TUSB1310AZAY - 5 Gbps USB 3.0 Transceiver | Texas Instruments
N.º da peça: TUSB1310AZAY ✓ AtivoTUSB1310AZAY Visão geral
A USB 3.0 transceiver is an interface IC that connects a USB controller or host to a SuperSpeed data link. It forms part of the hierarchy USB interface device, transceiver, interface IC, and semiconductor. Unlike a passive connector, the transceiver converts parallel controller data into high-speed differential signaling and receives differential signal information for the controller. The TUSB1310A also supports PIPE and ULPI interfaces, allowing it to connect with controllers that use either interface style.
Principal features include one USB 3.0 port, a 5.0 Gbps maximum data rate, four selectable reference-clock frequencies, and integrated USB power-state handling. The USB 3.0 power states named in the manufacturer documentation are U0, U1, U2, and U3. The PIPE specification defines P0, P1, P2, and P3, while the POWER_DOWN pin is mapped to LTSSM states as described in the manufacturer datasheet.
The device operates from a single reference clock supplied by either a crystal or an external clock source. The manufacturer describes the 20, 25, 30, and 40 MHz selection as enabling a cost-effective USB 3.0 implementation with few external components. Because the transceiver can provide the reference clock to the USB controller, the design can reduce the number of independent clock sources required on the board.
Typical uses include USB 3.0 host-controller systems, USB device controllers, external data-transfer equipment, test and measurement products, and embedded computing platforms that require a SuperSpeed interface. The PIPE and ULPI choices are particularly useful when a system already has a controller designed around one of those interfaces. The 175-NFBGA package also supports compact layouts where the electrical and thermal design can be controlled carefully.
When implementing the TUSB1310AZAY, follow the manufacturer datasheet for high-speed differential routing, reference-clock configuration, supply decoupling, ball assignment, and test-point access. Its 12 x 12 mm BGA footprint requires careful escape routing and multilayer PCB planning. Confirm that the selected controller supports the intended PIPE or ULPI mode and verify the complete USB link-training sequence during hardware validation.
This page consolidates the exact ordering information, interface capabilities, clock choices, package details, replacement information, and engineering design considerations for engineers evaluating a USB 3.0 SuperSpeed physical-layer implementation.
Alternativas drop-in para TUSB1310AZAY — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com TUSB1310AZAY (mesmo formato e footprint) — diferindo em Clock Source, Product Type.
TUSB1310ZAY
✅ Drop-InConsulte o preço
Ver ficha técnica →TUSB1310AZAY Especificações
| Product Type | Single-port SuperSpeed USB 3.0 physical-layer transceiver |
| USB Generation | USB 3.0 |
| Maximum Data Rate | 5.0 Gbps |
| Port Count | 1 port |
| Controller Interface Options | PIPE and ULPI |
| Reference Clock Frequencies | 20, 25, 30, and 40 MHz |
| Clock Source | Crystal or external reference clock |
| Reference Clock Output | Provided to the USB controller |
| USB Power States | U0, U1, U2, and U3 |
| PIPE Power States | P0, P1, P2, and P3 |
| POWER_DOWN Function | Mapped to LTSSM states |
| Faixa de temperatura de operação | -40 °C to +85 °C |
| Encapsulamento | 175-NFBGA, 12 x 12 mm |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do TUSB1310AZAY 175-nfbga, 12 x 12 mm
Configuração de pinos para TUSB1310AZAY (pacote 175-nfbga, 12 x 12 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para TUSB1310AZAY.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
TUSB1310AZAY é adequado para 6 aplicaçãos: USB 3.0 Host Controller Systems, External Data Transfer Equipment, Industrial USB Data Acquisition, USB Test and Measurement Equipment, Embedded Computing Platforms, Network Adapter and Bridge Products.
USB 3.0 Host Controller Systems
The TUSB1310AZAY fits a USB 3.0 host-controller design requiring a 5.0 Gbps SuperSpeed physical layer with PIPE or ULPI connectivity. It uses one 20, 25, 30, or 40 MHz reference clock and can provide that clock to the controller, reducing the need for separate clock sources. In this topology, the transceiver sits between the host controller and the external SuperSpeed connection, while the USB controller manages protocol traffic and LTSSM operation. The design advantage is a compact 175-NFBGA, 12 x 12 mm implementation with a manufacturer-described low external-component count. Board designers should still reserve short differential routes, clean reference-clock connections, and suitable power decoupling according to the manufacturer layout guidance.
Recomendado
External Data Transfer Equipment
The TUSB1310AZAY is appropriate for external storage, docking, and data-transfer products that need a 5.0 Gbps USB 3.0 connection. The single-port transceiver accepts either PIPE or ULPI signaling from the controller, allowing firmware and board architecture to remain compatible with more than one controller interface. A shared reference clock at 20, 25, 30, or 40 MHz simplifies the physical implementation and can lower the number of oscillators required around the controller. For a compact enclosure, the 12 x 12 mm 175-NFBGA package is useful, but its dense ball pattern requires multilayer routing and careful assembly-process control. Signal-integrity validation should include compliance margin, hot-plug behavior, and link-training performance.
Recomendado
Industrial USB Data Acquisition
The TUSB1310AZAY can serve as the SuperSpeed interface in industrial data-acquisition equipment that transfers measurement data to a host at rates up to 5.0 Gbps. Its selectable reference-clock frequencies of 20, 25, 30, or 40 MHz allow the physical layer to align with the selected controller and clock architecture. The PIPE interface supports controller arrangements built around that protocol, while ULPI provides an alternative for compatible USB controllers. Using one reference clock for the transceiver and controller may reduce board area and clock-distribution complexity. In an industrial environment, enclosure temperature, power-supply integrity, and connector launch geometry remain important system-level constraints. Prototype testing should confirm recovery behavior, clock jitter tolerance, and sustained-transfer stability.
Recomendado
USB Test and Measurement Equipment
The TUSB1310AZAY is suitable for USB-based test and measurement instruments that need a fast, deterministic host connection for transferring waveforms, configuration data, or captured samples. The 5.0 Gbps SuperSpeed capability reduces transfer time compared with lower-speed USB links, while PIPE and ULPI support gives designers two controller-interface options. The selectable 20, 25, 30, or 40 MHz reference clock can be shared with the controller to simplify synchronization. For instruments with sensitive internal analog sections, the physical-layer device should be kept away from sensitive routes, and clock and supply references must follow the manufacturer layout guidance. Bring-up should exercise repeated enumeration, suspend and resume, error recovery, and sustained transfers to verify link stability.
Recomendado
Embedded Computing Platforms
The TUSB1310AZAY supports embedded computing platforms that expose a SuperSpeed USB port to an external display, storage device, dock, or network adapter. A 5.0 Gbps physical layer provides the link bandwidth expected from USB 3.0 while offering both PIPE and ULPI controller choices. Because the transceiver can operate from one crystal or external clock and supply the controller reference, a platform designer can consolidate clock resources and reduce board complexity. The 175-NFBGA package helps achieve a compact result, although multilayer escape routing and assembly inspection must be planned from the outset. Firmware should validate link-speed negotiation and fall back to lower USB speeds when cable or connector conditions prevent reliable SuperSpeed operation.
Recomendado
Network Adapter and Bridge Products
The TUSB1310AZAY can be used in a USB-to-network adapter or protocol-bridge product where an external USB 3.0 host connects to an embedded processing subsystem. The physical-layer transceiver operates at up to 5.0 Gbps and communicates with the local controller through PIPE or ULPI, while the controller manages USB protocol behavior and the bridge function. Its selectable clock options of 20, 25, 30, or 40 MHz support flexible platform clock plans, and the shared reference-clock capability can reduce oscillator count. The dense 175-NFBGA package requires a multilayer PCB with careful length matching and reference-plane continuity. Production validation should include enumeration across host operating systems, thermal testing at sustained data rates, and recovery tests after cable disturbance.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TUSB1310AZAY — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TUSB1310ZAY |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 175-NFBGA (12x12) | 175-NFBGA (12x12), pin-compatible |
| Product Type | Single-port USB 3.0 physical-layer transceiver | Single-port USB 3.0 physical-layer transceiver |
| Maximum Data Rate | 5.0 Gbps | 5.0 Gbps |
| Controller Interfaces | PIPE and ULPI | PIPE and ULPI |
| Reference Clock Frequencies | 20, 25, 30, and 40 MHz | 20, 25, 30, and 40 MHz |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C |
| Electrical and Timing Difference | Reference configuration | No significant difference reported |
Principais diferenciais
- Documented pin-compatible replacement path (vs TUSB1310ZAY)
- Flexible controller-interface selection (vs TUSB1310ZAY)
- Shared reference-clock architecture (vs TUSB1310ZAY)
Notas de projeto
Plan the 175-NFBGA layout as a multilayer high-speed design rather than treating it as a conventional perimeter package. Escape the SuperSpeed differential pairs directly from the transceiver to the connector or next stage with the shortest practical path, preserve continuous reference planes, and follow the manufacturer's recommended ball pattern and layer stack. Confirm assembly capability for the dense 12 x 12 mm land pattern before releasing the board.
Validate the reference clock and high-speed links with the actual controller, PCB, connector, and cable configuration. The transceiver supports 20, 25, 30, and 40 MHz reference-clock frequencies, so configuration errors can affect the entire USB link. Check differential impedance, return loss, insertion loss, clock jitter, and margin across SuperSpeed operation, then repeat tests during repeated enumeration and suspend-resume cycles.
Follow the manufacturer power-supply and decoupling recommendations before calculating additional board-level power headroom. The USB power states U0, U1, U2, and U3 and the mapped POWER_DOWN behavior make low-power transitions part of normal operation. Place recommended capacitors close to their designated supply balls, keep supply and return paths short, and verify startup and shutdown behavior with the selected reference-clock configuration.
Do not substitute a USB controller interface without confirming the PIPE or ULPI mode supported by the TUSB1310AZAY and the chosen controller. Also avoid treating a different USB transceiver as a drop-in part merely because it supports USB 3.0: footprint, ball functions, voltage requirements, clocking, and controller handshaking must all match. Use the complete manufacturer ball map and interface timing documentation during schematic and PCB review.
Informações de conformidade
The manufacturer product page and datasheet links were identified, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was established for this exact ordering suffix. Check the current manufacturer product and quality documentation before making a compliance claim.