TS922IPT - Dual Rail-to-Rail 4 MHz Op Amp | STMicroelectronics
N.º da peça: TS922IPT ✓ AtivoTS922IPT Visão geral
An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its two inputs while providing high input impedance, low output impedance, and stable operation around a feedback-defined voltage. The TS922 belongs to the operational-amplifier hierarchy, where a dual BiCMOS amplifier combines bipolar input characteristics with CMOS-compatible output drive for low-power mixed-signal systems.
The TS922IPT's rail-to-rail inputs allow sensing signals close to either supply rail, while rail-to-rail outputs improve dynamic range in single-supply circuits. Its high output-current capability is intended for driving relatively low-impedance loads. Low distortion of 0.005% and very low noise make the amplifier useful in audio and other precision analog paths. The dual configuration also reduces component count when two independent gain stages are required.
STMicroelectronics identifies the TS922 family as a BiCMOS dual operational amplifier optimized for 3 V and 5 V operation. The 4 MHz gain-bandwidth product supports moderate-bandwidth signal conditioning, including active filtering, sensor amplification, and audio stages. The 1.3 V/us slew rate improves large-signal response, although higher-frequency designs should verify stability, load capacitance, and noise-gain requirements.
Typical uses include audio preamplification, low-load-impedance driver stages, sensor interfaces, active filters, and portable 3 V or 5 V equipment. It is particularly relevant when dual-channel signal conditioning is needed without introducing rail-to-rail input/output limitations common in older amplifier families.
PCB design should keep input and feedback paths short, place compensation or filtering capacitors close to their associated pins, and maintain a solid ground reference. Decoupling capacitors should be connected to the supply and ground pins with minimal loop area. Designers should also verify output swing and capacitive-load stability against the circuit's load current and impedance.
This product page combines manufacturer specifications, exact drop-in candidate screening, application guidance, pin assignments, and a practical comparison framework. It helps engineers distinguish electrically different family variants from mechanically compatible alternatives before approving a PCB substitution.
Alternativas drop-in para TS922IPT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
TS922AIPT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TS922AIYPT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TS922IYPT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TS922IPT Classificações máximas e características elétricas
| Number of Amplifier Channels | 2 channels |
| Amplifier Type | Dual BiCMOS operational amplifier |
| Input Type | Rail-to-rail input |
| Tipo de saída | Rail-to-rail output |
| Supply Voltage Range | 2.7 V to 12 V |
| Optimized Supply Voltage | 3 V and 5 V |
| Gain-Bandwidth Product | 4 MHz |
| Slew Rate | 1.3 V/us |
| Low Distortion | 0.005% |
| Output Drive | High output current for low-load-impedance drive |
| Encapsulamento | 8-pin TSSOP |
| Tipo de montagem | Surface mount |
| General-Purpose Classification | Standard general-purpose amplifier |
Configuração de pinos do TS922IPT
| Pino 1 | OUT1 — Output of amplifier channel 1 |
| Pino 2 | IN1- — Inverting input of amplifier channel 1 |
| Pino 3 | IN1+ — Non-inverting input of amplifier channel 1 |
| Pino 4 | V- — Negative supply voltage |
| Pino 5 | IN2+ — Non-inverting input of amplifier channel 2 |
| Pino 6 | IN2- — Inverting input of amplifier channel 2 |
| Pino 7 | OUT2 — Output of amplifier channel 2 |
| Pino 8 | V+ — Positive supply voltage |
Aplicações típicas
TS922IPT é adequado para 6 aplicaçãos: Low-Power Audio Preamplifier, Sensor Signal Conditioning, Active Audio Filter, Low-Impedance Output Driver, Portable Instrumentation Front End, Mixed-Signal Buffering.
Low-Power Audio Preamplifier
The TS922IPT fits dual audio preamplifier channels operating from 3 V or 5 V because its rail-to-rail input stage accepts signals near the supply rails and its rail-to-rail output improves usable signal range. According to the STMicroelectronics manufacturer datasheet, the amplifier combines 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and 0.005% distortion. Use each channel with its own feedback network and decouple the 8-pin TSSOP supply pins close to the package. Confirm output swing into the audio load and verify stability with any additional capacitance introduced by the audio stage.
Recomendado
Sensor Signal Conditioning
The TS922IPT is useful for amplifying sensor outputs in portable 3 V and 5 V equipment because the rail-to-rail input stage reduces common-mode-range constraints. Its 4 MHz gain-bandwidth product provides adequate bandwidth for many temperature, pressure, and position sensors, while dual construction supports two independent channels. Place the sensor input directly at the amplifier input and route feedback components away from switching and digital traces. According to the STMicroelectronics manufacturer datasheet, the BiCMOS implementation also provides high output-current capability for driving the following analog or mixed-signal stage.
Recomendado
Active Audio Filter
The TS922IPT can implement dual active-filter sections where a 4 MHz gain-bandwidth product is sufficient for the operating band. Rail-to-rail input and output stages improve signal swing in single-supply filters, while the 1.3 V/us slew rate supports moderate-amplitude and moderate-frequency waveforms. According to the STMicroelectronics manufacturer datasheet, the device is optimized for 3 V and 5 V operation. Keep the resistor and capacitor network close to the corresponding input and output pins, use matched components for predictable filter response, and verify closed-loop stability against the gain and phase response of the selected feedback topology.
Recomendado
Low-Impedance Output Driver
The TS922IPT is appropriate for driving a relatively low load impedance because STMicroelectronics identifies high output current as a defining characteristic of the TS922 family. The dual channels can each drive an audio, communications, or transducer interface while operating from 3 V or 5 V. According to the STMicroelectronics manufacturer datasheet, the rail-to-rail output supports efficient use of the available supply range. Validate the exact output-current limit, output-swing margin, thermal behavior, and capacitive-load stability for the connected load before production release.
Recomendado
Portable Instrumentation Front End
The TS922IPT suits two-channel portable instrumentation because its 4 MHz bandwidth handles moderate-frequency conditioning while its low distortion supports accurate signal reproduction. Rail-to-rail inputs are valuable when a sensor or converter operates near the lower supply rail, and the 8-pin TSSOP package supports compact PCB construction. According to the STMicroelectronics manufacturer datasheet, the device is fully specified for 3 V and 5 V operation. Use a quiet reference supply, place bypass capacitors beside the supply pins, and check input offset and noise requirements against the instrumentation accuracy budget.
Recomendado
Mixed-Signal Buffering
The TS922IPT can buffer ADC drivers, DAC outputs, or comparator interfaces in compact mixed-signal systems. Its rail-to-rail input and output characteristics reduce signal-headroom constraints, while 4 MHz bandwidth and 1.3 V/us slew rate provide adequate response for many moderate-speed data-acquisition paths. According to the STMicroelectronics manufacturer datasheet, the device also maintains low distortion. Keep sensitive analog nodes away from digital return currents, use a continuous ground reference, and verify that the selected closed-loop gain remains stable with the sampling network and routing capacitance attached.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TS922IPT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TS922AIPT | TS922AIYPT | TS922IYPT |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP |
| Amplifier Configuration | Dual | Dual | Dual | Dual |
| Process Technology | BiCMOS | BiCMOS | BiCMOS | BiCMOS |
| Supply Voltage Range | 2.7 V to 12 V | 2.7 V to 12 V | 2.7 V to 12 V | 2.7 V to 12 V |
| Gain-Bandwidth Product | 4 MHz | 4 MHz | 4 MHz | 4 MHz |
| Slew Rate | 1.3 V/us | 1.3 V/us | 1.3 V/us | 1.3 V/us |
| Input Configuration | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input |
Principais diferenciais
- High output-current capability within a dual TSSOP amplifier (vs TS922AIPT)
- Defined low-distortion performance (vs TS922AIYPT)
- Rail-to-rail dual-channel operation from 3 V and 5 V rails (vs TS922IYPT)
Notas de projeto
Place the supply bypass capacitor immediately between pins 8 and 4, with both connections short and the ground return following the device ground rather than cutting across analog signal paths. Keep amplifier inputs, feedback resistors, and high-impedance nodes away from switching nodes and fast digital traces. A compact decoupling loop reduces supply impedance and prevents digital or RF activity from modulating the analog rails.
Do not treat rail-to-rail input as permission for input voltages outside the supply limits. Verify the exact input common-mode range, output swing, and maximum supply voltage at the highest operating temperature. For low-resistance loads, check output-current capability and thermal rise rather than assuming that a 4 MHz amplifier can drive every downstream stage without distortion.
Account for parasitic capacitance added by PCB traces, sockets, probes, and downstream loads when configuring high-gain stages. According to the STMicroelectronics manufacturer datasheet, the TS922 family supports rail-to-rail operation, but stable closed-loop behavior still depends on the selected feedback network. Use short feedback traces and confirm stability at the intended gain, temperature, supply, and load conditions before production release.
Estimate amplifier dissipation from the actual output voltage, output current, and supply voltage, then add quiescent power. The 8-pin TSSOP is compact, so sustained dissipation into a low-impedance load can raise junction temperature even when the average signal current appears modest. Validate worst-case load, supply, and ambient conditions and provide adequate copper area around the TSSOP footprint.
Informações de conformidade
The available manufacturer and distributor pages do not state the requested environmental and material-compliance statuses. AEC-Q100 is not applicable because TS922IPT is a general-purpose operational amplifier rather than an automotive-qualified device.