Z86E0408SEC 8-Bit 8MHz 1KB OTP MCU | Zilog
N.º da peça: Z86E0408SEC ✗ Fim de vidaZ86E0408SEC Visão geral
An 8-bit microcontroller is a compact processing platform intended for control-oriented products that monitor inputs, operate actuators, and manage system functions through embedded software. Within the semiconductor hierarchy, the Z86E0408SEC belongs to the Z8 microcontroller family, an embedded processor and system-controller category designed for dedicated appliances, industrial controls, and simple electronic equipment.
The principal device characteristics are an 8-bit CPU, an 8 MHz maximum clock, and 1 KB of OTP program memory. The 18SOIC package supports conventional surface-mount PCB assembly. OTP memory provides a secure one-time programming method for fixed firmware, which can simplify product configuration and prevent routine field reprogramming. Other electrical, timing, peripheral, environmental, and package dimensions require confirmation from the manufacturer datasheet before design release.
Z8 devices are commonly evaluated for small control loops rather than high-throughput embedded processing. At an 8 MHz operating rate, the processor is suited to sequential logic, button and switch handling, status indicators, and supervisory functions. Firmware size and execution timing should be checked against the 1 KB OTP limit, while final timing margin must include peripheral setup and interrupt-handling overhead.
Typical design uses include compact appliance controls, industrial interface modules, instrumentation peripherals, and small embedded controllers that require deterministic one-time-programmed firmware. The 18SOIC footprint is practical for through-board assembly and designs that favor a conventional small-outline package over a larger fine-pitch controller package.
Design planning should begin with the pin description table, electrical limits, clock requirements, and programming procedure in the manufacturer datasheet. Confirm the operating-voltage range, available I/O count, oscillator configuration, reset requirements, and programming connector details before final schematic capture. PCB layouts should reserve space and isolation for the programming interface because OTP devices cannot be updated after programming.
This product page consolidates the verified device identity, architecture, memory configuration, clock rate, package format, lifecycle information, sourcing workflow, and practical design guidance. It also distinguishes the documented Z86E0408SEC from unverified substitutes and explains why footprint-compatible alternatives require separate pin, function, memory, timing, and programming verification.
Alternativas drop-in para Z86E0408SEC — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasZ86E0408SEC Classificações máximas e características elétricas
| Product Type | 8-bit embedded microcontroller |
| Processor Architecture | Z8 architecture |
| CPU Word Size | 8 bit |
| Frequência máxima de clock | 8 MHz |
| Program Memory Type | 1 KB OTP |
| Program Memory Organization | 1K x 8 bit |
| Package Type | 18-pin SOIC |
| Package Designation | 18SOIC |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do Z86E0408SEC 18soic
Configuração de pinos para Z86E0408SEC (pacote 18soic). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para Z86E0408SEC.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
Z86E0408SEC é adequado para 6 aplicaçãos: Compact Appliance Control, Industrial Interface Module, Instrumentation Peripheral Controller, LED and Indicator Sequencer, Security and Access Controller, Legacy Control-System Spare.
Compact Appliance Control
The Z86E0408SEC fits compact appliance-control tasks that use an 8-bit processor, sequential logic, and limited fixed firmware. Its 8 MHz operating rate is suitable for routine input scanning, operating-state decisions, indicator control, and actuator sequencing, while 1 KB of OTP program memory supports a one-time-programmed firmware image. The 18SOIC package also provides a conventional surface-mount option for compact boards. Before committing to a design, confirm the complete pinout, operating voltage, available I/O, oscillator arrangement, reset behavior, and watchdog requirements. The OTP architecture is particularly appropriate when field updates are unnecessary and a fixed control program improves configuration control.
Industrial Interface Module
The Z86E0408SEC can serve as the controller in a small industrial interface module when the module primarily translates discrete inputs into controlled outputs and does not require large data storage or high-bandwidth computation. The 8-bit Z8 architecture and 8 MHz clock support deterministic supervisory loops, status reporting, and basic protection logic. Its 18SOIC footprint simplifies assembly into a module that already routes power, clock, programming, and field-connection signals. Engineering review must establish the electrical limits of every I/O, the supported supply range, isolation requirements, and behavior during reset. The 1 KB OTP capacity should be checked against the final code, configuration constants, and diagnostic routines before programming begins.
Instrumentation Peripheral Controller
The Z86E0408SEC is suitable for a small instrumentation peripheral that manages switches, indicators, calibration-related flags, and a constrained control sequence. At up to 8 MHz, the 8-bit processor can execute deterministic menu logic, sensor-selection routines, and supervisory functions without requiring a larger application processor. The 1 KB OTP program store favors permanent firmware in a dedicated peripheral, while the 18SOIC package supports compact board layouts. Designers should verify whether the required sensor interface, display control, communication baud rate, and timing margins fall within the device's documented peripherals and clock configuration. A prototype should also validate startup behavior, reset timing, and programming access before the memory is permanently programmed.
LED and Indicator Sequencer
The Z86E0408SEC can control LED banks, status indicators, or small display sequences when the required behavior is deterministic and the complete firmware fits in 1 KB of OTP memory. Its 8 MHz clock provides sufficient sequential processing capability for periodic updates, blink patterns, fault indication, and button-driven mode changes. Using the 18SOIC package makes the controller easy to place beside an LED driver or logic interface. The design should not assume that every package pin is a general-purpose output; use the manufacturer pin-description table to identify valid I/O, shared functions, and any port constraints. Confirm output-drive capability, supply voltage, and timing behavior for the attached LEDs, including whether constant-current driver circuitry is required.
Security and Access Controller
The Z86E0408SEC can support a simple access-control peripheral that reads switches, evaluates authorization states, and activates an electric lock or indicator. OTP program memory is useful when the controller must hold fixed authorization logic that should not be rewritten during normal service. The 8-bit processor and 8 MHz clock are appropriate for low-complexity sequencing and status management, and the 18SOIC package supports compact PCB assembly. A security-focused design still requires a clear threat model and must prevent unauthorized programming or physical bypass. Confirm fail-safe behavior, reset-state pin levels, relay-drive circuitry, operating voltage, and programming-access controls using the manufacturer documentation before deployment.
Legacy Control-System Spare
The Z86E0408SEC is appropriate for maintaining a legacy control system that already uses its exact Z8 architecture, 18SOIC footprint, and 1 KB OTP configuration. This use is most practical for repair or production continuity where redesign would create unnecessary qualification and firmware risk. The documented 8 MHz clock and compact processor support the original control functions, but the device's discontinued status requires careful supply planning. Confirm the required pin functions, electrical characteristics, OTP programming method, and every hardware connection before substitution. For long-term support, compare the cost of maintaining legacy production against qualifying a currently supported MCU with a controlled board and firmware revision.
Dados de referência de engenharia para Z86E0408SEC — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Brand | Zilog |
| Package | 18SOIC |
| CPU Architecture | Z8 8-bit |
| Maximum Clock Frequency | 8 MHz |
| Program Memory | 1 KB OTP |
| Program Memory Organization | 1K x 8 bit |
| Product Category | Embedded microcontroller |
| Lifecycle Status | Discontinued |
| Mounting Type | Surface mount |
Principais diferenciais
- Compact 8-bit Z8 control platform (vs No verified drop-in alternative)
- One-time-programmable firmware storage (vs Generic 8-bit 18SOIC MCU)
- Established legacy footprint (vs No verified drop-in alternative)
Notas de projeto
Do not treat every 18SOIC 8-bit MCU as a pin-compatible replacement for the Z86E0408SEC. Before substitution, compare the complete manufacturer pin tables for supply, ground, oscillator, reset, programming, and I/O assignments. Also verify operating voltage, I/O drive limits, timer resources, interrupt mapping, clock tolerances, and programming voltages. A successful footprint comparison alone does not establish that the existing firmware or PCB will operate correctly.
Reserve a dedicated programming connection and adequate board-edge or via access for the OTP programming fixture. Because program memory is one-time programmable, protect the programming interface from accidental access after manufacturing and provide a documented irreversible programming step. Follow the manufacturer layout requirements for the 18SOIC footprint, including pad geometry, solder-mask definition, and thermal or copper recommendations where applicable.
Validate the power architecture against the manufacturer operating-voltage range, I/O current limits, startup behavior, and external load demands before assigning supply pins. Estimated: if the final design consumes 10 mA at a 5 V rail, the regulator must support that load plus startup margin; because the allowable voltage and current are not established here, calculate thermal and electrical limits from the datasheet before component selection.
Fit the final firmware within the 1 KB OTP program-memory limit before committing the device. Include initialization, fault handling, constants, and required diagnostic functions in the build map rather than measuring only executable code size. Confirm interrupt latency, oscillator startup, and peripheral timing against the 8 MHz operating rate. OTP devices are not field-updateable, so a programming mistake generally requires replacing the device.
Informações de conformidade
The product listing confirms the device identity and lifecycle status but does not establish the requested compliance attributes.