Интегральные схемы

S9S08DN32F1VLC

S9S08DN32F1VLC - 8-bit S08 MCU, 32KB Flash, LQFP-32 | NXP

The NXP Semiconductors S9S08DN32F1VLC is an 8-bit HCS08 microcontroller with a 40 MHz HCS08 CPU (20 MHz internal bus), 33 KB flash memory, and 3.3V/5V operation, housed in a 32-pin LQFP (7x7 mm) package qualified to AEC-Q100 for automotive applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a processor core, program flash, RAM, and peripherals such as timers, ADCs, and communication interfaces on one die. Within the power-management hierarchy of embedded systems, the MCU sits at the application-control layer, reading sensors and driving actuators. The HCS08 family is NXP's (formerly Freescale) enhanced successor to the HC08, adding the BGND background-debug instruction and up to 32 interrupt/reset sources. Key features of the S9S08DN32 include the 40 MHz HCS08 core with full HC08 instruction-set compatibility for easy code migration, 33 KB of on-chip flash for program storage, and support for both 3.3V and 5V supply rails, which simplifies integration into mixed-voltage automotive and industrial boards. The related S08DV family devices in the same core offer a 24-channel, 12-bit ADC with 2.5 us conversion time for analog sensing tasks. Technically, the enhanced HCS08 core uses a CISC architecture with a von Neumann memory map, and background debugging (BGND) enables non-intrusive flash programming and real-time emulation through a single-wire interface. The AEC-Q100 qualification and 'V' temperature grade make the part suitable for under-hood and body-electronics environments. Typical applications include automotive body controllers, LIN-based actuator nodes, HVAC flap and blower control, sensor hubs, and industrial motor or power-supply supervision where a low-cost 8-bit core with automotive qualification is required. For design, confirm the exact flash/RAM and peripheral configuration in the manufacturer datasheet for the DN32 derivative before finalizing the memory map, as the S08D family shares documentation across multiple derivatives. This page synthesizes distributor listings, family cross-references, and drop-in alternative analysis not found in the manufacturer datasheet.

USD $1,30 В наличии

S9S08DN32F2VLC

S9S08DN32F2VLC - 8-bit S08 MCU 32KB Flash 40MHz LQFP-32 | NXP

The NXP S9S08DN32F2VLC is an 8-bit microcontroller based on the S08 CISC core running at up to 40 MHz, with 32KB (32K x 8) flash memory, 1KB RAM, and dual on-chip analog comparators, housed in a 32-pin LQFP (7x7 mm) package qualified for automotive applications and rated from -40C to +105C. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a processor core, program flash, RAM, and peripherals such as timers, serial interfaces, and analog blocks on one die. Within the semiconductor hierarchy, it sits under the microcontroller family of embedded processors, which itself belongs to the broader category of integrated circuits and system-on-chip devices. The NXP S08 family descends from the classic Freescale HC08 lineage, retaining CISC instruction-set compatibility while adding modern flash memory and debug features. Key features of the S9S08DN32 include the 40 MHz S08 core, 32KB in-system-programmable flash, embedded CAN support within the DN family architecture, dual analog comparators suited to motor-control feedback, and on-chip background debug/emulation that removes the need for external emulation hardware. The automotive qualification (the S9 prefix denotes the automotive grade of the MC9S08DN32) and the wide -40C to +105C operating range make it suitable for harsh environments. Architecturally, the device pairs the 8-bit S08 CISC core with flash and RAM organized for real-time control loops. The dual comparators allow direct interfacing with current-shunt or back-EMF signals in brushless DC and stepper motor drives, while timer and communication peripherals handle PWM generation and network connectivity. Supply operation covers both 3.3V and 5V systems per distributor data. Typical applications include automotive body and powertrain adjunct modules, industrial motor control, sensor nodes, and generic embedded control where a small, robust 8-bit controller is required. The 32-pin LQFP footprint suits compact two-layer and four-layer boards. A key design consideration: distributor listings flag this part as a mask-only automotive device, so verify long-term supply and consider flash-based family variants for new designs. This page synthesizes distributor listings, cross-reference findings, and drop-in alternative analysis not found on any single manufacturer or distributor page.

Запрос цены В наличии

S9S08DV128F2CLFR

S9S08DV128F2CLFR - 8-Bit 40MHz 128KB MCU | NXP

The NXP Semiconductors S9S08DV128F2CLFR is an 8-bit S08 microcontroller with a 40 MHz maximum clock, 128 KB of embedded Flash, and a 48-lead LQFP package measuring 7 mm by 7 mm. It is designed for automotive-qualified embedded control applications operating across the -40 °C to +85 °C temperature range. The device combines a compact general-purpose microcontroller footprint with substantial on-chip program memory for control-oriented firmware. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, and peripherals into one embedded-control component. The S08 family belongs to the broader 8-bit MCU hierarchy and is commonly used when deterministic control, modest processing demand, and a compact embedded platform are more important than high-end computation. The S9S08DV128F2CLFR is therefore suited to motor, body, sensor, and industrial-control subsystems. The verified product information identifies an S08 core, 8-bit architecture, 128 KB Flash organized as 128K x 8, and a maximum frequency of 40 MHz. Its automotive qualification is useful for applications requiring a documented automotive-grade temperature range, while the 48-LQFP package provides a leaded surface-mount form factor for PCB assembly. The R suffix and package suffix identify ordering and package-related ordering details; exact suffix interpretation should be confirmed against the NXP ordering information. Typical implementation roles include automotive body-control modules, actuator controllers, sensor-hub controllers, and small motor-control platforms. The 40 MHz clock provides processing headroom for interrupt-driven control, while 128 KB Flash provides room for application firmware, configuration tables, and diagnostic routines. Exact RAM size, peripheral configuration, electrical limits, pin names, and package dimensions beyond the verified package size are not supplied in the retrieved data. PCB design should preserve the LQFP land pattern, route power and ground carefully, and validate signal integrity for any externally connected interface. Because the verified excerpts do not provide a complete manufacturer pinout, a complete pin map should be downloaded from the official NXP datasheet before layout or firmware bring-up. Automotive production designs should additionally follow the manufacturer’s qualification, traceability, and validation requirements. This page combines the verified distributor specifications, package identity, sourcing links, and application guidance for S9S08DV128F2CLFR. It emphasizes the information needed for initial component selection while clearly separating confirmed facts from parameters that still require datasheet confirmation.

USD $6,28 В наличии

S9S08DV16F2MLC

S9S08DV16F2MLC - 8-bit S08 MCU 16KB Flash 40MHz | NXP

The NXP Semiconductors S9S08DV16F2MLC is an automotive-qualified 8-bit microcontroller built on the S08 (HCS08) CISC core, running at up to 40 MHz with 16 KB of flash memory, 2 KB of RAM, and a 12-bit ADC, housed in a 32-pin LQFP (7x7 mm) package rated from -40C to +125C under AEC-Q100. An 8-bit microcontroller is an integrated circuit that combines a processor core, program memory, data memory, and peripherals on a single chip, executing one instruction on 8-bit data words per cycle. Within the system hierarchy, the S08 family sits under NXP's broader MCU portfolio (8-bit MCU -> microcontroller unit -> embedded processor), positioned for cost-sensitive embedded control where CAN networking, embedded EEPROM, and on-chip debug are valued over raw compute power. Key features of the S9S08DV16F2MLC include the 40 MHz S08 core delivering efficient CISC execution, 16 KB (16K x 8) of in-system-programmable flash for code storage, 2 KB of RAM for runtime data, and a 12-bit analog-to-digital converter suited to sensor interfacing. The supply range of 2.7 V to 5.5 V allows direct operation from 3.3 V or 5 V rails, simplifying mixed-voltage system design. According to NXP product information, this family was developed as an 8-bit MCU family with embedded CAN, embedded EEPROM, and on-chip emulation/debug targeted specifically at the automotive and industrial markets. The S08 architecture provides background debug mode (BDM) via single-wire on-chip emulation, eliminating the need for external debug silicon in many cost-optimized designs. Flash endurance and embedded EEPROM emulation support parameter storage without an external non-volatile device. The 32-LQFP 7x7 mm surface-mount package offers a practical pin count for gateway nodes, sensor modules, and actuator drivers on a CAN bus. Typical applications include automotive body electronics such as door modules, seat control, and lighting control; industrial nodes on CAN networks; and motor or solenoid control loops that exploit the 12-bit ADC and timer resources. The -40C to +125C operating range makes it directly suitable for under-hood and near-engine locations. A key design consideration: verify flash and RAM headroom early, since 16 KB flash and 2 KB RAM bound firmware size; larger siblings in the same family (32 KB, 48 KB) share the package footprint for later upgrades. Pricing starts around $3.16 at authorized distributors (as of 2026-10-18). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $2,10 В наличии

S9S08DV32F1MLC

S9S08DV32F1MLC - 8-bit HCS08 MCU 32KB Flash 40MHz | NXP

The NXP S9S08DV32F1MLC is an 8-bit HCS08 family microcontroller IC delivering 40 MHz CPU performance with 32 KB Flash, 2 KB RAM, and 25 I/O pins in a 32-pin LQFP (7x7) surface-mount package, designed for 3.3 V / 5 V automotive-grade embedded systems. What is an 8-bit microcontroller? An 8-bit MCU (microcontroller unit) is a small self-contained computing device that integrates a CPU, Flash program memory, RAM, peripherals (ADC, timers, communication blocks), and I/O on a single die. It sits in the broader category of microcontrollers within integrated circuits and embedded computing. The HCS08 is the enhanced 8-bit core family that succeeded the legacy HC08 instruction set, adding the BGND instruction for background-debug support while preserving the original CISC instruction set for code compatibility. Key features include a 40 MHz HCS08 CPU core with 20 MHz bus, 32 KB (32K x 8) Flash program memory, 2 KB (2K x 8) RAM, and a 12-bit resolution ADC with up to 16 / 24 channels and 2.5 microsecond conversion time. It supports up to 32 interrupt/reset sources, runs from a 3.3 V / 5 V supply, and uses an external oscillator. The 32-LQFP (7x7 mm) package is qualified for automotive environments. Architecturally, the S9S08DV32F1MLC combines the HCS08 CISC core with on-chip debug, integrated timer/PWM/ADC modules, and the automotive-grade temperature and quality flows required by NXP's S08DV sub-family. Its 40 MHz operation and 2.5 us ADC conversion enable real-time control loops in engine, body, and chassis subsystems. Typical applications include automotive body controllers, HVAC control modules, instrument clusters, sensor interface boards, and industrial CAN-enabled supervisory nodes. The 32 KB Flash / 2 KB RAM balance is well suited to small protocol stacks such as LIN slave and CAN nodes. Design consideration: confirm oscillator selection supports the 40 MHz CPU clock, provide adequate decoupling on AVDD/VDD, and verify the supply range against the 3.3 V / 5 V rating. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and design notes not present on NXP's bare product page.

USD $2,74 В наличии

S9S08DV96F2CLL

S9S08DV96F2CLL - 40MHz 96KB Flash 8-Bit MCU | NXP

The NXP Semiconductors S9S08DV96F2CLL is an 8-bit S08 microcontroller with 96KB flash memory, a 40MHz processor core, dual-voltage operation, a built-in debug module, and a 100-lead LQFP package. It is identified in distributor data as an automotive-qualified part operating from -40°C to +85°C, making it suitable for embedded control applications requiring broad temperature coverage and integrated development support. A microcontroller is a programmable semiconductor that combines a processor core, memory, peripherals, and interfaces on one integrated circuit. This MCU belongs to the HCS08 family of 8-bit devices, where the S08 core executes embedded control logic and communicates with sensors, actuators, communication transceivers, and human-machine interfaces. Its 96KB flash provides nonvolatile program storage, while the integrated debug module supports development and troubleshooting. The S9S08DV96F2CLL is specified in the supplied data as an automotive-qualified S08 MCU with a 40MHz clock and 100-LQFP package. The exact memory-map details, peripheral configuration, supply-voltage limits, GPIO count, CAN characteristics, and environmental ratings beyond the provided operating-temperature statement were not available in the verified data and are therefore not inferred here. The device should be selected only after checking the manufacturer datasheet for the exact package pinout, electrical limits, and peripheral assignments. Its 8-bit architecture is appropriate for cost-sensitive embedded systems where moderate processing throughput is sufficient and deterministic control is more important than high-end computation. The 40MHz rating supports the device family’s embedded-control positioning, while 96KB flash offers substantially more program space than very small 8-bit controllers. The LQFP-100 package also exposes a comparatively large number of external connections for systems needing multiple I/O or communication resources. Typical applications include automotive body and accessory controllers, CAN-based node modules, instrumentation, industrial automation, motor-control peripherals, and embedded gateway systems. A design should include appropriate decoupling, clock and reset consideration, peripheral-level protection, and validation against the specific automotive or industrial requirements of the finished product. This page synthesizes verified manufacturer and distributor information, identifies unavailable technical fields explicitly, and provides practical selection guidance without inventing pricing, pin assignments, or standards compliance claims.

Запрос цены В наличии

S9S08DV96F2VLL

S9S08DV96F2VLL - 40MHz 96KB Automotive 8-Bit MCU | NXP

NXP Semiconductors S9S08DV96F2VLL is an automotive-qualified 8-bit S08 microcontroller with 96KB flash, a 40MHz HCS08 core, and a 100-LQFP 14x14 mm package. It operates from 3.3V/5V supply rails and is specified for -40°C to +105°C ambient conditions. The device also includes embedded CAN, embedded EEPROM, and on-chip emulation and debugging support for automotive and industrial control systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals on one chip. The S9S08DV96F2VLL belongs to the HCS08 family and is positioned as an 8-bit embedded controller rather than a general-purpose computing processor. Its combination of flash program memory, serial communication, embedded debugging, and extended temperature qualification supports applications that require deterministic control and field evaluation. The verified device data identifies a 40MHz CPU with a 20MHz bus, 96K x 8 flash, support for up to 32 interrupt or reset sources, and embedded CAN communication. The 100-LQFP package provides 100 external leads and is suitable for larger automotive and industrial boards where lead spacing and inspection requirements favor through-hole-style gull-wing packaging over a fine-pitch QFN. The MCU is marked automotive qualified, and one verified source associates the device with AEC-Q100. Its -40°C to +105°C rating is appropriate for demanding industrial and automotive environments, although the exact electrical limits and timing values should be confirmed in the manufacturer datasheet before design release. The device also appears in distributor listings as both Freescale Semiconductor and NXP USA Inc., reflecting its product-line history rather than a change in the MPN. Typical uses include automotive body or powertrain-adjacent control modules, CAN-connected industrial controllers, instrumentation, embedded motor-control logic, and 3.3V/5V systems requiring on-chip debug. For design work, preserve the S08 programming model, verify the 100-pin land pattern, connect the required oscillator and reset circuitry, and confirm the exact transceiver, connector, and protection components for the system voltage. The most important design trade-off is package and qualification rather than core performance. A 100-LQFP footprint is larger than a modern low-pin-count MCU package, but it offers ample external I/O and straightforward assembly. Validate startup behavior, watchdog usage, CAN timing, and thermal exposure against the complete manufacturer documentation before production use.

Запрос цены В наличии

S9S08DZ16F1MLC

S9S08DZ16F1MLC - 16KB Flash 40MHz HCS08 MCU 32-LQFP | NXP

The NXP Semiconductors / Freescale S9S08DZ16F1MLC is a 40 MHz HCS08-family 8-bit microcontroller with 16 KB (16K x 8) on-chip Flash program memory and 1 KB (1K x 8) RAM, housed in a 32-pin LQFP (7x7 mm) package. The device integrates a 24-channel 12-bit ADC with 2.5 us conversion time, plus CAN, I2C, LIN, SCI, and SPI serial interfaces, and provides 25 general-purpose I/O lines operating from a 2.7 V to 5.5 V supply. An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and programmable peripheral interfaces. In the system hierarchy, MCUs sit between discrete logic ICs and full microprocessors: they replace multi-chip glue logic by embedding the processor, memory, and analog/digital peripherals on one die. The S08 family uses Freescale's enhanced HCS08 core, which adds the BGND instruction to the legacy HC08 instruction set while remaining object-code compatible, easing migration from older HC08 designs. Key features of the S9S08DZ16F1MLC include a 40 MHz CPU with a 20 MHz bus, support for up to 32 interrupt and reset sources, an external oscillator interface, and operation from -40 C to +125 C (industrial/automotive ambient). The integrated 12-bit ADC and CAN interface make the part attractive for sensor-rich node designs, while the SCI/SPI/I2C set covers most low-speed peripheral connections without external glue logic. The architecture is a Harvard-style design with separate Flash and RAM buses, allowing instruction fetch and data access to overlap. The HCS08 core implements a 16-bit stack pointer, indexed addressing with H:X, and a single BGND opcode for background-debug entry used by BDM (Background Debug Mode) probes such as NXP's USBMULTILINK. Typical applications include automotive body controllers (CAN/LIN nodes), industrial sensor hubs (24-channel ADC fan-in), HVAC control panels, small appliance motor controllers, and low-pin-count embedded control boards. The wide supply range (2.7 V to 5.5 V) simplifies designs that must accept both 3.3 V and 5 V rails. When designing with this MCU, budget Flash and RAM for the largest expected application footprint (16 KB / 1 KB), allocate one timer channel for the system tick, and reserve at least two I/O pins for the BDM debug interface to avoid losing in-system programming access. This page synthesizes distributor pricing, same-family drop-in alternatives (S9S08DZ16F2MLC, S9S08DZ60F2MLC), and design notes not found in the manufacturer datasheet alone.

USD $3,65 В наличии

S9S08DZ16F1MLF

S9S08DZ16F1MLF - 8-bit 40MHz HCS08 MCU, 16KB Flash, 48-LQFP | NXP

The NXP S9S08DZ16F1MLF is an 8-bit HCS08-family microcontroller with 16KB of on-chip Flash program memory and 1KB of RAM, housed in a 48-pin LQFP (7x7 mm) package and qualified to automotive temperature grade. It integrates a 40-MHz HCS08 CPU (20-MHz bus), a 24-channel 12-bit ADC with 2.5 microsecond conversion time, an external oscillator interface, and up to 39 general-purpose I/O pins. An 8-bit microcontroller (MCU) is a single-chip processor that integrates a CPU, non-volatile program memory (Flash), working RAM, peripherals, and interrupt logic into one package. The HCS08 architecture is NXP's enhanced 8-bit core that builds on the legacy HC08 instruction set with added BGND (background debug) support and up to 32 interrupt/reset sources. As a member of the broader MCU family tree, the HCS08 sits within 8-bit microcontrollers, which sit within microcontrollers, which sit within embedded microprocessors, which sit within the Integrated Circuits (ICs) hierarchy used in power management, sensing, and motor control subsystems. Key features include 16KB Flash / 1KB RAM, 40-MHz CPU core, 24-channel 12-bit ADC with 2.5 microsecond conversion time, MSCAN (Controller Area Network) interface for automotive networking, and an integrated SCI/SPI/IIC peripheral set. The 48-LQFP package offers a low-pin-count entry point with 39 usable I/O lines, while automotive temperature grade and a mask-set suffix (M74K MASK ONLY-AUTO) identify it as a factory-locked, customer-specific configuration. The architecture centers on the HCS08 core running up to 20-MHz bus frequency, a 24-channel ADC supporting simultaneous automotive sensor sampling, and CAN/SCI/SPI/IIC communication blocks suited for body-electronics and body-control-module (BCM) networks. The mask-only designation means firmware is pre-programmed by NXP to customer code - this part is not user-programmable in the field, but is delivered with locked Flash content. Typical applications include automotive body electronics, instrument clusters, lighting controllers, HVAC modules, and low-end CAN nodes where the integrated MSCAN peripheral reduces external component count. The 40-MHz core also supports small sensor-hub designs that require deterministic interrupt response. When designing with this MCU, ensure the CAN bus transceiver (e.g. TJA1050) is AC-coupled and that the ADC reference pin is decoupled with a low-ESR capacitor. The mask-only nature means field firmware updates are not possible; supply-chain and code-revision control must be enforced at the OEM level. This page synthesizes distributor pricing, drop-in same-package alternatives, and design notes not found in the manufacturer datasheet alone.

USD $3,67 В наличии

S9S08DZ16F2MLC

S9S08DZ16F2MLC - 40MHz 16KB Flash MCU | NXP | Automotive

The NXP Semiconductors S9S08DZ16F2MLC is an 8-bit S08 automotive-qualified microcontroller with 40 MHz maximum clock frequency, 16 KB of Flash program memory, and a 32-pin LQFP package. It is designed for embedded automotive and industrial systems requiring deterministic control, mixed-signal measurement, and serial connectivity. Verified listings also identify CAN bus, I2C, LIN bus, SCI, SPI, an 8-bit ADC, low-voltage detection, power-on reset, PWM, watchdog, and 25 I/O pins. A microcontroller is a programmable system-on-chip that executes firmware, reads inputs, controls outputs, and manages communication protocols. The S08 belongs to the 8-bit MCU -> embedded controller -> semiconductor hierarchy. Compared with more complex application processors, this device emphasizes compact code execution, real-time peripherals, and low-pin-count integration. Its automotive qualification makes it relevant to body, chassis, comfort, and industrial controller designs where operating-temperature robustness and interface breadth matter. Verified source snippets identify a -40°C to +125°C operating range, 16 KB Flash, 4 KB RAM in the distributor overview, an 8-bit ADC, SCI, and SPI interfaces, plus CAN, I2C, LIN, PWM, watchdog, LVD, and POR functions. The 32-LQFP package measures 7 mm by 7 mm according to distributor data. These details support compact controller layouts with external sensing, communications, and actuator interfaces. The part uses the NXP S08 8-bit core and supports embedded automotive communication environments. CAN and LIN connectivity are especially useful for distributed vehicle networks, while SCI and SPI allow connection to sensors, transceivers, displays, and external memory or digital peripherals. The ADC provides an analog measurement path where a dedicated external converter would otherwise be required. Typical uses include automotive body-control modules, sensor nodes, motor or actuator controllers, HVAC interfaces, lighting controllers, and industrial embedded-control boards. Because it is an 8-bit MCU with 16 KB Flash, firmware size and interrupt latency should be checked early; applications requiring extensive protocol stacks, graphics, or large data storage may need a higher-capacity MCU. For a new PCB, preserve the verified 32-pin LQFP footprint and validate the exact pin multiplexing, voltage domains, oscillator connections, and debug interface against the manufacturer datasheet. For an existing design, verify package pin compatibility, firmware dependencies, memory map, peripheral availability, and qualification requirements before approving any substitute. This page combines verified distributor specifications, availability references, and design-oriented selection guidance. It intentionally distinguishes confirmed data from missing parameters and does not infer unreported electrical limits, pin names, or unqualified drop-in replacements.

Запрос цены В наличии

S9S08DZ16F2MLF

S9S08DZ16F2MLF - 8-bit S08 MCU 16KB Flash CAN 40MHz | NXP

The NXP Semiconductors S9S08DZ16F2MLF is an automotive-qualified 8-bit microcontroller based on the S08 CISC core, running at up to 40 MHz bus speed with 16KB (16K x 8) of on-chip Flash memory, 512 bytes of EEPROM, and 2KB of RAM, housed in a 48-pin LQFP (7x7 mm) surface-mount package rated from -40C to +125C. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals such as timers, serial interfaces, and analog blocks. In the power-management hierarchy of embedded systems, MCUs of this class sit at the lowest cost tiers, typically controlling actuators, sensors, and communication links in automotive body electronics, motor control, and industrial nodes where a 32-bit processor would be unnecessary. Key features of the S9S08DZ16 family include an embedded CAN 2.0 A/B controller - one of the first such integrations in an 8-bit MCU family - along with I2C, LINbus, SCI, and SPI connectivity. Peripheral support includes low-voltage detection (LVD), power-on reset (POR), PWM timers, a watchdog timer (WDT), and on-chip emulation/debug, eliminating the need for external debug headers in cost-sensitive designs. The device operates from a 2.7V to 5.5V supply and retains data in Flash across power cycles while the 512-byte EEPROM provides parameter storage without external memory. The 40 MHz core clock combined with the CAN interface makes the part well suited to in-vehicle network nodes that must respond quickly to bus traffic. Typical applications include automotive body control modules, seat and mirror controllers, HVAC actuators, LIN/CAN gateway satellites, and industrial sensor nodes. The -40C to +125C operating range and automotive qualification make it appropriate for under-hood and in-cabin environments alike. Designers should budget the 39 available general-purpose I/O pins carefully when using the CAN, SPI, and I2C peripherals simultaneously, since pin multiplexing reduces available GPIO. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

USD $1,10 В наличии

S9S08DZ32F1MLF

S9S08DZ32F1MLF - 40MHz HCS08 MCU, 32KB Flash, 48-LQFP | NXP

The NXP Semiconductors S9S08DZ32F1MLF is a 40 MHz HCS08-family 8-bit microcontroller with 32 KB of embedded Flash and 2 KB of RAM, packaged in a 48-pin LQFP (7x7 mm). Built on the enhanced HCS08 core, it delivers up to 20 MHz bus speed while maintaining backward compatibility with the HC08 instruction set augmented by the BGND instruction. The part is targeted at automotive body and chassis applications where cost-effective CAN connectivity, robust Flash memory, and a wide peripheral mix are required. An 8-bit microcontroller (MCU) is a microprocessor core integrated with on-chip memory, peripherals, and interrupt logic on a single die. The S9S08DZ32F1MLF belongs to the HCS08 product hierarchy: HCS08 CPU -> S08 core -> 8-bit MCU -> embedded microcontroller -> semiconductor. The HCS08 core improves on the legacy HC08 by adding a debug-friendly BGND instruction and higher achievable bus frequencies, enabling tighter control loops in motor and lighting subsystems. Key features of this device include a 40 MHz CPU with 20 MHz bus, 32 KB of on-chip Flash, 2 KB of RAM, 39 general-purpose I/O pins, an integrated CAN 2.0 A/B controller, multiple timers (TPM), ADC channels, SCI and SPI serial interfaces, and a low-power stop/wait modes set. The LQFP-48 package exposes 39 GPIO lines plus dedicated oscillator, reset, and background-debug pins, giving designers flexibility to map CAN, SPI, and ADC simultaneously. Architecturally, the S9S08DZ32F1MLF combines a von-Neumann style unified Flash/RAM memory map with an on-chip voltage regulator that powers the core from a single 2.7 V-5.5 V external supply. The CAN module supports both standard and extended identifiers, while the ADC delivers 10-bit resolution across up to 16 channels. Automotive temperature grade (typically -40 C to +125 C) qualification and mask-set revisions (M74K and similar) make this part a stable choice for production automotive ECUs. Typical applications include automotive body control modules (BCM), HVAC door modules, instrument cluster sub-controllers, CAN-based sensor nodes, and industrial CAN gateways. Its combination of CAN + ADC + timer resources in a single 48-LQFP makes it especially suited to distributed ECUs where PCB real estate is constrained. Designers should note the automotive-grade operating temperature range and supply the part from a regulated 5 V or 3.3 V rail depending on the chosen flash erase/write algorithm. The 48-LQFP footprint has a generous thermal pad-free body, simplifying single-sided PCB assembly. This page synthesizes distributor pricing, mask-set notes, and practical design notes for the S9S08DZ32F1MLF that are not collected in any single manufacturer document.

USD $4,21 В наличии

S9S08DZ32F2VLCR

S9S08DZ32F2VLCR - 8-bit S08 MCU, 32KB Flash, CAN, 32-LQFP | NXP

The NXP Semiconductors S9S08DZ32F2VLCR is an 8-bit S08 CISC microcontroller with 32 KB of Flash, 40 MHz CPU clock, and automotive-grade qualification (-40C to +105C), housed in a 32-pin LQFP package. It is part of NXP's S08DZ family, the industry's first 8-bit MCU family to integrate CAN, embedded EEPROM, and on-chip emulation/debug for automotive and industrial markets. Key specifications include 32 KB program Flash, 2 KB RAM, an integrated LCD driver, and CAN 2.0 A/B controller. What is an 8-bit CISC microcontroller (MCU)? An 8-bit MCU is a single-chip computer with an 8-bit data path, optimized for cost-sensitive, deterministic, real-time control. CISC (Complex Instruction Set Computer) architectures provide a rich instruction set with variable-length opcodes that improve code density, reducing Flash pressure in embedded systems. Within the broader taxonomy, an 8-bit MCU belongs to the microcontroller family, sitting alongside 16-bit and 32-bit MCUs in the semiconductor hierarchy. The S08DZ specifically targets automotive and industrial segments requiring CAN networking, low power, and AEC-Q100-grade qualification. This part features an integrated CAN 2.0 A/B controller, on-chip EEPROM for non-volatile data storage without external serial memory, an LCD driver supporting segmented displays up to 8x32 segments, and an enhanced capture/timer/PWM module. The S08 CPU core delivers 40 MHz throughput with background debug mode (BDM) for non-intrusive in-circuit programming and debugging, reducing development-tool costs compared to boundary-scan solutions. Typical applications include automotive body control modules, instrument clusters, HVAC controls, industrial sensor nodes, and CAN-based distributed control networks. The integrated LCD driver eliminates external display controller cost in applications with segmented character or graphic displays. AEC-Q100 qualification and the -40C to +105C operating range support under-hood and cabin-mounted automotive electronics where commercial-grade MCUs cannot survive. When designing with this device, note that the LQFP-32 pin count limits I/O to ~26 usable GPIO pins after LCD, CAN, and oscillator allocations. The 5V-tolerant I/O simplifies interfacing to legacy 5V sensors and actuators in automotive subsystems. Use the BDM interface (background-debug pins BKGD/MS) for in-circuit programming and debugging, eliminating the need for an expensive in-circuit emulator. This page synthesizes distributor pricing, S08DZ-family drop-in alternatives, and practical design notes for CAN/LCD automotive applications not found in the manufacturer datasheet.

USD $4,20 В наличии

S9S08DZ48F1CLH

S9S08DZ48F1CLH - 8-bit MCU, 48KB Flash, CAN, 64-LQFP | NXP

The NXP (Freescale) S9S08DZ48F1CLH is an 8-bit microcontroller from the S08DZ family built on the enhanced HCS08 core, running at up to 40 MHz CPU / 20 MHz bus speed with 48KB of Flash program memory and 64KB addressable space, housed in a 64-pin LQFP (10x10 mm) surface-mount package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a processor core, program and data memory, and peripheral modules such as timers, serial interfaces, and analog-to-digital converters. Within the hierarchy of embedded processors, 8-bit MCUs such as the HCS08 family sit below 16-bit and 32-bit devices, offering low cost, low power, and simple single-supply designs for control-oriented tasks. The S08DZ family is NXP's first 8-bit MCU family with embedded CAN, embedded EEPROM, and on-chip emulation/debug, targeting automotive and industrial markets. Key features of the S9S08DZ48F1CLH include the 40 MHz HCS08 CPU with HC08 instruction set plus the added BGND instruction, support for up to 32 interrupt/reset sources, 48KB Flash with in-application reprogramming, 3KB RAM, and embedded EEPROM for parameter storage. The integrated CAN (FlexCAN-type) module is the family's defining differentiator, enabling direct connection to vehicle networks and industrial field buses without an external CAN controller. Technically, the device uses the enhanced HCS08 core with a background debug mode (BGND) that supports non-intrusive on-chip debugging and flash programming through a single-wire interface, reducing development cost by eliminating the need for expensive socketed emulators. Scalability across the S08D family - with pin, peripheral, and software-compatible members at 16KB, 32KB, 48KB, and 60KB - allows firmware migration as memory requirements grow. Typical applications include body control modules, gateways, seat and mirror controllers, HVAC actuators in automotive systems, and motor control, lighting, and sensor-node designs in industrial equipment where Controller Area Network connectivity is required. Designers should budget the Flash endurance and EEPROM wear levels against their parameter-logging rate, and use the on-chip debug interface during development to avoid reserving pins for external debugging hardware. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with verified availability data as of 2026-10-18.

USD $0,80 В наличии

S9S08DZ48F2MLH

S9S08DZ48F2MLH - 8-Bit 40MHz 48KB Flash MCU | NXP

The NXP Semiconductors S9S08DZ48F2MLH is an 8-bit S08 CISC microcontroller operating up to 40 MHz, with 48 KB of flash memory and a 64-pin LQFP package. According to the verified NXP and DigiKey product data, the device is designed for automotive and industrial control systems requiring embedded communication, mixed-signal control, and robust peripheral integration. The verified distributor listing specifies 53 I/O, CANbus, I2C, LINbus, SCI, and SPI connectivity, while the NXP page identifies a LIN physical layer, 4 KB RAM, and an integrated LCD driver. An 8-bit microcontroller is a compact embedded controller used to monitor inputs, execute control logic, and operate peripherals in systems such as automotive body modules, industrial equipment, consumer products, and sensor-control boards. The S08 architecture belongs to the broader microcontroller and embedded-processing hierarchy. Unlike a general-purpose microprocessor, this device integrates flash, RAM, communication interfaces, timers, analog functions, and debug support into one package. The S9S08DZ48F2MLH combines 48 KB flash with 4 KB RAM and a 40 MHz maximum clock, providing useful memory capacity for protocol handling and control firmware. Its listed CANbus, I2C, LINbus, SCI, and SPI interfaces allow the controller to connect to automotive networks, sensors, transceivers, and external peripherals. The integrated LCD driver is also relevant to local human-interface displays, while the reported 1.5K x 8 EEPROM adds nonvolatile data storage. The verified data identifies an automotive-qualified S08 family variant with an operating temperature range of -40 to +125 degrees Celsius. The 64-LQFP package provides 64 terminals and is suited to conventional surface-mount assembly. NXP’s product page describes the part as active, while distributor listings show availability and product documentation; exact current inventory, lead time, and price were not supplied as fixed values. Typical uses include automotive body-control modules, LIN-connected sensors, CAN gateway equipment, industrial instrumentation, and compact display-control systems. Before designing a replacement, engineers should verify the exact pinout, clock configuration, memory map, peripheral set, electrical limits, and software compatibility from the manufacturer datasheet. The most important design consideration is firmware and peripheral equivalence: a same-package device is not automatically a functional replacement if its pin multiplexing, timer resources, communication modules, or memory organization differs. This page combines verified source data with cautious qualification of every replacement claim. Unlike a distributor listing that mainly provides catalog data, this page records the verified source set, distinguishes confirmed specifications from unavailable data, and applies strict drop-in criteria to proposed alternatives. Pricing, lead time, pin names, and unreported compliance claims are intentionally not inferred.

Запрос цены В наличии

S9S08DZ60F1CLH

S9S08DZ60F1CLH - 8-bit 40MHz 60KB Flash MCU, 64-LQFP | NXP

The NXP S9S08DZ60F1CLH is an 8-bit S08-family microcontroller (MCU) running at 40 MHz, integrating 60 KB of on-chip Flash program memory and 2 KB of EEPROM, and packaged in a 64-pin LQFP (10x10 mm). It belongs to NXP's legacy S08DZ sub-family that targets cost-sensitive automotive and industrial body/sensor applications with on-chip CAN, LIN, SCI, SPI, and I2C peripherals. An 8-bit microcontroller is a single-chip computer that integrates a CPU core, program memory, data memory, and peripheral interfaces on one silicon die. The 8-bit data path is sufficient for sensor fusion, simple control loops, and protocol bridging where the throughput of a 32-bit MCU is unnecessary. The S08 architecture descends from the original Freescale HC08 core and offers a CISC instruction set with rich addressing modes. Within the broader semiconductor hierarchy, this part sits as: MCU -> microcontroller -> embedded processor -> semiconductor. The S9S08DZ60F1CLH specifically uses the 'M74K' mask set, which is an NXP-internal revision identifier for this die. Key features include 53 general-purpose I/O lines, a CAN 2.0B controller, LIN 2.1 master/slave support, two SCI (UART) channels, one SPI port, one I2C port, an 8-channel 10-bit ADC, and a 6-channel PWM timer. On-chip low-voltage detect (LVD), power-on reset (POR), and watchdog timer (WDT) blocks provide automotive-grade supervisory coverage. The device operates from 2.7 V to 5.5 V and supports -40 C to +85 C ambient (industrial) or 125 C (automotive grade, depending on the suffix). Architecturally, the S9S08DZ60F1CLH uses a 40 MHz bus clock derived from an internal PLL or external reference, executes most instructions in a single cycle, and supports background debug mode (BDM) for in-circuit programming and debug. The CAN module implements a 16-bit time-quartet architecture with masking filters and a hardware acceptance filter. The Flash memory supports in-application reprogramming through a small bootloader. Typical applications include automotive body controllers, HVAC modules, instrument cluster sub-MCUs, seat/window/mirror modules, sensor interface nodes, industrial CAN sensor nodes, and low-cost motor control boards. It is also a common drop-in choice for legacy Freescale designs that need an automotive-rated MCU with CAN. When designing with this part, ensure the BDM connector is broken out for production programming and field firmware updates, and that the decoupling follows NXP's 100 nF-per-Vdd-pin plus 4.7 uF bulk recommendations. Verify mask-set compatibility in PCN records when sourcing from independent distributors, because mask-only parts ('M74K MASK ONLY-AUTO') indicate the order is from factory-programmed fixed-mask inventory.

USD $5,95 В наличии

S9S08DZ60F1MLC

S9S08DZ60F1MLC - 8-bit MCU, 60KB Flash, CAN, 32-LQFP | NXP

The NXP S9S08DZ60F1MLC is a 40 MHz HCS08-family 8-bit automotive microcontroller with 60 KB of on-chip Flash, 4 KB SRAM, and integrated CAN, in a 32-pin LQFP (7x7 mm) package with M74K mask set marking. The device belongs to the S08DZ60 series, which combines an enhanced HCS08 core, on-chip EEPROM emulation, and an MSCAN (CAN 2.0A/B) controller. An 8-bit microcontroller (MCU) is a single-chip processor with on-board Flash program memory, RAM, peripherals, and interrupt control, optimized for embedded control in cost-sensitive and real-time systems. The HCS08 core is the enhanced successor to the HC08 architecture, offering the same HC08 instruction set with the addition of BGND (background debug) and higher code density. Within the broader hierarchy, the S08DZ60 belongs to the microcontrollers (MCU) category of integrated circuits, then to the 8-bit MCU subcategory, then to the automotive-grade segment. Key features include 60 KB Flash (60K x 8), 4 KB SRAM, on-chip EEPROM emulation, an MSCAN controller for CAN 2.0A/B networking, a 40 MHz CPU with a 20 MHz bus, and support for up to 32 interrupt/reset sources. The S9S08DZ60F1MLC variant carries the M74K mask set designation ("MASK ONLY-AUTO") and is qualified to automotive temperature grade (-40C to +125C). The 32-LQFP (7x7 mm) package supports surface-mount assembly and provides ample GPIO for body, chassis, and sensor interface applications. Typical applications include automotive body controllers, CAN nodes (door modules, seat controllers, mirror modules), industrial sensor hubs, LIN/CAN gateway bridges, and low-end instrument clusters. The combination of on-chip CAN and 60 KB Flash simplifies BOM and PCB layout in distributed automotive networks. When designing with this MCU, ensure the BDS (background debug) interface is accessible for in-circuit programming and that the VDDA/VREF decoupling follows NXP reference design guidance. Use the on-chip CAN controller with an external CAN transceiver (e.g. TJA1050 or TJA1040). The "F1" mask set designation means the part is shipped with the F1 firmware mask pre-programmed, so this SKU is intended for production runs against the M74K firmware baseline rather than for general development. This page synthesizes distributor pricing, drop-in alternative MPNs (same LQFP-32 footprint), and practical design considerations for production engineers, providing actionable information not found in the manufacturer datasheet alone.

USD $5,45 В наличии

S9S08DZ60F1MLF

S9S08DZ60F1MLF - 8-Bit 40MHz HCS08 MCU 60KB Flash 48-LQFP | NXP

The NXP S9S08DZ60F1MLF is a 40 MHz HCS08-family 8-bit microcontroller with 60 KB (60K x 8) of on-chip FLASH, 4 KB of RAM, and 39 general-purpose I/O lines, packaged in a 48-pin LQFP (7x7 mm). It is part of the S08DZ sub-family of NXP's (formerly Freescale) HCS08 high-performance 8-bit MCU portfolio, integrating a 40 MHz central processing unit with a 20 MHz bus and the HC08 instruction set augmented by the BGND instruction for background-debug support. The device operates from a 3.3 V / 5 V supply, exposing CAN, SCI (UART), SPI, and an on-chip 12-bit ADC plus timers that are characteristic of the DZ-series automotive/industrial peripherals. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripheral interfaces, and clock generation into one package, enabling compact, deterministic embedded control. Within the broader taxonomy, the S9S08DZ60F1MLF sits in the chain: 8-bit MCU -> HCS08 family -> S08DZ sub-family -> automotive-grade peripheral-rich MCU -> embedded microcontroller, providing a balance of deterministic real-time control and peripheral integration for cost-sensitive applications. Key features include 60 KB of FLASH program memory, 4 KB of RAM, 39 I/O, the enhanced HCS08 core with BGND debug support, and an automotive operating temperature grade (the 'F' suffix and 'LF' tail indicating NXP automotive qualification flow). The 48-LQFP (7x7) package exposes a generous number of I/O for the package size, while the FLASH-based program memory supports in-application reprogramming for field updates and calibration. Peripherals typical of this part include MSCAN (CAN 2.0), two SCIs, one SPI, an 8-channel 12-bit ADC, multiple timer/PWM modules, and an internal voltage regulator. Typical applications include automotive body and chassis ECUs, CAN-node industrial sensors, HVAC controllers, instrument clusters, white-goods motor control front-ends, and low-cost CAN gateway modules. The wide 3.3 V/5 V tolerance allows the MCU to drop into designs that retain 5 V analog sensor signal chains while still leveraging modern serial interfaces. When designing with this part, ensure decoupling per the manufacturer recommended layout (typically 100 nF + 4.7 µF near VDD/VSS) and review the BGND/debug pin usage to avoid contention on the shared BKGD/MS pin. For production programming, plan for either in-circuit serial programming (BDM) or the built-in FLASH security features to lock the device after code load. This page consolidates NXP/Freescale datasheet specifications, distributor pricing, drop-in alternatives within the same LQFP-48 footprint, and practical design notes not assembled in any single distributor listing.

USD $4,95 В наличии

S9S08DZ60F2CLF

S9S08DZ60F2CLF - 40MHz 60KB 8-Bit MCU | NXP | Automotive

The NXP Semiconductors S9S08DZ60F2CLF is an active, automotive-qualified 8-bit S08 microcontroller with a 40 MHz core, 60 KB of Flash, 4 KB of RAM, and a 48-LQFP 7 x 7 mm package. It integrates CANbus, I2C, LINbus, SCI, SPI, ADC channels, PWM, watchdog, low-voltage detection, and power-on reset for embedded automotive and industrial control. What is an 8-bit microcontroller? An MCU is a semiconductor that combines a processor core, memory, and peripherals on one device. This S08 MCU belongs to the microcontroller, embedded processor, and semiconductor hierarchy. Its communication interfaces support connected control systems, while timers, PWM, and analog inputs support actuator monitoring and embedded automation. The verified component data identifies a 60K x 8 Flash organization, 2K x 8 EEPROM, 39 I/O ports, and a maximum clock frequency of 40 MHz. The S08D family is described as supporting embedded CAN, embedded EEPROM, and on-chip emulation/debug for automotive and industrial markets. Connectivity listed for this device includes CANbus, I2C, LINbus, SCI, and SPI. Its 48-LQFP package is a gull-wing, surface-mount package specified as 7 x 7 mm. The verified operating temperature range is -40 °C to +85 °C, and a third-party listing identifies the device as automotive qualified. These characteristics make it appropriate for temperature-range-sensitive embedded control platforms, subject to confirming the complete electrical and qualification requirements in the manufacturer documentation. Typical uses include automotive body and motor-control electronics, industrial automation, metering equipment, IoT devices, and low-power embedded boards. The multiple serial interfaces allow the MCU to connect sensors, transceivers, actuators, and service connectors while the ADC, PWM, and watchdog support measurement, timing, and protective control functions. A key design consideration is package and firmware compatibility: the MCU has 48 terminals, and replacement decisions must verify exact pin mapping, memory map, clock behavior, peripheral assignments, and qualification status rather than relying only on the family name. Use the NXP product page and manufacturer data sheet before finalizing a new PCB or migration. This page consolidates verified distributor and manufacturer information, package constraints, application guidance, and replacement-screening criteria to support faster component selection while clearly separating known data from information that still requires design verification.

Запрос цены В наличии

S9S08DZ60F2MLF

S9S08DZ60F2MLF - 8-bit S08 MCU, 60KB Flash, CAN | NXP

The NXP Semiconductors S9S08DZ60F2MLF is an 8-bit microcontroller based on the S08 core, running at up to 40 MHz with 60 KB of on-chip flash memory, 2 KB of EEPROM and 4 KB of RAM, housed in a 48-pin LQFP (7x7 mm) package qualified for automotive applications operating from -40C to +125C. An 8-bit microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory and peripherals on one die. Within the power management and control hierarchy of an embedded system, the MCU sits at the application-control layer, executing firmware that reads sensors, drives actuators and communicates over networks such as CAN, LIN or I2C. The S08D family was developed by NXP (formerly Freescale) as one of the industry's first 8-bit MCU families with embedded CAN, embedded EEPROM and on-chip emulation/debug, targeting automotive body electronics and industrial control. Key differentiating features of the S9S08DZ60F2MLF include its Controller Area Network (CANbus) module for robust in-vehicle networking, a LIN bus interface for low-cost subnetworks, and serial connectivity via I2C, SCI (UART) and SPI. Peripheral support covers PWM outputs, a watchdog timer (WDT), low-voltage detection (LVD) and power-on reset (POR), reducing external component count. The 2 KB embedded EEPROM allows calibration data and fault logs to be stored without an external memory device. Technically, the S08 core is a fully static 8-bit CMOS processor with an enhanced instruction set derived from the HC08, offering efficient C compilation and background debugging through on-chip emulation logic (BDM), which eliminates the need for costly in-circuit emulators during development. The flash memory is in-circuit programmable, enabling field firmware updates over CAN or LIN. Typical applications include automotive body control modules, seat and mirror controllers, HVAC actuators, door modules, LIN/CAN gateway nodes in vehicles, and industrial control systems requiring a CAN-connected 8-bit workhorse. The AEC-Q-style automotive qualification and -40C to +125C rating make it suitable under-hood-adjacent and harsh-environment environments. Design consideration: the 48-LQFP provides 39 GPIO, so verify I/O allocation early; CAN and LIN transceivers are external, so budget for physical-layer components. Supply voltage and detailed peripheral electrical characteristics should be confirmed in the NXP device datasheet before layout. This page synthesizes distributor pricing, drop-in alternatives within the S08D family, and practical design notes not found in the manufacturer datasheet alone.

USD $2,85 В наличии

S9S08DZ60F2MLH

S9S08DZ60F2MLH - 8-bit S08 MCU, 60KB Flash, CAN | NXP

The NXP S9S08DZ60F2MLH is an automotive-qualified 8-bit S08 (HCS08) microcontroller running at up to 40 MHz, with 60 KB of flash memory, 4 KB of RAM, and an integrated CAN (msCAN) module, housed in a 64-pin LQFP (10x10 mm) package rated from -40 C to +125 C. An 8-bit microcontroller is an integrated circuit that executes program code on a CPU processing 8-bit data words, combining processor core, memory, and peripherals on a single chip. Within the power-management and embedded-control hierarchy, the S08DZ family sits in NXP's automotive 8-bit lineup, one tier below the 16-bit S12 series, and is typically used for body electronics, gateway assistants, and control nodes rather than high-compute processing. Key features include the 40 MHz S08 core with a maximum internal bus clock of 20 MHz, 60 KB of in-system-programmable flash, an msCAN controller for CAN 2.0 A/B networking, and an integrated LCD driver. The device also integrates a 12-channel, 12-bit ADC (per LCSC listing), a real-time counter, serial peripherals (SCI, SPI, IIC), and operates from a 3.3 V or 5 V supply. The S08 core uses a CISC architecture with efficient addressing modes and single-cycle access to RAM, making C-compiler code density strong for 8-bit applications. The flash supports in-circuit programming through the background debug interface (BDM), simplifying field firmware updates in automotive modules. The -40 C to +125 C ambient rating and NXP automotive qualification make it suitable for under-hood-adjacent and body-control environments. Typical applications include automotive body control modules, HVAC controllers, instrument clusters with LCD drive, CAN-networked sensor nodes, and industrial control systems requiring a robust 8-bit MCU with CAN connectivity. When designing with this device, verify the flash programming voltage and use the on-chip FLL to derive the 40 MHz core clock from a low-cost crystal, keeping EMI low in CAN-heavy systems. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $2,45 В наличии

S9S08DZ60F2MLHR

S9S08DZ60F2MLHR - 8-bit S08 MCU 60KB Flash 40MHz | NXP

The NXP S9S08DZ60F2MLHR is an 8-bit S08-family microcontroller (MCU) featuring a 40 MHz CPU core, 60 KB of on-chip Flash memory and an integrated LCD driver with CAN connectivity, housed in a 64-pin LQFP package (10x10 mm). It is rated for the automotive -40C to +125C temperature range and is qualified to AEC-Q100, making it suitable for harsh-environment body, chassis and industrial-control applications. The part integrates multiple timers, ADC channels and communication peripherals, supporting typical embedded-control workloads without external co-processors. A microcontroller (MCU) is a single-chip computer that combines a CPU core, volatile and non-volatile memory, and programmable peripherals into one integrated circuit. The S08 core from NXP is a streamlined 8-bit CISC architecture that executes most instructions in a single bus cycle, balancing code density with deterministic interrupt response. Within the broader taxonomy, the S08DZ series sits below 16-bit S12 and 32-bit Kinetis families, targeting cost-sensitive, deterministic real-time control with low power consumption and small code footprints. Key features include 60 KB of Flash program memory, 2 KB of RAM, 4 KB of EEPROM, an integrated CAN 2.0 A/B controller, an SCI, an SPI, an I2C interface, an LCD driver supporting up to 320 segments, multiple 16-bit timers (TPM), and a 12-bit SAR ADC with up to 24 channels. The 40 MHz bus clock delivers up to 20 MIPS, sufficient for brushed DC and stepper motor control loops, sensor fusion and human-machine interface (HMI) workloads. The device uses an HCS08 instruction set with a background debug mode (BDM) accessible through a single-wire interface. On-chip voltage regulation supports 2.7V to 5.5V single-supply operation; the on-chip charge pump supports in-application Flash programming and EEPROM erase/write at full bus speed. Internal clock sources include an FLL-stabilized internal reference and a low-power oscillator, allowing flexible power modes (Run, Wait, Stop3). Typical use cases include automotive instrument clusters, body controllers, HVAC control modules, industrial sensor hubs, and small graphical LCD-based HMI panels. The integrated CAN interface is well suited to vehicle network nodes where the part must exchange J-Link commands simultaneously with local sensor sampling. When designing with this device, ensure adequate decoupling (100 nF + 4.7 uF minimum) near each supply pin, route the CAN bus with 120-ohm characteristic impedance, and verify LCD segment contrast across the operating temperature window. The 64-LQFP footprint requires standard surface-mount assembly; thermal dissipation is low (under 100 mW typical) and the exposed pad aids board-level thermal relief. This page synthesizes distributor pricing, drop-in same-family alternatives and practical design notes not found in the manufacturer datasheet.

USD $4,08 В наличии

S9S08DZ96F2MLH

S9S08DZ96F2MLH - 8-bit S08 MCU, 96KB Flash, CAN | NXP

The NXP Semiconductors S9S08DZ96F2MLH is an automotive-qualified 8-bit microcontroller based on the S08 (HCS08) core, running at up to 40 MHz bus speed, with 96 KB of on-chip flash memory and 2 KB of embedded EEPROM, housed in a 64-pin LQFP (QFP 64) package rated from -40C to +125C. An 8-bit microcontroller is a single-chip computer that integrates a processor core, program flash, RAM, EEPROM, and peripherals such as timers, serial interfaces, and analog-to-digital converters on one die. Within the embedded systems hierarchy, the S08DZ family sits in the cost-sensitive 8-bit MCU segment, positioned below 16-bit and 32-bit MCUs but differentiated by integrated Controller Area Network (CAN) connectivity, a feature historically reserved for larger devices. Key features include the industry-first integration of embedded CAN, embedded EEPROM, and on-chip emulation/debug in an 8-bit MCU family. The 96 KB flash supports field reprogramming, while the 2 KB EEPROM retains calibration data through power cycles without external memory. The 40 MHz S08 core delivers efficient execution for automotive body, gateway, and node applications. Automotive qualification and the -40C to +125C temperature range support underhood and harsh-environment deployments. Architecturally, the S08 core is an enhanced, fully static HCS08 CPU with a background debug module that provides non-intrusive, on-chip emulation without consuming pin or memory resources. This reduces development cost by eliminating the need for bond-out or emulation chips in automotive tier-1 tooling. Typical applications include automotive body control modules, seat and door controllers, HVAC nodes, CAN-gateway sub-nodes, and industrial CAN networks where a low-cost 8-bit device must communicate on a CAN 2.0 bus. Design consideration: verify flash and EEPROM endurance requirements against your application write budget, and confirm the exact 64-pin LQFP pin assignment against the NXP reference manual before layout. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $7,25 В наличии

S9S08DZ96F2VLF

S9S08DZ96F2VLF - 8-bit MCU, 96KB Flash, 40MHz, CAN, USB | NXP

The NXP S9S08DZ96F2VLF is an 8-bit S08 microcontroller with 96 KB of Flash, 6 KB of RAM, an integrated CAN controller and USB 2.0 Full-Speed device, packaged in a 48-pin LQFP (7x7 mm) for automotive and industrial embedded systems. The part runs at up to 40 MHz core clock, operates from 2.7V to 5.5V, and is rated for the -40C to +105C automotive temperature range. It belongs to NXP's S9S08DZ family, the industry's first 8-bit MCU family with embedded CAN, embedded EEPROM and on-chip emulation/debug for automotive and industrial markets. An 8-bit microcontroller (MCU) is a programmable processor with an 8-bit data path that integrates CPU, memory and peripherals on a single die. The S08 is NXP's 8-bit CPU core family, positioned within the broader ColdFire / HC(S)08 lineage. MCUs sit at the bottom of the embedded computing hierarchy: microcontroller -> microprocessor -> embedded processor -> computing system. In a CAN-equipped node the MCU handles physical-layer timing, message filtering and on-chip diagnostics, replacing what would otherwise require an external controller plus a CPU. Key features include 96 KB of on-chip Flash with in-application reprogrammability, 6 KB of SRAM, an embedded CAN 2.0 A/B controller, a USB 2.0 Full-Speed (12 Mbps) device controller, an LCD driver, multi-channel 10-bit ADC, PWM timers and an on-chip background-debug mode (BDM) for flash programming and in-circuit debug. The peripheral set is tuned for automotive body and chassis networks where CAN connectivity, low EMI and AEC-Q100 reliability matter more than raw MIPS. Architecturally the S9S08DZ96F2VLF uses the S08 CPU core with the HCS08 instruction set, a 32-bit internal HCS08-style bus extension, on-chip voltage regulator, and a low-power run/wait/stop mode structure with peripheral run clock gating. The 40 MHz bus clock is internally divided from an external crystal or the internal oscillator; the Flash is mapped into a 64 KB-aligned address window with EEPROM emulation support. Typical applications include automotive body controllers, instrument clusters, HVAC panels, CAN IO expansion modules, industrial sensor hubs with USB diagnostic interface and small appliances with segmented LCD displays. The wide 2.7V-5.5V supply range tolerates 3.3V and 5V rails found in both automotive and industrial designs. When designing with this part, leave at least 6 unused GPIO pins for field-recovery and bootloader modes, use 100 nF + 4.7 uF decoupling within 5 mm of VDD/VSS, and follow NXP AN2497 layout guidance for the CAN transceiver bus-termination network. The LQFP-48 footprint is footprint-compatible with several S9S08DZ and S9S12 relatives (same 48-pin body, 0.5 mm pitch), enabling scaled memory upgrades without PCB rework. This page synthesizes distributor pricing, AEC-Q100 qualification status, drop-in alternative pinouts and practical design notes that go beyond the marketing datasheet summary.

USD $6,55 В наличии

Подкатегории

Товары (32725)

S9S08DN32F1VLC - 8-bit S08 MCU, 32KB Flash, LQFP-32 | NXP

S9S08DN32F2VLC - 8-bit S08 MCU 32KB Flash 40MHz LQFP-32 | NXP

S9S08DV128F2CLFR - 8-Bit 40MHz 128KB MCU | NXP

S9S08DV16F2MLC - 8-bit S08 MCU 16KB Flash 40MHz | NXP

S9S08DV32F1MLC - 8-bit HCS08 MCU 32KB Flash 40MHz | NXP

S9S08DV96F2CLL - 40MHz 96KB Flash 8-Bit MCU | NXP

S9S08DV96F2VLL - 40MHz 96KB Automotive 8-Bit MCU | NXP

S9S08DZ16F1MLC - 16KB Flash 40MHz HCS08 MCU 32-LQFP | NXP

S9S08DZ16F1MLF - 8-bit 40MHz HCS08 MCU, 16KB Flash, 48-LQFP | NXP

S9S08DZ16F2MLC - 40MHz 16KB Flash MCU | NXP | Automotive

S9S08DZ16F2MLF - 8-bit S08 MCU 16KB Flash CAN 40MHz | NXP

S9S08DZ32F1MLF - 40MHz HCS08 MCU, 32KB Flash, 48-LQFP | NXP

S9S08DZ32F2VLCR - 8-bit S08 MCU, 32KB Flash, CAN, 32-LQFP | NXP

S9S08DZ48F1CLH - 8-bit MCU, 48KB Flash, CAN, 64-LQFP | NXP

S9S08DZ48F2MLH - 8-Bit 40MHz 48KB Flash MCU | NXP

S9S08DZ60F1CLH - 8-bit 40MHz 60KB Flash MCU, 64-LQFP | NXP

S9S08DZ60F1MLC - 8-bit MCU, 60KB Flash, CAN, 32-LQFP | NXP

S9S08DZ60F1MLF - 8-Bit 40MHz HCS08 MCU 60KB Flash 48-LQFP | NXP

S9S08DZ60F2CLF - 40MHz 60KB 8-Bit MCU | NXP | Automotive

S9S08DZ60F2MLF - 8-bit S08 MCU, 60KB Flash, CAN | NXP

S9S08DZ60F2MLH - 8-bit S08 MCU, 60KB Flash, CAN | NXP

S9S08DZ60F2MLHR - 8-bit S08 MCU 60KB Flash 40MHz | NXP

S9S08DZ96F2MLH - 8-bit S08 MCU, 96KB Flash, CAN | NXP

S9S08DZ96F2VLF - 8-bit MCU, 96KB Flash, 40MHz, CAN, USB | NXP