TS3704ID - 4-Comparator 9uA CMOS IC | STMicroelectronics
N.º da peça: TS3704ID ✗ Fim de vidaTS3704ID Visão geral
A voltage comparator is an analog interface component that translates a difference between two voltages into a digital logic state. Within the broader hierarchy of integrated circuits and interface ICs, the TS3704 combines four analog comparison functions with low-power digital output stages. Unlike the open-collector outputs used by many bipolar comparator families, its push-pull outputs source and sink current directly, eliminating the external pull-up resistor normally required.
Key characteristics include 9 uA typical current consumption per comparator, 1 TΩ typical input impedance, and a 2 us typical response time for a 5 mV input step. The high input impedance minimizes loading on high-impedance sensors and divider networks. A push-pull output also provides faster signal transitions and makes the device suitable for systems that need a direct active-high or active-low logic indication without an added pull-up resistor.
The TS3704 uses CMOS input and output circuitry to achieve low bias current and low power consumption while retaining the pin arrangement associated with the LM339 family. Its four channels share supply pins but operate independently, allowing one package to implement battery monitoring, supervision, window comparison, or several unrelated threshold functions. Maximum offset voltage, input common-mode limits, supply range, and output-drive details should be checked against the manufacturer datasheet for the specific operating conditions.
Typical applications include low-voltage battery monitoring, industrial sensor thresholds, consumer power-fail detection, overvoltage and undervoltage supervision, and comparison of external reference voltages. In portable equipment, the low 9 uA typical consumption per channel helps limit standby drain, while the four-channel integration reduces package count and board area compared with discrete single comparators.
Designers should account for input common-mode range, output levels, propagation delay, and unused-channel behavior before assigning every comparator. Inputs must remain within their specified operating range, and unused channels should be configured according to the manufacturer guidance rather than left floating. PCB placement should keep sensitive comparison nodes away from switching nodes and high-current return paths to minimize coupled errors.
This page organizes the TS3704ID electrical characteristics, package and pin information, application guidance, lifecycle status, and confirmed drop-in alternatives into one design-focused reference. It also identifies where a direct substitution is not established, helping engineers distinguish a true same-footprint replacement from a merely similar quad comparator.
Alternativas drop-in para TS3704ID — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
TS3704CDT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TS3V3704ID
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TS3V3704IN
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TS3704ID Classificações máximas e características elétricas
| Comparator Type | General-purpose quad voltage comparator |
| Number of Channels | 4 channels |
| Supply Current per Comparator | 9 uA typical |
| Input Impedance | 1 TOhm typical |
| Input Bias Current | 0.0006 uA |
| Maximum Input Offset Voltage | 6500 uV |
| Response Time | 2 us typical for a 5 mV step |
| Tipo de saída | Push-pull CMOS |
| Logic States | 2 logic states |
| Temperatura de operação | -40 C to +125 C |
| Nominal Supply Voltage | 3 V |
| Maximum Power Dissipation | 830 mW |
| Encapsulamento | 14-pin SOIC |
| Tipo de montagem | Surface mount |
| External Pull-Up Resistor | Not required for push-pull outputs |
| Status RoHS | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
Configuração de pinos do TS3704ID
| Pino 1 | OUT1 — Comparator 1 output |
| Pino 2 | IN1- — Comparator 1 inverting input |
| Pino 3 | IN1+ — Comparator 1 non-inverting input |
| Pino 4 | GND — Ground connection |
| Pino 5 | IN2+ — Comparator 2 non-inverting input |
| Pino 6 | IN2- — Comparator 2 inverting input |
| Pino 7 | OUT2 — Comparator 2 output |
| Pino 8 | OUT3 — Comparator 3 output |
| Pino 9 | IN3- — Comparator 3 inverting input |
| Pino 10 | IN3+ — Comparator 3 non-inverting input |
| Pino 11 | VCC — Positive supply connection |
| Pino 12 | IN4+ — Comparator 4 non-inverting input |
| Pino 13 | IN4- — Comparator 4 inverting input |
| Pino 14 | OUT4 — Comparator 4 output |
Aplicações típicas
TS3704ID é adequado para 6 aplicaçãos: Battery Voltage Monitoring, Industrial Sensor Threshold Detection, Overvoltage and Undervoltage Supervision, Low-Power Sensor Interface, Power-Fail and Sequence Control, Portable Equipment and Wearables.
Battery Voltage Monitoring
The TS3704ID is suitable for monitoring battery rails or divider-derived voltages in portable equipment. Its 9 uA typical supply current per comparator helps preserve standby capacity, while the 1 TOhm typical input impedance reduces loading on high-value battery dividers. Each channel can compare an adjustable threshold with a divided supply voltage and produce a direct push-pull logic result. Because the output stage sources and sinks current, no pull-up resistor is required, simplifying the interface to a system supervisor or microcontroller input. Designers should confirm the input common-mode range across the complete battery discharge profile and verify the selected TS3704ID grade against the product's temperature requirements.
Recomendado
Industrial Sensor Threshold Detection
The TS3704ID can convert slow or high-impedance sensor signals into logic states for factory equipment, process monitoring, and condition sensing. Its 1 TOhm typical input impedance is valuable when the sensor or divider has high source impedance, while the 2 us typical response for a 5 mV step provides adequate speed for many threshold and alarm functions. Four independent channels allow one device to monitor several limits, reducing board area and component count. Push-pull outputs simplify downstream digital signaling because they require no external pull-up resistor. At the board level, route the sensor input away from motors, relay contacts, and power-conversion switching nodes to prevent threshold errors from capacitive or inductive coupling.
Recomendado
Overvoltage and Undervoltage Supervision
The TS3704ID is appropriate for window supervision in industrial controls, power modules, and embedded systems. Two channels can detect an upper voltage threshold while another channel detects a lower threshold, and the fourth channel can supervise an auxiliary rail. Each comparator consumes 9 uA typical, supporting low-power supervisory circuitry, and the push-pull CMOS output can directly drive a logic input or fault signal. The 1 TOhm typical input impedance helps preserve accuracy in resistor dividers. For reliable operation, calculate divider tolerances, include hysteresis to prevent repeated switching near a threshold, and verify that the monitored voltage remains within the comparator's specified input common-mode limits during startup and fault conditions.
Recomendado
Low-Power Sensor Interface
The TS3704ID can interface resistive, capacitive, or high-impedance sensors whose output must be compared with a reference voltage. Its CMOS input stage provides 1 TOhm typical impedance and 0.0006 uA input bias current, minimizing errors in high-source-impedance networks. The low 9 uA typical channel current is useful in energy-limited IoT devices that periodically wake to check a physical condition. A push-pull output simplifies connection to a low-power microcontroller because no external pull-up is needed. The 2 us typical response time is suitable for slow threshold events and alarm generation. Place reference and sensor inputs on quiet PCB tracks, use a stable reference source, and specify resistor networks with suitable tolerance and temperature characteristics.
Recomendado
Power-Fail and Sequence Control
The TS3704ID can implement power-fail detection, reset generation, or simple power-sequence decisions by comparing a divided rail with a reference. Its low typical consumption reduces the impact of always-on supervision, while the four channels allow multiple rails to be checked independently. The push-pull CMOS output provides a defined driven state without a pull-up resistor, although the source and sink capability must remain compatible with the receiving gate and cable capacitance. Add hysteresis around the switching point to avoid repeated fault assertions during supply ripple. Confirm the comparator's operating and input voltage limits against the complete startup sequence, especially during rail ramp-up when intermediate voltages may move through the monitored range.
Recomendado
Portable Equipment and Wearables
The TS3704ID fits portable equipment and wearable designs that compare battery-derived or sensor-derived voltages while keeping standby consumption low. At 9 uA typical per comparator, four channels provide multiple threshold functions without the supply demand of bipolar quad comparators. The 1 TOhm typical input impedance is particularly helpful when monitoring high-impedance dividers or electrode-like sensing networks. Push-pull outputs reduce external component count and produce predictable logic levels for a low-power controller. In a compact wearable layout, protect sensitive inputs from display and radio switching energy, use short ground returns, and verify that current consumption remains acceptable during every operating mode. The device's package dimensions also support integration where a 14-pin SOIC is acceptable.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TS3704ID — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TS3704CDT | TS3V3704ID | TS3V3704IN |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 14-pin SOIC | 14-pin SOIC - same footprint | 14-pin SOIC - same footprint | 14-pin SOIC - same footprint |
| Comparator Count | 4 | 4 | 4 | 4 |
| Output Type | Push-pull CMOS | Push-pull CMOS | Push-pull CMOS | Push-pull CMOS |
Principais diferenciais
- Low typical current consumption (vs LM339)
- No external output pull-up required (vs LM339)
- High input impedance for threshold networks (vs TS3704CDT)
- Four channels in one 14-pin SOIC (vs Discrete single comparators)
Notas de projeto
The TS3704ID consumes 9 uA typical per comparator. Estimated: four active channels at this typical condition draw about 36 uA, excluding dynamic output current and supply-system overhead. Calculate the complete standby budget from the actual number of active channels, supply voltage, and leakage limits before assigning it to a battery-powered design.
Keep each non-inverting and inverting input on a compact, quiet route connected to a solid ground reference. Separate sensitive threshold traces from relay-coil, motor, display, and switching-converter paths. If a sensing source has high source impedance, minimize PCB leakage, connector contamination, and nearby high-impedance nodes that could couple interference into the comparator input.
Do not treat every LM339-family footprint as automatically interchangeable. The TS3704ID has a push-pull CMOS output and therefore does not need the pull-up resistor required by a conventional open-collector LM339 output. Review the installed pull-up network, output drive expectations, input common-mode range, and logic polarity before replacing an LM339 with this device.
Add deliberate hysteresis where the compared signals can cross slowly or where output chatter would be harmful. The exact resistor values depend on the input bias current, noise level, source impedance, and desired switching margin. Validate the threshold behavior over temperature and supply tolerance rather than relying only on a nominal room-temperature calculation.
Informações de conformidade
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the available product documentation excerpts.