TS942BID - Dual Rail-to-Rail Micropower Op Amp | STMicroelectronics
N.º da peça: TS942BID ✓ AtivoTS942BID Visão geral
An operational amplifier is a high-gain analog building block that compares two input voltages and amplifies their difference. Within the broader semiconductor hierarchy, the TS942BID belongs to the operational-amplifier category, then analog amplifier ICs, and finally integrated circuits. Rail-to-rail output capability permits the output to approach the positive and negative supply limits under suitable load and output-voltage conditions, making the device useful in low-voltage sensor, portable-instrumentation, and battery-powered signal chains.
The device uses a 2.5 V minimum operating supply and supports supplies up to 10 V. Its typical gain-bandwidth product is 60 dB, while its typical output current capability is 5 mA per channel. The low-power operating characteristics are reflected in a quoted supply current of 1.2 µA per channel, and the offset-related listing identifies approximately 0.00015 µA, or 150 nA, of input bias current. These characteristics make the TS942BID appropriate for applications in which amplifier power can dominate the total system budget.
The TS942BID contains two amplifier channels in one compact 8-SO package. Its standard general-purpose classification and rail-to-rail architecture make it suitable for signal conditioning, low-level amplification, and buffer stages. Designers should still account for the finite gain-bandwidth product when operating at higher closed-loop gains, because bandwidth reduces as the noise gain rises. Input common-mode range, output swing, offset voltage, noise density, and slew rate should be confirmed from the manufacturer datasheet before precision or high-speed signal-chain use.
Typical application areas include portable sensor interfaces, low-power instrumentation, battery-operated measurement systems, and general analog signal conditioning. In a sensor interface, the TS942BID can amplify a low-level sensor output while keeping channel current consumption small. In an instrumentation block, its dual-channel configuration can reduce component count when two related signals must be conditioned. As a buffer, it can isolate a higher-impedance source from a downstream analog stage while maintaining a compact eight-pin footprint.
Layout and stability remain important in micropower designs. Place input and feedback components close to their associated pins, keep sensitive input traces away from switching nodes, and avoid long high-impedance traces that can increase leakage and noise pickup. Select passive feedback values that account for the amplifier’s gain-bandwidth limit, and verify operation across the full 2.5 V to 10 V supply range. The manufacturer datasheet should be used for the final pin assignment, typical characteristics, absolute maximum ratings, and application-circuit details.
This product summary combines the manufacturer’s device description with practical guidance for package reuse, analog layout, low-power selection, and replacement evaluation. It also distinguishes verified drop-in interchangeability from merely similar amplifier functions, helping engineers avoid PCB rework and unexpected bias, bandwidth, or supply-voltage differences.
Alternativas drop-in para TS942BID — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasTS942BID Classificações máximas e características elétricas
| Amplifier Type | Rail-to-rail output micropower operational amplifier |
| Number of Circuits | 2 circuits |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2.5 V to 10 V |
| Gain-Bandwidth Product | 60 dB |
| Output Current per Channel | 5 mA |
| Supply Current per Channel | 1.2 µA |
| Input Bias Current | 0.00015 µA |
| Faixa de temperatura de operação | -40°C to +85°C |
| Encapsulamento | 8-SOIC, 0.154 inch, 3.90 mm width |
| Contagem de pinos | 8 pins |
| Tipo de montagem | Surface mount |
| Tipo de saída | Rail-to-rail |
| Application Classification | General purpose |
Guia de Configuração de Pinos do TS942BID 8-soic, 0.154 inch, 3.90 mm width
Configuração de pinos para TS942BID (pacote 8-soic, 0.154 inch, 3.90 mm width). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para TS942BID.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
TS942BID é adequado para 6 aplicaçãos: Battery-Powered Sensor Signal Conditioning, Portable Instrumentation, Low-Power Voltage Buffer, Industrial Low-Level Amplification, Medical Monitor Front End, Audio and Environmental Monitoring.
Battery-Powered Sensor Signal Conditioning
The TS942BID fits low-energy sensor interfaces because its approximately 1.2 µA supply current per channel limits amplifier overhead when the source impedance is moderate. The dual configuration can amplify or buffer two related sensor outputs without occupying two separate packages. Its 2.5 V minimum supply supports compact systems powered from a regulated low-voltage source, while the 60 dB gain-bandwidth product is suitable for slowly changing sensor signals. The practical constraint is closed-loop bandwidth: higher gain reduces the available bandwidth, so verify settling time and signal bandwidth against the 60 dB gain-bandwidth product.
Recomendado
Portable Instrumentation
The TS942BID is appropriate for portable instrumentation that must combine compactness with low amplifier power consumption. Two channels in the 8-SOIC package can handle differential or independent analog channels, reducing board area compared with two discrete single amplifiers. Its 2.5 V to 10 V operating range supports several low-voltage supply architectures, and the 5 mA per-channel output capability is adequate for ordinary high-impedance measurement stages. Engineers should account for the 60 dB gain-bandwidth product and confirm output settling before using high gain with rapidly changing signals.
Recomendado
Low-Power Voltage Buffer
The TS942BID can serve as a voltage buffer when the source has a relatively high output impedance and the downstream circuit requires reduced loading. Rail-to-rail output operation is useful near the available supply range, while approximately 1.2 µA supply current per channel helps preserve battery life. The dual package can buffer a reference and measurement channel, or two sensor outputs, within one footprint. Because the 60 dB gain-bandwidth product limits closed-loop bandwidth, use unity-gain buffering for high-frequency signals and verify capacitive-load stability in the intended layout.
Recomendado
Industrial Low-Level Amplification
The TS942BID can amplify low-level signals in industrial monitoring circuits where each channel must operate with low quiescent current. Its dual-channel configuration supports two amplifier paths in an 8-SOIC package, while the 2.5 V to 10 V supply range covers common low-voltage control and measurement rails. The 60 dB gain-bandwidth product is most appropriate for process variables and other low-frequency quantities rather than high-speed communications. Use careful grounding, keep input traces short, and confirm input bias current, offset, and common-mode limits from the manufacturer datasheet for each sensor impedance.
Recomendado
Medical Monitor Front End
The TS942BID can be considered for low-frequency medical monitoring front ends when two low-power analog channels are required. Its approximately 1.2 µA supply current per channel reduces the amplifier contribution to overall portable-system power, and rail-to-rail output capability improves utilization of a restricted supply voltage. The part is best suited to slowly varying signals because its 60 dB gain-bandwidth product limits bandwidth at higher closed-loop gains. Medical designs must separately verify safety, leakage, offset, noise, and application-specific requirements using the complete manufacturer datasheet and applicable design validation.
Recomendado
Audio and Environmental Monitoring
The TS942BID can buffer environmental or audio-monitoring inputs when the signal bandwidth is modest and power consumption is important. The dual channels can process left and right monitoring paths, or a sensor and its reference, within one 8-SOIC package. Rail-to-rail output behavior is useful in low-voltage systems, but its 60 dB gain-bandwidth product is not intended for high-fidelity wideband audio stages. Designers should keep the gain low for the widest bandwidth, evaluate input noise against the signal floor, and avoid placing sensitive input traces beside switching regulators or digital clocks.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TS942BID — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Package | 8-SOIC, 0.154 inch, 3.90 mm width |
| Brand | STMicroelectronics |
| Amplifier Type | Rail-to-rail output micropower operational amplifier |
| Number of Circuits | 2 circuits |
| Supply Voltage Range | 2.5 V to 10 V |
| Gain-Bandwidth Product | 60 dB |
| Output Current per Channel | 5 mA |
| Supply Current per Channel | 1.2 µA |
| Input Bias Current | 0.00015 µA |
| Operating Temperature Range | -40°C to +85°C |
Principais diferenciais
- Dual micropower channels in one package (vs Single-channel TS942-family implementations)
- Low-voltage rail-to-rail operation (vs Higher-supply general-purpose op amps)
- Low-power signal conditioning (vs Higher-bandwidth amplifiers)
Notas de projeto
Place each amplifier’s input, feedback, and bypass components close to their associated pins. The TS942BID uses a compact 8-SOIC footprint, so minimizing trace length around the feedback loop helps control parasitic capacitance and improve settling behavior. Keep high-impedance input nodes away from clocks, switching-regulator nodes, and other high-current traces.
Account for the 60 dB gain-bandwidth product when selecting feedback resistors and setting closed-loop gain. Bandwidth decreases in proportion to noise gain, so a nominal gain of 1 provides approximately 1 kHz of bandwidth. Verify the required signal bandwidth, phase margin, and settling behavior with the actual feedback network and source impedance.
Do not treat a similar TS942 order code as a confirmed substitute without checking its exact order-information entry. The TS942BID must retain the required 8-SOIC footprint, pin assignment, 2.5 V to 10 V operating range, and suitable output-current capability. Also verify capacitive-load stability and output swing before driving a load close to the supply rails.
Budget the TS942BID’s approximately 1.2 µA supply current per channel together with output-current demand and load power. The number 1.2 µA represents the quoted per-channel supply current, not total board consumption; regulators, pull networks, sensors, and downstream loads can dominate the final power budget. Confirm quiescent current across the intended supply voltage and temperature range.
Informações de conformidade
The component is a general-purpose analog IC, so AEC-Q100 is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product page or material declaration.