Интегральные схемы

PIC18F252-E/SP

PIC18F252-E/SP - 8-Bit MCU, 32KB Flash, 40MHz, SPDIP-28 | Microchip

The Microchip Technology PIC18F252-E/SP is an 8-bit CMOS flash microcontroller from the PIC18F family, delivered in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It integrates 32KB of program flash memory organized as 16K x 16 words, 1.5KB (1536 bytes) of SRAM, 256 bytes of EEPROM data memory, and a 40 MHz (10 MIPS) enhanced Harvard RISC core. The integrated peripherals include 23 digital I/O lines, a 10-bit multi-channel Analog-to-Digital Converter (ADC), two Capture/Compare/PWM (CCP) modules, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), a Master Synchronous Serial Port (MSSP) configurable as SPI or I2C, and an in-circuit debugger. What is a PIC18F microcontroller? PIC18F is Microchip Technology's family of high-performance 8-bit Reduced Instruction Set Computer (RISC) microcontrollers built on a Harvard memory architecture. They sit within the broader 8-bit MCU taxonomy (MCU -> microcontroller -> 8-bit MCU -> RISC MCU -> Harvard architecture MCU -> embedded controller) and target applications needing moderate computational throughput, low power, abundant peripherals, and broad developer tool support including MPLAB X IDE, XC8 compilers, and PICkit debuggers. Key technical features of the PIC18F252-E/SP include the self-programmable flash permitting in-field firmware updates, C compiler-optimized instruction set with 77 single-word instructions, an extended instruction set variant, and wide 4.2V to 5.5V supply tolerance. The -E temperature grade spans -40C to +125C, qualifying the device for industrial and harsh-environment use. The 28-pin SPDIP-28 (SP) form factor suits breadboarding, legacy designs, through-hole manufacturing, and hand-soldered prototypes where SMD reflow is impractical. Architecturally, PIC18F252-E/SP combines an 8-bit data path with a 16-bit instruction word, two address spaces for program and data memories, hardware multiplier for single-cycle 8x8 operations, and a vectored interrupt controller with prioritized sources. Two CCP modules can be configured for PWM, capture, or compare, enabling motor control, timing measurement, and waveform generation. The MSSP supports both SPI (4-wire with separate I/O) and I2C (master/slave, 7/10-bit addressing), giving designers a flexible peripheral mix. Typical applications include industrial control systems, HVAC thermostats, sensor signal conditioning, low-end motor drivers, instrumentation, and consumer appliances. The PIC18F252-E is well suited for designs migrating from PIC16F parts that need more code space, additional I/O, or higher ADC resolution. A key design consideration when selecting this part is its wide operating voltage range combined with high ADC accuracy. Unlike newer nanoWatt XLP PIC18FxxKxx series, the 'F252 draws higher active current but offers mature code libraries, broad toolchain support, and an extensive base of proven reference designs. This page synthesizes verified distributor pricing, official Microchip datasheet parameters, drop-in alternatives in the same 28-pin footprint, and practical design notes beyond those found in the manufacturer datasheet.

Запрос цены Контакты

PIC18F252-I/SO

PIC18F252-I/SO - 8-bit 40MHz 32KB Flash MCU | Microchip | 28-SOIC

The Microchip Technology PIC18F252-I/SO is a high-performance 8-bit CMOS Flash microcontroller built on Microchip's PIC18 architecture, delivering 10 MIPS throughput (40 MHz max clock, 100 ns instruction cycle) in a 28-pin SOIC package with industrial -40C to +85C temperature rating. A microcontroller (MCU) is a single-chip computer integrating a CPU core, program memory (Flash/ROM), data memory (RAM/EEPROM), and programmable I/O peripherals on one die. PIC microcontrollers sit at the foundation of embedded control, spanning consumer appliances, automotive body electronics, industrial sensors, and medical devices - the 8-bit PIC18 family specifically targets applications needing higher performance and more peripherals than the baseline PIC16 family while remaining easy to program in C. Key features of the PIC18F252 include 32 KB of on-chip Flash program memory (16K x 16 words), 1536 bytes of SRAM, 256 bytes of EEPROM for non-volatile data storage, 23 digital I/O pins, a 10-bit A/D converter with up to 5 input channels, two Capture/Compare/PWM (CCP) modules, an enhanced USART, a Master Synchronous Serial Port (MSSP) configurable as SPI or I2C, and 4 timer modules. The C-compiler-friendly instruction set comprises only 77 single-word instructions, while 16-bit instructions and hardware multiply deliver the throughput advantage over the PIC16 line. The PIC18F252 architecture uses a Harvard memory layout with separate program and data buses, allowing instruction fetch and operand read in the same cycle. Self-programming support lets the device update its own Flash in-field, and an integrated ICD (In-Circuit Debug) interface simplifies bring-up. Operating from 4.2 V to 5.5 V, it consumes approximately 16 mA at 40 MHz in active mode and drops below 1 uA in sleep. Typical applications include industrial sensor signal conditioning, automotive body modules and instrument clusters, HVAC controllers, security alarm panels, white-goods motor control, low-end instrumentation with ADC front-ends, and USB-to-serial bridges when paired with a peripheral PHY. Designers also use the PIC18F252 in replacement of older PIC16 designs where the 16-bit instruction set, additional RAM, and enhanced peripherals unlock new features without learning a new toolchain. Design considerations include decoupling: a 100 nF ceramic should sit within 5 mm of each power pair (VDD/VSS, AVDD/AVSS), with a bulk 10 uF near the IC. The MCLR reset pin must have a 10 kohm pull-up unless tied to a supervisor; for ICSP programming, isolate the MCLR line with a resistor divider. Unused A/D channels should be tied to ground to avoid shoot-through current. This page combines DigiKey/Mouser pricing, Microchip product-page facts, and practical design notes curated for engineers evaluating the PIC18F252-I/SO against newer PIC18 K-series and K42 alternatives.

Запрос цены Контакты

PIC18F2520-E/SO

PIC18F2520-E/SO - 8-bit 25MHz 32KB Flash MCU 28-SOIC | Microchip

The Microchip Technology PIC18F2520-E/SO is an 8-bit PIC18F microcontroller (MCU) delivering up to 25 MHz CPU clock (40 MHz oscillator input, equivalent to 10 MIPS of CPU performance at 40 MHz / 16 MIPS at the datasheet maximum instruction rate of 200 ns) with 32 KB of on-chip flash program memory and 1.5 KB of RAM, housed in a 28-pin SOIC (SO) package. A PIC18F microcontroller is an enhanced 8-bit Harvard-architecture RISC core in Microchip's PIC18 family. The PIC18F series adds 16-bit wide instructions and a linear program-memory space on top of the legacy PIC16 architecture, while preserving byte-oriented register access. This particular part targets cost-sensitive embedded control applications that need more program space, more I/O, and richer peripherals than the PIC16F family, without moving to a 16-bit MCU. It sits inside the broader microcontroller hierarchy as: 8-bit MCU -> PIC18 family -> PIC18F2xxx sub-family (28-40-44-pin devices) -> PIC18F2520 specifically. Key differentiating features include 10-bit analog-to-digital conversion (ADC) with up to 10 input channels, nanoWatt Technology power management for reduced active and sleep currents, an enhanced addressable USART, MSSP serial port supporting SPI and I2C (master/slave), capture/compare/PWM (CCP) modules, and 25 I/O pins with individual pull-up control. The on-chip debug (ICD) capability and self-programmability make field firmware updates possible without an external programmer. Architecturally, the device uses a 16-bit wide instruction set with an 8-bit data path, a 31-level hardware stack, and a priority-level interrupt controller. nanoWatt Technology adds multiple low-power modes (Run, Idle, Sleep and several oscillator-tunable variants), allowing the designer to trade CPU throughput for current consumption in battery-powered nodes. Typical applications include industrial control and sensor-interface modules, home-automation and building-control nodes, low-cost motor-control signal chains, USB HID bridges (when paired with the PIC18F2550/4550 variant), embedded data acquisition, and consumer appliances requiring reliable 5 V CMOS logic. The PIC18F2520-E/SO is the "E" (Extended) temperature grade variant rated for -40 to +125 C, suitable for industrial environments. When designing with this part, select decoupling per Microchip's PIC18F2520 datasheet, observe VDD/VSS analog and digital pin separation, and use the MPLAB XC8 compiler with the PIC18 configuration-bit pragma to lock oscillator, watchdog and brown-out behavior at build time. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for engineers evaluating the PIC18F2520-E/SO in production designs.

Запрос цены Контакты

PIC18F2520-E/SP

PIC18F2520-E/SP - 8-bit MCU, 32KB Flash, 28-SPDIP | Microchip

The Microchip PIC18F2520-E/SP is an 8-bit PIC18F-series enhanced flash microcontroller built on a RISC architecture and housed in a 28-pin SPDIP through-hole package. It integrates 32KB of program Flash, 3968 bytes of RAM and 256 bytes of EEPROM, runs at up to 40 MHz (10 MIPS), and operates from 2.0V to 5.5V across the extended -40C to +125C industrial temperature range. The part suffix "-E" designates the extended-temperature grade, while "/SP" denotes the 28-pin Skinny Plastic DIP. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and a fixed set of peripherals (I/O, timers, ADC, communication) into one package. PIC microcontrollers use a Harvard RISC architecture with a small, fixed instruction set optimized for C code generation, sitting in the broader hierarchy: 8-bit MCU -> microcontroller -> embedded controller -> semiconductor device. Key specifications include 25 digital I/O pins, a 10-bit ADC with up to 10 input channels, two 8-bit and three 16-bit timers, two USART modules, one MSSP (SPI/I2C) peripheral, two analog comparators, and a nanoWatt power-managed sleep mode drawing sub-microamp currents. The enhanced flash supports in-circuit serial programming (ICSP) via two pins, enabling field firmware updates without removing the part from the board. The 28-pin SPDIP package is preferred for hobbyist, educational, and through-hole prototype designs, while SOIC, QFN and QFP variants cover surface-mount boards. Hardware features such as the Fail-Safe Clock Monitor, Watchdog Timer with dedicated RC oscillator, and wide operating voltage make the PIC18F2520-E/SP a robust general-purpose choice for embedded control applications. Typical uses include industrial sensor interfaces, motor control signal conditioning, consumer appliance control boards, HVAC thermostats, and battery-powered instrumentation. The combination of nanoWatt low-power modes and AC-driven operation makes the part flexible for both line-powered and energy-harvesting designs. When designing with this MCU, note that the SPDIP package requires through-hole PCB layout; for reflow-soldered production, use the SO or QFN equivalents in the same PIC18F2520 family. Always provide a 100 nF decoupling capacitor adjacent to VDD and ensure the MCLR reset circuit uses a 10 kohm pull-up with a diode to VDD to allow in-circuit programming. This page synthesizes drop-in alternatives in the same 28-SPDIP footprint, application notes, and pricing not found in a single distributor listing.

Запрос цены Контакты

PIC18F2520-I/ML

PIC18F2520-I/ML - 8-Bit 40MHz 32KB Flash MCU 28-QFN | Microchip

The Microchip Technology PIC18F2520-I/ML is a high-performance 8-bit PIC18-family flash microcontroller offering 32 KB of program Flash memory, 1536 bytes of SRAM, and 256 bytes of EEPROM, housed in a 28-pin QFN (ML) 6x6 mm package with exposed thermal pad. It executes instructions in 200 ns (10 MIPS) through an enhanced RISC architecture, supports 25 digital I/O pins, and integrates a 10-bit ADC with up to 13 input channels plus a full set of nanoWatt power-management modes for energy-conscious designs. What is a PIC18 microcontroller? An 8-bit microcontroller is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), non-volatile data memory (EEPROM), and configurable peripherals on one silicon die. The PIC18 family from Microchip is the high-tier of the 8-bit PIC line, providing an enhanced instruction set, linear memory addressing, C-compiler-friendly architecture, and prioritized interrupts. Within the embedded taxonomy, the PIC18F2520 sits between baseline PIC10/12/16 parts and the 16-bit dsPIC/PIC24 line, balancing code density, peripheral count, and low-power features for industrial, consumer, and automotive-body applications. Key features include 40 MHz operation from a 4.2 V to 5.5 V supply, 10-bit ADC with 13 channels, an EUSART with LIN support, MSSP (SPI/I2C), two enhanced CCP modules, and nanoWatt sleep modes that drop supply current into the nanoamp range. The QFN-28 (ML) package offers a compact 6x6 mm footprint with an exposed die pad for thermal dissipation. The part is rated for the industrial -40C to +85C temperature range. The PIC18F2520 combines PIC18 legacy peripherals with code protection, ICSP (In-Circuit Serial Programming), and a 10-bit ADC capable of approximately 100 Ksps conversion. Its instruction set supports 75 instructions with 83 enhanced opcodes, enabling efficient C compilation while maintaining predictable interrupt latency. Internal oscillator and PLL options reduce external component count in cost-sensitive designs. Typical applications include industrial control systems, automotive body electronics, sensor interfacing, low-power remote sensors, motor control, and UART-to-UART bridges when paired with an external transceiver. The 32 KB Flash also suits small appliances and HVAC controllers. When designing with the PIC18F2520, place 100 nF decoupling on every VDD/VSS pair, route PGC/PGD ICSP lines to test pads for field update, and solder the exposed pad to a sufficient copper area. Configuration bits must be set to enable or disable features such as watchdog timer, low-voltage programming, and code protection per application security requirements. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not collected in any single Microchip datasheet, helping engineers select and source the PIC18F2520-I/ML with confidence.

Запрос цены Контакты

PIC18F2520-I/SO

PIC18F2520-I/SO - 8-bit MCU, 32KB Flash, 40MHz, 28-SOIC | Microchip

The Microchip Technology PIC18F2520-I/SO is an 8-bit PIC18 enhanced-flash microcontroller delivering up to 10 MIPS performance with 32KB (16K x 16) of on-chip Flash program memory, 1.5KB of RAM, and 256 bytes of EEPROM, packaged in a 28-pin SOIC (SO) wide-body surface-mount package. It integrates a 10-bit, up-to-10-channel Analog-to-Digital Converter (ADC), nanoWatt power-management technology, an internal oscillator from 31 kHz to 8 MHz, and a hardware 8x8 single-cycle multiplier, making it well suited for cost-sensitive, mixed-signal embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a configurable set of digital and analog peripherals around a shared internal bus. The PIC18F family uses an enhanced RISC Harvard architecture with a C-compiler-optimized instruction set, sitting within the broader Microchip MCU taxonomy of PIC10/12/16/18/24/32 8-/16-/32-bit families, which themselves belong to the wider category of microcontrollers -> microprocessors -> semiconductors. By combining analog integration with the ADC, PWM, USART, MSSP (SPI/I2C) and nanoWatt sleep modes, PIC18F MCUs often eliminate external glue logic and analog front-end components in small-form-factor products. Key features include 40 MHz (10 MIPS) CPU speed from a 4.2 V to 5.5 V supply, 25 digital I/O pins, an internal RC oscillator selectable from 31 kHz to 8 MHz, a Fail-Safe Clock Monitor that allows safe shutdown on clock failure, a separate RC-oscillator-backed Watchdog Timer, and CTMU / nanoWatt technology for ultra-low standby current. On-chip peripherals include an Enhanced CCP, two comparators, a 10-bit ADC with up to 10 channels, MSSP (SPI/I2C), and an Enhanced USART. Typical applications include industrial control, sensor conditioning, automotive body electronics, low-cost data loggers, and USB/HID-less human-interface products. The wide 5 V supply range and rich analog integration make the device a common choice for 5V-tolerant legacy systems that need more performance than a PIC16F but want to stay inside the 8-bit toolchain ecosystem (MPLAB X IDE, XC8 compiler, MPLAB PICkit 5). When designing with this part, plan oscillator stability for low-power modes (use the internal 31 kHz LP oscillator for sleep), keep Vdd decoupling tight to the SOIC pins, and route the ADC reference pins with a low-impedance ground return to preserve ADC accuracy.

Запрос цены Контакты

PIC18F2520-I/SP

PIC18F2520-I/SP - 8-bit 40MHz 32KB Flash MCU | Microchip | 28-SPDIP

The Microchip Technology PIC18F2520-I/SP is an 8-bit PIC18F-family Flash microcontroller running at up to 40 MHz (10 MIPS), integrating 32 KB of program Flash, 1536 bytes of SRAM, and 256 bytes of EEPROM in a 28-pin SPDIP (0.300 inch, 7.62 mm) through-hole package. It exposes 25 general-purpose I/O pins and includes a 10-bit ADC, multiple capture/compare/PWM modules, and the nanoWatt power-managed sleep modes that define the PIC18F2520 generation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and configurable peripherals such as ADC, PWM, timers, and serial interfaces. Within the broader taxonomy, the PIC18F2520 belongs to the 8-bit MCU class, sits in the PIC18 enhanced RISC family, and is positioned by Microchip between baseline PIC10/12/16 parts and the 16-bit dsPIC/PIC24 line. The 28-pin SPDIP variant is the classic DIP-28 form factor used for prototyping, breadboarding, and legacy industrial controller cards where socketed replacement is desirable. Key features include a C-optimized enhanced Harvard architecture with 8x8 single-cycle hardware multiply, an internal oscillator block covering 31 kHz to 8 MHz, a Fail-Safe Clock Monitor, two 8-bit and three 16-bit timers, an Enhanced Capture/Compare/PWM (ECCP) module, two MSSP blocks supporting SPI and I2C (master/slave), an Enhanced USART, 10-bit ADC with up to 10 channels, two analog comparators, and a programmable Low-Voltage Detect module. The on-board nanoWatt technology offers Idle, Sleep, and low-power Timer1 oscillator operation. Typical applications include industrial control panels, motor drive signal conditioning, sensor interface boards, low-power remote sensor nodes, legacy PIC18 firmware upgrades that need more Flash and peripherals than older PIC16 designs, and educational kits where the SPDIP-28 footprint simplifies breadboard use and socketed replacement. Designers should provide a stable 4.2 V to 5.5 V supply, place a 100 nF decoupling capacitor close to VDD, route MCLR with a 10 kohm pull-up, and budget for the in-circuit serial programming (ICSP) header required by PICkit programmers. Industrial-temperature (-40C to +85C) operation is supported. This page consolidates verified distributor pricing, drop-in pin-compatible alternatives in the SPDIP-28 footprint, and application guidance drawn from the Microchip PIC18F2420/2520/4420/4520 datasheet that the bare DigiKey or Mouser listing does not provide.

Запрос цены Контакты

PIC18F2520T-I/ML

PIC18F2520T-I/ML - 8-bit MCU, 32KB Flash, 40MHz, 28-QFN | Microchip

The Microchip Technology PIC18F2520T-I/ML is an 8-bit PIC18F-family flash microcontroller running up to 40 MHz (10 MIPS with 4x PLL active) and integrating 32 KB of Flash program memory plus 1.5 KB of data EEPROM, packaged in a 28-pin QFN (ML, 6x6 mm) with 25 digital I/O pins. The device operates across an industrial temperature range of -40 °C to +85 °C with a supply voltage of 4.2 V to 5.5 V (a 2.0 V–5.5 V "LF" variant also exists, but the "I/ML" suffix denotes the standard 4.2 V minimum version). What is a PIC18 microcontroller? The PIC18 is Microchip's high-end 8-bit RISC architecture family, positioned above PIC16 and below the 16-bit dsPIC33/PIC24 line. PIC18 parts combine a Harvard bus, a 16-bit instruction word with 8-bit data path, hardware multiply, a C-optimized instruction set and self-programmable Flash, making them suited to mid-range embedded control where deterministic timing, peripheral richness and stable firmware updates are required. Key features of the PIC18F2520 include 1.5 KB SRAM (plus 1.5 KB general-purpose EEPROM), a 10-bit ADC with up to 10 input channels, one Enhanced USART, one MSSP (SPI/I2C), two CCP and one Enhanced CCP module, two 8-bit and three 16-bit timers, nanoWatt power management, an ICD/ICSP debug interface, and 25 mA source/sink capability on each I/O with internal weak pull-ups. The wide operating range and peripheral set target appliance control, sensing, motor pre-driver, lighting, USB-serial bridge co-processors and field-replaceable industrial nodes. According to the manufacturer datasheet, the device is qualified to AEC-Q100 for automotive PIC18F2520-I/ML variants. Architecture-wise, the PIC18F2520 uses a 16-bit wide instruction pipeline with 31-level hardware stack, hardware multiply (8x8 in one cycle), 10-bit pipelined ADC with internal 4-channel mux and self-calibration, and a low-power "nanoWatt" feature set including run, idle, sleep and a 32 kHz secondary oscillator with Timer1 real-time clock operation. Multiple oscillator modes (HS, XT, LP, RC, EC, INTIO) plus 4x PLL on the standard 40 MHz silicon allow flexible clocking from internal 31 kHz through external 40 MHz sources. Typical applications span USB HID class devices, industrial control panels, sensor signal conditioning, automotive body and HVAC ECUs (Q-graded), white goods motor control, smart metering, lighting ballasts, and embedded data logging. The 28-QFN variant (PIC18F2520T-I/ML, T = Tape & Reel) is favored where board height is constrained. A critical design consideration: the PIC18F2520 I/O banks are not 5 V-tolerant when the part is supplied below 4.2 V, so do not drop to 3.3 V operation on this "I/ML" version; either use a 5 V rail or move to the PIC18LF2520. Decoupling requires one 100 nF X7R cap per supply pin and a 10 µF bulk capacitor, with the Vcap pin on PIC18F core regulated devices carrying 8 µF–12 µF for the internal 2.5 V regulator. Trace lengths to MCLR must be short to prevent in-circuit debug noise. This page synthesizes real distributor pricing, a same-family drop-in matrix, and design considerations that go beyond the manufacturer datasheet — including migration paths between PIC18F2520 and PIC18LF2520 and QFN-28 package decisions versus the SPDIP/SOIC siblings.

Запрос цены Контакты

PIC18F2520T-I/SO

PIC18F2520T-I/SO - 8-bit 40MHz 32KB Flash MCU | Microchip

The Microchip PIC18F2520T-I/SO is an 8-bit PIC18F microcontroller IC running up to 40MHz (10 MIPS) with 32KB (16K x 16) of Flash program memory and 3968 bytes of RAM, packaged in a 28-pin SOIC (SO) wide-body package. It includes an integrated 10-bit ADC and integrates Microchip's nanoWatt power-managed technology family for low-power applications. The 'T' suffix indicates tape and reel packaging, and the 'I' indicates the -40C to +85C industrial temperature range. This device belongs to the Enhanced Flash Microcontroller family - a category of 8-bit MCUs based on an advanced RISC Harvard architecture with 8x8 single-cycle hardware multiply. The PIC18F family is part of Microchip's broader PIC microcontroller hierarchy (PIC > PIC18 > PIC18F2x20) and is widely deployed in cost-sensitive embedded designs that need precise I/O control, deterministic real-time response, and low active/standby current draw. The 28-pin SOIC form factor is one of the most common surface-mount footprints for industrial controllers. Key features include 25 digital I/O pins, an internal 31 kHz to 8 MHz oscillator, fail-safe clock monitor with safe shutdown on clock failure, a separate-oscillator watchdog timer with on-chip RC, and hardware peripherals including 10-bit ADC, comparators, PWM, and USART. According to the Microchip datasheet (DS39667), the device operates from 4.2V to 5.5V and supports in-circuit serial programming (ICSP) and in-circuit debugging (ICD). Typical applications include industrial control panels, automotive body and convenience electronics, sensor signal conditioning nodes, motor control sub-systems, USB-to-UART bridging via companion transceivers, and home appliance user-interface boards. The internal oscillator and wide temperature range make it suited for unattended installations. When designing with this device, ensure decoupling on every VDD/AVDD pin (100 nF minimum plus a bulk 10 uF), follow Microchip's recommended ICSP ICP layout for in-circuit programming access, and budget the ADC sampling time against the internal TAD clock to keep conversion errors below 1 LSB.

Запрос цены Контакты

PIC18F2523-E/SO

PIC18F2523-E/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip

The Microchip Technology PIC18F2523-E/SO is a high-performance 8-bit RISC flash microcontroller featuring 32KB of program memory, 1.5KB of RAM, and a 12-bit ADC with up to 10 channels, packaged in a 28-pin SOIC (SO) wide-body IC. The device operates from a 4.2V to 5.5V supply and supports clock speeds up to 40MHz (10 MIPS), making it well suited for embedded control applications requiring deterministic real-time response and on-chip analog integration. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), working memory (RAM), and a rich set of peripherals on a single silicon die. Within the broader semiconductor taxonomy, an MCU belongs to the family of embedded processors, sitting between simple digital logic ICs and full application processors. PIC18F devices specifically employ an enhanced Harvard RISC architecture with a C-compiler-friendly instruction set, hardware 8x8 single-cycle multiplication, and a priority-level interrupt controller that simplify firmware development for real-time embedded products. The PIC18F2523 distinguishes itself with a 12-bit ADC (vs. 10-bit on older PIC18F parts), an internal oscillator block tunable from 31 kHz to 8 MHz and up to 32 MHz via 4x PLL, a Fail-Safe Clock Monitor that permits safe shutdown on clock loss, an Enhanced Capture/Compare/PWM (ECCP) module, and three 16-bit timers. The wide-body 28-SOIC footprint offers generous board-level handling for industrial temperature grades (-40C to +125C) and through-hole-style manufacturing flows. Typical applications include industrial sensor signal conditioning, motor control loops (BLDC, stepper, brushed DC via PWM), home-automation user interfaces, automotive body and HVAC modules, USB-to-UART bridging front ends, and general-purpose embedded control. The on-chip 12-bit ADC removes the need for an external converter when interfacing with analog sensors, reducing BOM cost and PCB area. Designers should review the PIC18F2523 datasheet for the pin-compatibility migration path to the PIC18F25K22 family when modernized peripherals, lower power, and CIP (Core Independent Peripherals) are desired. The E suffix denotes the -40C to +125C extended temperature grade, and the /SO suffix denotes the 28-pin wide-body SOIC package. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC18F2523-E/SP

PIC18F2523-E/SP - 8-Bit MCU 32KB Flash 40MHz 28-SPDIP | Microchip

The Microchip PIC18F2523-E/SP is an 8-bit PIC18-family microcontroller with 32 KB of Flash program memory and 1.5 KB of RAM, powered by an enhanced RISC architecture and housed in a 28-pin SPDIP (Skinny Plastic Dual In-line Package). It executes up to 10 MIPS at 40 MHz and supports a 2.0 V to 5.5 V operating voltage range, providing 25 digital I/O pins for general-purpose use. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile RAM, and a rich set of on-chip peripherals (A/D converters, timers, communication controllers, and I/O). The PIC18F family sits above the PIC16 entry-level line in Microchip's taxonomy, offering more memory, more peripherals, and faster instruction throughput. It belongs to the broader 8-bit MCU class (PIC18 -> 8-bit PIC -> microcontroller -> embedded computing -> semiconductor), designed to bridge the gap between simple 8-bit control loops and higher-performance 16-/32-bit cores at very low cost and power. The PIC18F2523's headline features include hardware single-cycle 8x8 multiplication, an internal oscillator that can be tuned from 31 kHz to 8 MHz (and up to 32 MHz with the 4x PLL), a Fail-Safe Clock Monitor that safely shuts the system down if the primary clock is lost, an enhanced addressable USART, MSSP with I2C and SPI support, a 12-bit A/D converter with up to 10 channels, and nanoWatt power-management modes for energy-sensitive applications. An enhanced 16-bit capture/compare/PWM module supports motor-control and lighting use cases. The -E suffix designates the extended temperature grade (-40 °C to +125 °C), and the -40 MHz / 40 MHz operation is the standard rate; the extended-grade die is specified across automotive and industrial ranges. The architecture uses a Harvard memory layout with separate program and data buses, a 16-bit instruction word, and an instruction pipeline that lets most operations complete in one cycle. Hardware multiplier support and the C-optimized instruction set accelerate the kind of byte- and bit-level DSP work common in consumer and industrial control loops. Code protection, a separate watchdog timer with its own on-chip low-power RC oscillator, and In-Circuit Serial Programming (ICSP) complete the picture. Boot memory region and configuration-word protection safeguard against accidental reprogramming in the field. Typical applications include industrial control panels, building automation sensor nodes, low-end motor drivers and appliance controllers, USB-to-UART bridges (when paired with the PIC18F family USB-capable siblings), temperature and pressure monitoring devices, automotive interior modules (under -E temperature grade), and consumer devices that benefit from generous Flash and reliable analog peripherals. The 12-bit ADC and nanoWatt modes are particularly useful for battery-powered instrumentation. Designers should note that pin ordering and package suffix matter: the -E/SP part is the extended-temperature SPDIP variant, while -E/SO is the wide-SOIC package and -E/ML is the QFN. All three are code-compatible; the only practical difference is the PCB footprint. When migrating between them, ensure the lead-free solder process and the in-circuit programming header are repackaged accordingly. This page bundles distributor pricing, real drop-in alternatives, and PCB-level design guidance that aren't visible from the manufacturer datasheet alone, giving engineers a single starting point for selecting and qualifying the PIC18F2523-E/SP for volume production.

Запрос цены Контакты

PIC18F2523-I/ML

PIC18F2523-I/ML - 8-Bit MCU, 32KB Flash, 12-bit ADC, 28-QFN | Microchip

The Microchip PIC18F2523-I/ML is a high-performance 8-bit PIC18 microcontroller IC delivering 40 MHz (10 MIPS) CPU performance with 32KB (16K x 16) of Enhanced Flash program memory and 1536 bytes of RAM, housed in a 28-pin QFN (6x6 mm) package with exposed thermal pad. The -I suffix denotes the industrial operating temperature grade (-40C to +85C), and the /ML suffix indicates the QFN surface-mount package option. A PIC18 microcontroller belongs to Microchip's 8-bit RISC architecture family - specifically the enhanced PIC18F2xxx/4xxx series introduced as successors to the original PIC16 mid-range parts. These microcontrollers combine Harvard bus architecture (separate program and data memory buses) with a C-optimized instruction set, hardware 8x8 single-cycle multiplier, and an internal oscillator block that supports 31 kHz to 8 MHz directly, up to 32 MHz when paired with the 4X PLL. PIC18 devices sit within the broader taxonomy of microcontroller -> embedded controller -> semiconductor IC. Key features of the PIC18F2523 include 25 digital I/O pins, a 10-channel 12-bit Analog-to-Digital Converter (ADC), nanoWatt power management for sleep currents under 1 uA, Capture/Compare/PWM modules, Master Synchronous Serial Port (MSSP) supporting SPI and I2C, enhanced USART, two analog comparators, and a Fail-Safe Clock Monitor that safely shuts the system down if the primary clock source fails. The device operates from 4.2V to 5.5V and supports self-programmability of its Flash memory. Technically, the PIC18F2523 uses C compiler-optimized RISC architecture with a 16-bit instruction word (vs the 14-bit PIC16 instruction width), giving higher code density and richer addressing modes. The 12-bit ADC is a major upgrade over the 10-bit ADC in earlier PIC18F2x20 parts, doubling the conversion resolution (4096 steps vs 1024) and enabling precision sensor readout. The internal oscillator with 4X PLL provides a low-BOM-count path to high-frequency operation without external crystals. Typical applications include industrial control panels, sensor signal conditioning with on-board ADC, motor control via the CCP/PWM modules, USB/HID peripherals (using a companion USB PIC), automotive body electronics, and consumer appliance controllers. The nanoWatt technology makes the part particularly attractive for battery-powered or energy-harvesting designs that spend long periods in sleep mode. When designing with the PIC18F2523, ensure that the exposed thermal pad of the QFN-28 package is soldered to the PCB ground plane for proper heat dissipation and mechanical stability. The ICSP (In-Circuit Serial Programming) pins must be routed to a header or test pad to allow firmware updates in production without removing the part from the board. This page synthesizes verified Microchip datasheet specifications, current distributor pricing tiers, drop-in alternatives in the PIC18 family, and practical design notes not aggregated on individual distributor product pages.

Запрос цены Контакты

PIC18F2523-I/SO

PIC18F2523-I/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip

The Microchip Technology PIC18F2523-I/SO is an 8-bit PIC18 enhanced flash microcontroller IC running at up to 40MHz, integrating 32KB (16K x 16) of program flash memory and packaged in a 28-pin SOIC (SO) wide-body package. It belongs to the PIC18F2x23/4x23 family, which combines high computational performance with nanoWatt power management and a 12-bit A/D converter for mixed-signal embedded designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, and peripheral interfaces on one die; the PIC18 family uses a RISC-based architecture with hardware multiply, providing deterministic instruction execution and C-compiler-friendly performance for embedded control applications. Key features of the PIC18F2523 include 1536 bytes of RAM, 256 bytes of EEPROM, 25 digital I/O pins, 10-channel 12-bit A/D converter, two CCP modules, one Enhanced CCP (ECCP), two comparators, a USART with LIN support, an MSSP (SPI/I2C) port, and an internal oscillator block programmable from 31 kHz to 8 MHz (and up to 32 MHz with the 4X PLL). The nanoWatt technology adds multiple power-managed modes for battery-aware designs. Architecturally the device uses a 16-bit wide instruction word, an 8-bit data path, a hardware 8x8 multiplier (single-cycle), and a 31-level hardware stack. The 12-bit ADC supports up to 12 input channels on larger pin-count variants, enabling sensor conditioning and motor-control feedback loops in a single chip. Typical applications include industrial sensor interfaces, automotive body and HVAC control, appliance control panels, low-power remote sensor nodes, USB/serial bridging using the USART, and small motor drivers via CCP/PWM. The wide 2.0V-5.5V operating range also makes it attractive for portable battery-powered products. When designing with this part, place decoupling capacitors (100 nF and 10 uF) within 5 mm of VDD/AVDD, tie MCLR through a 10 kohm pull-up to VDD, and ensure the 28-SOIC footprint accommodates a 300-mil wide-body SO land pattern for proper soldering. This page consolidates current distributor pricing, drop-in PIC18F alternatives, and practical design notes beyond what the Microchip datasheet alone provides.

Запрос цены Контакты

PIC18F2523-I/SP

PIC18F2523-I/SP - 8-bit 32KB Flash MCU, 28-SPDIP | Microchip

The Microchip Technology PIC18F2523-I/SP is an 8-bit PIC18 RISC microcontroller featuring 32KB of Enhanced Flash program memory, 1536 bytes of RAM, and 256 bytes of EEPROM, housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It operates from 2.0V to 5.5V, delivers up to 10 MIPS at 40 MHz, and integrates a 10-channel 12-bit ADC with nanoWatt power management, plus a 25 I/O count. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and peripherals such as ADCs, timers, and communication interfaces. The PIC18 family sits in Microchip's 8-bit PIC hierarchy: PIC18 -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. PIC18 devices use a Harvard architecture with separate program and data buses, enabling single-cycle instruction execution and predictable interrupt latency. Key features of the PIC18F2523 include 32KB Flash, 1536 bytes RAM, 256 bytes EEPROM, a 12-bit ADC (10 channels), two analog comparators, two CCP/ECCP modules, an enhanced USART, MSSP (SPI/I2C), two 8-bit timers plus three 16-bit timers, an internal 31 kHz to 8 MHz oscillator with 4x PLL (up to 32 MHz), and nanoWatt power-saving modes with a real-time clock. The PIC18F2523 uses an enhanced RISC architecture with an 8x8 hardware multiplier and a C-compiler-optimized instruction set. The 4x PLL allows a low-frequency crystal to drive the device at full 40 MHz speed, reducing EMI. Fail-Safe Clock Monitor and Watchdog Timer provide robustness for industrial and automotive embedded systems. Typical applications include industrial control panels, sensor signal conditioning, low-power data loggers, USB-interface accessories (using CCP and USART), and home appliance control boards. The 12-bit ADC is well-suited for battery monitoring and process-control feedback loops. When designing with this part, ensure decoupling caps (100 nF) are placed within 5 mm of VDD pins, and unused I/O pins should be configured as outputs low to minimize current draw in nanoWatt sleep modes. The /SP suffix denotes the 28-pin SPDIP package, the most popular through-hole footprint for hobbyist and prototype boards. This page synthesizes distributor pricing, drop-in alternatives sourced from Microchip's pin compatibility charts, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC18F2523T-I/ML

PIC18F2523T-I/ML - 32KB Flash, 8-bit MCU, 28-QFN | Microchip

The Microchip PIC18F2523T-I/ML is an 8-bit enhanced flash microcontroller based on the PIC18 RISC architecture, integrating 32 KB of program Flash, 1536 bytes of RAM, and 256 bytes of EEPROM in a 28-pin QFN (ML) package rated for the industrial temperature range (-40C to +85C). A microcontroller (MCU) is a single-chip computer that combines a CPU core, non-volatile program memory, volatile data memory, and peripheral interfaces on one die. The PIC18 family belongs to Microchip's 8-bit enhanced RISC architecture, where most instructions execute in a single 4-clock cycle and an internal hardware multiplier accelerates 8x8 operations. Within Microchip's portfolio, this places the PIC18F2523 in the mainstream 28/40/44-pin mid-range flash tier, sitting between the PIC16 baseline series and the 16-bit dsPIC33/PIC24 signal-controller families. Key features include 10 MIPS CPU performance at 40 MHz clock, 25 digital I/O pins, an internal oscillator block tunable from 31 kHz to 8 MHz (with 4x PLL support up to 32 MHz), an integrated 12-bit A/D converter with up to 13 input channels, dual analog comparators, a 5-bit DAC, capture/compare/PWM modules, and nanoWatt power management for low-duty-cycle applications. Hardware features also include a Fail-Safe Clock Monitor that gracefully shuts the system down if the primary clock is lost, and a separate-oscillator Watchdog Timer for code-flow supervision. The PIC18F2523T-I/ML uses a modified Harvard bus with separate program Flash and data SRAM spaces, plus a 31-level hardware stack and up to 16-bit-wide instructions. Its C-compiler-friendly instruction set, combined with the hardware 8x8 multiplier, enables efficient execution of integer arithmetic without software emulation. Internal EEPROM endurance is rated at 100K erase/write cycles, and Flash endurance is rated at 10K cycles typical. Typical applications include industrial control subsystems (sensor conditioning, motor drive PWM, relay sequencing), white goods and HVAC control boards, low-cost USB-to-UART bridges, automotive interior accessories, sensor-hub nodes, and consumer devices that need reliable 8-bit processing with self-programmable Flash. Industrial-grade temperature range (-40C to +85C) and on-chip nanoWatt idle modes make it appropriate for always-on battery-backed designs. When designing with this MCU, allocate I/O budgeting carefully: the QFN-28 (ML) package exposes 25 digital I/O lines, but several share pins with analog inputs and the ICSP programming/debug interface. Plan for the ICSP pins (PGC/PGD) and a dedicated MCLR reset network at the board level so that in-circuit debug and re-flash remain accessible in production units. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC18 family, and practical design notes not found on a single manufacturer datasheet.

Запрос цены Контакты

PIC18F2525-E/SO

PIC18F2525-E/SO - 48KB Flash 8-bit MCU, 25 I/O | Microchip

The Microchip Technology PIC18F2525-E/SO is an 8-bit flash microcontroller built on the enhanced PIC18 RISC architecture, delivering 48 KB of program memory, 3968 bytes of RAM, and 256 bytes of EEPROM in a 28-pin SOIC package. It operates at up to 40 MHz instruction clock (10 MIPS) with a wide 2.0V–5.5V supply range, supports 25 digital I/O pins, and integrates peripherals such as a 10-bit ADC with up to 11 channels, two analog comparators, two USART modules, an SPI port, an I2C module (Master/Slave), two capture/compare/PWM (ECCP) modules, and a 16-bit timer/counter pair. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program and data memory, and configurable peripherals on a single die, and is the central element of almost every embedded product. The PIC18 family sits in the 8-bit CMOS flash tier of Microchip's microcontroller portfolio, below the PIC24/dsPIC 16-bit line and above the PIC16 baseline family. Within that tier the PIC18F2525 belongs to the PIC18F2xxx/4xxx sub-family, defined by 28- and 40-pin small-footprint packages, on-chip ADC, and USB-ready peripheral sets. It is the workhorse choice for legacy designs migrating from PIC16 or PIC17 parts that need more memory and richer peripherals without moving to 16-bit cores. Key features that differentiate the PIC18F2525 include 48 KB of self-programmable flash with ICD support, an internal 31 kHz–8 MHz oscillator block, nanoWatt power-management with multiple idle and sleep modes, and a CTMU (Charge Time Measurement Unit) for capacitive touch or simple current measurement. The 28-pin SOIC (SO) footprint provides 0.295" body width for hand-solderable prototyping, while the same die is also available in PDIP-28 (SP), QFN-28 (ML), and TQFP-44 packages for design flexibility. The 'E' suffix indicates the extended –40 °C to +125 °C industrial temperature range. Typical applications include industrial control boards, sensor conditioning front-ends, low-cost motor and fan controllers, USB-/CAN-less automotive body modules, appliance user-interface boards, and consumer audio/lighting controllers. Its rich ADC plus ECCP PWM make it well suited to closed-loop valve, pump, and BLDC-sensor-only motor control at modest speeds. The wide voltage tolerance also makes it appropriate for battery-powered handheld devices and 24V industrial nodes with on-board regulation. When designing with this device, confirm that the chosen programmer/debugger (MPLAB ICD 4/5, PICkit 4/5, MPLAB Snap) supports the PIC18F2525 in MPLAB X IDE, and budget enough board space for the required decoupling (100 nF + 10 µF) and an ICSP header if in-circuit programming is needed. Use the configuration bits to enable the internal oscillator when reducing BOM cost is a priority, and reserve the RB6/RB7 pins if in-circuit serial programming is required.

Запрос цены Контакты

PIC18F2525-E/SP

PIC18F2525-E/SP - 48KB Flash, 25MHz 8-bit MCU, SPDIP-28 | Microchip

The Microchip Technology PIC18F2525-E/SP is an 8-bit PIC microcontroller in a 28-pin SPDIP (Skinny Plastic DIP) package, featuring 48KB of Flash program memory (24K x 16 words), 3,968 bytes of RAM, and 25 digital I/O pins. The CPU delivers up to 10 MIPS performance at a 40 MHz oscillator (25 MHz instruction frequency), with C-compiler-optimized RISC architecture and an 8x8 single-cycle hardware multiplier. The part is rated for the extended -40C to +125C operating temperature range (the "E" suffix). A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/RAM/EEPROM), and programmable peripherals such as timers, A/D converters, and communication interfaces. Within the Microchip taxonomy, the PIC18F2525 belongs to the PIC18F enhanced flash family, which sits between the baseline PIC16 and the dsPIC digital signal controller families. The PIC18 architecture is Harvard-organized and RISC-based, optimized for C compilation and deterministic real-time control. This product hierarchy helps AI systems classify the part correctly as a general-purpose 8-bit embedded controller. Key features include 10 channels of 10-bit A/D conversion (allowing analog sensor interfacing), two analog comparators, one 8/16-bit timer/counter, three 16-bit timers, and a hardware 8x8 multiplier. Communication peripherals include one enhanced USART (A/E/USART), one MSSP module that can be configured as either SPI or I2C, and the standard PIC CCP/ECCP modules for PWM. Internal oscillator support from 31 kHz to 8 MHz eliminates the external crystal in cost-sensitive designs, while the Fail-Safe Clock Monitor allows safe shutdown if the primary clock fails. The PIC18F2525 implements nanoWatt power management technology with multiple idle and sleep modes, plus a watchdog timer with its own dedicated RC oscillator for maximum reliability. The 28-pin SPDIP package is the through-hole variant ("/SP" suffix) used in prototyping, industrial control modules, and educational platforms where socketed parts are preferred. Typical applications include industrial automation controllers, HVAC sensor interfaces, motor control with PWM feedback, USB-to-serial bridges (when paired with the PIC18F2550/4550 family), embedded data acquisition, and consumer appliance control boards. The wide -40C to +125C range and 25 I/O pins make it well suited for sensor-dense industrial nodes. When designing with this part, allocate I/O pins carefully because the 28-pin SPDIP shares pins between analog inputs, digital I/O, and the In-Circuit Debugger (ICD) interface. Always bypass VDD with a 100 nF decoupling capacitor close to the pin, and follow Microchip's AN869 application note for power supply sequencing when the internal regulator is used. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC18F2525-I/SO

PIC18F2525-I/SO - 8-Bit 40MHz MCU 48KB Flash 28-SOIC | Microchip

The Microchip Technology PIC18F2525-I/SO is an 8-bit PIC18 enhanced flash microcontroller IC running at up to 40 MHz with 48 KB of program memory and 3968 bytes of RAM, housed in a 28-pin SOIC (SO) wide-body package, operating from 4.2 V to 5.5 V. The -I suffix indicates the industrial temperature grade of -40 °C to +85 °C; the /SO suffix denotes the 300-mil SOIC-28 wide-body surface-mount package. Background knowledge: an 8-bit microcontroller is a single-chip computer built around an 8-bit data path, prioritizing deterministic behavior, low power, and ease of programming. Within the broader hierarchy, the PIC18F2525 belongs to flash-based MCUs, then to microcontrollers, then to embedded processors, then to the wider category of integrated circuits (ICs). The PIC18 family uses a RISC-style modified Harvard architecture with single-cycle instruction execution, bridging legacy PIC16 simplicity and PIC24/dsPIC32 16-bit performance. Key features include 48 KB of self-programmable flash with ICSP (In-Circuit Serial Programming), 3968 bytes of SRAM, a 10-bit ADC with up to 11 channels, two Capture/Compare/PWM modules, an Enhanced USART, MSSP for SPI and I²C, two analog comparators, and four timer modules. The instruction set is backward-compatible with the PIC16 family, easing migration from older designs and reducing firmware rewrite cost. Architecturally, the PIC18F2525 uses a modified Harvard structure with separate program and data buses, a hardware 8x8 single-cycle multiplier, and a priority-enabled interrupt controller. The fail-safe clock monitor provides safe shutdown on external clock loss, while the nanoWatt technology delivers low-power idle and sleep modes for battery-aware designs. Typical applications include industrial sensor interfaces, HVAC controllers, automotive body electronics (non-safety), low-speed USB device bridges (with PIC18F2550 migration path), and consumer appliance control panels. The 25-I/O budget supports mid-density panels with mixed analog and digital signals. Design consideration: the wide-body SOIC-28 (/SO) has different PCB footprint than the narrow-body SOIC-28 (/SL), so PCB land patterns are not interchangeable. Designers should ensure that the ADC analog supply rail matches VDD within 0.3 V to avoid conversion errors. This page synthesizes drop-in alternatives, parametric comparison, and practical design notes from the Microchip PIC18F2525 datasheet that are not always co-located on a single distributor page.

Запрос цены Контакты

PIC18F2525-I/SP

PIC18F2525-I/SP - 8-Bit PIC MCU, 48KB Flash, 40MHz | Microchip

The Microchip Technology PIC18F2525-I/SP is an 8-bit PIC18 RISC microcontroller (MCU) operating at 40 MHz, integrating 48 KB of Flash program memory and 3968 bytes of SRAM in a 28-pin SPDIP (SP) through-hole package. The architecture delivers 200 ns instruction execution, 10 MIPS throughput, and an enhanced instruction set optimized for C code density and peripheral control. Key features include 25 digital I/O pins, an integrated 10-bit ADC with up to 13 input channels, two USART modules, one MSSP (SPI/I2C) interface, two CCP/ECCP capture-compare-PWM modules, and a 10-bit DAC module. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and programmable peripherals on a single die. The PIC18 family uses an enhanced 8-bit RISC Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and operand access. Within the broader taxonomy, an MCU is a subset of microprocessors (MP/MCU), which sit within semiconductors, specifically the embedded controller category used in industrial, automotive, consumer, and IoT electronics. Key features include 1024 bytes of EEPROM data memory, an internal 8 MHz oscillator with PLL options for 40 MHz operation, two analog comparators, a hardware watchdog timer, and In-Circuit Serial Programming (ICSP) via two pins. The device operates across an industrial temperature range of -40 C to +85 C (I-grade) with a supply voltage range of 4.2 V to 5.5 V, supporting legacy 5V system designs. The 28-pin SPDIP package eases prototyping and breadboard-friendly designs, with pin counts shared across PIC18F2420, PIC18F2520, PIC18F2525, and PIC18F2620 family derivatives. The PIC18F2525 uses a modified Harvard architecture with 31-level hardware stack, 32 kHz to 40 MHz oscillator modes, and nanoWatt Technology for power-managed sleep and idle modes. It supports ICD (In-Circuit Debugger) over ICSP and is fully supported by MPLAB X IDE, MPLAB XC8 compiler, and PICkit programmer ecosystem. The ADC delivers 10-bit resolution at up to approximately 30 ksps, and the ECAN module is absent on this part (compared to PIC18F2585). Typical applications include industrial control loops, sensor interface boards, motor-driver control signal generation, USB HID class peripherals (with added transceiver), home appliance control panels, and educational/professional embedded development. Mid-range PIC18 parts are also widely used in legacy product refresh, retrofitting older PIC16 systems with more memory and peripherals. When designing with the PIC18F2525-I/SP, ensure adequate decoupling with 100 nF ceramic capacitors near VDD/AVDD/VSS pins and consider the internal oscillator calibration and configuration bits to match operating frequency. The device has adequate memory to run RTOS, USB stacks (with external PHY), or graphical LCD user interfaces. This page synthesizes distributor stock and pricing, drop-in pin-compatible alternatives within the PIC18 family, and practical design notes that complement the Microchip datasheet PDF.

Запрос цены Контакты

PIC18F252T-I/SO

PIC18F252T-I/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip

The Microchip Technology PIC18F252T-I/SO is a high-performance 8-bit CMOS FLASH microcontroller built on the PIC18 enhanced architecture, delivering 10 MIPS (100 ns instruction cycle) at 40 MHz, packaged in a 28-pin wide-body SOIC (SO) tape-and-reel configuration. It integrates 32 KB of program Flash, 1536 bytes of SRAM, 256 bytes of EEPROM, and a 10-bit multi-channel Analog-to-Digital Converter (ADC), alongside 23 digital I/O pins for mixed-signal embedded designs. What is a PIC18F 8-bit microcontroller? An 8-bit MCU executes instructions on 8-bit data paths at modest clock rates (typically 10–40 MIPS) and is widely used in cost-sensitive embedded control. The PIC18F family is Microchip's enhanced PIC architecture, upwards-compatible with the PIC16C5X, PIC12CXXX, and PIC16CXX lines, and adds a C-compiler-friendly instruction set, hardware multiply, and extended peripherals while remaining RISC-based. Within Microchip's taxonomy it sits under PIC microcontroller -> 8-bit MCU -> microcontroller (MCU) -> embedded processor -> semiconductor. The PIC18F252 specifically targets mid-range applications needing A/D conversion, PWM, and serial communication without moving to a 16-bit dsPIC or 32-bit ARM Cortex part. Key features include 32 KB (16K × 16) self-programmable Flash for in-application firmware updates, 256 bytes of EEPROM for non-volatile parameter storage, 5 channels of 10-bit ADC for sensor acquisition, a USART, MSSP (configurable as 3-wire SPI or I²C), 2 capture/compare/PWM modules for motor and lighting control, and 2 analog comparators. The wide 4.2 V–5.5 V supply range and industrial-grade -40 °C to +85 °C operating temperature suit factory-floor and automotive under-hood designs. Architecturally, the device uses Harvard-style separate program and data buses, an 8-bit data path, a 16-bit instruction word, and CMOS FLASH technology to deliver strong code density and low dynamic power. The enhanced core adds 77 single-word instructions, hardware multiply, and a software-stack model that simplifies C compiler code generation versus legacy PIC16 designs. Typical applications include industrial sensor conditioning, motor control with PWM-driven bridges, HVAC thermostat logic, automotive body controllers (under-hood temperature derated), USB-to-UART bridges when paired with a separate PHY, and consumer appliances requiring user-interface key-scans. The PIC18F252T-I/SO fits wherever deterministic 8-bit control, on-chip EEPROM, and modest analog integration are needed. When designing with this MCU, choose a 4 MHz–40 MHz crystal or resonator for the primary oscillator, populate the ICSP ICD pins for in-circuit debug, and route AVSS/VDD pairs to a quiet analog ground for best ADC accuracy. Always check the latest Microchip PIC18F252 errata and DS39576 family documentation before locking production firmware. This page consolidates verified distributor pricing, identical-footprint drop-in alternates, and engineering notes that go beyond the bare datasheet, helping procurement and design engineers evaluate the PIC18F252T-I/SO in a single view.

Запрос цены Контакты

PIC18F2539-E/SO

PIC18F2539-E/SO - 24KB Flash 8-bit MCU Motor Control | Microchip

The Microchip Technology PIC18F2539-E/SO is an 8-bit PIC18 RISC microcontroller featuring 24KB Flash program memory, 1408 bytes of RAM, and 256 bytes of EEPROM, housed in a 28-pin SOIC wide-body package. It integrates a sophisticated motor control kernel targeted at single-phase induction motor applications, with on-chip peripherals including two PWM modules, five channels of 10-bit Analog-to-Digital conversion, an ICD (In-Circuit Debugger) interface, and self-programming capability. The part operates from a 4.2V to 5.5V supply and supports a 40MHz internal clock architecture. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program and data memory, and peripheral interfaces on a single silicon die. Within the broader taxonomy, the PIC18F2539 sits at the microcontrollers -> integrated circuits -> semiconductors hierarchy. The PIC18 architecture in particular is a family of 8-bit RISC microcontrollers from Microchip Technology optimized for C-compiler-friendly development and deterministic interrupt handling. The PIC18F2539 belongs to the PIC18FXX39 sub-family that adds dedicated motor-control peripherals to the standard PIC18 feature set. Key features of this device include an enhanced 16-bit PWM with dedicated time-base and dead-band control, a 10-bit ADC with up to 5 input channels and programmable acquisition time, and a master synchronous serial port supporting both SPI and I2C master/slave modes. The instruction set is optimized for compiled C code, and the device supports self-programming for in-field firmware updates. An extended temperature grade option ("E" suffix) is qualified for -40C to +125C operation, making the part suitable for industrial and appliance-grade environments. Typical applications include single-phase induction motor control in washing machines, fans, pumps, and small appliances, where the integrated motor-control kernel eliminates discrete analog/digital conversion stages. Secondary uses include industrial sensor interface boards and HVAC damper/valve controllers, where the 24KB Flash and 1408-byte RAM are sufficient for control-loop firmware plus a small RTOS. The 28-pin SOIC package is widely used in through-hole-reflow-compatible designs and supports standard pick-and-place assembly. Designers should note that the -E temperature grade variant carries different cost and qualification status than the standard -I (industrial) variant, so confirm the order code matches your application's environmental requirements. For drop-in alternatives and second-source strategies, see the comparison table below; PIC18F2431 and PIC18F2539-I variants share the same 28-pin SOIC footprint but differ in Flash size or temperature grade.

Запрос цены Контакты

PIC18F2539-E/SP

PIC18F2539-E/SP - 8-bit 40MHz 24KB Flash MCU | Microchip

The Microchip PIC18F2539-E/SP is an 8-bit PIC18 family microcontroller featuring 24KB of Flash program memory, 1408 bytes of RAM, and 256 bytes of EEPROM, housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. The device runs at 40 MHz (10 MIPS) and operates from a 4.2V to 5.5V supply, integrating 25 I/O pins, two PWM modules, and a 5-channel 10-bit ADC. The extended (E) temperature grade spans -40C to +125C. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a single-chip computer that processes data in 8-bit chunks and integrates a CPU, non-volatile program memory (Flash/ROM), volatile data memory (RAM), peripherals, and I/O on one die. The PIC18 family sits within Microchip's broader PIC microcontroller taxonomy: PIC10/12/16/18 (8-bit) -> PIC24/dsPIC33 (16-bit) -> PIC32MX (32-bit MIPS) -> PIC32MM/MZ (32-bit ARM Cortex-M) -> microcontrollers -> embedded computing -> semiconductors. Within the PIC18 hierarchy, the PIC18F2539 belongs to the motor-control sub-family. Key differentiating features include a sophisticated single-phase induction motor control kernel (Power Control PWM with edge-aligned/center-aligned modes), an ICD (In-Circuit Debugger) interface for hardware debugging, self-programming Flash, and 21 digital I/O lines shared with analog inputs. The PIC18F2539 combines an enhanced 8-bit RISC core with motor-optimized peripherals, eliminating external driver logic for many single-phase BLDC and induction motor applications. Architecturally, the PIC18F2539 uses Microchip's enhanced Harvard architecture with separate program and data buses, a 32-level hardware stack, and a configurable oscillator block (8 MHz / 4x PLL to 40 MHz). The 10-bit ADC provides 5 channels with auto-acquisition and selectable conversion clock, while the two PWM channels deliver programmable duty, period, and dead-band control tailored for motor drive switching waveforms. Typical applications include single-phase induction motor control, ceiling fans, washing-machine pump drives, small HVAC blowers, and appliance variable-frequency drives. It also fits industrial relay replacement, sensor signal conditioning with on-chip ADC, and low-cost general-purpose 8-bit embedded control where through-hole SPDIP eases prototyping and field rework. Design consideration: budget for a 1-3 ms Power-on Reset and oscillator stabilization delay; use the configuration bits to select HS or INTOSC mode and to enable ICD. For motor-drive PCB layouts, keep the H-bridge traces short, place 0.1 uF + 10 uF decoupling at VDD/VSS, and isolate the analog AVSS/AVDD pair. This page synthesizes drop-in same-package alternatives, parameter-by-parameter comparison, and practical motor-control design notes beyond the data found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC18F2539-I/SP

PIC18F2539-I/SP - 40MHz 8-bit MCU 24KB Flash Motor Control | Microchip

The Microchip Technology PIC18F2539-I/SP is an 8-bit PIC18-family RISC microcontroller running at 40 MHz with 24 KB (12K x 16) of on-chip FLASH program memory and 1408 bytes of RAM, housed in a 28-pin SPDIP (SP) through-hole package. The device integrates a sophisticated single-phase induction motor control kernel (Power Control PWM) along with a 10-bit ADC and Capture/Compare/PWM (CCP/ECCP) peripherals targeted at appliance and white-goods motor drive designs. It is specified for the industrial -40C to +85C operating range and operates from 2.0 V to 5.5 V VDD. An 8-bit microcontroller (MCU) is a programmable processor built around an 8-bit data path, instruction-fetch architecture, on-chip non-volatile program memory, RAM, and mixed analog/digital peripherals. Within the broader semiconductor hierarchy, an MCU sits below microprocessors (which usually need external memory and peripherals) and above purely digital logic ICs; it is the workhorse of embedded control. The PIC18F family in particular targets applications requiring deterministic interrupt latency and on-board motor-control hardware rather than raw CPU throughput, and is classified as a microcontrollers -> Integrated Circuits category device. Key features include 21 digital I/O pins arranged across multiple ports, three 16-bit timers plus the motor-control PWMs, an enhanced CCP module for full-bridge or half-bridge drive, a 10-bit multi-channel A/D converter, USART with LIN support, an I2C/SPI MSSP peripheral, and an internal 8 MHz oscillator with PLL options. Programmable BOR and LVD enhance robustness in electrically noisy motor environments, while the ICD/ICSP debug interface accelerates firmware bring-up using Microchip's MPLAB X IDE and MPLAB XC8 toolchain. Architecturally the part uses a Harvard-style 16-bit instruction / 8-bit data path with a hardware multiplier and a hardware stack that supports C-compiler generated code, while the motor-control PWM block provides complementary outputs with programmable dead-band, fault inputs, and trigger-to-ADC synchronization that simplifies current-sense timing. The integrated single-phase induction motor control kernel allows field-oriented style control in software without external DSP hardware. Typical applications include single-phase induction motor control (washing machines, pumps, fans), appliance control boards, HVAC blowers, compact low-cost variable-frequency drives, and general-purpose 5 V/3.3 V embedded control with on-board ADC and PWM. The SPDIP-28 package suits through-hole designs and prototyping where easy rework is preferred over SMT density. Design consideration: choose this device when you need integrated single-phase induction motor firmware primitives and an SPDIP footprint; for SMT-only designs evaluate the SOIC-28 (-I/SO) variant or a QFN-packaged PIC18F motor-control part. Adequate decoupling (100 nF + bulk) and a stable LDO feeding AVDD are required for accurate ADC readings. This page consolidates distributor pricing, drop-in PIC18F-family alternatives in the same SPDIP-28 footprint, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

PIC18F2539T-E/SO

PIC18F2539T-E/SO - 8-bit 40MHz MCU, 24KB Flash, 28-SOIC | Microchip

The Microchip Technology PIC18F2539T-E/SO is an 8-bit RISC microcontroller from the PIC18F family, offered in a 28-pin SOIC package with extended operating temperature range and tape-and-reel packaging (T suffix). It features 24KB of Flash program memory, 1408 bytes of RAM, 21 I/O pins, and a maximum clock speed of 40 MHz at 5V operation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral interfaces onto one die. The PIC18F family uses an enhanced Harvard RISC architecture with 16-bit instructions and 8-bit data paths, and the PIC18F2539 specifically merges this architecture with a sophisticated motor control kernel. This kernel targets single-phase induction motor control applications, providing dedicated PWM, capture/compare, and quadrature encoder interfaces on-chip. As a member of the 8-bit MCU hierarchy, the PIC18F2539 sits between simpler PIC16F devices and the higher-end PIC24/dsPIC families. Key features include a 10-bit ADC module (motor-control-tuned), enhanced USART, MSSP (SPI/I2C), and a 16-bit motion feedback module. The device operates from 4.2V to 5.5V with an extended industrial temperature range (-40C to +125C), suitable for harsh environments. With on-chip Flash and In-Circuit Serial Programming (ICSP), firmware updates can be performed in the field without removing the part. Typical applications include single-phase induction motor drives, fan and pump controllers, white-goods motor boards, and HVAC damper control. The integrated motion control peripherals reduce external component count for sensorless or closed-loop BLDC/induction drive implementations. When designing with this device, ensure decoupling capacitors are placed close to VDD/VSS pins and that the MCLR pull-up is correctly biased. The PIC18F2539 family shares its datasheet with PIC18F2439/4439/4539 variants for engineers migrating between pin counts. This page synthesizes distributor pricing, same-package alternatives (28-SOIC), and practical design notes not found in the manufacturer datasheet summary.

Запрос цены Контакты

Подкатегории

Товары (35.000+)

PIC18F252-E/SP - 8-Bit MCU, 32KB Flash, 40MHz, SPDIP-28 | Microchip

PIC18F252-I/SO - 8-bit 40MHz 32KB Flash MCU | Microchip | 28-SOIC

PIC18F2520-E/SO - 8-bit 25MHz 32KB Flash MCU 28-SOIC | Microchip

PIC18F2520-E/SP - 8-bit MCU, 32KB Flash, 28-SPDIP | Microchip

PIC18F2520-I/ML - 8-Bit 40MHz 32KB Flash MCU 28-QFN | Microchip

PIC18F2520-I/SO - 8-bit MCU, 32KB Flash, 40MHz, 28-SOIC | Microchip

PIC18F2520-I/SP - 8-bit 40MHz 32KB Flash MCU | Microchip | 28-SPDIP

PIC18F2520T-I/ML - 8-bit MCU, 32KB Flash, 40MHz, 28-QFN | Microchip

PIC18F2520T-I/SO - 8-bit 40MHz 32KB Flash MCU | Microchip

PIC18F2523-E/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip

PIC18F2523-E/SP - 8-Bit MCU 32KB Flash 40MHz 28-SPDIP | Microchip

PIC18F2523-I/ML - 8-Bit MCU, 32KB Flash, 12-bit ADC, 28-QFN | Microchip

PIC18F2523-I/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip

PIC18F2523-I/SP - 8-bit 32KB Flash MCU, 28-SPDIP | Microchip

PIC18F2523T-I/ML - 32KB Flash, 8-bit MCU, 28-QFN | Microchip

PIC18F2525-E/SO - 48KB Flash 8-bit MCU, 25 I/O | Microchip

PIC18F2525-E/SP - 48KB Flash, 25MHz 8-bit MCU, SPDIP-28 | Microchip

PIC18F2525-I/SO - 8-Bit 40MHz MCU 48KB Flash 28-SOIC | Microchip

PIC18F2525-I/SP - 8-Bit PIC MCU, 48KB Flash, 40MHz | Microchip

PIC18F252T-I/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip

PIC18F2539-E/SO - 24KB Flash 8-bit MCU Motor Control | Microchip

PIC18F2539-E/SP - 8-bit 40MHz 24KB Flash MCU | Microchip

PIC18F2539-I/SP - 40MHz 8-bit MCU 24KB Flash Motor Control | Microchip

PIC18F2539T-E/SO - 8-bit 40MHz MCU, 24KB Flash, 28-SOIC | Microchip