УВЕДОМЛЕНИЕ О ПОСЛЕДНЕЙ ЗАКУПКЕ: Z86E0408SEC приближается к снятию с производства. Последняя дата заказа: Свяжитесь с нами. Смотреть доступные аналоги →
Zilog

Z86E0408SEC 8-Bit 8MHz 1KB OTP MCU | Zilog

Артикул: Z86E0408SEC ✗ Снят с производства
18-pin SOIC Package 8 MHz Speed 1 KB OTP Memory
MOQ: 1 |

Z86E0408SEC Обзор

Zilog Z86E0408SEC is an 8-bit embedded microcontroller operating at up to 8 MHz, with 1 KB of one-time-programmable program memory and an 18-pin SOIC package. The Z8 architecture combines a compact general-purpose MCU format with OTP program storage for cost-sensitive embedded control designs.

An 8-bit microcontroller is a compact processing platform intended for control-oriented products that monitor inputs, operate actuators, and manage system functions through embedded software. Within the semiconductor hierarchy, the Z86E0408SEC belongs to the Z8 microcontroller family, an embedded processor and system-controller category designed for dedicated appliances, industrial controls, and simple electronic equipment.

The principal device characteristics are an 8-bit CPU, an 8 MHz maximum clock, and 1 KB of OTP program memory. The 18SOIC package supports conventional surface-mount PCB assembly. OTP memory provides a secure one-time programming method for fixed firmware, which can simplify product configuration and prevent routine field reprogramming. Other electrical, timing, peripheral, environmental, and package dimensions require confirmation from the manufacturer datasheet before design release.

Z8 devices are commonly evaluated for small control loops rather than high-throughput embedded processing. At an 8 MHz operating rate, the processor is suited to sequential logic, button and switch handling, status indicators, and supervisory functions. Firmware size and execution timing should be checked against the 1 KB OTP limit, while final timing margin must include peripheral setup and interrupt-handling overhead.

Typical design uses include compact appliance controls, industrial interface modules, instrumentation peripherals, and small embedded controllers that require deterministic one-time-programmed firmware. The 18SOIC footprint is practical for through-board assembly and designs that favor a conventional small-outline package over a larger fine-pitch controller package.

Design planning should begin with the pin description table, electrical limits, clock requirements, and programming procedure in the manufacturer datasheet. Confirm the operating-voltage range, available I/O count, oscillator configuration, reset requirements, and programming connector details before final schematic capture. PCB layouts should reserve space and isolation for the programming interface because OTP devices cannot be updated after programming.

This product page consolidates the verified device identity, architecture, memory configuration, clock rate, package format, lifecycle information, sourcing workflow, and practical design guidance. It also distinguishes the documented Z86E0408SEC from unverified substitutes and explains why footprint-compatible alternatives require separate pin, function, memory, timing, and programming verification.

Аналоги без доработки для Z86E0408SEC — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Для этого товара нет аналогов без доработки.

Запросить аналоги

Z86E0408SEC Максимальные параметры и электрические характеристики

Product Type 8-bit embedded microcontroller
Processor Architecture Z8 architecture
CPU Word Size 8 bit
Максимальная тактовая частота 8 MHz
Program Memory Type 1 KB OTP
Program Memory Organization 1K x 8 bit
Package Type 18-pin SOIC
Package Designation 18SOIC
Тип монтажа Surface mount

Руководство по цоколевке Z86E0408SEC в корпусе 18soic

Цоколевка для Z86E0408SEC (корпус 18soic). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.

Схема цоколевки корпуса 18soic для Z86E0408SEC

Нет подробных данных о распиновке для Z86E0408SEC.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

Z86E0408SEC подходит для 6 применениеs: Compact Appliance Control, Industrial Interface Module, Instrumentation Peripheral Controller, LED and Indicator Sequencer, Security and Access Controller, Legacy Control-System Spare.

🔧

Compact Appliance Control

The Z86E0408SEC fits compact appliance-control tasks that use an 8-bit processor, sequential logic, and limited fixed firmware. Its 8 MHz operating rate is suitable for routine input scanning, operating-state decisions, indicator control, and actuator sequencing, while 1 KB of OTP program memory supports a one-time-programmed firmware image. The 18SOIC package also provides a conventional surface-mount option for compact boards. Before committing to a design, confirm the complete pinout, operating voltage, available I/O, oscillator arrangement, reset behavior, and watchdog requirements. The OTP architecture is particularly appropriate when field updates are unnecessary and a fixed control program improves configuration control.

🏭

Industrial Interface Module

The Z86E0408SEC can serve as the controller in a small industrial interface module when the module primarily translates discrete inputs into controlled outputs and does not require large data storage or high-bandwidth computation. The 8-bit Z8 architecture and 8 MHz clock support deterministic supervisory loops, status reporting, and basic protection logic. Its 18SOIC footprint simplifies assembly into a module that already routes power, clock, programming, and field-connection signals. Engineering review must establish the electrical limits of every I/O, the supported supply range, isolation requirements, and behavior during reset. The 1 KB OTP capacity should be checked against the final code, configuration constants, and diagnostic routines before programming begins.

📺

Instrumentation Peripheral Controller

The Z86E0408SEC is suitable for a small instrumentation peripheral that manages switches, indicators, calibration-related flags, and a constrained control sequence. At up to 8 MHz, the 8-bit processor can execute deterministic menu logic, sensor-selection routines, and supervisory functions without requiring a larger application processor. The 1 KB OTP program store favors permanent firmware in a dedicated peripheral, while the 18SOIC package supports compact board layouts. Designers should verify whether the required sensor interface, display control, communication baud rate, and timing margins fall within the device's documented peripherals and clock configuration. A prototype should also validate startup behavior, reset timing, and programming access before the memory is permanently programmed.

💡

LED and Indicator Sequencer

The Z86E0408SEC can control LED banks, status indicators, or small display sequences when the required behavior is deterministic and the complete firmware fits in 1 KB of OTP memory. Its 8 MHz clock provides sufficient sequential processing capability for periodic updates, blink patterns, fault indication, and button-driven mode changes. Using the 18SOIC package makes the controller easy to place beside an LED driver or logic interface. The design should not assume that every package pin is a general-purpose output; use the manufacturer pin-description table to identify valid I/O, shared functions, and any port constraints. Confirm output-drive capability, supply voltage, and timing behavior for the attached LEDs, including whether constant-current driver circuitry is required.

🧩

Security and Access Controller

The Z86E0408SEC can support a simple access-control peripheral that reads switches, evaluates authorization states, and activates an electric lock or indicator. OTP program memory is useful when the controller must hold fixed authorization logic that should not be rewritten during normal service. The 8-bit processor and 8 MHz clock are appropriate for low-complexity sequencing and status management, and the 18SOIC package supports compact PCB assembly. A security-focused design still requires a clear threat model and must prevent unauthorized programming or physical bypass. Confirm fail-safe behavior, reset-state pin levels, relay-drive circuitry, operating voltage, and programming-access controls using the manufacturer documentation before deployment.

🖥️

Legacy Control-System Spare

The Z86E0408SEC is appropriate for maintaining a legacy control system that already uses its exact Z8 architecture, 18SOIC footprint, and 1 KB OTP configuration. This use is most practical for repair or production continuity where redesign would create unnecessary qualification and firmware risk. The documented 8 MHz clock and compact processor support the original control functions, but the device's discontinued status requires careful supply planning. Confirm the required pin functions, electrical characteristics, OTP programming method, and every hardware connection before substitution. For long-term support, compare the cost of maintaining legacy production against qualifying a currently supported MCU with a controlled board and firmware revision.

What is the Z86E0408SEC?
The Z86E0408SEC is a Zilog Z8-series 8-bit embedded microcontroller rated for operation at up to 8 MHz, with 1 KB of one-time-programmable program memory in an 18-pin SOIC package. Its compact architecture is intended for dedicated control functions rather than general-purpose computing. The manufacturer datasheet should be used to confirm pin functions, electrical limits, clocking options, and programming requirements before the device is placed in a production design.
What are the key specifications of Z86E0408SEC that engineers should know?
The key documented specifications are an 8-bit CPU, an operating frequency of up to 8 MHz, 1 KB of OTP program memory organized as 1K x 8 bit, and an 18SOIC package. The device is categorized as an embedded microcontroller and its lifecycle status is discontinued. Input voltage, I/O count, data-memory capacity, reset behavior, and electrical timing must be confirmed from the manufacturer datasheet before schematic or firmware release.
How much program memory does the Z86E0408SEC have?
The Z86E0408SEC contains 1 KB of one-time-programmable program memory, described as 1K x 8 bit. Because the memory is OTP, the final firmware is fixed after programming and cannot ordinarily be rewritten in the field. Engineers should include boot checks, fault handling, and configuration values in the program-memory budget and verify the programming procedure against the manufacturer datasheet before committing a production design.
What is the operating frequency of Z86E0408SEC?
The Z86E0408SEC operates at up to 8 MHz according to the Z8 Microcontroller product listing. This clock rate supports compact sequential control tasks, including input scanning, status logic, and actuator sequencing. Actual timing margin depends on the selected clock source, firmware path, interrupt workload, and peripheral configuration, all of which should be evaluated against the manufacturer timing and electrical specifications.
Where can I download the Z86E0408SEC datasheet PDF?
The Z86E0408SEC datasheet is available through the Zilog document listing at https://www.datasheets.com/ixys/z86e0408sec. Use the manufacturer pin-description table, electrical-characteristics tables, and programming instructions to establish the authoritative design values. The search index identifies the device as an 8-bit Z8 microcontroller with 8 MHz operation, 1 KB OTP memory, and an 18SOIC package.
Where can I find the Z86E0408SEC pinout?
The Z86E0408SEC pinout must be taken from the pin-description table in the manufacturer datasheet, available through the document page at https://www.datasheets.com/ixys/z86e0408sec. The package is identified as 18SOIC, but individual signal names, power pins, reset behavior, oscillator connections, and programming pins are not reproduced here without a verified pin table. Use those documented assignments when assigning PCB tracks.
Is Z86E0408SEC still active?
No. The Z86E0408SEC is identified as discontinued, so its lifecycle status is recorded as end of life. Engineers designing a new product should check whether a supported Zilog family member provides the required memory, clock, peripherals, package, and programming workflow. If an existing design must retain this part, request lifecycle, stock, and sourcing confirmation through the Request a Quote form on this page.
Where can I buy Z86E0408SEC online?
Use the Request a Quote form on this page to request Z86E0408SEC availability, minimum order quantity, current lead time, and fulfillment options. Because the device is discontinued, stock and lifecycle conditions may change more quickly than for an active component. The request should include the exact MPN, Z86E0408SEC, and any required quantity so the sourcing response can be matched to the correct 18SOIC configuration.
What is the price of Z86E0408SEC?
The current Z86E0408SEC price is shown through the Request a Quote form on this page rather than as a static price statement. Pricing can vary with quantity, stock position, package configuration, inspection requirements, and supply continuity for a discontinued microcontroller. Submit the required quantity and any production schedule with the quote request so current commercial terms can be evaluated accurately.
What is the lead time for Z86E0408SEC?
Request the current Z86E0408SEC lead time through the Request a Quote form on this page. As a discontinued 8-bit MCU with 1 KB OTP memory in an 18SOIC package, its supply interval depends on remaining inventory and lot traceability. Include your required quantity, target delivery date, and acceptable date-code policy in the request to obtain a practical sourcing response.
Is Z86E0408SEC in stock?
Stock status for the discontinued Z86E0408SEC should be confirmed through the Request a Quote form on this page. Search listings may show historical or changing inventory quantities, so they should not be treated as a guaranteed allocation. The exact MPN and required quantity are essential because 18SOIC packaging, lot traceability, and production-stage requirements can affect what can be supplied.
What is the difference between Z86E0408SEC and another 8-bit MCU in an 18SOIC package?
The Z86E0408SEC is specifically an 8 MHz Z8 8-bit MCU with 1 KB of OTP program memory in an 18SOIC package. Another microcontroller in the same package may differ in memory technology, RAM, peripherals, oscillator arrangement, reset logic, programming connector, voltage range, or pin assignment. A valid comparison therefore requires both a package check and a functional pin-by-pin check rather than package size alone.
When should I choose Z86E0408SEC over another 8-bit microcontroller?
Choose the Z86E0408SEC only when an existing design benefits from the exact Z86E0408SEC footprint, 8-bit architecture, 8 MHz clock, and 1 KB OTP program memory and when its discontinued status is acceptable. For a new design, prefer a currently supported MCU with adequate RAM, peripherals, voltage range, and development-tool support. Legacy repair or production-continuity use should be weighed against long-term availability and programming compatibility.
Is Z86E0408SEC suitable for a compact appliance controller?
The Z86E0408SEC can suit a compact appliance controller when the required control logic fits within 1 KB of OTP program memory and the board uses the documented 18SOIC pinout. Its 8 MHz Z8 core is appropriate for sequential input, output, and supervisory tasks. Before selection, verify operating voltage, I/O availability, oscillator support, watchdog behavior, reset requirements, and any safety or appliance-specific compliance needs.
What is the best drop-in replacement for Z86E0408SEC?
No verified drop-in replacement for the Z86E0408SEC is established by the available cross-reference results. A true replacement must use the same 18SOIC footprint, preserve pin functions and power connections, support 8 MHz operation, provide at least 1 KB of OTP-compatible program memory, and match the electrical and programming requirements. Substitute candidates should not be approved from a package name or headline clock-rate comparison alone.
Can a cross-brand 18SOIC MCU replace Z86E0408SEC?
A cross-brand 18SOIC MCU may replace the Z86E0408SEC only after a complete engineering equivalence review. The candidate must match the physical land pattern, pin-by-pin signal functions, supply voltage, clock pins, reset behavior, I/O electrical limits, OTP programming method, and application firmware assumptions. No cross-brand drop-in candidate is documented here, so any proposed equivalent requires schematic, firmware, and hardware validation before substitution.
What can replace Z86E0408SEC?
The Z86E0408SEC has no verified direct replacement in the documented cross-reference results. The safest replacement path is to identify an MCU with the same 18SOIC footprint and confirm every power, clock, reset, programming, and I/O connection against the manufacturer pin table. If no candidate passes that review, retain the existing footprint and qualify a supported controller with a deliberate schematic and firmware revision rather than treating it as a pin-compatible substitution.
Is Z86E0408SEC the same as a generic 8-bit 18SOIC MCU?
No. The Z86E0408SEC has a specific Z8 architecture, 8 MHz maximum clock, 1 KB OTP program memory, and defined pin assignments in an 18SOIC package. A generic 8-bit MCU with the same package may use different power pins, oscillator pins, programming signals, interrupt sources, or peripheral functions. Treat it as a functional replacement only after comparing the manufacturer pin tables and validating the associated firmware.

Справочные инженерные данные для Z86E0408SEC — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the Z86E0408SEC for an existing design that specifically requires its Z8 architecture, 1 KB OTP program memory, 8 MHz maximum clock, and 18SOIC footprint. It is most appropriate for repair or controlled legacy production where a board and firmware redesign would add risk. For a new design, first evaluate a currently supported 8-bit MCU with sufficient RAM, peripherals, development tools, and supply assurance. Do not substitute a generic 18SOIC part merely because the package dimensions match: verify pin assignments, supply voltage, clocking, reset, programming signals, I/O limits, interrupt mapping, and memory organization. No verified drop-in alternative is established for this MPN, so a redesign should be treated as a controlled engineering change rather than a stock substitution. For current price, stock, and lead-time confirmation, use the Request a Quote form on this page.

Сравнение с аналогами

Параметр Этот товар
Brand Zilog
Package 18SOIC
CPU Architecture Z8 8-bit
Maximum Clock Frequency 8 MHz
Program Memory 1 KB OTP
Program Memory Organization 1K x 8 bit
Product Category Embedded microcontroller
Lifecycle Status Discontinued
Mounting Type Surface mount

Ключевые отличия

  • Compact 8-bit Z8 control platform (против No verified drop-in alternative)
  • One-time-programmable firmware storage (против Generic 8-bit 18SOIC MCU)
  • Established legacy footprint (против No verified drop-in alternative)

Заметки по проектированию

Do not treat every 18SOIC 8-bit MCU as a pin-compatible replacement for the Z86E0408SEC. Before substitution, compare the complete manufacturer pin tables for supply, ground, oscillator, reset, programming, and I/O assignments. Also verify operating voltage, I/O drive limits, timer resources, interrupt mapping, clock tolerances, and programming voltages. A successful footprint comparison alone does not establish that the existing firmware or PCB will operate correctly.

Reserve a dedicated programming connection and adequate board-edge or via access for the OTP programming fixture. Because program memory is one-time programmable, protect the programming interface from accidental access after manufacturing and provide a documented irreversible programming step. Follow the manufacturer layout requirements for the 18SOIC footprint, including pad geometry, solder-mask definition, and thermal or copper recommendations where applicable.

Validate the power architecture against the manufacturer operating-voltage range, I/O current limits, startup behavior, and external load demands before assigning supply pins. Estimated: if the final design consumes 10 mA at a 5 V rail, the regulator must support that load plus startup margin; because the allowable voltage and current are not established here, calculate thermal and electrical limits from the datasheet before component selection.

Fit the final firmware within the 1 KB OTP program-memory limit before committing the device. Include initialization, fault handling, constants, and required diagnostic functions in the build map rather than measuring only executable code size. Confirm interrupt latency, oscillator startup, and peripheral timing against the 8 MHz operating rate. OTP devices are not field-updateable, so a programming mistake generally requires replacing the device.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The product listing confirms the device identity and lifecycle status but does not establish the requested compliance attributes.

Данные проверены: 2026-11-11 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

Z86E0408SEC datasheet Z86E0408SEC datasheet pdf Z86E0408SEC pinout Z86E0408SEC equivalent Z86E0408SEC replacement Z86E0408SEC cross reference Z86E0408SEC price Z86E0408SEC stock Zilog Z86E0408SEC Z86E0408SEC 8MHz Z86E0408SEC 1KB OTP Z86E0408SEC 18SOIC Z86E0408SEC application circuit Z86E0408SEC footprint

Связанные компоненты & термины

Zilog Z86E0408SEC Z8 microcontroller 8-bit microcontroller embedded microcontroller embedded processor microcontroller IC semiconductor OTP program memory one-time-programmable memory 8 MHz clock 18SOIC package surface-mount package industrial control appliance control instrumentation peripheral LED indicator control access control legacy system maintenance
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ