STMicroelectronics

TS922IPT - Dual Rail-to-Rail 4 MHz Op Amp | STMicroelectronics

料号: TS922IPT ✓ 量产中
2.7 V to 12 V Vdss 8-pin TSSOP Package
最小起订量: 1 |

TS922IPT 概述

STMicroelectronics TS922IPT is a dual rail-to-rail input and output BiCMOS operational amplifier rated for 2.7 V to 12 V operation. It provides two amplifier channels, 4 MHz gain-bandwidth performance, a 1.3 V/us slew rate, and rail-to-rail input and output stages in an 8-pin TSSOP package. The device is optimized and fully specified for 3 V and 5 V systems.

An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its two inputs while providing high input impedance, low output impedance, and stable operation around a feedback-defined voltage. The TS922 belongs to the operational-amplifier hierarchy, where a dual BiCMOS amplifier combines bipolar input characteristics with CMOS-compatible output drive for low-power mixed-signal systems.

The TS922IPT's rail-to-rail inputs allow sensing signals close to either supply rail, while rail-to-rail outputs improve dynamic range in single-supply circuits. Its high output-current capability is intended for driving relatively low-impedance loads. Low distortion of 0.005% and very low noise make the amplifier useful in audio and other precision analog paths. The dual configuration also reduces component count when two independent gain stages are required.

STMicroelectronics identifies the TS922 family as a BiCMOS dual operational amplifier optimized for 3 V and 5 V operation. The 4 MHz gain-bandwidth product supports moderate-bandwidth signal conditioning, including active filtering, sensor amplification, and audio stages. The 1.3 V/us slew rate improves large-signal response, although higher-frequency designs should verify stability, load capacitance, and noise-gain requirements.

Typical uses include audio preamplification, low-load-impedance driver stages, sensor interfaces, active filters, and portable 3 V or 5 V equipment. It is particularly relevant when dual-channel signal conditioning is needed without introducing rail-to-rail input/output limitations common in older amplifier families.

PCB design should keep input and feedback paths short, place compensation or filtering capacitors close to their associated pins, and maintain a solid ground reference. Decoupling capacitors should be connected to the supply and ground pins with minimal loop area. Designers should also verify output swing and capacitive-load stability against the circuit's load current and impedance.

This product page combines manufacturer specifications, exact drop-in candidate screening, application guidance, pin assignments, and a practical comparison framework. It helps engineers distinguish electrically different family variants from mechanically compatible alternatives before approving a PCB substitution.

直接替换替代料: TS922IPT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

TS922AIPT

✅ 直接替换
📦 8-pin TSSOP
The 4 MHz gain-bandwidth product and 2.7 V to 12 V supply range remain within 0% of the stated TS922IPT values, while the TS922A electrical characterization differs and must be checked

📋 参考替代料(不在目录中)

TS922AIYPT

✅ 直接替换
📦 8-pin TSSOP
The 4 MHz gain-bandwidth product and 2.7 V to 12 V supply range are unchanged by 0%, with the device identified as an industrial-grade TS922A family variant

📋 参考替代料(不在目录中)

TS922IYPT

✅ 直接替换
📦 8-pin TSSOP
The 4 MHz gain-bandwidth product and 2.7 V to 12 V supply range remain within 0% of TS922IPT, with a different industrial-grade ordering variant

📋 参考替代料(不在目录中)

TS922IPT 最大额定值与电气特性

Number of Amplifier Channels 2 channels
Amplifier Type Dual BiCMOS operational amplifier
Input Type Rail-to-rail input
输出类型 Rail-to-rail output
Supply Voltage Range 2.7 V to 12 V
Optimized Supply Voltage 3 V and 5 V
Gain-Bandwidth Product 4 MHz
Slew Rate 1.3 V/us
Low Distortion 0.005%
Output Drive High output current for low-load-impedance drive
封装 8-pin TSSOP
安装类型 Surface mount
General-Purpose Classification Standard general-purpose amplifier

TS922IPT 引脚配置

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
引脚 1 OUT1 — Output of amplifier channel 1
引脚 2 IN1- — Inverting input of amplifier channel 1
引脚 3 IN1+ — Non-inverting input of amplifier channel 1
引脚 4 V- — Negative supply voltage
引脚 5 IN2+ — Non-inverting input of amplifier channel 2
引脚 6 IN2- — Inverting input of amplifier channel 2
引脚 7 OUT2 — Output of amplifier channel 2
引脚 8 V+ — Positive supply voltage

典型应用

TS922IPT 适用于 6 应用s: Low-Power Audio Preamplifier, Sensor Signal Conditioning, Active Audio Filter, Low-Impedance Output Driver, Portable Instrumentation Front End, Mixed-Signal Buffering.

🎧

Low-Power Audio Preamplifier

The TS922IPT fits dual audio preamplifier channels operating from 3 V or 5 V because its rail-to-rail input stage accepts signals near the supply rails and its rail-to-rail output improves usable signal range. According to the STMicroelectronics manufacturer datasheet, the amplifier combines 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and 0.005% distortion. Use each channel with its own feedback network and decouple the 8-pin TSSOP supply pins close to the package. Confirm output swing into the audio load and verify stability with any additional capacitance introduced by the audio stage.

🧩

Sensor Signal Conditioning

The TS922IPT is useful for amplifying sensor outputs in portable 3 V and 5 V equipment because the rail-to-rail input stage reduces common-mode-range constraints. Its 4 MHz gain-bandwidth product provides adequate bandwidth for many temperature, pressure, and position sensors, while dual construction supports two independent channels. Place the sensor input directly at the amplifier input and route feedback components away from switching and digital traces. According to the STMicroelectronics manufacturer datasheet, the BiCMOS implementation also provides high output-current capability for driving the following analog or mixed-signal stage.

🔧

Active Audio Filter

The TS922IPT can implement dual active-filter sections where a 4 MHz gain-bandwidth product is sufficient for the operating band. Rail-to-rail input and output stages improve signal swing in single-supply filters, while the 1.3 V/us slew rate supports moderate-amplitude and moderate-frequency waveforms. According to the STMicroelectronics manufacturer datasheet, the device is optimized for 3 V and 5 V operation. Keep the resistor and capacitor network close to the corresponding input and output pins, use matched components for predictable filter response, and verify closed-loop stability against the gain and phase response of the selected feedback topology.

🌐

Low-Impedance Output Driver

The TS922IPT is appropriate for driving a relatively low load impedance because STMicroelectronics identifies high output current as a defining characteristic of the TS922 family. The dual channels can each drive an audio, communications, or transducer interface while operating from 3 V or 5 V. According to the STMicroelectronics manufacturer datasheet, the rail-to-rail output supports efficient use of the available supply range. Validate the exact output-current limit, output-swing margin, thermal behavior, and capacitive-load stability for the connected load before production release.

📱

Portable Instrumentation Front End

The TS922IPT suits two-channel portable instrumentation because its 4 MHz bandwidth handles moderate-frequency conditioning while its low distortion supports accurate signal reproduction. Rail-to-rail inputs are valuable when a sensor or converter operates near the lower supply rail, and the 8-pin TSSOP package supports compact PCB construction. According to the STMicroelectronics manufacturer datasheet, the device is fully specified for 3 V and 5 V operation. Use a quiet reference supply, place bypass capacitors beside the supply pins, and check input offset and noise requirements against the instrumentation accuracy budget.

🖥️

Mixed-Signal Buffering

The TS922IPT can buffer ADC drivers, DAC outputs, or comparator interfaces in compact mixed-signal systems. Its rail-to-rail input and output characteristics reduce signal-headroom constraints, while 4 MHz bandwidth and 1.3 V/us slew rate provide adequate response for many moderate-speed data-acquisition paths. According to the STMicroelectronics manufacturer datasheet, the device also maintains low distortion. Keep sensitive analog nodes away from digital return currents, use a continuous ground reference, and verify that the selected closed-loop gain remains stable with the sampling network and routing capacitance attached.

What is the operating voltage of TS922IPT?
The STMicroelectronics TS922IPT operates from 2.7 V to 12 V and is optimized for 3 V and 5 V equipment. According to the STMicroelectronics manufacturer datasheet, its rail-to-rail input and output stages remain useful in single-supply designs where signals may approach either supply rail. Designers should maintain the documented supply limits and verify output swing under the intended load and temperature conditions.
What are the key specifications of TS922IPT that engineers should know?
The TS922IPT is a dual BiCMOS operational amplifier with 4 MHz gain-bandwidth product, 1.3 V/us slew rate, rail-to-rail inputs and outputs, and a 2.7 V to 12 V supply range. According to the STMicroelectronics manufacturer datasheet, the device also provides high output-current capability and 0.005% low distortion. It is packaged in an 8-pin TSSOP for surface-mounted dual-channel analog designs.
Where can I download the TS922IPT datasheet PDF?
The official TS922IPT datasheet PDF is available from STMicroelectronics at https://www.st.com/resource/en/datasheet/ts922.pdf. The document covers the TS922 and TS922A dual operational amplifiers and is the preferred source for pin assignments, electrical characteristics, test conditions, and application guidance. Use the ordering-information table to confirm that TS922IPT corresponds to the 8-pin TSSOP tape-and-reel configuration.
Where can I find the TS922IPT pinout?
The TS922IPT pinout is documented in the STMicroelectronics manufacturer datasheet and corresponds to an 8-pin TSSOP: outputs occupy pins 1 and 7, the four input pins are 2, 3, 5, and 6, the supply pins are 8 and 4, and no external connection is required between pins 2 and 3 for ordinary dual-amplifier use. Check the package drawing and pin table before assigning PCB nets.
Is TS922IPT suitable for 3 V and 5 V applications?
Yes, the TS922IPT is explicitly optimized and fully specified for 3 V and 5 V operation. According to the STMicroelectronics manufacturer datasheet, its BiCMOS architecture provides rail-to-rail input and output behavior plus high output-current capability. It is well suited to portable audio, sensor-conditioning, filtering, and low-impedance driver circuits that operate from these common supply voltages.
What can replace TS922IPT?
The TS922AIPT and TS922AIYPT are the closest same-manufacturer TSSOP candidates identified for TS922IPT, while the TS922IYPT is another industrial-grade family member. According to STMicroelectronics family documentation, all retain the dual rail-to-rail BiCMOS architecture and 4 MHz class. Confirm the exact electrical limits, temperature grade, pin table, and stability requirements before using any replacement without a design review.
Is TS922IPT the same as TS922AIPT?
No, TS922IPT and TS922AIPT belong to related but distinct TS922 device variants, so they should not be treated as automatically identical. According to the STMicroelectronics manufacturer datasheet, both use the rail-to-rail dual BiCMOS architecture, but the ordering code identifies different device versions. Review the comparison tables for offset, noise, distortion, output-current, and temperature limits before substituting TS922AIPT for TS922IPT.
Can TS922IYPT replace TS922IPT?
The TS922IYPT is a mechanically compatible same-family candidate, but it is not automatically an unconditional replacement. According to the STMicroelectronics manufacturer datasheet family information, it remains a dual 4 MHz rail-to-rail BiCMOS operational amplifier in the relevant TSSOP family. Verify its temperature grade, electrical characteristics, and marking rules against the exact requirements of the original circuit.
What is the best STMicroelectronics equivalent for TS922IPT?
The TS922AIPT is the closest same-manufacturer TSSOP equivalent identified for TS922IPT because it remains within the TS922 dual rail-to-rail BiCMOS family and retains the 4 MHz operating class. According to the STMicroelectronics manufacturer datasheet, however, the TS922 and TS922A versions have distinct characterization tables. Use the alternative only after checking offset, noise, distortion, output drive, and temperature requirements.
What is the best Texas Instruments equivalent for TS922IPT?
The TLV2442CPWR is a functionally related dual rail-to-rail amplifier, but it is not a confirmed drop-in replacement for TS922IPT because it uses a VSSOP-8 package rather than the specified TSSOP-8 footprint. The functional differences and package mismatch require PCB review. According to the STMicroelectronics manufacturer datasheet, TS922IPT specifically emphasizes high output-current drive for low-load impedances.
When should I choose TS922IPT over a TS922A-series device?
Choose TS922IPT when the original circuit was designed around the specified TS922 electrical limits and requires an 8-pin TSSOP dual amplifier with 2.7 V to 12 V operation. According to the STMicroelectronics manufacturer datasheet, TS922 devices provide rail-to-rail input and output stages and high output-current capability. Select a TS922A-series candidate only after a direct comparison confirms that its characterization satisfies the application's offset, noise, distortion, and temperature requirements.
Where to buy TS922IPT online?
Use the Request a Quote form on this page to request TS922IPT availability, current lead time, and minimum order quantity. The part is listed as an STMicroelectronics 8-pin TSSOP dual operational amplifier, and the ordering code TS922IPT identifies the tape-and-reel package. Confirm the exact suffix, delivery packaging, and required quantity when submitting the request.
What is the price of TS922IPT?
The current price of TS922IPT should be obtained through the Request a Quote form on this page. The form lets buyers request current pricing and availability for the exact TS922IPT ordering code without relying on stale figures. Include the required order quantity and intended packaging so the quote can reflect the correct manufacturing and shipment configuration.
What is the lead time for TS922IPT?
Request the current TS922IPT lead time through the Request a Quote form on this page. The exact manufacturing schedule can depend on order quantity, packaging, and current factory conditions. The ordering information identifies TS922IPT as the 8-pin TSSOP tape-and-reel version, so include that complete suffix in the request to avoid ambiguity.
Is TS922IPT in stock?
Current TS922IPT stock status should be confirmed through the Request a Quote form on this page. Supply availability can change with demand and order quantity, so an inventory confirmation tied to the exact 8-pin TSSOP tape-and-reel ordering code is preferable to assuming availability. Submit the required quantity and project schedule with the quote request.

工程参考数据: TS922IPT ——对比、设计指导和合规信息。

选型指南

Choose TS922IPT when the circuit requires a dual rail-to-rail BiCMOS amplifier in an 8-pin TSSOP, operates from 3 V or 5 V, and needs the combination of 4 MHz bandwidth, 1.3 V/us slew rate, low distortion, and high output-current drive. TS922AIPT and TS922AIYPT are viable same-family alternatives when their offset, noise, distortion, and output-drive characteristics satisfy the design, but the TS922A version should not be treated as an automatic substitute. TS922IYPT is useful when its industrial-grade ordering characteristics are preferred and the complete electrical table remains acceptable. Avoid mechanically similar dual amplifiers in different package widths unless the PCB can be redesigned. For every candidate, verify supply range, input common-mode range, output swing, load drive, thermal margin, noise, offset, distortion, and closed-loop stability.

与替代料对比

参数 本产品 TS922AIPT TS922AIYPT TS922IYPT
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics
Package 8-pin TSSOP 8-pin TSSOP 8-pin TSSOP 8-pin TSSOP
Amplifier Configuration Dual Dual Dual Dual
Process Technology BiCMOS BiCMOS BiCMOS BiCMOS
Supply Voltage Range 2.7 V to 12 V 2.7 V to 12 V 2.7 V to 12 V 2.7 V to 12 V
Gain-Bandwidth Product 4 MHz 4 MHz 4 MHz 4 MHz
Slew Rate 1.3 V/us 1.3 V/us 1.3 V/us 1.3 V/us
Input Configuration Rail-to-rail input Rail-to-rail input Rail-to-rail input Rail-to-rail input

关键差异点

  • High output-current capability within a dual TSSOP amplifier (对比 TS922AIPT)
  • Defined low-distortion performance (对比 TS922AIYPT)
  • Rail-to-rail dual-channel operation from 3 V and 5 V rails (对比 TS922IYPT)

设计说明

Place the supply bypass capacitor immediately between pins 8 and 4, with both connections short and the ground return following the device ground rather than cutting across analog signal paths. Keep amplifier inputs, feedback resistors, and high-impedance nodes away from switching nodes and fast digital traces. A compact decoupling loop reduces supply impedance and prevents digital or RF activity from modulating the analog rails.

Do not treat rail-to-rail input as permission for input voltages outside the supply limits. Verify the exact input common-mode range, output swing, and maximum supply voltage at the highest operating temperature. For low-resistance loads, check output-current capability and thermal rise rather than assuming that a 4 MHz amplifier can drive every downstream stage without distortion.

Account for parasitic capacitance added by PCB traces, sockets, probes, and downstream loads when configuring high-gain stages. According to the STMicroelectronics manufacturer datasheet, the TS922 family supports rail-to-rail operation, but stable closed-loop behavior still depends on the selected feedback network. Use short feedback traces and confirm stability at the intended gain, temperature, supply, and load conditions before production release.

Estimate amplifier dissipation from the actual output voltage, output current, and supply voltage, then add quiescent power. The 8-pin TSSOP is compact, so sustained dissipation into a low-impedance load can raise junction temperature even when the average signal current appears modest. Validate worst-case load, supply, and ambient conditions and provide adequate copper area around the TSSOP footprint.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The available manufacturer and distributor pages do not state the requested environmental and material-compliance statuses. AEC-Q100 is not applicable because TS922IPT is a general-purpose operational amplifier rather than an automotive-qualified device.

数据核验日期: 2026-11-10 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

TS922IPT datasheet TS922IPT datasheet pdf TS922IPT pinout TS922IPT specifications TS922IPT TSSOP-8 STMicroelectronics TS922IPT TS922IPT equivalent TS922IPT replacement TS922IPT vs TS922AIPT TS922IPT price TS922IPT stock TS922IPT rail to rail op amp

相关元器件 & 术语

STMicroelectronics TS922IPT TS922 TS922A TS922AIPT TS922AIYPT TS922IYPT dual operational amplifier BiCMOS operational amplifier rail-to-rail input rail-to-rail output gain-bandwidth product slew rate output current signal conditioning audio preamplifier active filter TSSOP-8 TSSOP package family surface-mount package low-noise electronics 3 V power supply 5 V power supply
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情