STMicroelectronics

TS391ILT - Low-Power Single Comparator | STMicroelectronics

N.º da peça: TS391ILT ✓ Ativo
2 V to 34 V Vdss 0.2 mA typical Id SOT-23-5, 5 pins Package
MOQ: 1 |

TS391ILT Visão geral

The STMicroelectronics TS391ILT is a low-power, single voltage comparator with a supply range of 2 V to 34 V, a response time of approximately 0.3 µs to 1.3 µs depending on the operating condition, and an open-collector output. The device is packaged in a 5-pin SOT-23 surface-mount package for compact analog signal-conditioning and threshold-detection circuits.

A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital output indicating which input is higher. The TS391 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its low-power design makes it useful where continuous monitoring is required, including industrial control, sensor interfaces, power-supply sequencing, battery monitoring, and portable equipment.

Key characteristics include very low supply-current consumption, low input bias current, low input-offset voltage, and an input common-mode range extending close to both supply rails. Operation from a single supply is supported, and split-supply operation is also possible. The open-collector output requires an external pull-up resistor and can be connected to a compatible logic supply when the open-drain node must rise above the comparator supply voltage.

The TS391/TS391A family uses an open-collector output architecture rather than a push-pull output. This allows the output to be pulled up to a selected logic voltage, supports wired-AND behavior with suitable arrangements, and provides a defined state when the output transistor is off. Input bias and offset characteristics determine the practical switching threshold accuracy, while propagation delay determines how quickly the circuit responds to an input crossing.

Typical uses include monitoring sensor outputs, detecting overvoltage or undervoltage conditions, comparing temperature-derived analog signals, and providing a simple control decision in battery-powered products. The SOT-23-5 format supports dense PCB layouts, although engineers should account for the package's limited thermal dissipation and the output pull-up component required by the open-collector architecture.

For reliable operation, use the pin-description table in the manufacturer datasheet when assigning PCB tracks because the comparator uses a specific five-terminal SOT-23 layout. Confirm input voltage, common-mode range, output pull-up voltage, and propagation-delay limits across the complete temperature range before committing the circuit to a safety- or timing-sensitive application.

This product overview consolidates the comparator's electrical limits, package details, replacement constraints, and practical design guidance into one engineering reference. It also distinguishes true pin-compatible alternatives from functionally similar devices with different pin assignments, helping prevent PCB rework and unintended board-level failures.

Alternativas drop-in para TS391ILT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

TS391IYLT

✅ Drop-In
📦 SOT-23-5
Same TS391 family pinout and SOT-23-5 footprint, but a lower temperature grade than TS391ILT; operating-temperature limits differ by 40 °C.

📋 Alternativa de referência (fora do catálogo)

TS391ILT Classificações máximas e características elétricas

Comparator Type Single general-purpose voltage comparator
Supply Voltage Range 2 V to 34 V
Maximum Supply Voltage 36 V
Corrente de alimentação 0.2 mA typical
Maximum Quiescent Current 1.25 mA
Power Consumption 1 mW per comparator at 5 V
Input Offset Voltage ±1 mV typical
Maximum Input Offset Voltage 5 mV at 5 V
Input Offset Current ±5 nA typical
Input Bias Current 25 nA typical
Maximum Input Bias Current 0.25 µA at 5 V
Response Time Approximately 1.3 µs
Alternate Response-Time Listing Approximately 0.3 µs
Tipo de saída Open-collector
Common-Mode Input Range Includes ground and extends close to the positive supply rail
Encapsulamento SOT-23-5, 5 pins
Tipo de montagem SMD surface mount
Status RoHS unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

Configuração de pinos do TS391ILT

SOT-23-5 Package Pinout Diagram SOT-23-5 5-pin surface mount IC, JEDEC MO-178. Pin 1 by dot. 1 2 3 4 5 SOT-23-5
Pino 1 OUT — Open-collector comparator output
Pino 2 IN− — Inverting input
Pino 3 IN+ — Noninverting input
Pino 4 V− — Negative supply or ground connection
Pino 5 V+ — Positive supply connection

Aplicações típicas

TS391ILT é adequado para 6 aplicaçãos: Battery Voltage Monitoring, Industrial Sensor Threshold Detection, Power-Supply Sequencing, Portable Equipment, Temperature and Analog Signal Conditioning, Interface and Level Monitoring.

⚡

Battery Voltage Monitoring

The TS391ILT is appropriate for detecting when a battery-derived supply crosses a defined threshold. Its approximately 0.2 mA typical supply current limits continuous monitoring overhead, while 25 nA typical input-bias current reduces loading on high-impedance divider networks. Place the resistor divider at the noninverting input and reference the threshold at the inverting input. Because the output is open collector, add a pull-up resistor to the required logic level. This device is preferable where low standby consumption matters more than microsecond-scale switching speed.

🏭

Industrial Sensor Threshold Detection

The TS391ILT can translate an analog industrial-sensor signal into a binary decision for a controller input. Its ±1 mV typical input-offset voltage and 25 nA typical input-bias current are useful when preserving the accuracy of a high-impedance sensing node. Connect the sensor signal to one input and a precision reference to the other, then use the open-collector output with an appropriate pull-up. The SOT-23-5 package saves board area, although layout must keep the comparator and reference path away from switching-node noise.

⚡

Power-Supply Sequencing

The TS391ILT can supervise a generated rail and provide an open-collector signal when the monitored voltage changes state. With a resistor divider at the input and a reference at the other input, the comparator supports simple undervoltage or overvoltage indication without a complex controller. Its response time of approximately 1.3 µs is short enough for many sequencing and fault-response paths. The open-collector architecture permits a pull-up to the logic rail used by the supervisor, making the output adaptable to different system voltage domains.

📱

Portable Equipment

The TS391ILT suits portable equipment that must continuously evaluate a slow-changing analog condition without consuming substantial current. Its approximately 1 mW power consumption at 5 V, 25 nA typical input-bias current, and compact SOT-23-5 package help preserve battery life and board area. It can monitor a sensor rail, charger state, or divided battery voltage and report the result through an open-collector logic signal. Select the pull-up supply carefully to avoid backfeeding an unpowered section or exceeding the output ratings.

🔧

Temperature and Analog Signal Conditioning

The TS391ILT can compare a temperature-dependent analog voltage against a stable threshold, producing a clean control signal for a fan, heater, or alarm. Its low input-bias current minimizes disturbance to high-impedance sensor and divider networks, while the open-collector output can directly pull down a suitably rated digital control line. The approximately 0.3 µs to 1.3 µs response specifications cover fast threshold events without requiring a high-speed comparator. Thermal placement and resistor accuracy will determine the practical switching accuracy.

🧩

Interface and Level Monitoring

The TS391ILT is useful for monitoring a logic or interface voltage and asserting an alert when the level becomes invalid. Connect the signal through a divider if it exceeds the common-mode range, compare it with a reference, and use the open-collector output to drive an enable, reset, or fault input through a pull-up. Low typical input-bias current of 25 nA limits disturbance to high-impedance digital buses. The SOT-23-5 footprint simplifies placement beside the monitored circuit, but signal traces should remain short and isolated from high-current switching paths.

Resumo dos produtos recomendados

TS391IYLT Pin-compatible TS391 comparator family option Usado em: Battery Voltage Monitoring, Industrial Sensor Threshold Detection, Power-Supply Sequencing, Portable Equipment, Temperature and Analog Signal Conditioning, Interface and Level Monitoring
What is the TS391ILT?
The TS391ILT is a low-power, single voltage comparator from STMicroelectronics packaged in SOT-23-5. It accepts a 2 V to 34 V single supply, can also operate from split supplies, and provides an open-collector output. According to the STMicroelectronics TS391/TS391A datasheet, the device is intended for low-power threshold and signal-comparison applications.
What is the operating voltage of TS391ILT?
The TS391ILT operates from a 2 V to 34 V single supply, with a 36 V maximum supply rating appearing in catalog data. According to the STMicroelectronics TS391/TS391A datasheet, split-supply operation is also supported. Circuit designers must keep input and output conditions inside the applicable absolute-maximum and common-mode limits.
Where can I download the TS391ILT datasheet PDF?
The official TS391ILT datasheet PDF is available from STMicroelectronics at https://www.st.com/resource/en/datasheet/ts391.pdf. The document covers the TS391 and TS391A low-power single voltage comparator family, including electrical characteristics, pin assignments, typical application information, and package details. Use the manufacturer PDF as the authoritative source for design limits.
What is the TS391ILT pinout?
The TS391ILT uses a five-pin SOT-23 layout with OUT on pin 1, IN− on pin 2, IN+ on pin 3, V− on pin 4, and V+ on pin 5. The manufacturer datasheet confirms the pin assignments. Preserve this orientation in the PCB footprint because pin-compatible replacement must also retain the comparator's input polarity and supply-pin arrangement.
What are the key specifications of TS391ILT that engineers should know?
The TS391ILT is a single 2 V to 34 V comparator with an open-collector output, approximately 1.3 µs response time, ±1 mV typical input-offset voltage, and 25 nA typical input-bias current. Its five-pin SOT-23 package supports compact surface-mount layouts. The STMicroelectronics TS391/TS391A datasheet is the primary source for operating limits and test conditions.
Does the TS391ILT need an output pull-up resistor?
Yes, the TS391ILT open-collector output requires an external pull-up resistor for normal high-level operation. The resistor can be connected to a compatible logic supply when the required high voltage differs from the comparator supply. Its value should be selected from the output sink-current and rise-time constraints shown in the manufacturer datasheet.
Can TS391ILT operate from dual supplies?
The TS391ILT can operate from dual or split supplies in addition to its single-supply configuration. The STMicroelectronics TS391/TS391A datasheet identifies this operating capability and provides the relevant common-mode and supply limits. In a split-supply design, keep the input voltages and pulled-up output within the limits for the selected supply arrangement.
What can replace TS391ILT?
The only directly supported replacement identified from the manufacturer family is TS391IYLT, which retains the SOT-23-5 footprint and TS391 pin arrangement while using a different temperature grade. The STMicroelectronics TS391/TS391A datasheet establishes the family relationship. Any other device must be checked carefully because functionally similar comparators may use a different pinout.
Can TS391IYLT replace TS391ILT without changing the PCB?
TS391IYLT is the closest pin-compatible option identified for TS391ILT because it uses the same SOT-23-5 footprint and TS391 family pin arrangement. The primary selection difference is the temperature grade, so it is suitable as a drop-in option only where its rated operating temperature covers the application. Confirm all electrical limits before substitution.
Is TLV331 a pin-to-pin replacement for TS391ILT?
No, TLV331 is functionally similar but not a direct pin-to-pin replacement for TS391ILT. Texas Instruments states that the TS391ILT uses a northwest pin arrangement with reversed inputs and that no direct replacement was available for that pinout in its response. Functionally equivalent comparators therefore require different routing or a revised PCB footprint.
When should I choose TS391ILT over a higher-speed comparator?
Choose TS391ILT when a low-power, general-purpose threshold decision is more important than minimum propagation delay. Its approximately 0.2 mA typical supply current and ±1 mV typical input-offset voltage suit continuous monitoring and low-power sensing. Choose a faster comparator only when the application genuinely requires sub-microsecond response timing.
Is TS391ILT suitable for battery and industrial sensor monitoring?
The TS391ILT is suitable for low-power sensor-monitoring and battery-powered threshold circuits because its typical supply current is approximately 0.2 mA and its input-bias current is 25 nA typical. The open-collector output supports flexible pull-up arrangements. Verify the common-mode range at the actual battery voltage and ensure the output pull-up does not exceed the device limits.
What is the lead time for TS391ILT?
Current lead time and minimum order quantity should be requested through the Request a Quote form on this page. The manufacturer product page and authorized ordering channels indicate that TS391ILT is currently offered, but a contractual delivery schedule depends on order quantity, package format, and production availability. The form is the appropriate route for a current production commitment.
Where can I buy TS391ILT online?
Use the Request a Quote form on this page to request TS391ILT availability, current commercial terms, and a production lead time. The manufacturer offers the TS391ILT through its direct ordering channel, and distributor inventory can vary by package and region. Providing the required quantity and target assembly location allows the most relevant fulfillment option to be quoted.
Is TS391ILT currently in stock and what does it cost?
Current stock and commercial terms for TS391ILT should be confirmed through the Request a Quote form on this page because distributor availability changes by package and order quantity. The manufacturer product page identifies the part as orderable, while inventory levels at individual distributors may differ. Submit the required quantity for an availability confirmation and quotation.
TS391ILT vs TS391IYLT — which is better for an industrial design?
TS391ILT and TS391IYLT share the TS391 comparator architecture, SOT-23-5 package, and pin arrangement, but they differ in temperature grade. Select TS391ILT for designs requiring its higher temperature capability and select TS391IYLT where its lower temperature range is sufficient. Both require an open-collector pull-up and confirmation of input, output, and common-mode limits.

Dados de referência de engenharia para TS391ILT — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose TS391ILT for low-power threshold detection, battery monitoring, power-supply supervision, and industrial sensor interfaces where the full commercial temperature range is required. Its 2 V to 34 V supply capability, approximately 0.2 mA typical supply current, and open-collector output make it suitable for mixed analog and logic systems. Choose TS391IYLT when the same footprint, pinout, and electrical architecture are required but the lower temperature grade is sufficient. Do not select TLV331 as a direct drop-in part because its pin arrangement differs; it is only a functional alternative if the PCB is redesigned. In every case, confirm the input common-mode range, output pull-up voltage, sink current, and propagation-delay requirement.

Comparação com alternativas

Parâmetro Este produto TS391IYLT
Brand STMicroelectronics STMicroelectronics
Package SOT-23-5, 5 pins SOT-23-5, 5 pins - same
Comparator Configuration Single voltage comparator Single voltage comparator
Supply Voltage Range 2 V to 34 V 2 V to 34 V
Supply Current 0.2 mA typical 0.2 mA typical
Input Offset Voltage ±1 mV typical ±1 mV typical
Input Bias Current 25 nA typical 25 nA typical
Output Type Open collector Open collector
Response Time Approximately 1.3 µs Approximately 1.3 µs

Principais diferenciais

  • Maintains the TS391-specific input arrangement (vs TLV331)
  • Lower typical power consumption for continuous monitoring (vs TS391IYLT)
  • Wide single-supply operating range (vs TS391IYLT)

Notas de projeto

Do not treat TLV331 or another low-power comparator as a direct replacement merely because its specifications appear similar. The TS391ILT has a northwest SOT-23-5 pin arrangement with reversed inputs, so changing comparator families can place OUT, an input, or a supply pin on the wrong PCB node. TS391IYLT is the identified same-footprint family alternative; otherwise, redesign the footprint and revalidate the routing.

The open-collector output needs an external pull-up resistor. Choose its resistance from the output sink-current limit, required logic rise time, and available output capacitance, using the characteristic curves in the STMicroelectronics TS391/TS391A datasheet. The pull-up may connect to a compatible logic supply, but do not exceed the device's maximum output or absolute-maximum voltage ratings.

Place the input resistors and any reference close to the comparator to minimize parasitic pickup and comparator propagation delay. Route the two inputs away from switching nodes and keep the open-collector output trace short enough to avoid unwanted coupling. Respect the SOT-23-5 land pattern and confirm pin 1 orientation because pin 2 and pin 3 correspond to the inverting and noninverting inputs in the TS391 northwest arrangement.

The TS391ILT is a low-power analog IC rather than a discrete power transistor, so SOA data is not applicable. Its principal thermal concerns are the SOT-23-5 copper area and the local temperature around the comparator. Keep the device away from heat-generating components, provide adequate board copper, and verify that the chosen package temperature grade covers the maximum ambient and self-heating conditions.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The manufacturer datasheet and product page do not state the requested environmental-compliance fields for this exact ordering code, so each unconfirmed field remains unknown.

Dados verificados em: 2026-11-16 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

ts391ilt datasheet TS391ILT specifications TS391ILT pinout TS391ILT datasheet pdf STMicroelectronics TS391ILT TS391ILT SOT-23-5 footprint TS391ILT equivalent TS391ILT drop-in replacement TS391ILT vs TS391IYLT TS391ILT application circuit TS391ILT price TS391ILT stock

Componentes & termos relacionados

STMicroelectronics TS391ILT TS391IYLT TS391A voltage comparator analog comparator single comparator open-collector output open-drain output low-power IC semiconductor SOT-23-5 SOT-23 package family surface mount SMD input offset voltage input bias current supply current response time common-mode input voltage range battery monitoring industrial sensor monitoring power-supply sequencing
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ