrial Line Driver TLV4112IP Texas Instruments استعمال ہوتا ہے: Coil Driver, Portable Audio Preamplifier, Low-Voltage Test and Measurement Buffer
What is the TLV4110IP?
The TLV4110IP is a single, low-voltage operational amplifier with rail-to-rail output, shutdown control, and an output current exceeding 300 mA at 5 V. According to the Texas Instruments manufacturer datasheet, the TLV4110 and TLV4113 include a shutdown function. It is packaged in an 8-pin PDIP for through-hole PCB assembly.
What are the key specifications of TLV4110IP?
The TLV4110IP combines a 2.7 MHz gain-bandwidth product, rail-to-rail output, and output drive greater than 300 mA at a 5 V supply. The manufacturer datasheet identifies it as a single operational amplifier with shutdown, while distributor documentation identifies the TLV4110IP package as 8-pin PDIP. Use the datasheet for complete input, output, supply-current, and absolute-maximum ratings.
Why is the TLV4110IP suitable for high-current buffering?
The TLV4110IP can produce output current in excess of 300 mA at 5 V, which is substantially greater than the drive typically expected from a conventional low-power precision operational amplifier. According to the Texas Instruments datasheet, this allows standard pin-out amplifiers to serve as high-current buffers or in coil-driver applications. Continuous output-current operation still requires thermal and load-path verification.
What is the TLV4110IP gain-bandwidth product?
The TLV4110IP has a gain-bandwidth product of 2.7 MHz. This bandwidth permits useful closed-loop performance in low- and moderate-frequency signal-conditioning, buffering, and drive circuits. The achievable closed-loop bandwidth still depends on the selected noise gain, operating voltage, output load, and amplifier stability behavior documented in the manufacturer datasheet.
What is the difference between TLV4110IP and TLV4110IDR?
The TLV4110IP is packaged in an 8-pin PDIP, while TLV4110IDR uses an 8-pin SOIC package. Both identify the same TLV4110 family functional variant, but the physical footprints are different, so TLV4110IDR is not a drop-in replacement for TLV4110IP without changing the PCB. Confirm electrical limits and orderable status for each package in the manufacturer documentation.
What can replace TLV4110IP?
The closest documented replacement choices are the same-family TLV4111IP, TLV4112IP, and TLV4113IP variants when their shutdown and electrical characteristics satisfy the circuit. The TLV4110IP must retain the 8-pin PDIP footprint for a true drop-in board-level substitution. A candidate should be checked for shutdown polarity, supply range, output-current capability, stability, and thermal performance before substitution.
Is LM6181IN a drop-in replacement for TLV4110IP?
The LM6181IN is not a confirmed drop-in replacement for the TLV4110IP because the comparison identifies a different amplifier architecture, and the published comparison does not establish every pin, shutdown, stability, or current-limit characteristic as equivalent. Although both are described as 8-pin DIP devices, matching the package alone is insufficient. Use the manufacturer pin descriptions and electrical tables to verify a replacement.
When should I choose TLV4110IP over TLV4113IP?
Choose the TLV4110IP when the design requires a single operational amplifier in an 8-pin PDIP package and can use its shutdown behavior and output-drive characteristics. Choose the TLV4113IP only after checking its electrical and shutdown details against the target circuit. Both are members of the TLV411x high-output-drive family, so the decisive factors are package, control polarity, and application-specific limits.
Is TLV4110IP suitable for coil-driver applications?
Yes, the TLV4110IP is suitable for coil-driver and high-current buffer roles because its output current can exceed 300 mA at 5 V according to the manufacturer datasheet. Its usefulness depends on supply voltage, coil resistance, flyback handling, duty cycle, and thermal rise. The coil must use an appropriate protection path, and sustained near-limit current should be checked against the package dissipation limits.
Where can I download the TLV4110IP datasheet PDF?
The official TLV4110 product page at Texas Instruments is the preferred starting point for the manufacturer datasheet and ordering information. Use the pin-description table, electrical characteristics, and application information there when assigning the 8-pin PDIP or designing the shutdown connection. The product page also links the exact TLV4110IP part details and related package options.
Where is the TLV4110IP pinout located?
The TLV4110IP pinout is shown in the pin-configuration section of the Texas Instruments TLV4110 manufacturer datasheet. The device uses eight pins in a PDIP package. Assign the power, ground, input, output, shutdown, and no-connect pins from the datasheet diagram rather than relying only on package orientation, because the shutdown implementation distinguishes this family from related amplifiers.
What is the shutdown function of TLV4110IP?
The TLV4110IP includes a shutdown function that allows the amplifier to be disabled when it is not needed. The manufacturer states that the TLV4110 and TLV4113 come with shutdown, supporting low-power or duty-cycled equipment designs. Confirm the shutdown logic level, transition timing, output state, and supply-current reduction in the datasheet before using the control pin in a safety-related sequence.
How much current can the TLV4110IP output drive?
The TLV4110IP can deliver output current in excess of 300 mA at a 5 V supply, according to the Texas Instruments datasheet. This rating describes drive capability, not continuous power dissipation that every load may tolerate. The actual operating point depends on output voltage, supply voltage, load resistance, copper area, ambient temperature, and the amplifier's short-circuit and thermal behavior.
Where can I buy TLV4110IP and what is its price?
The TLV4110IP can be requested through the Request a Quote form on this page, which supports current sourcing, stock confirmation, and lead-time inquiries. Use that form for the exact 8-pin PDIP orderable MPN and the quantity required. Requesting the exact suffix avoids package, carrier, temperature, or grade mismatches in new production designs.
What is the lead time and stock status for TLV4110IP?
Use the Request a Quote form on this page to request the current stock position, minimum order quantity, and production lead time for TLV4110IP. The form is the appropriate route for a date-sensitive availability answer because channel inventory can change without notice. Include the required quantity, target date, and any approved manufacturer-source constraints in the request.

کے لیے انجینئرنگ ریفرنس ڈیٹا TLV4110IP — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the TLV4110IP when the design needs a single low-voltage amplifier that combines rail-to-rail output with unusually strong drive, specifically more than 300 mA at 5 V, and when an 8-pin through-hole PDIP is acceptable. It is particularly useful for small coil drivers, line buffers, sensor-conditioning outputs, and portable audio paths where a standard low-current precision amplifier may limit or distort the load. Select TLV4111IP or TLV4112IP when their family-specific electrical and shutdown characteristics provide a closer functional match, but verify their pin-level behavior before treating them as drop-in parts. TLV4113IP is a logical family comparison because it also includes shutdown, although its specific ratings must be checked. Do not select LM6181IN solely by package; its current-feedback architecture requires a different stability and compensation assessment. In every case, verify supply range, input and output limits, shutdown logic, output stability, and thermal dissipation in the manufacturer datasheet.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ TLV4111IP TLV4112IP TLV4113IP
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments

اہم امتیازی خصوصیات

  • High output-drive capability for a single low-voltage amplifier (بمقابلہLM6181IN)
  • Shutdown capability in the standard TLV4110 function (بمقابلہTLV4113IP)
  • Through-hole PDIP implementation (بمقابلہTLV4110IDR)

ڈیزائن نوٹس

The TLV4110IP can deliver output current above 300 mA at 5 V, so its supply network must support the load rather than only the amplifier's quiescent current. Place the required bypass capacitor close to the supply pins and use a low-impedance return path from load current to the supply bypass point. Avoid sharing narrow copper between the output load and sensitive input or reference traces. Verify supply droop, current-limit behavior, and startup effects with the intended load attached.

Estimated: amplifier dissipation is approximately P = (VOUT - VLOAD) × IOUT, with IOUT potentially approaching the greater-than-300 mA capability at 5 V. For example, 100 mA across a 2 V output difference produces an estimated 200 mW dissipation. The actual junction temperature also depends on package thermal resistance, ambient temperature, PCB copper, duty cycle, and output waveform. Use the manufacturer maximum-power and thermal limits for the final design.

Treat the output and load current as a high-current path even though the package is an 8-pin PDIP. Keep the output route short, use adequate copper width, and connect the load return directly toward the supply bypass capacitor. Sensitive input and shutdown traces should not share this path. The shutdown connection should also be routed away from switching-node copper and protected if the control source can experience transients.

Do not assume that a generic 8-pin operational amplifier can replace the TLV4110IP solely because both use DIP packages. Check pin names, shutdown presence and polarity, supply range, output-current limit, input common-mode range, stability, and package pinout in the manufacturer datasheet. Likewise, do not operate the output continuously at its maximum drive rating without evaluating dissipation and load behavior.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement appears in the manufacturer-page or distributor-listing excerpts reviewed for this product.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-19 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

TLV4110IP datasheet TLV4110IP specifications TLV4110IP pinout TLV4110IP datasheet pdf TLV4110IP 8-PDIP TLV4110IP 300mA TLV4110IP 2.7MHz TLV4110IP shutdown TLV4110IP equivalent TLV4110IP replacement TLV4110IP vs LM6181IN TLV4110IP coil driver TLV4110IP price TLV4110IP stock Texas Instruments TLV4110IP

متعلقہ اجزاء اور اصطلاحات

Texas Instruments TLV4110IP TLV4111IP TLV4112IP TLV4113IP LM6181IN operational amplifier single operational amplifier general-purpose amplifier rail-to-rail output high-current buffer coil driver shutdown control gain-bandwidth product 2.7 MHz greater than 300 mA at 5 V 8-pin PDIP DIP package through-hole package analog signal chain voltage-feedback amplifier current-feedback amplifier output current single-supply operation sensor signal conditioning
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں