Товары (44.000+)

TPS3700DDCT - 18V Window Comparator | Texas Instruments
TPS3700DDCT

TPS3700DDCT - 18V Window Comparator | Texas Instruments

The Texas Instruments TPS3700DDCT is an 18 V window voltage comparator with a 400 mV internal reference, two open-drain outputs, and a 6-pin SOT-23-THIN package. It operates from 1.8 V to 18 V and monitors one rail for overvoltage and undervoltage conditions. Its adjustable thresholds can extend detection down to 400 mV, while the open-drain outputs are rated to 18 V. A window comparator is a voltage supervisor that combines two threshold comparisons around a monitored signal. It belongs to the comparator and power-management IC hierarchy, where it is used to identify when a supply enters an allowed operating window or exits it because of an excessive low or high condition. The TPS3700 can therefore operate as a combined window detector or as two independent voltage monitors. Key features include a wide 1.8 V to 18 V supply range, threshold accuracy of -1.0% over temperature, 0.25% typical threshold accuracy, and 5.5 uA typical quiescent current. The two open-drain outputs can be pulled up to an external voltage up to 18 V. Built-in hysteresis helps reject brief glitches and maintain stable outputs, while external resistors set the monitored voltage range. The TPS3700DDCT uses two high-accuracy comparators and an internal 400 mV reference. One comparator monitors the lower threshold and the other monitors the upper threshold, allowing detection of undervoltage and overvoltage separately. The monitored voltage is scaled with external resistors, making the device suitable for systems where the rail is higher than the internal reference. Typical applications include industrial 24 V input-bus monitoring, battery-pack protection, DC power-supply fault detection, load-switch sequencing, and embedded systems that require a hardware voltage supervisor. Its low quiescent current is useful in battery-powered equipment, while the 18 V operating range supports higher-voltage industrial rails. When designing the circuit, choose resistor values to keep the sense-node voltage within the comparator input limits and use pull-up resistors appropriate for the open-drain outputs. Confirm the logic polarity of both outputs in the system controller because a fault indication can require inversion. Review the manufacturer datasheet for threshold, hysteresis, input-current, and absolute-maximum details before finalizing the PCB layout.

Запрос цены Контакты
TPS3700DSET - 18V Window Voltage Detector | Texas Instruments
TPS3700DSET

TPS3700DSET - 18V Window Voltage Detector | Texas Instruments

The Texas Instruments TPS3700DSET is a high-voltage (18 V) window voltage detector for overvoltage and undervoltage monitoring, featuring two high-accuracy comparators with an internal 400 mV reference and two open-drain outputs rated to 18 V. It is offered in a 6-pin WSON package measuring 1.5 mm x 1.5 mm with a propagation delay of 29 us (maximum). A window voltage detector is a type of voltage supervisor or comparator circuit that monitors an input rail and asserts an alert whenever the rail falls outside a programmer-defined upper and lower threshold. It belongs to the broader family of comparators (amplifier ICs) which sit within power management ICs, and is commonly used as a safety watchdog in microprocessor and DSP power systems. Compared to single-threshold comparators, the window detector adds redundancy by failing-fast on both excursions, which is critical for ASIC rails, battery stacks, and industrial 24 V systems. Key features include a wide supply voltage range of 1.8 V to 18 V, threshold accuracy of 1.0% over temperature (0.25% typical), a low quiescent current of 5.5 uA typical, and built-in hysteresis on both comparators to reject brief glitches without false triggering. The monitored thresholds are set via external resistor dividers referenced to the internal 400 mV band-gap, and the two open-drain outputs can be pulled up to as high as 18 V for direct interface to logic rails or opto-isolators. The TPS3700DSET uses a CMOS architecture with a precision bandgap reference and twin comparators, giving it a clean offset and temperature-stable trip point across the -40C to +125C junction temperature range. The wide supply tolerance also lets it operate directly from 12 V and 15 V industrial rails without pre-regulation. Typical applications include overvoltage and undervoltage monitoring on 12 V industrial rails, battery-pack protection in multi-cell stacks, system reset generation for DSPs and microcontrollers, fault detection in PLC and motor-drive systems, and redundant safety supervision in medical and automotive subsystems. When designing with this device, choose the resistor divider ratio so the monitored voltage equals 400 mV at the desired trip point; hysteresis is fixed by internal design, but selection of the resistor network affects overall accuracy and input bias current error. This page consolidates verified distributor pricing, drop-in alternatives, and practical design notes for engineers evaluating the TPS3700DSET as a window supervisor.

Запрос цены Контакты
TPS3701DDCR - 36V Window Comparator | Texas Instruments
TPS3701DDCR

TPS3701DDCR - 36V Window Comparator | Texas Instruments

The Texas Instruments TPS3701DDCR is a 36 V window voltage comparator with an internal 400 mV reference, two open-drain outputs, and a 1.8 V to 36 V supply range, packaged in a 6-pin SOT-23-THIN. It monitors overvoltage and undervoltage conditions in industrial, embedded, and power-management systems. The two precision comparators can operate together as a window detector or independently as two voltage monitors, while external resistors set the monitored thresholds. A window comparator is a specialized voltage-monitoring IC that compares an input voltage against programmed upper and lower limits. Unlike a simple power-supply supervisor, this device combines two precision comparators, a low-power 400 mV reference, and separate fault outputs. It belongs to the broader hierarchy of comparator, voltage supervisor, power-management IC, and semiconductor categories. Its open-drain outputs can pull fault lines or enable signals low and may be wired for wired-AND behavior when required by the system architecture. Key features include a wide 1.8 V to 36 V supply operating range, thresholds adjustable down to 400 mV, low typical quiescent current of 7 microamperes, and high threshold accuracy. The outputs, identified as OUTA and OUTB, are rated to 25 V for overvoltage and undervoltage signaling. The monitored voltage is established with external resistor networks, allowing the same device to address different system rails without changing the comparator package. The TPS3701 architecture is useful when a system must distinguish a valid operating window from an unsafe condition. Two open-drain outputs provide separate information for undervoltage and overvoltage events, helping a controller, protection circuit, or system-management block respond without interpreting a single ambiguous fault signal. The internal reference improves repeatability when the monitored rail is divided down to the reference range. Typical applications include industrial control systems, embedded power rails, battery-powered equipment, power-supply sequencing, automotive-style voltage supervision, and general overvoltage or undervoltage protection. The 36 V supply capability is useful for systems whose monitored rails exceed conventional low-voltage logic levels, while the open-drain outputs allow flexible pull-up selection and interface-level adaptation. When designing the circuit, verify the external resistor divider limits, open-drain pull-up voltage, monitored-voltage range, and output timing before connecting the device. The 6-pin SOT-23-THIN package requires careful placement and adequate copper area. Because the outputs are open-drain, each line needs an appropriate pull-up unless it is intentionally connected to another open-drain node. This page combines manufacturer specifications, distributor availability information, application guidance, and verified replacement analysis. It is intended to help engineers identify whether the TPS3701DDCR fits a voltage-window monitoring design and to distinguish genuine same-footprint replacements from parts that only provide similar monitoring functions.

Запрос цены Контакты
TPS3701DDCT - 36V Dual Window Comparator | Texas Instruments
TPS3701DDCT

TPS3701DDCT - 36V Dual Window Comparator | Texas Instruments

The Texas Instruments TPS3701DDCT is a dual window voltage detector with two precision comparators, a 400 mV internal reference, and two open-drain outputs rated to 25 V, packaged in a 6-pin SOT-23-THIN configuration. It operates from 1.8 V to 36 V and is designed for overvoltage and undervoltage monitoring. A window comparator is a voltage detector that checks whether an input voltage lies between programmable upper and lower thresholds. Unlike a general-purpose comparator, this device integrates two comparison channels and a reference, allowing one IC to monitor both rail boundaries. In the power-management hierarchy, it belongs to the comparator and voltage-supervisor family rather than a power-regulator family. Key features include the 1.8 V to 36 V supply range, a 400 mV internal reference, two open-drain outputs, and monitoring flexibility through external resistor networks. The open-drain outputs can be pulled up to an appropriate external voltage, allowing wired interface use and flexible system-level signaling. Reported low quiescent current is approximately 7 µA typical, making the device suitable for low-power monitoring systems. The TPS3701 can operate as a window detector or as two independent voltage monitors. The monitored thresholds are established with external resistors, while the internal reference provides the comparison basis. Its high-voltage operating range allows monitoring of industrial supplies and other rails where input transients or nominal voltages exceed the range of simpler low-voltage supervisors. Response time is reported in distributor data as approximately 155 µs. Typical applications include industrial automation, battery systems, power-supply protection, sensor interfaces, and embedded control systems. It is especially useful when a system must assert separate fault signals when a monitored voltage becomes too high or too low. Because the outputs are open-drain, pull-up resistors are required unless the output is connected directly to a compatible pull-up arrangement. Designers should verify the full datasheet pinout, threshold tolerances, timing, output ratings, and capacitor or resistor recommendations before production. The SOT-23-THIN footprint supports compact layouts, but the open-drain pins and monitor-input network require careful routing. For replacements, compare the complete pinout and threshold architecture rather than selecting a part only by supply voltage or package name. This page combines verified manufacturer information, distributor pricing references, and practical design guidance.

Запрос цены Контакты
TPS4141-Q1 - 1200V Configurable Divider | Texas Instruments
TPS4141-Q1

TPS4141-Q1 - 1200V Configurable Divider | Texas Instruments

The Texas Instruments TPS4141-Q1 is a high-voltage precision matched resistor divider with an integrated programmable-gain amplifier (PGA), designed for accurate high-voltage measurement in automotive and industrial applications. The device supports input voltages up to 1200V and provides four configurable divider ratios via the DIV0 and DIV1 inputs. It is available in a 10.30mm × 10.30mm SOIC-11 (DWQ) package, optimized for space-constrained automotive systems. A high-voltage precision resistor divider is a specialized analog front-end IC that scales high-voltage inputs down to a safe range for downstream ADC or microcontroller measurement. It combines matched precision resistors with a PGA to maintain accuracy across temperature and voltage extremes, eliminating the need for discrete resistor networks and trimming. This architecture reduces board area and improves measurement reliability in high-voltage environments. The TPS4141-Q1 integrates a high-voltage switch that connects or disconnects the high-voltage sense pin, providing uni-directional current blocking when disconnected. The programmable-gain amplifier supports four divider ratios using DIV0 and DIV1, enabling flexible measurement scaling for different voltage ranges. External precision reference voltage can be supplied from REF to HVGND for bi-directional voltage measurement, and switching between uni-directional and bi-directional sensing during operation is possible. The device is AEC-Q100 qualified for automotive applications, ensuring robust performance over a wide temperature range. Its high-voltage capability and integrated switch make it suitable for battery management systems, traction inverters, and industrial motor drives where precise voltage monitoring is critical. The integrated PGA and matched resistors provide high accuracy, reducing system calibration overhead. Typical applications include electric vehicle battery pack voltage monitoring, solar inverter DC bus sensing, and industrial 24V/48V system voltage measurement. The high-voltage switch allows the sense line to be disconnected for safety or power saving, while the divider ratios allow the same device to serve multiple voltage ranges. Designers should ensure proper PCB clearance and creepage distances for 1200V operation, and use the external REF for bi-directional measurements when needed.

Запрос цены Контакты
TPS65193RGER - Dual High-Voltage TFT-LCD Scan Driver | TI
TPS65193RGER

TPS65193RGER - Dual High-Voltage TFT-LCD Scan Driver | TI

The Texas Instruments TPS65193RGER is a dual high-voltage scan driver for amorphous-silicon-gate TFT LCD panels, providing high-voltage gate-line outputs from -28 V to 35 V in a 24-VQFN 4 mm x 4 mm package. Each scan-driver section accepts a logic-level CPV input and produces complementary CKV and CKVB outputs, while a logic-level STV input generates the high-voltage STVP output. A high-voltage scan driver is a specialized interface IC that transfers low-voltage timing commands from the host controller to the elevated voltages required by TFT gate lines. Its position in the display hierarchy is controller interface, then row-driver interface, then gate-line scan driver. This device does not process image data; instead, it supplies the high-voltage, charge-sharing waveforms that select and bias TFT rows. Key features include a 35 V high output-voltage level, an output swing down to -28 V, scan-driver output charge sharing, and four logic-level inputs. The 24-VQFN package measures 4 mm on each side, supporting compact display-module designs where connector count and board area are constrained. The RGER orderable designation identifies the 4 mm x 4 mm VQFN package configuration. Each high-voltage scan driver receives CPVx and generates two outputs, CKVx and CKVBx. A separate STV logic input produces the STVP output. Charge sharing reduces peak drive demand by transferring charge between the complementary outputs rather than driving each output as an isolated hard switch, helping lower switching loss in the gate-line drive network. Typical applications are amorphous-silicon TFT LCD modules, including small-panel monitors, portable instruments, industrial HMIs, test equipment, and control-system displays. The device is most appropriate where the panel requires negative off-level and positive high-level gate drive but does not require a separate source-driver solution from the same device. Designers must account for the -28 V to 35 V output range, provide suitable bypassing on the high-voltage supply rails, and validate output timing against the target TFT panel. Panel bias requirements, leakage into neighboring rows, and clock-edge placement determine whether the charge-sharing outputs provide adequate settling time. This page consolidates the verified manufacturer and distributor information, separates documented specifications from unavailable data, and provides application guidance and comparison considerations that are not presented as a substitute for the complete Texas Instruments datasheet.

Запрос цены Контакты
TPS65195YFFR 8-Channel Display Level Shifter | TI
TPS65195YFFR

TPS65195YFFR 8-Channel Display Level Shifter | TI

The Texas Instruments TPS65195YFFR is an 8-channel display power and level-shifting integrated circuit packaged in a 30-pin DSBGA. Distributor records classify the device as a video processing IC and an 8-channel level shifter, placing it within the display-interface and video-signal-conversion segment of integrated-circuit applications. Its defining verified characteristics are the eight-channel architecture, display-oriented level-shifting function, and compact 30-DSBGA package. Detailed electrical ratings, supported logic standards, voltage limits, timing values, and thermal limits were not included in the supplied source material and therefore require confirmation from the manufacturer datasheet before schematic or layout release. A display level shifter is an interface IC that translates signals between voltage domains that use different electrical thresholds. This allows a host processor, graphics engine, or display controller to communicate more reliably with display-panel circuitry when input and output levels are not directly compatible. In the broader semiconductor hierarchy, the TPS65195YFFR belongs to interface ICs and, more specifically, to video interface ICs. Its eight channels allow multiple display-related signals to be handled within one package, reducing the component count compared with discrete translators. The verified distributor listing identifies the part as an 8-channel level shifter in a 30-pin DSBGA. This combination can be valuable in compact display modules where board area is constrained and several voltage-domain crossings are required. The BGA form factor also supports dense routing, although it demands assembly processes capable of handling fine-pitch balls. Package dimensions, ball pitch, exposed-pad details, soldering profiles, and reflow requirements must be taken from the official package drawing rather than inferred from the distributor description. Typical design use is a display controller interface, an LCD panel bias or signal interface, and a compact embedded display module. These uses follow from the verified display power and level-shifting classification; the supplied data does not enumerate supported panel interfaces or timing standards. Engineers should therefore treat the TPS65195YFFR as a display-interface candidate, not as a complete or independently characterized video processor, until channel direction, signal type, voltage ranges, and timing constraints are verified. A key implementation consideration is validating every connected display signal against the manufacturer's absolute-maximum and recommended operating limits. Because no pinout was supplied in the verified results, no pin assignments are asserted here. The official datasheet and land-pattern information must be used to confirm signal direction, supply pins, ground pins, and unused-ball handling before PCB routing begins. This page consolidates the verified distributor identity, package, and sourcing information with a structured engineering workflow for datasheet validation, alternative qualification, and display-interface design. It distinguishes confirmed facts from unavailable parameters rather than filling gaps with guessed electrical values.

Запрос цены Контакты
TPS65197RUYR - 8-Channel LCD Level Shifter | Texas Instruments
TPS65197RUYR

TPS65197RUYR - 8-Channel LCD Level Shifter | Texas Instruments

The Texas Instruments TPS65197RUYR is an 8-channel level-shifter IC for LCD display applications, packaged in a 28-pin WQFN (RUY) package measuring 4 mm by 4 mm. It supports 2-channel and 3-channel charge-sharing methods, normal level-shifting operation, and panel discharge to VGH during shutdown. The device is designed to translate timing-controller logic-level signals into the higher gate-level signals required by gate-in-panel (GIP) LCD panels. TPS65197RUYR belongs to the interface IC and display-driver ecosystem. A level shifter is an interface IC that translates voltage domains while preserving signal timing and logic function. In an LCD system, the timing controller operates at lower logic voltages, while GIP row and column driver circuits may require elevated panel voltages. The TPS65197 provides eight channels for this signal conversion and supports panel-specific charge-sharing sequences that help control panel charging and discharge behavior. The principal feature set includes eight level-shifting channels, support for no-charge-sharing, 2-channel charge-sharing, and 3-channel charge-sharing operation, and a dedicated panel-discharge function. The manufacturer product page identifies the device as an 8-channel level-shifter supporting 2-channel and 3-channel charge-sharing and panel discharge in the WQFN (RUY) package with 28 pins. Because GIP panels can accumulate charge and generate transient loads during startup, the charge-sharing architecture is important. The supported operating modes let a system select a charging strategy according to panel timing requirements rather than using a simple fixed level translation approach. The shutdown discharge path provides a defined mechanism for returning panel nodes toward VGH during power-down. Typical uses include notebook computer LCD panels, desktop monitors, television panels, and other GIP-based display systems. The device is most appropriate when the source logic levels, panel gate-drive levels, supported charge-sharing sequence, and shutdown behavior must all be evaluated together. A replacement should not be selected solely by channel count; the timing of each output, panel discharge behavior, voltage ratings, and board footprint must be confirmed against the original design. This page combines the verified manufacturer description, distributor package information, drop-in alternatives, and engineering-oriented design guidance. The 28-pin WQFN footprint, exposed thermal pad, high-speed panel signals, and power-sequencing requirements should be reviewed against the complete manufacturer datasheet before layout or replacement qualification.

Запрос цены Контакты
TPS65198RUYR - 13-Channel LCD Level Shifter | Texas Instruments
TPS65198RUYR

TPS65198RUYR - 13-Channel LCD Level Shifter | Texas Instruments

The Texas Instruments TPS65198RUYR is a 13-channel level shifter with an integrated operational amplifier for LCD televisions and monitors, supplied in a 28-pin WQFN (RUY) package measuring 4 x 4 mm. It supports an operating temperature range of -40 C to +85 C and is designed for display-interface applications where multiple voltage domains and signal buffering are required. A level shifter is an interface IC that translates logic signals between voltage domains whose high and low thresholds differ. In an LCD television or monitor, source electronics, timing controllers, panel interfaces, and backlight systems may operate from different supply rails. A multi-channel level shifter allows those signals to cross between incompatible voltage domains, while the integrated operational amplifier provides buffering for a signal that requires drive or amplification. The TPS65198RUYR's 13-channel architecture consolidates multiple translated logic connections in one package. This can reduce the number of discrete level-shifter components and simplify printed-circuit-board layout compared with a collection of individual translators. Its 4 x 4 mm WQFN format also supports compact display-control designs where connector density and panel-interface routing leave limited board area. The verified operating temperature range is -40 C to +85 C, covering industrial temperature conditions commonly encountered in display electronics. The available LCSC listing identifies an 8 V to 20 V supply-related value, but the provided source excerpt does not clearly identify that parameter or its test conditions; consequently, voltage limits, channel direction, translation thresholds, and the integrated amplifier's electrical ratings require confirmation in the manufacturer datasheet before design release. Typical uses include LCD monitor panel-interface circuits, television timing and control boards, display power-sequence logic, and other multi-rail display systems where a compact level-translation stage is needed. Because this device combines translation and amplification, it can simplify signal-interface design when the source impedance and loading requirements of the translated channels differ. Engineers should confirm every channel's direction, voltage domain, enable behavior, and the exposed-pad connection directly against the TI datasheet and the PCB footprint. The 28-pin WQFN package is also thermally and assembly sensitive; proper land-pattern compliance, paste control, and exposed-pad soldering are required for reliable production yield. This page consolidates the verified manufacturer identification, distributor package data, temperature rating, and supply-range excerpt for TPS65198RUYR, while clearly separating missing electrical data from confirmed values. It also documents the absence of a manufacturer-verified drop-in substitute rather than presenting an unverified package conversion as a drop-in replacement.

Запрос цены Контакты
TPS65198RUYT - 13-Channel Level Shifter | Texas Instruments
TPS65198RUYT

TPS65198RUYT - 13-Channel Level Shifter | Texas Instruments

The Texas Instruments TPS65198RUYT is a 13-channel level shifter with an integrated operational amplifier for GIP-based LCD television and monitor applications, packaged in a 28-pin WQFN (RUY) 4 x 4 mm package. It accepts five timing-controller input signals, uses an internal state machine to generate twelve output signals, and combines level shifting with op-amp signal conditioning. Its specified operating-temperature range is -40°C to +85°C. A level shifter is an interface device that translates logic-voltage levels so circuits using different voltage domains can communicate reliably. In this application, the TPS65198 belongs to the display-driver interface hierarchy: logic level translation, display timing-interface conversion, voltage-domain interfacing, and display-driver ICs. Its integrated op amp provides an additional analog signal-conditioning function alongside the digital level-shift outputs. The principal feature is the combination of a 13-channel level-shifting architecture, five external inputs, twelve internally generated outputs, and op-amp integration. This consolidation can simplify the circuitry associated with GIP panel timing control. The built-in state machine sequences the generated outputs according to the panel-interface requirements, while the integrated amplifier can support signal conditioning where the timing interface requires amplification or level adjustment. TPS65198RUYT is intended for LCD TVs and monitors using GIP technology, where multiple panel signals must be shifted between source-driver, gate-driver, and timing-controller voltage domains. The 4 x 4 mm WQFN package supports compact display-controller boards, but its exposed thermal-pad construction requires careful PCB layout for electrical return paths and heat spreading. Designers should also account for the high-speed edge behavior of the interface when routing signals and selecting input and output impedance. Typical uses include large-panel LCD television timing control, LCD monitor panel interfaces, and other GIP display systems that require coordinated multi-channel level translation. Because the verified source set identifies a 28-pin WQFN package and a -40°C to +85°C range, the device is appropriate for industrial and consumer display environments requiring operation across that temperature span. The principal design consideration is to follow the manufacturer datasheet exactly for exposed-pad connection, decoupling, signal routing, and output-state sequencing. Place input and output return paths close to the device, provide the specified supply and bypass capacitance, and avoid introducing stubs on timing signals. Verify every panel connector voltage domain and the state-machine timing before releasing a display board. This page consolidates the verified manufacturer and distributor information, distinguishes a true drop-in replacement from a packaging-only ordering variant, and highlights application-specific design considerations that are not apparent from a basic distributor listing.

Запрос цены Контакты
TPS66021YBGR - 20V Sink, 5V Source USB-C Switch | TI
TPS66021YBGR

TPS66021YBGR - 20V Sink, 5V Source USB-C Switch | TI

The Texas Instruments TPS66021YBGR is a one-channel integrated USB-C Power Delivery source-and-sink power multiplexer with a 20V sink path, a 5V source path, and a 5V dead-battery VBUS LDO, housed in a 28-ball DSBGA package measuring 1.61 mm by 2.81 mm. It combines two directional power paths in a compact device intended to manage charging, powering, and protection around a USB-C connection. A USB-C power-path multiplexer is a specialized power-management integrated circuit that controls current between a connector and internal supply rails. It belongs to the hierarchy power multiplexer, power-path controller, power-management IC, and semiconductor. By combining source and sink switching, it can route external VBUS power into a system, provide regulated 5V power from an internal source, and isolate paths during faults or operating-mode changes. The verified manufacturer data identifies a 4V-to-22V sink power path and a 5V source path. The source path enters constant-current operation when its load exceeds the selected current-limit threshold. Each path includes overtemperature and reverse-current protection, while the family supports a fault indication for overcurrent and overtemperature events. The integrated high-voltage VBUS LDO provides 5V for this device and other system components under dead-battery conditions. The TPS66021 integrates a 20V USB-C sink capability and 5V source capability rather than acting only as a passive analog switch. Its VBUS-side architecture allows the system to distinguish and control external power conditions, while the source path supplies a defined output level. The fault function gives the host circuitry a signal when protection circuitry has detected an abnormal event, enabling controlled shutdown or fault recovery. Typical uses include USB-C laptop and tablet power adapters, portable equipment, battery-powered industrial products, and compact systems that must accept external USB-C power while retaining a safe internal 5V supply. The integrated source, sink, and dead-battery functions can reduce board area compared with a discrete switch network. Designers must still validate connector orientation, CC behavior, capacitor selection, current limits, thermal performance, and system power sequencing against the full manufacturer documentation. For PCB layout, follow the manufacturer package land pattern and place high-current input, output, and ground connections with short, wide paths. Place required input and output capacitors close to their associated balls and keep sensitive control and fault traces away from high-di/dt power loops. Verify the selected current threshold, startup behavior, and fault response in the final USB-C system. This page consolidates verified manufacturer descriptions, distributor availability, package information, replacement evidence, and application guidance. It also distinguishes confirmed facts from parameters that require the complete datasheet, preventing unsupported electrical or compliance assumptions during design review.

Запрос цены Контакты
TPS8802DCPR - Smoke Alarm AFE with CO Support | TI
TPS8802DCPR

TPS8802DCPR - Smoke Alarm AFE with CO Support | TI

The Texas Instruments TPS8802DCPR is a smoke-alarm analog front end (AFE) for residential smoke detectors, integrating the regulators, amplifiers, and drivers required for a dual-wave photoelectric smoke alarm and carbon monoxide detection system. The verified distributor listing identifies a 38-pin HTSSOP package and analog input with I2C output. TI describes the device as a high-performance, multi-channel, digital-input solution whose flexible architecture suits smoke-alarm systems where precision and power consumption are critical. What is a smoke-alarm analog front end? An AFE is a semiconductor that connects physical sensing elements to an embedded system. In a photoelectric alarm, light scattering and light-absorption signals require controlled excitation, amplification, filtering, and diagnosis. The TPS8802DCPR integrates those signal-chain functions together with supporting regulators and drivers, reducing the number of discrete components and helping designers create a compact, low-power detector platform. The verified TI product information highlights a wide input-voltage range, low standby-power consumption, and power-saving features designed to support 10-year battery-powered smoke-alarm systems. Its dual-wave photoelectric architecture and CO-detection capability allow one integrated platform to combine optical smoke sensing with electrochemical CO-sensor signal conditioning. The I2C interface provides a digital control and diagnostic path, while the analog input supports direct connection to sensing circuitry. The TPS8802DCPR is intended for residential smoke alarms, combination smoke-and-CO alarms, and other safety products requiring highly integrated sensing support. Its integrated regulators and amplifiers can simplify power-tree design compared with a discrete implementation, while digital configuration can support manufacturing tests and field diagnostics. Exact electrical limits, gain settings, timing values, and pin functions were not included in the supplied verified records and therefore require confirmation from the manufacturer datasheet before design release. For battery operation, standby current is especially important because the target application is a long-lived safety device. Designers should calculate average and peak current across the sensing duty cycle, confirm regulator startup behavior, and verify that low-power modes preserve alarm thresholds and diagnostic performance. The I2C pull-up arrangement, grounding, and decoupling should follow the manufacturer layout guidance to prevent communication errors or unintended current consumption. This product page consolidates the verified distributor classification, manufacturer application description, package information, source links, and design cautions. It does not invent electrical parameters or claim unverified drop-in equivalents. Confirm the complete pinout, absolute maximum ratings, recommended operating conditions, and lifecycle status in the current Texas Instruments documentation before schematic capture or PCB release.

Запрос цены Контакты
TPS8804DCPR - Analog Front End for Commercial Smoke Detector | Texas Instruments
TPS8804DCPR

TPS8804DCPR - Analog Front End for Commercial Smoke Detector | Texas Instruments

The Texas Instruments TPS8804DCPR is an integrated analog front end (AFE) and system power management IC for commercial smoke detectors. Housed in a 38-pin HTSSOP (DCP) package, it integrates multiple functions including photoelectric chamber driver circuitry, a piezo buzzer driver, an I2C communication interface, and a low-dropout (LDO) regulator chain to support battery-powered smoke alarm designs. A smoke detector AFE is a specialized analog front end that combines the bias and signal-conditioning paths used by optical or ionization smoke sensors with the housekeeping functions needed to run a battery-powered alarm. The TPS8804DCPR falls within the broader family of sensor and detector interface ICs that sit between the physical sensor element (photodiode or ionization chamber) and the system microcontroller or horns driver. Its role is to power, bias, read, and test the sensor while managing battery life, supervisory housekeeping, and interconnect functions across multi-unit networked installations. Key features include analog signal paths for both photoelectric and ionization smoke sensor types, an integrated boost converter for high-current piezo buzzer drive, an integrated LDO chain for system rails, an I2C interface for configuration and status readback, an interconnect driver for interlinking multiple smoke alarm units in a building, and on-chip timers for sensor self-test. The IC is intended for use with an external MCU that runs the smoke detection firmware. Operating voltage is designed to support common 9V battery and regulated mains-powered topologies. The TPS8804DCPR is optimized for ultra-low standby current so the detector can sit on a battery for years without replacement, while still providing rapid sensor biasing and high-current piezo drive during an alarm event. Its integrated boost converter eliminates the need for a discrete driver MOSFET and inductor for the buzzer, reducing BOM count. The HTSSOP-38 package provides adequate thermal dissipation for the piezo boost stage at typical alarm sound pressure levels. Typical applications include residential and commercial smoke alarms, CO-and-smoke combination detectors, heat detectors with piezo alarms, and industrial safety notification appliances. The interconnect feature lets installers link multiple units so that all alarms sound when any one unit triggers, a key requirement for multi-room buildings. When designing with this part, follow the reference layout in the TPS8804 datasheet for the boost inductor and feedback loop. Use low-leakage ceramic capacitors on the photo-sensor input to preserve low standby current and accurate chamber biasing. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты
TRS3221EIDBR - 3-5.5V RS-232 Transceiver, ±15kV ESD | Texas Instruments
TRS3221EIDBR

TRS3221EIDBR - 3-5.5V RS-232 Transceiver, ±15kV ESD | Texas Instruments

The Texas Instruments TRS3221EIDBR is a 3-V to 5.5-V single-channel RS-232 line driver/receiver with ±15-kV IEC-ESD protection, packaged in a 16-pin SSOP (DB). It operates from a single supply rail and integrates a charge-pump that generates the ±RS-232 voltage swing from the input supply, so no external ±12 V rails are required. The device supports data rates up to 250 kbps and is rated for ±15-kV HBM, ±8-kV IEC 61000-4-2 contact, and ±15-kV IEC 61000-4-2 air-gap ESD strikes on the RS-232 bus pins. An RS-232 transceiver is a type of line driver/receiver IC that converts logic-level (typically 0/3.3 V or 0/5 V CMOS/CMOS) UART signals into the ±5 V to ±15 V voltage swings required by the TIA/EIA-232-F and ITU v.28 standards. It belongs to the broader interface-IC category, sitting between the UART block of a microcontroller/SoC and a DB-9 (or equivalent) connector on the serial port. Single-channel variants like the TRS3221E serve compact, point-to-point designs where two driver/receiver channels are not needed, helping shrink BOM cost and PCB area versus 2-channel parts. Key features include 1 driver and 1 receiver per channel, a dedicated enable input for power management, an auto-powerdown mode that drops quiescent current to 1 µA typical when the cable is disconnected, and an always-active supplementary receiver that monitors the ring-indicator path even in shutdown. The device meets or exceeds the TIA/EIA-232-F and ITU v.28 electrical specifications, and is offered in industrial temperature grades of -40 °C to +85 °C. A high-speed pin-compatible upgrade, the TRSF3221E, is available where 1 Mbit/s operation is required. The TRS3221E uses an on-chip switched-capacitor voltage converter with four external 0.1 µF charge-pump capacitors. The architecture tolerates supply rails as low as 3.0 V while still generating compliant ±5 V (minimum) RS-232 output swings, which is the headline advantage over legacy 5-V-only RS-232 transceivers. Drivers are slew-rate limited to keep EMI low, and the receivers include hysteresis to reject noise on long cables. Typical applications include industrial single-port serial ports, point-of-sale terminals, handheld data collectors, factory automation equipment, medical instruments with DB-9 serial interfaces, and any embedded system that needs a robust RS-232 link from a 3.3 V or 5 V UART. Designers often pair this part with a TVS array for additional surge protection when the cable is exposed to outdoor or industrial transients. When designing with the TRS3221EIDBR, place the four charge-pump capacitors (typically 0.1 µF X7R) as close as possible to the C0+, C0-, C1+, C1- pins to minimize supply ripple. Decouple VCC with a 0.1 µF + 1 µF combination near the pin, and respect the absolute-maximum ratings on the RS-232 outputs (typically ±13.2 V) by avoiding back-drive when the IC is unpowered. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
TRS3221EIRGTR - 3-5.5V RS-232 Transceiver, 250kbps, ±15kV ESD | Texas Instruments
TRS3221EIRGTR

TRS3221EIRGTR - 3-5.5V RS-232 Transceiver, 250kbps, ±15kV ESD | Texas Instruments

The Texas Instruments TRS3221EIRGTR is a 3- to 5.5-V single-channel RS-232 line driver/receiver delivering 250 kbps data rate with ±15 kV IEC-ESD protection in a 16-pin VQFN (RGT) package measuring 3x3 mm with an exposed thermal pad. The device integrates one driver and one receiver, supports VCC operation from 3.0 V to 5.5 V (compatible with TTL/CMOS logic levels), and meets or exceeds the requirements of TIA/EIA-232-F and ITU v.28 standards. An RS-232 transceiver is a charge-pump-based interface IC that translates between TTL/CMOS logic levels (0-3.3 V or 0-5 V) and the ±5 V to ±15 V swing required by the legacy TIA/EIA-232-F serial communication standard. RS-232 transceivers belong to the broader interface IC family, which sits hierarchically between discrete level-shifters and protocol controllers (UARTs) in wired communication systems. RS-232 remains widely deployed in industrial equipment, point-of-sale terminals, medical instruments, and embedded debug ports where simplicity, point-to-point connectivity, and proven robustness outweigh the bandwidth advantages of USB or Ethernet. Key features include ±15 kV Human-Body Model (HBM) ESD protection on RS-232 pins, ±8 kV IEC 61000-4-2 contact discharge, ±15 kV IEC 61000-4-2 air-gap discharge, and an automatic powerdown feature that disables drivers when no valid RS-232 cable is detected. The on-chip dual charge pump requires only four external 0.1 µF capacitors, enabling true 5 V operation from a single 3.3 V supply without a separate ±12 V rail. The 250 kbps data rate is adequate for all standard RS-232 baud rates up to and beyond 115200 with margin to spare. The architecture combines a regulated switched-capacitor voltage doubler/inverter with a proprietary low-dropout RS-232 driver stage and a precision hysteresis receiver. ESD protection is implemented at the cable-side pins using TI's integrated silicon-controlled-rectifier (SCR) clamps. The 16-pin VQFN package's exposed pad provides a low thermal resistance path, which is useful when the part operates near the upper end of its 1 mA quiescent current budget in warm enclosures. Typical applications include industrial PLC programming ports, point-of-sale (POS) terminals, medical device serial consoles, battery-powered handhelds, and embedded debug UARTs that need robust ESD performance in the field. The TRS3221EIRGTR's small 3x3 mm footprint suits space-constrained designs such as USB-to-serial dongles, IoT gateways, and barcode scanners. When designing with this part, place the four charge-pump capacitors as close as possible to the C1+ / C1- / C2+ / C2- pins and keep the RS-232 trace lengths short to maximize ESD margin. Note that the TRSF3221E is the higher-speed (1 Mbit/s) pin-compatible alternative if 250 kbps is insufficient. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
TRSF3222CPW - 3V-5.5V RS-232 Transceiver, 2/2 Drivers | TI TSSOP-20
TRSF3222CPW

TRSF3222CPW - 3V-5.5V RS-232 Transceiver, 2/2 Drivers | TI TSSOP-20

The Texas Instruments TRSF3222CPW is a 2-driver/2-receiver RS-232 line transceiver that operates from a single 3.0V to 5.5V supply in a 20-pin TSSOP package. It supports data rates up to 1 Mbit/s and accepts 5-V logic inputs when powered from a 3.3V rail, making it ideal for mixed-voltage system designs. A line transceiver is an interface device that bridges a logic-level UART (universal asynchronous receiver/transmitter) on a host microcontroller with the RS-232 standard, which swings between +12V and -12V on the bus side. It sits within the Interface IC hierarchy (RS-232 transceiver -> line transceiver -> interface IC -> integrated circuit) and converts TTL/CMOS logic levels to TIA/EIA-232-F compliant voltage levels while protecting the host from ESD events on the cable side. The TRSF3222CPW integrates a dual charge-pump that generates the required +5.5V and -5.5V rails from a single 3.3V supply using four small 0.1 uF external capacitors. Standby current is typically 1 uA, supporting low-power portable designs. The receivers remain active in shutdown, allowing wake-up characters to be detected without waking the host. ESD protection exceeds +/-15 kV HBM on the bus pins. Typical applications include industrial point-of-sale terminals, factory automation equipment, portable diagnostic instruments, and battery-powered barcode scanners where 3.3V logic must communicate with legacy RS-232 peripherals. The wide 3.0V-5.5V supply range also makes the part suitable for USB-to-serial bridges and embedded computing modules. When designing with this device, place the four charge-pump capacitors as close to the IC as possible to minimize loop inductance. The TSSOP-20 footprint requires standard surface-mount assembly with a maximum reflow temperature per JEDEC J-STD-020. Decouple VCC with a 0.1 uF ceramic plus a bulk tantalum if the supply impedance is high.

Запрос цены Контакты
TS3022ID - Dual High-Speed Rail-to-Rail Comparator | STMicroelectronics
TS3022ID

TS3022ID - Dual High-Speed Rail-to-Rail Comparator | STMicroelectronics

The STMicroelectronics TS3022ID is a dual high-speed comparator with rail-to-rail input stages, push-pull outputs, and operation from 2 V to 5 V supply voltage. The device is specified for a wide -40 °C to +125 °C temperature range and is packaged in an 8-SOIC package. Each comparator channel provides independent inputs and a push-pull output, making the TS3022ID suitable for dual-threshold, window-detection, line-driver, and signal-conditioning applications. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input becomes higher than the other. The TS3022 belongs to the comparator hierarchy within analog and mixed-signal semiconductors, where its low supply-voltage operation and rail-to-rail inputs help simplify designs operating from 2 V to 5 V rails. Rail-to-rail input behavior is especially useful when the signal range approaches either supply rail, while the high-speed response supports applications requiring rapid threshold decisions. The TS3022ID is identified as a general-purpose dual comparator with push-pull outputs. Its specified supply range is 2 V to 5 V, and the datasheet describes a high-speed response time. The TS3022 family is designed for micropower operation, with supply consumption described as being as low as a few tens of microamperes. The operating temperature range of -40 °C to +125 °C supports use across industrial, automotive, and consumer temperature conditions when the surrounding system satisfies the device's electrical requirements. The rail-to-rail input architecture allows sensing of signals close to the positive or negative supply rails. This can reduce the need for artificial input biasing in low-voltage systems, although input common-mode behavior, output timing, and supply decoupling still require careful validation in the final application. Because the device contains two comparators, applications can use the two channels for independent decisions or for upper and lower thresholds that define a monitoring window. Typical uses include battery-voltage threshold detection, overvoltage and undervoltage indication, signal crossing detection, pulse-width qualification, sensor-level conditioning, and fast logic-level generation. The 8-SOIC package is also convenient for prototypes and through-hole assembly. For battery-powered equipment, the low operating voltage and micropower characteristics can help reduce system energy use, provided the input signals remain within the specified common-mode range. Designers should place supply bypass capacitance close to the device and use the pin descriptions in the manufacturer datasheet when assigning PCB tracks. Input filtering may be required when noisy signals are compared because propagation delay and input offset can cause repeated output transitions. The TS3022ID is therefore most appropriate when a designer needs two fast, low-voltage, rail-to-rail comparator channels in a conventional SOIC footprint.

Запрос цены Контакты
TS321ID - Single 30 V 800 kHz Op Amp | Texas Instruments
TS321ID

TS321ID - Single 30 V 800 kHz Op Amp | Texas Instruments

Texas Instruments TS321ID is a single bipolar operational amplifier rated for 30 V operation, an 800 kHz gain-bandwidth product, and an 8-pin SOIC package. It is intended for cost-sensitive applications where space savings matter, making it a compact general-purpose amplifier for industrial, instrumentation, and signal-conditioning systems. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The TS321 belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and semiconductor. Its basic amplifier functions include voltage amplification, buffering, filtering, summing, and feedback-based control, provided the external feedback network and operating limits are respected. The verified product information identifies a single amplifier circuit, a 30 V maximum operating framework, 800 kHz bandwidth, general-purpose classification, and an 8-pin SOIC package. The bipolar architecture and low-power positioning suit cost-sensitive designs, while the SOIC footprint supports conventional surface-mount assembly. Exact offset, bias-current, noise, slew-rate, common-mode, and output-swing values require confirmation in the manufacturer datasheet before final circuit sign-off. TS321ID is useful as a general-purpose amplifier in low- and moderate-bandwidth analog paths. Its verified 800 kHz bandwidth makes it relevant to signal conditioning where the required closed-loop bandwidth is well below that level. The single-amplifier configuration can simplify designs that need one amplifier rather than a dual package, particularly in sensor interfaces, control loops, audio preamplification, and industrial measurement circuits. The principal design consideration is preserving signal headroom and stability. An 8-pin SOIC package requires adequate PCB spacing, controlled grounding, and decoupling close to the power pins. Feedback resistors, compensation components, and input or output loading determine the actual usable bandwidth and must be evaluated against the application. Because verified operating details beyond the supplied values are incomplete, engineers should consult the TS321 manufacturer datasheet before choosing component values. This page combines verified manufacturer and distributor information, structured technical context, sourcing guidance, and engineering notes. It also clearly identifies unavailable electrical parameters rather than presenting guessed values, helping engineers move from part selection to a validated TS321ID design with fewer sourcing and specification ambiguities.

Запрос цены Контакты
TS321IDR - Single 30 V 800 kHz Op Amp | Texas Instruments (Tape & Reel)
TS321IDR

TS321IDR - Single 30 V 800 kHz Op Amp | Texas Instruments (Tape & Reel)

Texas Instruments TS321IDR is a single bipolar operational amplifier rated for 30 V operation, an 800 kHz gain-bandwidth product, and an 8-pin SOIC package. It is intended for cost-sensitive applications where space savings matter, making it a compact general-purpose amplifier for industrial, instrumentation, and signal-conditioning systems. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The TS321 belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and semiconductor. Its basic amplifier functions include voltage amplification, buffering, filtering, summing, and feedback-based control, provided the external feedback network and operating limits are respected. The verified product information identifies a single amplifier circuit, a 30 V maximum operating framework, 800 kHz bandwidth, general-purpose classification, and an 8-pin SOIC package. The bipolar architecture and low-power positioning suit cost-sensitive designs, while the SOIC footprint supports conventional surface-mount assembly. Exact offset, bias-current, noise, slew-rate, common-mode, and output-swing values require confirmation in the manufacturer datasheet before final circuit sign-off. TS321IDR is useful as a general-purpose amplifier in low- and moderate-bandwidth analog paths. Its verified 800 kHz bandwidth makes it relevant to signal conditioning where the required closed-loop bandwidth is well below that level. The single-amplifier configuration can simplify designs that need one amplifier rather than a dual package, particularly in sensor interfaces, control loops, audio preamplification, and industrial measurement circuits. The principal design consideration is preserving signal headroom and stability. An 8-pin SOIC package requires adequate PCB spacing, controlled grounding, and decoupling close to the power pins. Feedback resistors, compensation components, and input or output loading determine the actual usable bandwidth and must be evaluated against the application. Because verified operating details beyond the supplied values are incomplete, engineers should consult the TS321 manufacturer datasheet before choosing component values. This page combines verified manufacturer and distributor information, structured technical context, sourcing guidance, and engineering notes. It also clearly identifies unavailable electrical parameters rather than presenting guessed values, helping engineers move from part selection to a validated TS321IDR design with fewer sourcing and specification ambiguities.

Запрос цены Контакты
TS321IDT - 30V Single 800kHz Op Amp | STMicroelectronics
TS321IDT

TS321IDT - 30V Single 800kHz Op Amp | STMicroelectronics

The STMicroelectronics TS321IDT is a single bipolar operational amplifier with an 800 kHz gain-bandwidth product, a 30 V total supply rating, and an 8-pin SOIC package. Designed for cost-sensitive applications where space efficiency matters, the TS321IDT provides a practical general-purpose amplification stage for industrial control, instrumentation, sensor interfaces, and low-frequency signal-conditioning circuits. An operational amplifier is an active analog component that uses high-gain differential feedback to amplify the difference between two input voltages. Within the product hierarchy, the TS321IDT is a general-purpose operational amplifier, a bipolar linear amplifier, and a member of the broader analog IC and semiconductor families. Its role is to increase signal amplitude while maintaining the closed-loop behavior established by external resistors or feedback networks. Key characteristics include the single-amplifier configuration, 800 kHz bandwidth, and 30 V maximum supply voltage. The manufacturer describes the device as a bipolar operational amplifier intended for compact, cost-sensitive designs. Its performance approach is intended to match or better selected industry-standard devices such as the LM358A and LM324 families, providing a familiar general-purpose solution without requiring a high-speed or precision-amplifier architecture. The TS321IDT operates from a dual supply extending to plus or minus 15 V, equivalent to a maximum total supply of 30 V. Its single-amplifier organization makes it appropriate when the PCB does not justify a dual or quad amplifier. Because it is a bipolar part rather than a CMOS amplifier, engineers should pay particular attention to input bias current, offset behavior, common-mode range, and output-swing limits during precision signal-chain design. Typical uses include buffering sensor outputs, amplifying low-level analog signals, active filtering, gain stages in measurement systems, and general industrial signal conditioning. It is particularly useful in compact equipment where an 8-pin SOIC footprint provides more mechanical flexibility than a small-outline package while maintaining low cost and straightforward PCB assembly. When laying out a TS321IDT circuit, place input, output, and decoupling connections according to the manufacturer pin-description table and keep feedback resistors close to the amplifier where practical. Confirm the required input common-mode voltage and output swing against the actual signal range. Stable operation also depends on suitable output loading and the compensation or feedback network selected for the intended gain. This page combines manufacturer and distributor information with an obsolete-lifecycle assessment, same-footprint alternatives, application guidance, and design considerations. It helps engineers distinguish a genuine circuit-compatible replacement from a merely similar single amplifier before committing a redesign to an active device.

Запрос цены Контакты
TS321ILT - 800kHz Low-Power Op Amp | STMicroelectronics
TS321ILT

TS321ILT - 800kHz Low-Power Op Amp | STMicroelectronics

STMicroelectronics TS321ILT is a single low-power bipolar operational amplifier with an 800 kHz gain-bandwidth product, 0.4 V/µs slew rate, and operation from 3 V to 30 V, housed in a compact SOT-23-5 package. The device supports output swing from approximately -1.5 V to +1.5 V under its stated operating conditions and is designed for general-purpose signal amplification where low cost, compactness, and low power consumption are important. An operational amplifier, or op amp, is a voltage-controlled differential amplifier that uses external feedback to set its gain and filtering behavior. The TS321 belongs to the low-power operational-amplifier hierarchy, combining common-mode input range, open-loop gain, output-drive capability, and stability in a small integrated circuit. Its bipolar implementation is intended for cost-sensitive applications where the SOT-23-5 package can save board space compared with larger SOIC implementations. The TS321ILT provides an 800 kHz gain-bandwidth product and 0.4 V/µs slew rate, making it appropriate for low-frequency audio, sensor conditioning, current monitoring, and general signal-shaping circuits. Its single-amplifier configuration reduces component count in applications that do not require a dual or quad amplifier. The 3 V to 30 V supply range also permits operation from conventional 5 V, 12 V, and 24 V industrial rails when the signal levels and dissipation permit. STMicroelectronics describes the TS321 as a bipolar low-power operational amplifier intended for space-constrained, cost-sensitive designs. The device is specified to match or improve relevant performance characteristics of established industry-standard amplifiers such as LM358A and LM324 families. Because it is a single amplifier, systems requiring several independent signal channels must use multiple TS321ILT devices rather than one dual or quad package. Typical uses include low-level sensor amplification, industrial control signal conditioning, audio preamplification, battery-powered instrumentation, and general analog buffers. In a practical inverting amplifier, the closed-loop bandwidth is determined by the feedback network as well as the 800 kHz gain-bandwidth product. Stable resistor and capacitor values should be selected with operating frequency, output swing, capacitive loading, and supply voltage taken into account. The main design consideration is to avoid treating the approximate output-swing limits as full rail-to-rail operation. Input and output signals must remain inside the specified common-mode and output ranges. Designers should also check the stability behavior of the chosen feedback topology under expected source capacitance and load capacitance because those board-level conditions influence practical amplifier performance. This product page combines the TS321ILT electrical specifications, package information, application guidance, and same-footprint replacement comparisons. It also provides practical guidance on feedback design, common-mode limits, supply selection, and PCB implementation so engineers can assess the amplifier before placing it in a new analog circuit.

Запрос цены Контакты
TS331ILT - 1.6V-5V Micropower Open-Drain Comparator | STMicroelectronics
TS331ILT

TS331ILT - 1.6V-5V Micropower Open-Drain Comparator | STMicroelectronics

STMicroelectronics TS331ILT is a single-channel, micropower, low-voltage comparator with open-drain output, rail-to-rail input capability, and a 1.6V to 5V supply range. The device is packaged in the compact SOT-23-5 surface-mount package and is intended for portable, battery-powered, sensor, and low-voltage signal-conditioning systems. Its typical supply current is as low as 20 uA, making it suitable for designs where comparator power consumption affects battery life. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input exceeds the other by more than its input-offset threshold. The TS331 belongs to the comparator, analog IC, and low-voltage power-management hierarchy. It uses an open-drain output, allowing the output to be pulled up externally when a wired-OR arrangement, level translation, or direct digital-interface connection is required. The TS331ILT operates from 1.6V to 5V and provides rail-to-rail inputs, allowing signals to be compared close to the supply rails without relying on a conventional mid-supply input range. The listed specifications include 26 uA supply current, 1 nA input bias current, 40 nA input offset current, 5 mV input offset voltage, 4.5 uV/°C temperature drift, 720 ns propagation delay, and 79 dB channel-to-channel rejection. These characteristics balance response speed, low power, and precision for compact embedded systems. The open-drain output is useful when several signals must be combined, but it requires an external pull-up resistor in most applications. The SOT-23-5 footprint supports dense PCB layouts, although correct input polarity and output-pull-up placement are important. The comparator can be used for voltage-threshold detection, battery monitoring, sensor signal conditioning, overvoltage detection, and portable equipment. Designers should select pull-up voltage and resistor values carefully, account for the open-drain output's rise time, and verify operation across the full temperature range. The TS331 family's low supply current and rail-to-rail inputs are particularly advantageous in 1.8V, 2.5V, and 3.3V systems where the signal range may span the full supply voltage. This product page combines the manufacturer specifications, package information, practical design guidance, and drop-in replacement considerations for engineers evaluating the TS331ILT in low-voltage comparator applications.

Запрос цены Контакты
TS339CD - Micropower Quad CMOS Comparator | STMicroelectronics
TS339CD

TS339CD - Micropower Quad CMOS Comparator | STMicroelectronics

STMicroelectronics TS339CD is a micropower quad CMOS voltage comparator containing four independent general-purpose comparators in a 14-pin SOIC package. Each comparator features open-drain CMOS outputs, extremely low input bias current, and a typical supply current consumption of 9 µA per comparator. The device provides a typical response time of 1.5 µs for a 5 mV input overdrive. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic result indicating which input is higher. The TS339 belongs to the broader comparator hierarchy, where a quad comparator integrates four independent analog-to-digital decision channels. Its CMOS construction combines low power consumption with high input impedance, making it suitable for battery-operated sensing, control, and signal-conditioning systems. The four channels can compare sensor outputs with adjustable references or supervise multiple operating conditions. Key characteristics include extremely low input bias current, a typical input offset current of 1 pA, and a typical input impedance of 10^12 ohms. The open-drain outputs allow the device to interface with pull-up resistors, level shifters, wired logic buses, and mixed-voltage systems. A typical response time of 1.5 µs for 5 mV overdrive supports applications requiring fast threshold decisions without the higher supply consumption commonly associated with bipolar comparator families. The TS339 is also described as pin-to-pin and functionally compatible with the bipolar LM339 family. This compatibility makes the open-drain architecture particularly useful when an existing board uses pull-up-based logic. Each comparator can independently monitor a sensor threshold, supply rail, window comparator, or control signal. Because the outputs are open drain, multiple device outputs can share a common pull-up when the system designer confirms that the combined sink-current and timing requirements remain acceptable. Typical uses include low-power battery monitoring, industrial threshold detection, sensor interface conditioning, overvoltage protection, and embedded control systems. The 14-pin SOIC package supports conventional surface-mount assembly and provides one channel per comparator, making channel assignment straightforward in multi-parameter monitoring systems. When laying out the circuit, route the comparator inputs away from switching nodes and place the open-drain pull-up resistors close to the output pins. Confirm input common-mode limits, supply-voltage range, output sink-current capability, and the effect of external pull-up resistance before using the device in a new design. This page combines the manufacturer's functional description, package information, comparator performance characteristics, verified cross-reference candidates, and practical design guidance to support component selection, schematic review, and PCB implementation.

Запрос цены Контакты
TS339CN - 16V Micropower Quad CMOS Comparator | STMicroelectronics
TS339CN

TS339CN - 16V Micropower Quad CMOS Comparator | STMicroelectronics

STMicroelectronics TS339CN is a micropower quad CMOS voltage comparator with four independent comparison channels, open-drain outputs, and a 14-pin through-hole DIP package. The device operates from a single supply up to 16 V, consumes 9 uA typical per comparator, provides 1 pA typical input offset current, and has input impedance of 10^12 ohms typical. These characteristics make it suitable for low-power sensing, threshold detection, and analog signal conditioning. A voltage comparator is an integrated circuit that compares two input voltages and changes its output state according to their relative polarity. The TS339 belongs to the comparator hierarchy, where a comparator is a type of analog integrated circuit and signal-conditioning semiconductor. Its four channels provide flexible logic-level sensing, while the open-drain outputs allow wired connections or external pull-up networks when a push-pull output is not required. The principal benefits of the TS339CN are its low 9 uA typical supply current per comparator, extremely low 1 pA typical input offset current, and high 10^12 ohm typical input impedance. These characteristics reduce loading on high-impedance sensors and support battery-operated or low-leakage measurement systems. The open-drain architecture also supports wired-AND behavior, provided suitable pull-up resistors and an appropriate supply voltage are used. The TS339CN is designed around a CMOS input stage and four independent comparator channels. Its response time is 1.5 us typical for a 5 mV overdrive condition, making it suitable for many threshold and control functions where microsecond-scale decisions are sufficient. The manufacturer also identifies the device as pin-to-pin and functionally compatible with the bipolar LM339, which can simplify qualification of an existing comparator-based design. Typical uses include battery-powered sensor interfaces, low-voltage monitoring circuits, threshold detection, window comparators formed from pairs of channels, and general control logic. Because the outputs are open-drain, an application must include pull-up resistors whenever a valid high output level is required. The four-channel architecture also allows multiple independent measurements from a single IC. For a new through-hole design, allow adequate clearance around the 14-pin DIP footprint and route sensitive input traces away from switching nodes and output pull-up networks. Input common-mode range, output saturation levels, supply current, and output timing should be checked against the manufacturer datasheet for the intended supply voltage and temperature conditions. This page organizes the key TS339CN specifications, comparison information, practical design notes, and verified sourcing references. It also highlights the device's open-drain output architecture, low-power operation, and LM339 compatibility considerations for engineers evaluating PCB and firmware changes.

Запрос цены Контакты