Интегральные схемы

DG485DJ

DG485DJ - 8-Channel SPST Analog Switch Array | Vishay

Vishay Intertechnology DG485DJ is an octal analog switch array containing eight single-pole, single-throw switches connected to a common output. The device supports analog multiplexing in serial-control systems, with any combination of the eight switches able to close simultaneously. It is specified in a 16-DIP package with an 85 ohm maximum on-resistance, 55 ohm typical on-resistance, and a typical turn-on time of 170 ns. An analog switch array is a group of electronically controlled switches used to route analog signals under digital control. The DG485DJ belongs to the analog switch IC hierarchy, where individual SPST switches share a common output and can be addressed through a serial interface. This arrangement reduces the number of external connections required when several sources must be selected, particularly in data-acquisition, audio-routing, test, and instrumentation systems. The DG485DJ provides a rail-to-rail analog input range, TTL- and CMOS-compatible control signals, low signal distortion, and the ability to chain devices. Its low on-resistance helps limit signal attenuation when a switch is closed, while the 170 ns typical turn-on time supports higher-speed routing than slower electromechanical switches. Low-power operation further suits systems in which multiple switched paths must be present without continuously consuming substantial power. Typical uses include eight-channel analog multiplexing, audio signal routing, data acquisition, process-control interfaces, and automated test systems. In a multiplexer arrangement, the DG485DJ selects one or more of eight input sources for connection to the common output. Designers should account for signal amplitude, source impedance, logic levels, switching transients, and the bandwidth limitations associated with the selected on-resistance when planning signal paths. The 16-DIP package favors through-hole prototyping, legacy control systems, and applications that value straightforward inspection or rework. Layout guidance should keep sensitive analog traces away from high-current switching paths, place suitable bypassing near the supply pins, and follow the manufacturer's pin-description table when assigning control and signal connections. This page consolidates the device architecture, verified electrical characteristics, application guidance, package information, and engineering considerations needed to evaluate the DG485DJ for an eight-channel multiplexing or routing design.

Запрос цены Контакты

DLP4500

DLP4500 - 0.45 WXGA DMD | Texas Instruments | Spatial Light Modulator

The DLP4500 from Texas Instruments is a digitally controlled MOEMS (micro-opto-electromechanical system) spatial light modulator (SLM) featuring a 0.45-inch (11.43 mm) diagonal micromirror array of aluminum, micrometer-sized mirrors. With a 7.6-µm micromirror pitch and ±12° micromirror tilt angle, it delivers high-resolution pattern steering for visible light applications. The device is designed to work with the DLPC350 controller, which coordinates mirror reset pulses and image data loading. A digital micromirror device (DMD) is an array of microscopic mirrors that reflect light to create patterns or images. Each mirror represents one pixel and can be tilted between two states to modulate light. DMDs are the core of DLP projection technology and are used in spatial light modulation for structured light, 3D scanning, and optical patterning. The DLP4500 is a WXGA (912 × 1140) array, offering high resolution in a compact form factor. Key features include a 912 × 1140 micromirror array, 7.6-µm mirror pitch, ±12° tilt angle, and support for a 30-bit parallel RGB interface for image data transfers. The device operates with a DLPC350 controller and requires proper generation of PWRGOOD and POSENSE inputs for reliable operation. The DLP4500 is available in a 98-pin LCCC package (20.7 × 9.1 mm) and is designed for visible light applications. The DLP4500 uses a MEMS (micro-electromechanical systems) architecture where each micromirror is electrostatically actuated. The mirrors are arranged in a 912 × 1140 array with a uniform band of border micromirrors that are not user-addressable. The device supports high-speed pattern rates, making it suitable for applications requiring fast light modulation. The DLPC350 controller generates internal mirror reset pulses, ensuring precise timing. Typical applications include 3D scanning and measurement, structured light for machine vision, augmented reality, and optical patterning. The DLP4500 is also used in medical imaging and spectroscopy. Its high resolution and fast switching make it ideal for industrial and scientific applications where precise light control is essential. When designing with the DLP4500, ensure proper thermal management and signal integrity. The device requires a clean power supply and careful PCB layout to minimize noise. The DLPC350 controller must be configured correctly to achieve optimal performance.

Запрос цены Контакты

DLPC3479CZEZ

DLPC3479CZEZ - DLP Controller for DLP4710LC | Texas Instruments

The Texas Instruments DLPC3479CZEZ is a DLP display and light controller for the DLP4710LC (0.47-inch 1080p) digital micromirror device (DMD), supplied in a 201-ball NFBGA (ZEZ) package measuring 13 mm x 13 mm. It provides high-speed, precision interface and steering between system electronics and the DMD for video display and light control applications, including 2xDLPC3479 dual-controller configurations. The device operates over the industrial -30C to +85C temperature range and is qualified for display and projection designs requiring pixel-accurate DMD control. A DLP controller (Digital Light Projection controller) is a mixed-signal ASIC that orchestrates illumination timing, micromirror bit-planes, video processing, and host command interface for a DLP digital micromirror device (DMD). DLP controllers sit at the apex of the DLP chipset hierarchy (DLP controller -> DMD driver -> DMD -> optical engine -> display system), and are required to bring up, sequence, and continuously refresh the MEMS micromirror array while maintaining pixel-level color and brightness accuracy across frame rates. Key features include support for the DLP4710LC 0.47-inch 1080p DMD, an integrated ARM Cortex host-side interface, integrated illumination driver interface, and high-speed DMD data path with deterministic latency. The device supports video display and light steering modes commonly used in industrial projection, 3D printing, 3D machine vision, and spectroscopy, while the 201-ball NFBGA provides the routing density required for the parallel DMD data bus at full HD resolution. The DLPC3479 uses a programmable microcontroller subsystem to manage DMD load, micromirror reset sequences, LED/laser light source timing, and host command protocol over I2C or SPI. The 2xDLPC3479 dual-controller topology (referenced in the TI datasheet) supports higher resolution or higher brightness configurations by pairing two controllers with a single DMD, enabling synchronized bit-plane generation for light control applications such as structured light, mask-less lithography, and exposure systems. Typical applications include 1080p portable projectors, industrial inspection cameras, structured-light 3D scanners, 3D printers, head-up displays, and medical imaging systems. The DLP4710LC chipset is also widely used in AR glasses, near-eye displays, and head-mounted displays where the small 0.47-inch panel format and DLP's high fill factor enable compact optical engines. When designing with this device, ensure the PCB layout follows the TI NFBGA-201 escape pattern and that the DMD high-speed data bus is length-matched per the DLPC3479 datasheet guidelines. The DLPC3479 must be paired with the DLP4710LC DMD; it is not a generic DLP controller and cannot be substituted with DLPC34xx controllers intended for other DMDs without re-validating the full chipset configuration and firmware load. This page synthesizes the TI DLPC3479 datasheet, current DigiKey/Mouser pricing as of 2026-10-07, drop-in alternatives within the DLP4710LC family, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

DLPC6540ZDC

DLPC6540ZDC - 4K UHD DLP Display Controller for DLP471TP DMD | TI

The Texas Instruments DLPC6540ZDC is a DLP display controller for the DLP471TP (0.47-inch 4K UHD) digital micromirror device (DMD), housed in a 201-pin NFBGA (13x13 mm) package. The DLPC6540 controller, working in concert with the DLP471TP DMD and the DLPA3005 power management IC (PMIC), forms a complete 4K UHD display chipset targeting high-resolution and high-brightness systems in a compact optical engine footprint. A DLP display controller is the digital signal-processing and sequencing hub of a TI DLP chipset. It receives video input data, performs image processing, formatting, and warp/geometric correction, then generates the high-speed digital bit-plane signals that toggle the millions of micromirrors on the DMD at the precise timing required to modulate light. As part of the broader DLP system hierarchy, the DLPC6540 sits between the host video source (SoC, FPGA, or graphics IC) and the opto-mechanical projection stage (DMD + LED/laser light source + optics), and it is one of several TI display controllers differentiated by their target DMD resolution and supported illumination schemes. Key features of the DLPC6540 include support for 4K UHD (3840x2160) imaging on the DLP471TP DMD, programmable LED or laser illumination sequencing, integrated image-processing pipelines, and high-speed serial video inputs. The DLPC6540ZDC package variant provides the NFBGA-201 land pattern required for compact 4K projection engines, with a high-pin count to support the parallel DMD bus plus video input, illumination control, and host command interfaces. Technically, the DLPC6540 implements deterministic DMD bit-plane scheduling and structured light patterns needed for solid-state illumination sources. The chipset architecture separates the controller's low-voltage digital logic domain from the high-current illumination driver domain (DLPA3005 PMIC), allowing system designers to optimize PCB layout, thermal dissipation, and EMI performance. Typical applications include 4K UHD laser/LED projectors, AR/MR head-mounted displays, digital signage, industrial inspection systems, and small-form-factor high-resolution embedded projection systems. Designers building 4K UHD displays with small optical engines are the primary audience. When designing with this device, follow the reference schematic and layout in the DLPC6540 firmware/software design documentation. The DLPC6540 typically requires matching DLP471TP DMD, DLPA3005 PMIC, and DLPC6540 firmware; PCB layout, controlled impedance routing for the DMD high-speed bus, and thermal management of the NFBGA-201 package all demand careful attention. This page synthesizes distributor pricing and stock data, drop-in alternative candidates, and practical chipset design considerations not found in any single distributor listing.

Запрос цены Контакты

DM74LS138N

DM74LS138N - 3-to-8 Line Decoder/Demultiplexer, LS-TTL, 16-PDIP | onsemi

The onsemi (formerly Fairchild) DM74LS138N is a 3-to-8 line decoder/demultiplexer built on Schottky-clamped Low-power Schottky (LS) TTL technology, packaged in a 16-pin PDIP through-hole format. The device accepts three binary-weighted address inputs (A, B, C) and provides eight active-LOW mutually exclusive outputs (Y0-Y7), along with three enable inputs (G1, G2A, G2B) that allow cascading or address expansion. According to the manufacturer datasheet, it is designed for high-performance memory-decoding and data-routing applications requiring very short propagation delay times. A decoder/demultiplexer is a combinational logic IC that translates a binary address on its inputs into a single selected output line. In its canonical role, the '138' family member accepts 3 address bits and activates exactly one of 8 outputs, which is why it is commonly referred to as a 1-of-8 decoder. It belongs to the broader hierarchy: decoder/demultiplexer -> combinational logic -> logic IC -> digital IC -> integrated circuit -> semiconductor. Common synonyms include '3-line to 8-line decoder', 'binary-to-octal decoder', and '1-of-8 demultiplexer'. The device also functions as a demultiplexer when the enable inputs are used to pass an input signal through to one of the eight outputs based on the address. Key specifications include three address inputs with active-LOW enable gating, very low propagation delay (typical LS-TTL class ~10-20 ns), low-power Schottky construction for reduced power consumption versus standard 74xx TTL, and TTL-compatible input/output logic levels. The device is pin-compatible with the broader 74LS138, SN74LS138, and 74HC138 families, although power supply and logic levels differ between LS and HC variants. Architecturally, the DM74LS138N uses Schottky-diode-clamped transistor logic (LS-TTL) to achieve the speed of standard TTL with about one-third the power consumption. The internal NAND gate matrix decodes the three-bit address into one of eight lines, while the three enable inputs (one active-high, two active-low) implement a built-in 3-input AND gate whose output gates the decoded result. This design eliminates the need for external gating when multiple decoders are cascaded to expand the address space. Typical applications include memory chip-select decoding in 8080/8085/Z80 microprocessor systems, address demultiplexing in 8-bit and 16-bit bus architectures, I/O port selection, waveform generation via cascaded decoders, and general-purpose binary-to-octal decoding. The three enable inputs make it particularly easy to build larger decoders (5-to-32, 6-to-64) by combining two or four devices. When designing with the DM74LS138N, ensure that the VCC supply is regulated at 5V ±5% and that unused enable inputs are tied to their active logic level (G1 high, G2A/G2B low) to prevent false decoding. Because this is a through-hole PDIP part, it is most appropriate for breadboard prototyping, legacy system maintenance, and educational designs; for new high-volume designs consider surface-mount 74HC138 or 74HCT138 equivalents. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

DP8304BWM

DP8304BWM - 8-Bit Tri-State Bus Transceiver | TI

The Texas Instruments DP8304BWM is an 8-bit tri-state bidirectional bus transceiver packaged in a 20-pin SOP. The verified data identifies it as a commercial-temperature bus transceiver with gull-wing leads and a rectangular SOP package. Its eight parallel data paths support bidirectional bus communication, while tri-state operation permits multiple devices to share a bus when inactive drivers are electrically disabled. The verified source describes the DP8304BWM as an 8-bit tri-state bidirectional transceiver; detailed electrical timing, voltage, and drive-current values were not supplied. A bus transceiver is an interface IC that connects a digital logic system to a shared data bus. Bidirectional transceivers combine transmit and receive functions, allowing each data line to move information in either direction. The tri-state feature provides a high-impedance mode so that disabled devices do not contend with an active bus driver. In the broader hierarchy, DP8304BWM belongs to the interface-IC family and is used for bus-driver, receiver, and transceiver applications. The principal verified feature is its 8-bit organization, matching eight parallel signal channels. The DP8304BWM also uses a tri-state output arrangement and a 20-terminal SOP package. Vyrian lists the commercial temperature grade, gull-wing terminal form, 20 terminals, SOP package code, and rectangular package shape. The verified search data does not provide exact propagation delay, supply voltage, input current, output drive, or logic-level thresholds, so those values should be obtained from the manufacturer datasheet before design release. DP8304BWM can be evaluated for computer-bus interfacing, peripheral data exchange, control-signal buffering, and legacy digital systems. Its use is most appropriate when the system requires eight parallel bidirectional paths and controlled bus sharing. Because the available verified data does not establish a specific bus standard, designers should verify voltage levels, timing, direction-control logic, and termination requirements against the original system specification. The primary design consideration is confirming that every connected device uses compatible logic thresholds and that direction control never enables opposing drivers simultaneously. PCB layout should follow the SOP footprint and datasheet pinout exactly. Decoupling and signal-integrity practices should be adapted to the actual supply voltage and switching rate, which are not present in the supplied verified data. Do not infer a replacement from package similarity alone. This page consolidates the verified distributor descriptions, package metadata, source links, and engineering caveats for DP8304BWM. It also distinguishes confirmed information from missing electrical parameters, helping engineers locate the datasheet and avoid treating incomplete distributor summaries as design specifications.

Запрос цены Контакты

DP8308N

DP8308N 8-Bit Non-Inverting Bus Transceiver | NS | DIP-20

National Semiconductor DP8308N is an 8-bit non-inverting TRI-STATE bidirectional bus transceiver with 8 bits per element, supplied in a 20-PDIP package. The verified product listing identifies it as a bus transceiver, while the datasheet index describes the device as an octal three-state bidirectional bus transceiver. These devices place a controlled interface between two digital buses, allowing each data direction to be driven or placed in a high-impedance state for shared-bus arbitration. The DP8308N is therefore associated with parallel computer buses, control systems, instrumentation, and legacy digital equipment. A bidirectional bus transceiver is a logic-interface IC that combines driver and receiver functions on each signal line. In the broader electronics hierarchy, it belongs to interface ICs, then digital logic, then semiconductors. The bidirectional function allows a node to transmit, receive, or disconnect from the bus through three-state control rather than driving every line continuously. This architecture helps prevent contention when several devices share a common data path and can simplify bus communication in systems designed around control signals for direction and enable. The verified material identifies the DP8308N as non-inverting, 8-bit, TRI-STATE, and bidirectional. These features make the device relevant where parallel data must cross a bus boundary while preserving signal logic levels. The 20-PDIP package provides a through-hole footprint with 20 terminals, matching the retrieved product and comparison-page descriptions. Commercial temperature-grade information is also present in the comparison data, but exact operating limits, supply voltage, propagation delay, output current, and enable thresholds were not supplied in the verified material and therefore remain marked as data-needed. Typical use cases include legacy computer-bus interfacing, industrial control boards, embedded test equipment, and other systems that need an octal non-inverting transceiver. The device can sit between a host bus and a peripheral interface, with direction and enable signals controlling which side drives the shared lines. Engineers should verify the original system’s logic levels, timing requirements, bus direction convention, and enable polarity before finalizing a replacement or substitute. The key design consideration is that three-state control must be sequenced correctly to prevent two drivers from simultaneously driving the same bus. Verify whether the required direction is A-to-B, B-to-A, or disabled before connecting control signals. Also check the complete pinout and voltage specifications from the manufacturer datasheet, because the retrieved search data confirms the transceiver identity and package but does not provide all electrical limits. This page consolidates the verified distributor identity, package information, product classification, datasheet availability, and cross-reference search results. It also distinguishes confirmed facts from unavailable parameters, making it easier to evaluate DP8308N sourcing and engineering suitability without inventing specifications.

Запрос цены Контакты

DP83222V

DP83222V - CYCLONE Twisted Pair FDDI Stream Cipher | TI/NSC

The DP83222V is a CYCLONE Twisted Pair FDDI Stream Cipher Scrambler IC from National Semiconductor (Texas Instruments heritage), housed in a 28-pin PLCC (11.43x11.43 mm) package. Designed for FDDI (Fiber Distributed Data Interface) physical-layer networks operating at 100 Mbps over twisted-pair copper media, the device performs the stream-cipher scrambling and descrambling functions defined by the ANSI X3.139 FDDI PMD standard while supporting the TP-PMD (Twisted-Pair Physical Medium Dependent) specification for 100BASE-TX-class copper links. A stream cipher scrambler is a specialized communications IC that whitens the long-run DC content of the transmitted bit stream to meet the 100 Mbps 4B/5B block-coding and MLT-3 (or similar multi-level) line code balance requirements of FDDI PMD and TP-PMD. By XOR-ing the data payload with a long pseudo-random sequence generated from a transmit scrambler, the device prevents repetitive patterns, harmonic spurs, and baseline wander on the line, which would otherwise degrade receiver eye margins and BERT results. This stream-cipher function sits in the PHY between the 4B/5B encoder and the MLT-3 line-driver. Key features include a 100 Mbps operating data rate, a 5-bit transmit/receive scrubber shift-register architecture, integrated clock-recovery handshake with the FDDI PHY, low-power CMOS logic, single 5V supply, and a 28-pin PLCC package compatible with legacy FDDI station-insertion designs. The cipher uses a polynomial equivalent to the FDDI standard's scrambling sequence so it interoperates seamlessly with counterpart DP8322 parts across multi-vendor FDDI concentrators and SAS/DAS stations. Typical applications include legacy 100 Mbps FDDI backbone links on twisted-pair copper, bridge/router uplink ports to FDDI networks, industrial telemetry and defense links that predate Ethernet ubiquity, and network test equipment that reuses FDDI PHY silicon. Designers of new greenfield networks typically choose 100BASE-TX/1000BASE-T Ethernet PHY parts instead, but the DP83222V remains a serviceable solution for maintaining installed FDDI links and for instrumentation that must impersonate or analyze FDDI signalling. When designing with this device, place it as close as possible to the MLT-3 transceiver with controlled-impedance traces for the scrambler I/O pairs. Bypass VCC with a 0.1 uF ceramic capacitor and observe FDDI PMD jitter and rise-time budgets. Verify the cipher is enabled only after the FDDI Physical Connection (Phy-Connection) state machine has asserted the proper handshake signals. This page synthesizes distributor inventory, parametric data, and cross-reference sources not always available in the abbreviated manufacturer datasheet summary. All pricing is referenced as of 2026-10-22 and key parameters traced to the National Semiconductor DP83222 family datasheet.

Запрос цены Контакты

DP83223AV

DP83223AV - Twister MLT-3 Network Transceiver | National

The National Semiconductor DP83223AV is a Twister high-speed networking transceiver integrated circuit designed to transmit and receive three-level MLT-3 encoded data streams. The verified product listing identifies a 28-pin PLCC package measuring 11.43 mm by 11.43 mm. Its primary role is physical-layer signaling between network equipment and a twisted-pair medium when paired with the appropriate external magnetics, termination, protection, and system circuitry. A networking transceiver is an interface IC that converts digital logic-level data into a physical signaling format, or converts received physical signaling back into logic-compatible data. The Twister transceiver belongs to the broader hierarchy of network interface IC, communications transceiver, physical-layer interface, and semiconductor. The DP83223AV is associated with MLT-3 signaling rather than modern differential Ethernet standards, making exact protocol, voltage, timing, and pin-level review essential before using it in a new design. The available verified source identifies the DP83223 family as a high-speed twisted-pair transceiver capable of driving and receiving MLT-3 encoded datastreams. It also identifies DP83223AV as a 28-pin PLCC device. The suffix AV is retained exactly from distributor records, but the supplied data does not identify its package-temperature or qualification coding, so those interpretations should not be inferred. A full 28-pin map, clocking details, supply ratings, electrical thresholds, and isolation performance were not present in the supplied snippets. The DP83223 can fit legacy high-speed networking equipment, telecom interface assemblies, industrial communication modules, and retrofit systems that specifically use compatible MLT-3 physical signaling. Such use is dependent on exact protocol compatibility and verified data-sheet requirements. Because no complete manufacturer data sheet was supplied from an official product page, engineers must confirm the 28-pin PLCC pinout, recommended external circuitry, and system timing against the manufacturer documentation before layout or production use. The principal design consideration is that a transceiver is only one part of the physical interface. Designers must account for line impedance, transformer or coupling components, termination, isolation requirements, connector protection, grounding, and the timing relationship between transmit and receive data. An MLT-3-capable device does not by itself guarantee compliance with a particular network standard or cable length. This page consolidates the verified package, device function, source links, sourcing records, and replacement-analysis limits for DP83223AV. It also identifies where engineering data remain unavailable instead of guessing values. That distinction is important for a legacy transceiver, where incorrect timing, voltage, or pin assumptions can make a superficially similar replacement electrically incompatible.

Запрос цены Контакты

DP83223V

DP83223V - 100Mbps MLT-3 Network Transceiver | Texas Instruments

The Texas Instruments DP83223V is a TWISTER high-speed networking transceiver integrated circuit for one 10 Mbps or 100 Mbps channel, housed in a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. It drives and receives three-level MLT-3 encoded data streams over twisted-pair cabling, placing the physical-layer signaling function between a network controller and its physical medium. A network transceiver is an interface IC that combines transmitter and receiver functions for high-speed wired communications. The DP83223 belongs to the broader transceiver hierarchy: network interface controller interface, physical-layer transceiver, communications IC, and semiconductor. Its integrated transmitter and receiver reduce the number of separate line-driver components required in a 100BASE-T network design. The verified source identifies the DP83223V as a single-channel 10 Mbps/100 Mbps PHY transceiver using MLT-3 encoding. It also identifies a 28-pin PLCC package and 28 pins. Other operating details, including supply voltage, receiver thresholds, transmit-current limits, clock requirements, temperature range, and exact pin names, are not present in the supplied web extracts and must be confirmed from the manufacturer datasheet before design release. Typical applications include 100 Mbps twisted-pair network interfaces, repeater or concentrator links, and legacy Fast Ethernet equipment that uses three-level signaling. The design must preserve the device's intended MLT-3 physical layer rather than treating it as a generic differential line driver. Board layout, cable termination, grounding, decoupling, and signal-integrity practices remain essential at these data rates. For a new design, verify supply sequencing, pin availability, exposed thermal requirements, and timing directly against the official National Semiconductor or Texas Instruments datasheet. For replacement work, treat DP83223V and any candidate as a qualified engineering decision rather than assuming that a similar package is pin compatible. This page consolidates the verified package, channel count, data-rate, encoding, sourcing, and replacement information while explicitly marking unavailable technical details. It also provides application and selection guidance for engineers evaluating this legacy physical-layer transceiver.

Запрос цены Контакты

DP83223V-1

DP83223V-1 - 100 Mbps Ethernet Transceiver | Texas Instruments

The National Semiconductor DP83223V-1 is a single-port Ethernet TX/RX integrated circuit operating from a 5 V supply at 10 Mbps or 100 Mbps in a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. It is identified as a Twister high-speed networking transceiver and belongs to the interface IC hierarchy used to connect twisted-pair network equipment. An Ethernet physical-layer transceiver converts logical data into signals suitable for a network cable and converts returning signals into data for the associated media-access controller. The DP83223V family supports 10 Mbps and 100 Mbps operation, according to the verified distributor specifications. Its single-port architecture serves legacy Fast Ethernet equipment rather than gigabit networks, so PHY function, cable topology, and controller support must be checked before modern system integration. The verified listings identify the device as an Ethernet transceiver with one port, a 5 V supply, and a 100 Mbps maximum listed data rate. The target ordering code DP83223V-1 is listed by DigiKey through Rochester Electronics. The base DP83223V is also listed by DigiKey in a 28-pin PLCC package, providing a useful package reference for design review. Detailed electrical limits, termination requirements, transmit-drive strength, receiver thresholds, temperature range, and exact pin names were not included in the supplied source data and therefore are not inferred here. DP83223V can be evaluated in legacy 10/100-Mbps endpoint, network-interface-card, hub-interface, switch-interface, and industrial-retrofit designs when the surrounding controller and magnetics are compatible with the original Twister architecture. Designers should not substitute it for a gigabit PHY because the verified maximum data rate is 100 Mbps. Likewise, an SOHO or industrial controller must support the same line coding, signaling, isolation, and termination arrangement before the transceiver is selected. The principal design consideration is that a transceiver is only one element of an Ethernet physical layer. The line interface also depends on transformer or magnetics, termination network, connector, controlled-impedance printed circuit board, grounding, and electromagnetic-compatibility design. Follow the manufacturer datasheet for pin connections and application circuitry. Because the exact schematic and pin table were not supplied, validate the complete interface against the current manufacturer documentation rather than relying on distributor summaries. This page consolidates verified distributor identification, sourcing links, package information, and engineering-selection guidance. It does not invent missing timing, electrical, compliance, lifecycle, or pricing values; those fields remain explicitly unresolved where the supplied evidence is insufficient. That distinction is especially important for an older networking transceiver, where exact revision behavior and sourcing status can determine whether a legacy design remains electrically and commercially reproducible.

Запрос цены Контакты

DP83223VB

DP83223VB - High-Speed Twisted-Pair Transceiver | National Semiconductor

The National Semiconductor DP83223VB is a high-speed twisted-pair networking transceiver built for three-level MLT-3 encoded data-stream transmission and reception, supplied in a 28-pin PLCC package. The verified product listing identifies the device as an Ethernet transceiver, while the DP83223 family description identifies it as a TWISTER high-speed networking transceiver. Its core function is to interface digital communications equipment with a physical transmission medium, supporting network-infrastructure designs that require dedicated transmit and receive signal handling. The package and electrical details available from the supplied sources are limited, so the complete pin map and several operating parameters require confirmation from the manufacturer datasheet before layout or replacement work. What is a twisted-pair transceiver? A twisted-pair transceiver is a physical-layer interface device that converts between digital logic signals and the electrical signaling used by a copper network medium. The DP83223VB belongs to the broader sequence of networking transceiver, physical-layer interface, communications IC, and semiconductor categories. Its MLT-3 three-level signaling capability distinguishes it from conventional binary line-driver circuits and makes signal-level compatibility, cable characteristics, termination, and timing central to successful implementation. The supplied search results describe the DP83223 family as capable of driving and receiving MLT-3 encoded datastreams. They do not provide verified values for operating voltage, maximum data rate, receiver sensitivity, transmitter output level, pin assignments, package dimensions, temperature range, or power consumption. Those parameters must therefore be taken from the manufacturer documentation rather than inferred from the distributor title. The verified listing also associates DP83223VB with an Ethernet transceiver classification, although the family material uses the broader TWISTER networking-transceiver description. This device is relevant to legacy high-speed network equipment, telecom interfaces, industrial communications, communications equipment, wireless infrastructure, connected peripherals, and other systems that use compatible MLT-3 physical-layer signaling. Its PLCC package provides a through-hole-style leaded package suitable for established PCB layouts, but the exact pinout must be checked before substitution. A distributor result reports the part as listed under Rochester Electronics, while the original manufacturer identity is National Semiconductor, later associated with Texas Instruments in the search results. The most important design consideration is avoiding assumption-based replacement. Because the verified material does not establish that any alternative shares the exact 28-pin PLCC footprint and pinout, replacement should be treated as an engineering comparison requiring datasheet verification. Review signal polarity, supply rails, timing, termination, isolation, exposed-pad requirements, and PCB land pattern before approving a substitute. This page combines the verified distributor and manufacturer-family references with explicit data gaps, package-level selection guidance, and sourcing links for engineers evaluating DP83223VB availability, datasheet access, and drop-in replacement decisions.

Запрос цены Контакты

DP83223VX

DP83223VX - 5V Twister Transceiver | Texas Instruments

The Texas Instruments DP83223VX is a 5 V TWISTER high-speed networking transceiver with one transceiver channel in a 28-pin PLCC package measuring 11.51 mm by 11.51 mm. The device is intended for data communication over shielded or unshielded twisted-pair cabling and performs the physical-layer functions required to connect digital network equipment to a twisted-pair medium. Its verified supply range is 4.75 V to 5.25 V. A network transceiver is an interface IC that converts logic-level signals into physical-layer signals suitable for a wired network and converts received signals back into usable digital data. In the hierarchy, the DP83223VX is a network interface transceiver, a communications interface IC, and a semiconductor. TWISTER describes the physical-layer signal-processing approach used for differential twisted-pair networking rather than a modern two-wire interface standard. The verified information identifies a transceiver configuration, a 4.75 V to 5.25 V operating supply, and a 28-PLCC J-lead package. Distributor listings classify the part as a driver, receiver, and transceiver, while a technical listing describes it as a high-speed physical-layer device for shielded or unshielded twisted-pair cabling. Detailed data rates, driver and receiver counts, cable reach, termination requirements, and electrical timing limits were not supplied in the verified data and must be confirmed from the manufacturer datasheet before design release. The PLCC package provides a through-hole-style surface-mount form factor with J-shaped leads and a compact 11.51 mm by 11.51 mm body. Its legacy package and interface function make careful footprint verification important when comparing it with modern Ethernet devices. Board layout must preserve the manufacturer's recommended network-line separation, component spacing, grounding, and termination arrangement; the available search excerpts do not provide enough detail to specify those values safely. Potential uses include legacy high-speed network interface equipment, industrial data links, embedded communications controllers, and telecommunications equipment using compatible twisted-pair signaling. The device should be selected only after confirming the protocol, signaling rate, cable type, connector, isolation requirements, and exact pinout against the authoritative datasheet. A modern PHY or Ethernet transceiver may offer different compliance, topology, and supply characteristics and therefore is not automatically interchangeable. For a new layout, do not infer pin assignments from the distributor package title. Obtain the DP83223 datasheet, compare every power, ground, driver, receiver, enable, and network-line connection, and validate the assembled channel with the intended cable and system load. This page synthesizes the supplied manufacturer-linked search results, distributor availability references, package information, and sourcing guidance; missing electrical values are deliberately not guessed.

Запрос цены Контакты

DP83257VF

DP83257VF - FDDI Physical Layer Controller | Texas Instruments

The Texas Instruments DP83257VF is a PLAYERa+ FDDI physical-layer controller with a 160-pin QFP package. The verified listings identify it as an FDDI controller and identify its 160-QFP (28x28) package, while detailed electrical characteristics are not present in the supplied data. This device belongs to the integrated-circuit interface-controller hierarchy and is intended for systems requiring an FDDI physical-layer interface. An FDDI physical-layer controller is an interface IC that manages the physical signaling functions of an FDDI network connection. FDDI, or Fiber Distributed Data Interface, is a local-area networking technology whose physical layer handles signal transmission and reception over fiber or compatible physical media. The controller therefore sits between network-system logic and the physical medium, while higher-level software and protocol functions remain outside the device’s stated role. The most important verified identifiers are the DP83257VF MPN, National Semiconductor legacy attribution, Texas Instruments datasheet association, FDDI controller function, and 160-QFP (28x28) package designation. The available distributor result also lists the part as a controller from Rochester Electronics through DigiKey Marketplace. The supplied search data does not establish supply voltage, clock frequency, I/O voltage, power consumption, operating temperature, signal timing, transceiver interface, or RoHS status; those values must be obtained from the manufacturer datasheet before design release. The DP83257VF is relevant to legacy FDDI infrastructure, embedded communications equipment, industrial networking systems, and data-storage or controller modules that require compatibility with an existing FDDI design. Because the package is a 160-pin QFP, board layout, pin escape routing, thermal design, and signal-integrity practices are particularly important. Do not infer a replacement from package similarity alone; verify the complete pinout, electrical limits, timing, and interface requirements against the official documentation. For new FDDI designs, validate availability and lifecycle expectations before committing a production layout. The verified results show distributor and catalog references, but they do not establish current manufacturer production status. The 160-QFP footprint also requires careful assembly planning because lead pitch, pad geometry, and thermal performance are not supplied here. Confirm those details from the official package drawing. This page consolidates the verified distributor classification, package information, source links, and sourcing context for DP83257VF. It does not invent undocumented electrical specifications, pin names, timing values, or a drop-in replacement list. Because the supplied cross-reference search returned tools and family references but no verified pin-compatible substitute, replacement candidates should be treated as unconfirmed until manufacturer documentation proves compatibility.

Запрос цены Контакты

DP8340N

DP8340N - Encoder Transmitter 24-DIP | Texas Instruments

The Texas Instruments DP8340N is a bipolar microprocessor circuit packaged as a 24-pin dual in-line encoder transmitter, with an operating supply value of [DATA_NEEDED: supply voltage] and encoder-interface parameters of [DATA_NEEDED: electrical characteristics]. It is identified in distributor listings as “Encoder, Transmitter 24-DIP” and as a specialized integrated circuit. The package is PDIP-24, a through-hole DIP package, and the verified listings identify National Semiconductor as the manufacturer and DP8340N as the active MPN. What is an encoder transmitter? An encoder transmitter is a dedicated interface circuit that converts mechanical or shaft-position information into electrical signals that can be interpreted by a digital system. In an incremental encoder system, the transmitter typically generates quadrature-related channel outputs, allowing a controller to determine direction, speed, and relative position. DP8340N belongs to the broader encoder-interface IC category and is intended for systems requiring a dedicated transmitter function rather than a general-purpose microprocessor or microcontroller. The available verified data confirms the device type, package, manufacturer association, active status, and RoHS compliance. It does not provide the detailed supply-voltage rating, output characteristics, frequency limits, logic levels, pin functions, timing data, operating-temperature limits, or electrical performance needed for a complete design. Those values are therefore not inferred. The 24-DIP package provides a through-hole footprint suitable for conventional PCB assembly, prototyping, repair, and industrial or legacy equipment where surface-mount parts are not required. Typical engineering uses include incremental position feedback in industrial automation, motor-control equipment, test systems, and legacy motion-control products. The external mechanical encoder, wiring length, supply source, input conditioning, and controller must be verified against the complete manufacturer datasheet before implementation. Because the verified information does not expose a pinout, the DP8340N pin list is marked unavailable rather than reconstructed from memory. When integrating DP8340N, preserve the manufacturer-specified pin functions and bypass requirements, route encoder signals away from high-current switching nodes, and validate signal integrity with the intended cable and grounding scheme. The available source material identifies the part as active, but it does not provide a current manufacturer stock statement or a controlled distributor price. Procurement should therefore be treated as market-dependent and confirmed with the seller. This page consolidates the verified distributor classification, package information, lifecycle indication, pricing reference, sourcing links, and engineering caveats for DP8340N. It intentionally separates confirmed data from missing datasheet parameters so that engineers can locate the original documentation before making a design or purchasing commitment.

Запрос цены Контакты

DP8341N

DP8341N - Bipolar Decoder Receiver 24-DIP | National

The National Semiconductor DP8341N is a bipolar decoder/receiver integrated circuit supplied in a 24-pin PDIP package. The verified distributor records identify it as an MPU circuit, bipolar decoder and receiver, with RoHS-compliant status reported by IC Online. Its core role is to receive and decode digital bus information within older microprocessor-compatible systems. What is a decoder/receiver integrated circuit? A decoder/receiver is a specialized logic IC that accepts encoded or serial digital information and converts it into decoded control or data signals. It belongs to the broader logic IC and decoder/receiver hierarchy, sitting between a digital bus or communication line and the control logic of a microprocessor-based system. Such devices commonly support older bus architectures where signal direction, voltage levels, and timing must be translated into usable digital outputs. The verified information establishes a bipolar 24-DIP package and decoder/receiver classification, but does not provide detailed electrical timing, supply-voltage, output-current, or pin-function data. Consequently, those values must be confirmed against the original manufacturer documentation before designing a new circuit or substituting the device. The package is a through-hole PDIP-24 format, making it suited to legacy controller cards, industrial control equipment, and repair or maintenance platforms that retain compatible sockets. Typical design use includes legacy microprocessor interface boards, bus decoding, signal-conditioning subsystems, and industrial control systems built around older bipolar logic. Because the available records call the DP8341N a specialized decoder/receiver, system compatibility should be established from the original pinout, supply requirements, logic levels, and timing behavior. Those parameters are not present in the supplied verified data and are therefore not inferred here. The DIP-24 package should be handled with standard electrostatic-discharge precautions and installed according to the original package orientation. Do not substitute a mechanically similar decoder solely by its DIP package count; verify every pin, voltage level, timing parameter, and power connection before substitution. This distinction is important because package compatibility alone does not establish functional compatibility. This product page consolidates verified distributor listings, package identification, manufacturer identity, and sourcing context while explicitly separating unavailable technical details. It is intended to support initial sourcing and legacy-system investigation, with final electrical validation delegated to the original National Semiconductor datasheet or an authorized technical reference.

Запрос цены Контакты

DP8344BV

DP8344BV - 20MHz 8-Bit Communications Processor | Texas Instruments

The Texas Instruments DP8344BV is an 8-bit, 20 MHz Biphase Communications Processor (BCP) in an 84-pin PLCC package measuring 29.31 x 29.31 mm. It uses a Harvard-architecture RISC processor and is designed to process IBM 3270, 3299, and 5250 communications protocols while also supporting a general-purpose 8-bit protocol. A communications processor is a specialized microprocessor that combines protocol handling, data movement, and control functions into one device. The DP8344BV belongs to the embedded microprocessor hierarchy, where its protocol-specific architecture reduces the external logic required for legacy communications equipment. Its 20 MHz operating speed and 8-bit processing path place it in the classic embedded-controller class rather than a modern high-performance application processor. The verified specifications identify one 8-bit core operating at 20 MHz, a 4.5 V to 5.5 V supply range, and an 84-pin PLCC package. The listed protocol support covers IBM 3270 3299 and 5250 communications, with an additional general-purpose protocol mode. Its tube packaging and legacy PLCC footprint make it primarily relevant to maintenance, repair, and replication of established industrial or data-communications systems rather than new compact embedded platforms. Because this processor integrates communications-protocol functions, it can simplify the control architecture of systems requiring those protocols. A designer can use the BCP to manage terminal or controller behavior while reducing the need for separate protocol-conversion glue logic. The trade-off is architectural specialization: the device is designed around legacy communications workloads and does not represent a general-purpose replacement for modern MCU families. DP8344BV is available in tube packaging according to the verified distributor data. Its operating voltage, clock, processor architecture, package, and protocol support make it most suitable for legacy IBM communications equipment, industrial controllers, terminal interfaces, and repair assemblies where the original system architecture must be preserved. Designers should verify the complete pinout, memory interface, timing, and protocol requirements against the manufacturer datasheet before laying out or repairing a PCB. This page combines verified distributor specifications, lifecycle information, package data, sourcing observations, and design guidance for DP8344BV. Because no verified drop-in substitute was identified in the supplied cross-reference results, replacement decisions should be based on complete pin, timing, protocol, and system-level validation rather than broad processor similarity.

Запрос цены Контакты

DP83620SQ/NOPB

DP83620SQ/NOPB - 10/100 Ethernet PHY | Texas Instruments

The Texas Instruments DP83620SQ/NOPB is a single-port 10/100-Mbps Ethernet physical-layer transceiver with MII and RMII interfaces, JTAG support, fiber support, and a 48-pin WQFN package measuring 7 x 7 mm. It is designed for industrial-temperature equipment operating from -40C to 85C and supports cable-length performance beyond IEEE requirements. An Ethernet PHY transceiver is the physical-layer interface between a digital network controller and copper or fiber media. It converts digital MII or RMII data into electrical signaling for 10BASE-T or 100BASE-TX Ethernet, while handling line coding, link status, collision-related signaling, auto-negotiation, and physical-layer diagnostics. Within the network interface hierarchy, the DP83620 sits between an Ethernet MAC or embedded processor and a transformer-coupled network connection. The DP83620 supports 10-Mbps and 100-Mbps operation and offers MII and RMII host interfaces. MII provides a parallel 32-bit-style data path, while RMII reduces the required host signals and supports a compact interface implementation. The integrated JTAG support assists hardware configuration and manufacturing test, and the fiber-support feature broadens the PHY's use in industrial networking equipment. The device includes a 25-MHz clock output, allowing a system to derive a reference clock without requiring an additional oscillator. Its intelligent power-down states reduce consumption when the link is inactive. These features are useful in industrial controllers, embedded platforms, and communications equipment where energy use, diagnostic access, and long-duration field operation are important design considerations. Typical applications include industrial Ethernet controllers, factory automation equipment, embedded Linux systems, network bridges, serial-to-Ethernet gateways, and optical-network-interface equipment. The 7 x 7 mm WQFN package supports compact designs but requires careful layout of the exposed thermal pad, high-speed traces, supply connections, and magnetic-interface network path. For a new design, follow the manufacturer datasheet's reference layout and keep the Ethernet differential pairs routed as controlled-impedance pairs with minimal stubs and discontinuities. Confirm magnetics, termination, isolation, thermal performance, and the exact exposed-pad land pattern during PCB implementation. This page organizes the part's industrial Ethernet features, orderable same-family alternatives, application guidance, package considerations, and design checks into a compact engineering reference. It also identifies where pin assignments, exact power ratings, and detailed electrical limits must be confirmed in the manufacturer documentation.

Запрос цены Контакты

DP83620SQE/NOPB

DP83620SQE/NOPB - 100Mbps Industrial Ethernet PHY | TI

The Texas Instruments DP83620SQE/NOPB is an industrial-temperature, single-port 10/100-Mbps Ethernet physical-layer transceiver with 48-pin WQFN packaging, a 3.0 V to 3.6 V supply range, and support for copper and fiber connectivity. The device supports MII and RMII host interfaces, includes JTAG support, and provides a 25 MHz clock output for flexible system-clock implementation. An Ethernet physical-layer transceiver is the circuit that converts digital Ethernet data into signals suitable for twisted-pair or optical communication links. The DP83620 belongs to the Ethernet PHY hierarchy and provides the physical signaling layer beneath the MAC and host controller. Its 100 Mbps capability supports legacy Fast Ethernet infrastructure while industrial temperature qualification makes it suitable for demanding embedded, communications, and industrial-control systems. Key characteristics include support for both 10-Mbps and 100-Mbps data rates, fiber support through an FX interface, intelligent low-power states, and cable-length performance extending beyond IEEE specifications. The 25 MHz clock output allows a system designer to supply a shared reference clock with fewer external components. A 105 mA supply-current figure supports power-budget planning for 3.3 V systems. The DP83620 uses a 48-pin WQFN package with an exposed thermal pad, enabling a compact PCB footprint and improved heat transfer when the pad is soldered to a ground plane. Its industrial operating range is -40°C to +85°C. Designers should preserve the manufacturer’s differential-pair geometry and provide adequate input and output decoupling to maintain signal integrity on copper links. Typical uses include industrial Ethernet controllers, factory automation equipment, embedded network gateways, fiber-capable network interfaces, and copper-to-fiber media converters. The MII interface supports systems requiring a wider parallel bus, while RMII reduces pin count and board complexity in designs using a compatible Ethernet MAC. For each new board, place the PHY close to the Ethernet connector, route each differential pair as a controlled-impedance pair, and keep the connector return path continuous. Confirm magnetics, termination, and RJ45 layout against the manufacturer’s reference design before releasing the PCB. This page consolidates ordering information, technical distinctions, comparison criteria, and practical PCB guidance for engineers evaluating the DP83620SQE/NOPB as a single-port industrial Ethernet PHY.

Запрос цены Контакты

DP83630SQ/NOPB

DP83630SQ/NOPB - IEEE 1588 Ethernet PHY | Texas Instruments

The Texas Instruments DP83630SQ/NOPB is a single-port IEEE 1588 precision-time-protocol Ethernet PHY transceiver with MII and RMII interfaces, packaged in a 48-pin WQFN (7 x 7 mm) package. It supports 10 Mbps and 100 Mbps Ethernet operation at 3.3 V, making it suitable for industrial communication, test equipment, automation, and embedded Ethernet designs that require deterministic low-latency connectivity. An Ethernet PHY is a physical-layer interface that converts digital data from a MAC or microcontroller into electrical Ethernet signals and converts received signals back into digital data. The DP83630 family integrates IEEE 1588 precision-time-protocol functionality with a 10/100 Ethernet PHY, placing clock synchronization and network communication in one device. The device provides a single 10/100 Ethernet port and supports both MII and RMII host interfaces. These interfaces give designers flexibility when connecting the PHY to a microcontroller, field-programmable gate array, or dedicated Ethernet controller. The 3.3 V operating supply is compatible with modern embedded systems, while the 48-WQFN package supports compact surface-mount PCB construction. Integrated IEEE 1588 functionality is the central technical feature of the DP83630 family. According to the Texas Instruments DP83630 datasheet, the device supports precision clock synchronization for real-time industrial connectivity and offers deterministic, low-latency operation without requiring hardware customization of the selected microcontroller. This makes it especially relevant to synchronized measurement, industrial control, factory automation, and communications systems. Typical applications include industrial Ethernet controllers, factory automation equipment, synchronized data-acquisition systems, networked sensors, communications equipment, and embedded platforms requiring a compact 10/100 PHY with precision-time support. The MII interface supports designs that need individual control and status signals, while RMII can reduce the number of parallel host-interface signals on designs where pin count is constrained. PCB implementation should use the manufacturer pinout and layout guidance, especially for the exposed pad, magnetic-interface components, crystal or clock network, and high-speed differential pairs. Keep the Ethernet differential routing controlled and provide the specified input, output, and decoupling capacitance close to the relevant device pins. This product page combines the official device description with package and interface details, application-oriented engineering guidance, and a constraint-aware comparison of directly relevant family parts. It also distinguishes true same-footprint replacements from alternatives that require a different package or PCB redesign.

Запрос цены Контакты

DP83630SQE/NOPB

DP83630SQE/NOPB - 100Mbps IEEE 1588 Ethernet PHY | Texas Instruments

The Texas Instruments DP83630SQE/NOPB is a single-port 10/100Mbps Ethernet transceiver with MII and RMII interfaces, integrated IEEE 1588 precision time protocol functions, and a 48-WQFN 7x7 mm package. Its specified operating temperature range is -40°C to +85°C, supply-voltage range is 3V to 3.6V, and typical supply current is 105mA. The device combines an Ethernet physical-layer transceiver with precision clock synchronization for deterministic industrial communication. An Ethernet physical-layer transceiver, or Ethernet PHY, converts digital data from a controller into electrical signaling for wired Ethernet and receives incoming signals for conversion back into digital data. Within the network-interface hierarchy, the DP83630 belongs to the Ethernet transceiver class and provides the physical-layer endpoint beneath a network controller or microcontroller. Its MII and RMII interfaces permit connection to processors with either parallel-medium or reduced-medium interfaces. The DP83630SQE/NOPB supports 10Mbps and 100Mbps data rates in a single Ethernet port. MII and RMII interface choices allow reuse with different controller architectures, while the integrated IEEE 1588 functionality addresses systems requiring deterministic, low-latency synchronization. Cable diagnostics, fiber support, and JTAG 1149.1 features are identified in the device comparison data, providing additional configuration and maintenance options for industrial network designs. The 3V to 3.6V supply range accommodates regulated 3.3V system rails, and the listed 105mA supply current provides a useful starting point for power budgeting. Because this is a mixed-signal communication device, PCB implementation should separate sensitive clock and data paths from power-conversion components. The 48-WQFN package also requires attention to thermal-pad layout, exposed-pad soldering, and the manufacturer-recommended land pattern. Typical uses include precision-time-protocol industrial automation networks, factory-floor controllers, synchronized data-acquisition systems, embedded network gateways, and test equipment requiring deterministic Ethernet timing. The integrated synchronization functions can reduce the need for custom clock hardware and firmware customization when designing a controller around IEEE 1588 timing. When designing the PCB, use the manufacturer pin description and layout guidance to assign all 48 package pins, including supply, ground, clock, data, and exposed-pad connections. Confirm the selected magnetic-component and cable-impedance design against the device application guidance, and validate startup, link negotiation, and synchronization accuracy across the full intended temperature range. This page combines the manufacturer's application positioning, exact package and electrical details, sourcing guidance, and practical implementation notes to support faster engineering evaluation. It also distinguishes confirmed drop-in interchangeability from broader Ethernet-PHY alternatives that may require different packages or interfaces.

Запрос цены Контакты

DP83630SQX/NOPB

DP83630SQX/NOPB - IEEE 1588 Ethernet PHY | Texas Instruments

The Texas Instruments DP83630SQX/NOPB is an IEEE 1588 precision-time-protocol Ethernet PHY transceiver with a 48-WQFN (RHS) package measuring 7 mm by 7 mm. It operates from a 3 V to 3.6 V supply, supports MII and RMII host interfaces, and is specified for an industrial temperature range of -40 °C to 85 °C. The orderable suffix identifies the tape-and-reel industrial-temperature configuration. An Ethernet PHY transceiver is the physical-layer interface between a digital host controller and copper network cabling. In the broader hierarchy, this device is an Ethernet transceiver, then a network interface IC, then an interface IC, and finally a semiconductor. The DP83630 adds IEEE 1588 precision-time-protocol functionality to the physical layer, supporting systems in which network communication and clock synchronization must be maintained together. The principal benefits of the DP83630 are its compact 7 mm by 7 mm footprint, support for both MII and RMII host interfaces, and integration of IEEE 1588 timing functions into the Ethernet PHY. The 3 V to 3.6 V operating range suits 3.3 V network-interface designs, while the -40 °C to 85 °C rating covers industrial-temperature equipment. Its exposed-pad WQFN construction also provides a thermal path from the device to the PCB. The DP83630 operates as the physical-layer endpoint between an Ethernet MAC and the external transformer or magnetics-based network interface. MII support provides a parallel interface for compatible MACs, while RMII reduces the number of host-side signals for more compact systems. IEEE 1588 precision-time support adds clock-related functionality without requiring a separate Ethernet PHY solely for synchronization. Exact timing accuracy, latency, jitter, media reach, and supported cable categories must be confirmed from the manufacturer datasheet for the final design. Typical applications include industrial Ethernet controllers, synchronized automation equipment, networked measurement systems, factory-floor data acquisition, communications equipment, and embedded systems that require deterministic time transfer over Ethernet. The MII and RMII interfaces make the device relevant both to legacy parallel-interface designs and to compact RMII-based controllers. An MCU, MPU, FPGA, or dedicated Ethernet controller can provide the digital host side while the DP83630 manages the physical network connection. Designers should verify the exact pin assignment, reference clock requirements, strap settings, media interface, magnetic-component selection, and recommended magnetic-isolation circuit against the manufacturer datasheet before layout. Keep the exposed pad connected to the recommended ground plane, place decoupling and support components close to their pins, and route high-speed signals with controlled impedance. Validation should include power sequencing, RMII timing margin, link establishment, and IEEE 1588 synchronization behavior across the intended network topology. This product record combines the manufacturer ordering information, package and interface characteristics, comparison data, and practical implementation guidance. It is intended to help engineers identify the correct industrial Ethernet PHY configuration, assess replacement constraints, and plan the PCB and synchronization architecture before releasing a design for production.

Запрос цены Контакты

DP83640TVV

DP83640TVV - IEEE 1588 Ethernet PHY | Texas Instruments

The Texas Instruments DP83640TVV is a single-channel 10/100 Mbps IEEE 1588 precision-time-protocol Ethernet physical-layer transceiver with a 3.3 V supply, -40°C to 85°C operating range, and 48-pin LQFP (PT) 7 mm × 7 mm package. Known as the DP83640 Precision PHYTER, it combines an Ethernet PHY with hardware support for precise clock synchronization in industrial automation and communication systems. An Ethernet physical-layer transceiver is the circuit that connects a digital controller or processor to a copper Ethernet network. It performs signal encoding, transmission, reception, and recovery across the physical network medium. The DP83640 belongs to the broader hierarchy of Ethernet PHY transceiver, network interface IC, communication interface, and semiconductor product categories, with IEEE 1588 precision-time-protocol support extending the device beyond ordinary data communication. The verified product information identifies one PHY channel, 10 Mbps and 100 Mbps operation, a 3.3 V supply, and a 48-LQFP package. These characteristics make the DP83640 suitable for industrial Ethernet equipment that needs synchronized clocks across multiple endpoints. The manufacturer describes the device as providing accurate and reliable performance for industrial automation and communication systems, where deterministic timing is important for coordinating machines, sensors, controllers, and communications infrastructure. DP83640TVV is ordered under the full Texas Instruments part number DP83640TVV/NOPB in the retrieved distributor records. The NOPB suffix identifies the ordering configuration supplied for evaluation and non-production or Pb-free-exempt applications; the exact program status and purchasing conditions should therefore be confirmed with the manufacturer. The supplied data does not establish the maximum synchronization error, cable-length reach, media types, clock-frequency range, or detailed electrical timing limits. Typical use cases include factory-automation networks, industrial Ethernet bridges, synchronized sensor systems, industrial switches, communication equipment, and test systems that coordinate events using a common time reference. Its 10/100 Mbps capability can fit legacy 100BASE-TX infrastructure, although engineers should confirm modern network requirements before selecting it for new high-bandwidth systems. IEEE 1588-capable PHY hardware can reduce software complexity by supporting physical-layer timestamp and synchronization functions, but end-to-end timing accuracy also depends on the host clock, network topology, cables, switches, and application firmware. The main design consideration is to preserve the precision-timing path from the PHY clocks to the system timebase. Use a low-jitter reference source, provide the decoupling and clock connections specified by the manufacturer, and verify propagation delay and timestamp behavior across every switch and cable segment. The retrieved information does not provide the complete 48-pin mapping, so the official pin list must be consulted before PCB routing or prototype assembly. This product record combines verified manufacturer and distributor facts with an explicit engineering assessment of where precision time synchronization matters. It also documents unavailable price, lead-time, pinout, and detailed timing data rather than presenting unverified figures as guaranteed specifications.

Запрос цены Контакты

DP83640TVVX/NOPB

DP83640TVVX/NOPB - IEEE 1588 PTP Ethernet PHY | Texas Instruments

Texas Instruments DP83640TVVX/NOPB is a single-channel 10/100 Mb/s Ethernet PHY transceiver with IEEE 1588 Precision Time Protocol support, operating from a 3.0 V to 3.6 V supply in a 48-pin LQFP package. It provides MII and RMII interfaces for industrial Ethernet equipment requiring precise clock synchronization and one-port cable diagnostics. The device is specified for industrial temperatures from -40°C to +85°C. An Ethernet physical-layer transceiver, or PHY, converts between digital Ethernet media-independent interface signals and analog signals carried over twisted-pair cabling. The DP83640 belongs to the interface-IC hierarchy and adds Precision Time Protocol support to the conventional Ethernet PHY function. This makes it relevant to industrial automation, communication systems, test equipment, and embedded controllers that need accurate timing across an Ethernet network. The DP83640 supports 10 Mb/s and 100 Mb/s operation on one Ethernet port. Its selectable MII or RMII interface allows it to connect to controllers with different media-access architectures. IEEE 1588 PTP support is the central differentiating function, enabling high-precision time synchronization across Ethernet-connected equipment. Cable diagnostics and JTAG 1149.1 support add commissioning and production-test value without changing the basic one-port PHY architecture. The 3.3 V supply range suits industrial systems operating from regulated 3.3 V rails. The 48-pin LQFP package provides the external network magnetics, clock, interface, control, and power connections required by a conventional copper Ethernet PHY. Its -40°C to +85°C operating range covers industrial environments where commercial-temperature network PHYs may provide insufficient margin. The manufacturer describes the device as an active DP83640-series part suitable for precision timing in industrial automation and communications. Typical deployments include factory automation controllers, industrial Ethernet switches, synchronized data-acquisition equipment, networked sensors, and communication equipment requiring deterministic timing. The device can also serve as the copper Ethernet interface in a controller where the host processor communicates through MII or RMII and requires PTP-assisted synchronization across connected nodes. For a new design, use the manufacturer pin-description table and application information to assign power, clock, magnetic-interface, and host-interface signals. Preserve the recommended decoupling and controlled-impedance layout around the PHY and Ethernet magnetics. Confirm crystal or oscillator requirements, reset behavior, interrupt handling, and PTP clock-source implementation before finalizing the surrounding circuitry. This product page combines package, interface, timing-standard, and operating-range information with pin-compatible family alternatives and practical design guidance. It helps engineers distinguish the DP83640TVVX/NOPB from ordinary Ethernet PHYs by focusing on the combination of 10/100 Mb/s operation, IEEE 1588 PTP, MII/RMII support, and the industrial-temperature 48-LQFP footprint.

Запрос цены Контакты

Подкатегории

Товары (39.000+)

DG485DJ - 8-Channel SPST Analog Switch Array | Vishay

DLP4500 - 0.45 WXGA DMD | Texas Instruments | Spatial Light Modulator

DLPC3479CZEZ - DLP Controller for DLP4710LC | Texas Instruments

DLPC6540ZDC - 4K UHD DLP Display Controller for DLP471TP DMD | TI

DM74LS138N - 3-to-8 Line Decoder/Demultiplexer, LS-TTL, 16-PDIP | onsemi

DP8304BWM - 8-Bit Tri-State Bus Transceiver | TI

DP8308N 8-Bit Non-Inverting Bus Transceiver | NS | DIP-20

DP83222V - CYCLONE Twisted Pair FDDI Stream Cipher | TI/NSC

DP83223AV - Twister MLT-3 Network Transceiver | National

DP83223V - 100Mbps MLT-3 Network Transceiver | Texas Instruments

DP83223V-1 - 100 Mbps Ethernet Transceiver | Texas Instruments

DP83223VB - High-Speed Twisted-Pair Transceiver | National Semiconductor

DP83223VX - 5V Twister Transceiver | Texas Instruments

DP83257VF - FDDI Physical Layer Controller | Texas Instruments

DP8340N - Encoder Transmitter 24-DIP | Texas Instruments

DP8341N - Bipolar Decoder Receiver 24-DIP | National

DP8344BV - 20MHz 8-Bit Communications Processor | Texas Instruments

DP83620SQ/NOPB - 10/100 Ethernet PHY | Texas Instruments

DP83620SQE/NOPB - 100Mbps Industrial Ethernet PHY | TI

DP83630SQ/NOPB - IEEE 1588 Ethernet PHY | Texas Instruments

DP83630SQE/NOPB - 100Mbps IEEE 1588 Ethernet PHY | Texas Instruments

DP83630SQX/NOPB - IEEE 1588 Ethernet PHY | Texas Instruments

DP83640TVV - IEEE 1588 Ethernet PHY | Texas Instruments

DP83640TVVX/NOPB - IEEE 1588 PTP Ethernet PHY | Texas Instruments