Товары (44.000+)

INA2133U - Dual 1.5MHz Precision Difference Amplifier | TI
INA2133U

INA2133U - Dual 1.5MHz Precision Difference Amplifier | TI

Texas Instruments INA2133U is a dual-channel, unity-gain precision difference amplifier built around laser-trimmed precision resistor networks. The verified manufacturer information identifies a 1.5 MHz bandwidth, a maximum offset voltage of 450 µV, approximately 0.95 mA of power consumption, and a 14-pin SOIC package. These characteristics position the INA2133U as a high-speed instrumentation amplifier for measuring small differential signals superimposed on larger common-mode voltages. A difference amplifier is an analog signal-conditioning IC that subtracts two input voltages and amplifies the resulting differential component. In the broader electronics hierarchy, it belongs to the instrumentation-amplifier family, which sits within precision analog amplifiers, analog ICs, and semiconductors. Such devices are commonly used to reject common-mode interference, amplify sensor outputs, and preserve signal integrity between sensors and analog-to-digital converters. The INA2133U provides two precision difference amplifiers in one 14-pin SOIC package. Its 1.5 MHz bandwidth supports signal acquisition beyond very slow sensor applications, while the 450 µV maximum offset specification limits input-referred error during low-level measurements. The low 0.95 mA power figure also makes it relevant to compact industrial, communications, and test equipment where each milliampere affects thermal and power-budget requirements. According to the Texas Instruments product page, the device is designed for high-speed precision differential signal conditioning. Internally, the INA2133 combines a precision operational-amplifier core with an on-chip, laser-trimmed resistor network. The manufacturer describes the INA133 and INA2133 families as unity-gain difference amplifiers using high-slew-rate precision operational amplifiers. Laser trimming improves resistor matching and gain accuracy, while matched resistor temperature coefficients help preserve common-mode rejection and gain accuracy over temperature. The dual-channel implementation reduces package count when two independent differential measurements are required. Typical uses include current-sense and low-voltage bridge measurements, industrial sensor interfaces, communications-line signal conditioning, precision test equipment, and differential inputs to data converters. The 1.5 MHz bandwidth is particularly useful when the measured differential signal must be captured without the long settling delays associated with lower-bandwidth instrumentation amplifiers. The 450 µV offset specification should nevertheless be evaluated against the smallest signal amplitude that the application expects to measure. When designing around the INA2133U, check input common-mode range, output swing, supply voltage, gain configuration, and the input/output network required by the selected operating mode. Place the device close to the signal source, maintain short differential traces, and use a quiet return path so that connector or routing noise does not degrade the differential measurement. Decoupling capacitors should be positioned at the supply pins according to the manufacturer application guidance. This page combines the verified manufacturer specifications, current distributor availability, same-family drop-in options, application guidance, and practical design notes. It also distinguishes verified INA2133U characteristics from parameters that still require confirmation from the complete manufacturer datasheet or application-specific calculations.

Запрос цены Контакты
INA2133UA - Dual 1.5MHz Difference Amplifier | Texas Instruments
INA2133UA

INA2133UA - Dual 1.5MHz Difference Amplifier | Texas Instruments

Texas Instruments INA2133UA is a dual, unity-gain precision difference amplifier with 1.5 MHz bandwidth, 450 µV maximum offset voltage, and approximately 0.95 mA power consumption. The device is supplied in a 14-pin SOIC package and is intended for measuring small differential signals in the presence of large common-mode voltages. Its two amplifier channels support independent differential measurements when board space, power, and signal conditioning requirements favor integration. A difference amplifier is a specialized amplifier IC that subtracts two input voltages and amplifies the resulting differential signal. Its internal resistor network establishes the gain and improves common-mode rejection when the paired resistors track closely over temperature. The INA2133 belongs to the difference-amplifier hierarchy, where precision difference amplifier is a subtype of instrumentation amplifier and analog signal-conditioning IC. The manufacturer describes the INA2133 as a high-speed, precision difference amplifier built from a precision operational amplifier and a laser-trimmed resistor network. The INA2133UA provides a maximum input offset voltage of 450 µV, low offset-voltage drift, and maximum gain error of 0.05%. Its 1.5 MHz bandwidth supports higher-frequency signal paths than a slow precision difference amplifier while retaining the gain accuracy required for bridge and sensor measurements. The integrated resistor network is designed for accurate gain and high common-mode rejection. Excellent resistor temperature-coefficient tracking helps maintain gain accuracy and common-mode rejection over temperature. The dual configuration allows two matched differential channels in one package, reducing board area compared with two separate single-channel devices. The manufacturer also offers the related INA133 family in the same high-speed precision difference-amplifier datasheet. Typical uses include bridge-transducer signal extraction, differential sensor measurement, current-shunt monitoring, instrumentation, and factory-automation signal conditioning. The device is particularly suitable when a small differential voltage must be measured in the presence of a larger common-mode voltage and when a unity-gain difference-amplifier implementation would otherwise require several passive and active components. Design the input network, output reference, supply bypassing, and grounding to preserve common-mode rejection and bandwidth. Keep input and feedback routes compact, place bypass capacitors close to the supply pins, and use a low-noise reference for applications that require an output referenced to ground or another system voltage. Confirm the complete pin assignment and operating limits against the manufacturer datasheet before layout release. This product page combines the manufacturer device description, package and ordering information, sourcing availability, strict drop-in alternative screening, and practical design guidance. It also distinguishes directly verifiable INA2133UA characteristics from parameters that require confirmation against the complete manufacturer datasheet before a new design is released.

Запрос цены Контакты
INA2134PA - Dual 0dB Audio Differential Receiver | Texas Instruments
INA2134PA

INA2134PA - Dual 0dB Audio Differential Receiver | Texas Instruments

The Texas Instruments INA2134PA is a dual audio differential line receiver with a fixed gain of 1 V/V, low distortion of 0.0005% at 1 kHz, and a 14 V/µs slew rate. The device is supplied in a 14-pin PDIP package for through-hole audio and instrumentation designs. Each channel uses high-performance operational amplifiers with on-chip precision resistors to convert balanced differential inputs into single-ended audio signals. An audio differential line receiver is a specialized amplifier stage that rejects common-mode noise present on balanced signal pairs while preserving the wanted differential audio voltage. Its place in the signal-chain hierarchy is differential receiver → balanced audio input amplifier → analog signal-conditioning front end. This makes the INA2134PA particularly useful when a stereo source uses balanced left and right channels but the downstream circuitry requires ground-referenced, single-ended audio signals. Key performance characteristics include a fixed 0 dB voltage gain, 90 dB minimum CMRR, 2.9 mA maximum quiescent current, and operation from -18 V to +18 V. According to the TI INA134 and INA2134 datasheet, the receiver combines low distortion with fast settling and wide output-voltage swing. The 14 V/µs slew rate supports accurate reproduction of high-level, high-frequency transients rather than clipping them under moderate loading. The INA2134PA contains two independent receiver channels and internal precision gain-setting resistors. On-chip resistors reduce component count and help maintain consistent channel-to-channel gain without requiring external matched networks. Its differential architecture is useful for rejecting ground-potential differences and coupled interference present between a source and the receiving equipment, especially in professional audio, instrumentation, and industrial control systems. Typical uses include stereo balanced-to-unbalanced conversion, audio measurement front ends, line-level signal conditioning, and instrumentation amplifiers. Because the gain is fixed at 1 V/V, downstream stages must provide any required attenuation or additional amplification. The device is also appropriate for prototypes, repairs, and legacy equipment where a standard 14-pin PDIP footprint and through-hole assembly are preferred over a surface-mount package. When laying out the receiver, connect the balanced input conductors to their assigned differential inputs and route the outputs to the following analog stage with short traces and a stable ground reference. Decouple each supply rail close to the device, keep input and output nodes away from switching-current paths, and verify the output swing against the selected load. This page also organizes package, electrical, and replacement information for faster component selection.

Запрос цены Контакты
INA2134UA - 0dB Audio Differential Receiver | Texas Instruments
INA2134UA

INA2134UA - 0dB Audio Differential Receiver | Texas Instruments

The Texas Instruments INA2134UA is a dual-channel audio differential line receiver with a fixed 1 V/V gain, low distortion, and high slew rate, housed in a 14-pin SOIC package. The receiver is designed for professional audio and other balanced-signal applications where common-mode rejection and signal integrity are important. A differential receiver is an analog signal-conditioning circuit that accepts a pair of complementary or balanced inputs and produces a single output proportional to their difference. The INA2134 family uses high-performance operational amplifiers with on-chip precision resistors. This integrated approach simplifies balanced audio input design and reduces the need for external matched resistor networks. Its differential architecture is part of the broader special-purpose amplifier and signal-conditioning IC hierarchy. The INA2134UA provides 0.0005% distortion at 1 kHz, a 14 V/µs slew rate, and a fixed gain of 1 V/V. The manufacturer specifies a wide supply range of ±18 V and low quiescent current of 2.9 mA maximum. Its high common-mode rejection helps reject shared noise and interference on balanced audio lines, while fast settling and slew-rate performance support dynamic audio signals. The device is offered in single and dual versions, with INA2134UA providing two receiver channels. The 14-pin SOIC package provides a practical surface-mount option for balanced audio preamplifiers, mixer stages, instrument interfaces, and other low-frequency analog systems. The INA2134UA is also specified for operation from -40°C to +85°C, covering the extended industrial temperature range. When using the INA2134UA, preserve the balanced signal path and connect the appropriate input and output decoupling capacitors close to the device pins. Verify source impedance, output loading, cable termination, and common-mode voltage before finalizing the analog layout. Proper grounding and symmetrical routing are important for maximizing common-mode rejection and minimizing distortion. This product page combines the manufacturer specifications, sourcing guidance, drop-in alternatives, application fit, and practical PCB considerations to support faster component selection and design review. It is intended to help engineers identify the correct package, compare suitable alternatives, and implement a stable balanced-audio front end without treating the receiver as a general-purpose precision amplifier.

Запрос цены Контакты
INA2137PA - Dual ±6 dB Audio Receiver | Texas Instruments
INA2137PA

INA2137PA - Dual ±6 dB Audio Receiver | Texas Instruments

Texas Instruments INA2137PA is a dual audio differential line receiver with selectable gain configurations of one-half (1/2, -6 dB) and 2 (+6 dB). The device is packaged as a 14-pin PDIP and is intended for audio and general-purpose differential signal reception. Each receiver channel can reject common-mode noise while extracting the differential signal carried by a balanced line. A differential line receiver is an analog amplifier circuit that compares two input voltages and amplifies their difference. In an audio system, a balanced source sends signal through one conductor and an inverted copy through the other. The receiver rejects voltage shared by both conductors, reducing interference pickup compared with a single-ended input. The INA2137 family is associated with the audio differential line receiver category, the amplifier IC hierarchy, and the broader signal-conditioning and audio interface domain. The INA2137 uses selectable differential gain. Texas Instruments describes a basic one-half gain configuration for differential reception, while reversing the input and feedback resistors produces a gain of 2, corresponding to +6 dB. This arrangement allows a designer to select between attenuation and gain without changing the receiver footprint. The same guidance identifies INA134 and INA2134 as devices intended for unity-gain reception where that behavior is required. The INA2137 family is suitable for professional audio, consumer audio, line-level balanced inputs, instrumentation, and other applications in which a small differential signal must be recovered from a noisy environment. Because the package is a through-hole PDIP, it also supports prototyping and designs assembled with conventional plated-through-hole techniques. Its 14-pin arrangement provides separate positive and negative inputs, output connections, reference pins, and supply connections for two channels. Designers should follow the manufacturer's application schematics when assigning input and feedback resistors. Resistor ratios determine whether each channel operates at one-half gain or a gain of 2. Reference and supply connections must be handled according to the pin-description table in the manufacturer datasheet, particularly when using the reference pins for biasing or output offset management. Decoupling capacitors should be placed close to the device’s supply pins to limit supply-current transients and preserve signal integrity. The INA2137PA is best suited to balanced audio links where -6 dB or +6 dB channel gain is useful and a 14-pin PDIP package fits the assembly process. For unity-gain systems, compare the INA134 or INA2134 families because the INA2137’s documented resistor-configured gains are one-half and 2. This page combines the manufacturer’s device description with practical configuration guidance, package details, sourcing paths, and engineering-oriented replacement analysis.

Запрос цены Контакты
INA2137UA - Dual ±6dB Audio Receiver | Texas Instruments
INA2137UA

INA2137UA - Dual ±6dB Audio Receiver | Texas Instruments

The Texas Instruments INA2137UA is a dual audio differential line receiver with selectable fixed gains of +6 dB and -6 dB, a 14-pin SOIC package, and operation from dual ±18 V supplies. It combines high-performance operational amplifiers with on-chip precision resistors to recover balanced audio signals and reject common-mode interference. An audio differential line receiver is a specialized analog interface that converts a balanced, differential input into a single-ended audio signal. Its functional position is input conditioning: line receiver, differential receiver, analog signal conditioner, and interface IC. Differential reception is particularly useful when two conductors carry the same signal in opposite polarity, allowing common-mode noise to be rejected before the signal reaches an audio-processing or amplification stage. Key features include low distortion of 0.0005% at 1 kHz, a slew rate of 14 V/µs, a fast settling time of 0.01%, and high common-mode rejection of 90 dB. The maximum quiescent current is 2.9 mA, while the wide ±18 V supply range supports conventional professional and consumer audio rails. Each receiver can provide a fixed gain of 1/2 or 2, corresponding to -6 dB or +6 dB. The internal precision-resistor network provides repeatable gain without requiring external gain-setting resistors. This simplifies board design and reduces tolerance-related gain errors. High slew rate preserves large-signal dynamic range in music and speech paths, while low distortion minimizes added harmonic content. The 90 dB CMRR specification helps attenuate hum and interference picked up equally by both input conductors. Typical applications include balanced professional-audio inputs, consumer audio equipment, active speaker systems, audio mixers, and instrumentation interfaces. The dual-channel configuration accommodates left and right channels in one package. The 14-pin SOIC also offers a practical standard footprint for through-hole assembly and conventional surface-mount production. When designing a board around the INA2137UA, preserve the balanced input topology and keep input and return paths appropriately routed. Check output swing, input common-mode range, and gain configuration against the intended signal amplitude. Decoupling capacitors should be placed close to the supply pins, while unused inputs require appropriate treatment according to the manufacturer pin-description table. This product overview combines the device's audio-performance figures, package information, pin and footprint considerations, replacement guidance, and application-level design guidance to support faster component evaluation and board-level implementation.

Запрос цены Контакты
INA213BQDCKRQ1 - 26V Bidirectional Current-Sense IC | TI
INA213BQDCKRQ1

INA213BQDCKRQ1 - 26V Bidirectional Current-Sense IC | TI

The Texas Instruments INA213BQDCKRQ1 is an AEC-Q100 automotive-grade, voltage-output, bidirectional current-shunt monitor rated for common-mode voltages from -0.3V to 26V, packaged in a 6-pin SC-70 DCK package. The device is designed to amplify the small differential voltage produced across a current-sense shunt and convert it into a ground-referenced analog voltage for measurement and control. A current-sense amplifier, also called a current-shunt monitor, is a specialized instrumentation amplifier that measures current indirectly from the voltage drop across a precision shunt resistor. INA213-Q1 belongs to the voltage-output current-shunt-monitor family within instrumentation amplifiers and power-measurement ICs. Its bidirectional measurement supports both positive and negative current flow, making it suitable for motor, battery, automotive, and industrial power-control systems. Verified manufacturer and distributor data identify the INA213BQDCKRQ1 as a 26V, AEC-Q100, high-precision current-sense amplifier. The device supports low-side or high-side measurement, and the official part page identifies the DCK package as a 6-pin SOT-SC70 package. The automotive-grade ordering suffix is consistent with the AEC-Q100 qualification stated by Texas Instruments. The INA21x-Q1 family is intended for applications requiring accurate current measurement across a shunt while the sensed node may sit at a substantially different voltage from the measurement ground. This allows current monitoring in batteries, motor-control systems, electronic loads, power supplies, and automotive electrical systems without placing the shunt at ground potential. The output voltage must remain within the device's valid operating and output limits, so the system designer should verify supply, common-mode, shunt, and output-headroom constraints from the manufacturer datasheet. Typical uses include bidirectional battery-current measurement, DC motor current sensing, solenoid and actuator monitoring, power-supply load current reporting, industrial control input sensing, and automotive load diagnostics. Because the part is bidirectional, it can report charge and discharge current with one signal path rather than requiring separate positive and negative measurement channels. The primary design consideration is the relationship between shunt resistance, sensed current, amplifier gain, input range, and output swing. A higher shunt resistance produces a larger differential signal and can improve measurement resolution, but it also increases power dissipation in the shunt. The PCB should keep the high-current shunt path separate from sensitive input traces, use a low-error reference resistor network, and provide stable supply bypassing close to the device. This page combines verified source data with engineering guidance while clearly identifying parameters that require confirmation from the manufacturer datasheet.

Запрос цены Контакты
INA2141P - Dual G=10/100 Instrumentation Amplifier | Texas Instruments
INA2141P

INA2141P - Dual G=10/100 Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2141P is a dual, low-power instrumentation amplifier offering selectable gains of 10 and 100 in a 16-pin plastic DIP package. Each amplifier combines low offset voltage, low drift, high common-mode rejection, current-feedback input circuitry, and wide bandwidth for precision analog signal conditioning. The INA2141P is designed for applications that require accurate amplification of differential signals in the presence of substantial common-mode voltage. An instrumentation amplifier is a specialized analog amplifier optimized for measuring low-level differential signals, such as sensor outputs, while rejecting common-mode noise and voltage. Unlike a general-purpose operational amplifier, an instrumentation amplifier provides high input impedance, consistent gain accuracy, and strong common-mode rejection in a single integrated circuit. The INA2141 family is a dual instrumentation amplifier, so one package can process two independent channels. The INA2141P supports two fixed gain settings, 10 and 100, and uses current-feedback input circuitry to maintain bandwidth at higher gain. The manufacturer datasheet states that bandwidth reaches 200 kHz at a gain of 100. Low offset voltage is specified at 50 µV maximum, with maximum drift of 0.5 µV/°C and gain accuracy of ±0.05%. Common-mode rejection reaches 117 dB minimum at a gain of 100. The device accepts supply voltages as low as ±2.25 V and operates with supplies up to ±18 V. Input protection extends to ±40 V, helping the amplifier withstand overload conditions in sensor interfaces and industrial measurement systems. Quiescent current is approximately 750 µA per amplifier, making the device suitable for low-power and battery-operated instrumentation. Typical uses include bridge-sensor and pressure-transducer interfaces, medical monitoring, industrial process measurement, current-loop sensing, and laboratory instrumentation. Because the INA2141P is a dual amplifier, it is especially useful for paired sensors or two-stage measurement systems where board area and power consumption are important. Designers should verify the gain-setting resistor configuration, reference-voltage implementation, input common-mode range, and supply headroom against the datasheet before layout. Decoupling capacitors should be placed close to the supply pins, and the analog input traces should be routed away from switching nodes. The manufacturer datasheet also provides application guidance for gain selection, bandwidth, and input protection. This page combines the verified manufacturer and distributor information for INA2141P with package-level guidance, application context, and design considerations that help engineers evaluate the device alongside alternative instrumentation-amplifier implementations.

Запрос цены Контакты
INA2141PA - Dual G=10/100 Amplifier | Texas Instruments
INA2141PA

INA2141PA - Dual G=10/100 Amplifier | Texas Instruments

The Texas Instruments INA2141PA is a dual, low-power instrumentation amplifier with selectable gains of 10 and 100, supplied in a 16-pin PDIP package. It is designed for conditioning differential sensor signals where high input impedance, accurate differential measurement, and a fixed gain range simplify analog front-end design. The dual configuration provides two instrumentation-amplifier channels on one package. An instrumentation amplifier is a specialized analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting signals common to both inputs. Its application hierarchy is instrumentation amplifier, differential amplifier, analog amplifier, signal-conditioning IC, and semiconductor. This makes the INA2141PA appropriate for bridge-based sensing, current measurement, and low-level differential signal acquisition. The INA2141 family offers two supported gain choices, 10 and 100, allowing a designer to select sensitivity according to the expected sensor output. The dual-channel architecture is useful when the system must measure two related quantities, reduce component count, or preserve consistent analog characteristics across channels. Its through-hole PDIP package supports conventional PCB assembly and prototype or repair workflows. According to the manufacturer product page, INA2141 is a low-power instrumentation amplifier intended for precision differential signal conditioning. The device family combines differential input handling with fixed-gain operation, reducing the need for discrete op-amp networks around bridges and sensors. Its dual-channel arrangement also simplifies layout when several low-level signals must be conditioned before conversion or processing. Typical uses include weighing and force sensing, industrial bridge interfaces, current-shunt measurement, biomedical instrumentation, and factory automation. The gain choices make the device useful when a modest input range requires amplification by 10, while a smaller signal such as a millivolt-level bridge output may benefit from the gain-100 setting. For PCB design, place each instrumentation-amplifier channel close to its source to minimize differential pickup and keep high-impedance input routing away from switching nodes. Use a quiet ground reference and follow the manufacturer pin-description table for supply, input, reference, and output connections. Confirm the complete electrical limits, common-mode range, output swing, and recommended external-component values in the manufacturer datasheet. This page organizes the exact package and family information with engineering-oriented application guidance, replacement analysis, comparison fields, and practical layout considerations. It is intended to help engineers confirm fit before committing the INA2141PA to a new sensor-conditioning board.

Запрос цены Контакты
INA2141U - Dual 100V/µs Instrumentation Amplifier | Texas Instruments
INA2141U

INA2141U - Dual 100V/µs Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2141U is a dual-channel, low-power instrumentation amplifier with selectable gains of 10 and 100, 4 V/µs slew rate, and 1 MHz gain-bandwidth product, housed in a 16-pin SOIC (DW) package. Each channel offers a maximum input offset voltage of 50 µV, maximum offset drift of 0.5 µV/°C, and typical gain accuracy of ±0.05%. The devices support bipolar supplies up to ±18 V and include input protection to ±40 V. An instrumentation amplifier is a precision analog signal-conditioning IC that amplifies the differential voltage between two inputs while rejecting common-mode interference. Its internal architecture provides high input impedance, accurate resistor-based gain, and strong common-mode rejection. In the electronic-component hierarchy, the INA2141U is a dual instrumentation amplifier within the broader amplifier IC and signal-conditioning categories. Key features include a low maximum input bias current of 5 nA and a minimum common-mode rejection ratio of 117 dB. These characteristics suit sensor interfaces where source impedance, thermocouple voltages, and small bridge signals must be measured accurately. The low-power design also supports battery-powered instrumentation and compact test equipment where amplifier efficiency and low bias current influence overall system error. The internal gain architecture offers a choice of 10 or 100 to match both moderate and high-sensitivity measurement ranges. A 1 MHz gain-bandwidth product supports signal bandwidth required by many industrial, medical, and laboratory systems, while the 4 V/µs slew rate improves large-signal response. Maximum input offset voltage of 50 µV and drift of 0.5 µV/°C limit errors in low-level DC measurements. Typical uses include bridge excitation and readout, pressure and strain-gauge amplification, biopotential front ends, battery-powered sensor modules, current-shunt measurements, and precision data-acquisition systems. The 16-pin SOIC package allows conventional surface-mount assembly, while the dual-channel configuration can reduce board area when two differential inputs must be conditioned. Designers should use the manufacturer pin-description table to assign input, feedback, reference, power, and output connections. Input filtering, reference-grounding, and supply-bypass placement require care because parasitic resistance can degrade CMRR and offset performance. Input protection ratings should not be interpreted as a substitute for external surge protection in hazardous or high-energy systems. This page consolidates the key INA2141U specifications, verified package information, application guidance, and confirmed replacement references into a practical engineering comparison. It also distinguishes direct pin-compatible options from related INA214x devices whose gain and channel characteristics differ.

Запрос цены Контакты
INA2141UA - Dual G=10,100 Instrumentation Amplifier | TI
INA2141UA

INA2141UA - Dual G=10,100 Instrumentation Amplifier | TI

The Texas Instruments INA2141UA is a dual, low-power instrumentation amplifier in a 16-pin SOIC package, with signal gain options of 10 and 100 and a listed gain-bandwidth product of 200 kHz. It is designed for amplifying small differential sensor signals in industrial measurement, instrumentation, and analog front-end systems. The package is identified as 16-SOIC, measuring 0.295 inch, or 7.50 mm, in body width. An instrumentation amplifier is a precision analog amplifier optimized for differential signals. Its internal architecture amplifies the voltage difference between two inputs while rejecting common-mode noise, which is important when a sensor output is small relative to the surrounding electrical environment. The INA2141 belongs to the wider category of operational amplifier ICs and analog signal-chain devices used to condition, scale, and route sensor signals before conversion or control. Key confirmed features include dual amplifier channels, low-power operation, selectable gains of 10 and 100, a 200 kHz listed bandwidth figure, and a 16-pin SOIC package. The dual configuration allows one device to serve two independent analog channels, reducing component count when the board area is constrained. The two gain settings also support different sensor ranges without changing the overall signal-chain architecture. The device uses a three-operational-amplifier instrumentation-amplifier approach to provide differential input handling and high common-mode rejection. Exact input common-mode range, output swing, supply range, input bias current, offset voltage, noise density, and quiescent current should be confirmed in the manufacturer datasheet before the circuit is released for production. Typical uses include bridge-sensor front ends, pressure and force measurement, current-shunt monitoring, battery-cell sensing, and industrial instrumentation. The dual-channel arrangement is particularly useful when two sensors must be measured under similar electrical conditions, while the 200 kHz gain-bandwidth figure supports signal bandwidths appropriate for many slow-to-moderate industrial sensing tasks. Design layouts should provide short, symmetric input traces, a stable reference configuration, and careful grounding around the analog inputs. Because the INA2141UA operates in a differential measurement environment, input filtering, protection, and connector grounding determine whether the amplifier sees the intended signal or external interference. This page consolidates the confirmed ordering information, package details, functional attributes, application fit, and replacement considerations. It also identifies the technical parameters that should be checked in the manufacturer datasheet before schematic sign-off, helping engineers move from part selection to a validated analog front-end design.

Запрос цены Контакты
INA2141UG4 - Dual 10/100 Gain Instrumentation Amp | TI
INA2141UG4

INA2141UG4 - Dual 10/100 Gain Instrumentation Amp | TI

The Texas Instruments INA2141UG4 is a dual, low-power instrumentation amplifier with selectable gains of 10 or 100, a 200 kHz bandwidth at gain 100, and a 16-pin SOIC package. Each amplifier provides one instrumentation-amplifier channel, allowing two independent differential measurements in a compact surface-mount design. An instrumentation amplifier is a precision analog circuit that amplifies the voltage difference between two inputs while rejecting common-mode signals. The INA2141 belongs to the instrumentation-amplifier hierarchy within amplifier ICs and analog signal-chain conditioning. Its internal three-op-amp architecture supports current-feedback input circuitry, preserving useful bandwidth at high gain and simplifying front-end design for bridge sensors, low-voltage sensing, and industrial measurement systems. Key characteristics include two amplifiers per package, gain options of 10 and 100, 200 kHz bandwidth at a gain of 100, and a typical signal-to-noise ratio listed at 117 dB. The operating temperature range extends from -40 °C to +85 °C. The gain-setting arrangement eliminates the need for external feedback resistors, while the integrated input circuitry reduces component count and makes the device suitable for compact, high-impedance sensing nodes. Technically, the INA2141 combines differential input handling with internal feedback networks and an output amplifier in each channel. Current-feedback input circuitry is the key bandwidth feature: the specified 200 kHz gain-bandwidth behavior at gain 100 supports faster signal capture than a typical low-frequency precision-only instrumentation amplifier. The device operates from a 5 V supply and consumes approximately 15 mA, balancing channel density, measurement bandwidth, and power consumption for portable and industrial equipment. Typical uses include precision bridge excitation for pressure and load cells, current-sense amplification in power systems, battery and energy monitoring, biomedical instrumentation interfaces, and factory sensor acquisition. In bridge-based measurements, the amplifier rejects supply and ground disturbances shared by both sensor inputs. In current sensing, it magnifies a small differential shunt voltage while limiting the influence of common supply variation. A critical design consideration is input and output range: the selected gain and 5 V supply determine the usable differential and output spans. Review the absolute maximum and recommended operating conditions in the manufacturer datasheet before applying large bridge or shunt inputs. PCB placement should keep sensitive input traces short, provide a stable reference or return path, and separate analog routing from switching-converter and digital timing nodes. This page combines manufacturer electrical characteristics, package and ordering information, sourced pricing, drop-in replacement guidance, and application-focused engineering guidance. It is intended to help engineers evaluate the INA2141UG4 for precision differential measurement while identifying the key electrical and layout checks required before release to production.

Запрос цены Контакты
INA2143U - 5-V/µs Dual Precision Difference Amplifier | TI
INA2143U

INA2143U - 5-V/µs Dual Precision Difference Amplifier | TI

The Texas Instruments INA2143U is a dual high-speed precision difference amplifier featuring 5 V/µs slew rate, 250 µV offset, selectable gain settings of 10 or 0.1, and a 14-pin SOIC package. The device is intended for systems that measure small voltage differences and require amplified differential outputs. A difference amplifier is a specialized operational-amplifier circuit that compares voltages applied to its inverting and non-inverting inputs and amplifies the voltage between them. This method helps reject signals that appear equally on both inputs, making difference amplifiers useful within measurement, instrumentation, analog-control, and signal-conditioning systems. The INA2143U belongs to the amplifier IC category and combines two precision difference amplifiers in one package. Key features include a 5 V/µs slew rate, 250 µV offset, gain options of 10 and 0.1, dual-channel operation, and an operating temperature range of -55°C to 125°C. The 5 V/µs slew rate allows the output to respond quickly to input-voltage changes, while the selectable gain provides flexibility for different differential-signal levels. Each channel can support the two stated gain configurations. The INA2143U combines two difference amplifiers in a single 14-pin SOIC (D) package, reducing board area when two differential channels are required. Its high-speed and precision positioning makes it applicable to fast analog signal conditioning, where the main design objective is to preserve the relationship between two input voltages while converting the differential signal into a single-ended output. Typical applications include current-sense amplifier front ends, differential sensor interfaces, bridge-based measurement circuits, industrial instrumentation, and analog control systems. In a current-sense design, the amplifier processes the voltage generated across a sense resistor rather than the full supply voltage. In a bridge or differential sensor interface, it rejects common-mode voltage and preserves the smaller differential component being measured. Designers should use the manufacturer pin-description table when assigning traces and power connections, and they should verify signal amplitudes against the selected gain of 10 or 0.1. PCB placement should minimize resistive and capacitive pickup around the differential inputs, while supply bypassing should follow the connection and capacitor recommendations in the manufacturer datasheet. This page combines the confirmed INA2143U operating characteristics with practical selection guidance, application context, package information, and drop-in replacement validation. It distinguishes confirmed device attributes from parameters that require confirmation from the complete manufacturer datasheet, helping engineers plan sourcing and circuit design with fewer assumption-driven steps.

Запрос цены Контакты
INA217AIP - Low-Noise Instrumentation Amplifier | Texas Instruments
INA217AIP

INA217AIP - Low-Noise Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA217AIP is a low-noise, low-distortion monolithic instrumentation amplifier in an 8-pin PDIP package. It accepts a 4.5 V to 18 V supply, provides a typical gain of 3 V/V, features 250 µV input offset voltage, and supports a slew rate of 15 V/µs with 3.4 MHz bandwidth. An instrumentation amplifier is a specialized amplifier optimized for measuring low-level differential signals. Its internal signal path rejects common-mode noise while amplifying the voltage difference between two inputs. The INA217 belongs to the instrumentation amplifier, differential amplifier, analog amplifier, and signal-conditioning IC hierarchy, making it suitable for precision sensor conditioning, balanced audio, industrial measurement, and medical instrumentation. The device uses current-feedback circuitry to provide wide bandwidth and strong dynamic response over a broad gain range. Its distortion-cancellation architecture is intended to maintain low distortion even at higher gain. The manufacturer identifies near-theoretical noise performance for a 200 Ω source impedance, making balanced low-impedance microphone signals a primary use case. The monolithic implementation also provides differential inputs, low noise, and low distortion in one package. INA217AIP is identified as a replacement for the SSM2017 and is available with the same DIP-8 and wide-body SOL-16 pin arrangements. The DIP-8 format is useful when an existing instrument-amplifier layout must be retained. Its 15 V/µs slew rate supports high-level audio stages, while differential input handling improves rejection of common-mode interference in measurement systems. Typical applications include professional microphone preamplification, low-level bridge or transducer signal conditioning, industrial process measurement, and medical monitoring. In a microphone circuit, the part processes the differential output of a balanced capsule while rejecting much of the shared noise appearing on both signal conductors. Its low-noise, low-distortion characteristics help preserve the signal-to-noise ratio of the source. When designing around INA217AIP, preserve the pin arrangement of the original SSM2017 layout and follow the manufacturer datasheet for gain-setting resistors, supply bypass capacitors, and output drive requirements. Check input common-mode range, output swing, and source impedance at the selected gain because instrumentation amplifiers can become input-voltage-range constrained even when their bandwidth remains adequate. This product page combines the manufacturer electrical description, package information, compatible-device context, and application-level engineering guidance. It also distinguishes direct replacements from alternatives that require different packages, helping designers evaluate PCB reuse, signal bandwidth, and noise performance before committing to a component.

Запрос цены Контакты
INA2181 26V Dual-Channel Current Sense Amp | TI | Gain 20 V/V
INA2181A1IDGSR

INA2181 26V Dual-Channel Current Sense Amp | TI | Gain 20 V/V

The Texas Instruments INA2181 (e.g., INA2181A1IDGSR) is a 26V, dual-channel, bidirectional, 350kHz voltage-output current sense amplifier in a 10-pin VSSOP (DGS) package, part of the cost-optimized INAx181 family. It senses voltage drops across shunt resistors on low- or high-side rails and outputs a ground-referenced analog voltage proportional to load current. A current sense amplifier (also called a current-shunt monitor) is a specialized difference amplifier that extracts a small differential shunt voltage riding on a large common-mode voltage and converts it to a ground-referenced single-ended signal. Within the signal chain hierarchy it sits between the shunt resistor and an ADC or comparator, serving as a front-end element of power management and battery monitoring systems. Key features include a wide 2.7V to 26V common-mode range that is independent of the 2.7V to 5.5V supply, 350kHz bandwidth for fast load-transient monitoring, bidirectional operation with a reference pin for charging/discharging current measurement, and factory-calibrated gain options (A1 = 20 V/V, A2 = 50 V/V, A3 = 100 V/V, A4 = 500 V/V) that eliminate gain-setting resistors. The zero-drift architecture delivers low offset for small shunt voltages. The dual channels share one package, halving board area versus two single-channel monitors such as the INA181. Rail-to-rail output swings close to the supply rails, maximizing ADC dynamic range. All device options are specified from -40C to +125C. Typical applications include battery current monitoring in portable and industrial equipment, DC motor drive phase and bus current sensing, telecom and server power supply current telemetry, and load-current supervision in 12V/24V rails feeding TI C2000 or MSPM0 MCUs. Design tip: keep the shunt voltage in the 10 mV to 100 mV range at full load - large enough to swamp offset error, small enough to limit shunt power dissipation. Route Kelvin sense traces directly to the shunt pads to preserve accuracy.

Запрос цены Контакты
INA2181A3IDGSR - 26V Dual-Channel Current Sense Amp | TI
INA2181A3IDGSR

INA2181A3IDGSR - 26V Dual-Channel Current Sense Amp | TI

The Texas Instruments INA2181A3IDGSR is a 26V, dual-channel, bidirectional voltage-output current sense amplifier with a fixed gain of 100 V/V (A3 version), 350 kHz bandwidth, and a common-mode input range of -0.2 V to +26 V, housed in a 10-pin VSSOP (DGS) package rated from -40C to +125C. A current sense amplifier (also called a current-shunt monitor) is a specialized difference amplifier that senses the small voltage drop across a shunt resistor and converts it into a ground-referenced output signal. Within the power-management IC hierarchy, it sits alongside voltage regulators and battery-management devices as a core building block of power monitoring and protection subsystems. Key features include the wide -0.2 V to +26 V common-mode range that operates independently of the supply voltage, enabling high-side and low-side sensing on 24 V industrial rails. The A3 gain option of 100 V/V with a 2 V/us output slew rate and 350 kHz bandwidth suits fast, medium-sensitivity current monitoring. Offset voltage is tightly specified: a maximum of plus/minus 150 uV at VCM = 0 V and plus/minus 500 uV at VCM = 12 V, according to the TI datasheet. The INAx181 architecture senses bidirectional current with an external reference voltage applied to the REF pin, allowing the output to be offset for positive and negative current indication. Rail-to-rail output swing maximizes ADC dynamic range on low-supply rails, and the cost-optimized design targets volume production. Typical applications include battery charging systems, 24 V industrial power supplies, motor drive DC bus monitoring, and telecom or server power-supply current telemetry where two channels share one shunt scheme or monitor two rails. Design consideration: keep the shunt resistor value and the A3 gain of 100 V/V balanced - a 10 mV full-scale shunt drop yields 1 V output, so size the shunt to use the ADC input range without exceeding the output swing limits. This page synthesizes distributor pricing, drop-in alternatives within the INAx181 family, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
INA2181A4QDGSRQ1 - 26V Dual 350kHz Current Sense Amp AEC-Q100 | TI
INA2181A4QDGSRQ1

INA2181A4QDGSRQ1 - 26V Dual 350kHz Current Sense Amp AEC-Q100 | TI

The Texas Instruments INA2181A4QDGSRQ1 is an AEC-Q100 qualified, 26V, dual-channel, bidirectional current sense amplifier (also called a current-shunt monitor) with a 350 kHz bandwidth and a fixed gain of 200 V/V (A4 gain variant), housed in a 10-pin VSSOP (DGS) package. It senses voltage drops across current-sense resistors at common-mode voltages from -0.2 V to +26 V, independent of its own supply voltage, and provides a rail-to-rail voltage output. A current sense amplifier is a specialized difference amplifier, within the broader hierarchy of instrumentation amplifiers and operational amplifier signal-conditioning ICs, designed to measure the small differential voltage developed across a shunt resistor and convert it into a ground-referenced output voltage proportional to load current. Bidirectional devices like the INA2181 also detect current flowing in both directions, which is essential in battery charging and discharging monitoring. Key features of the INA2181A4QDGSRQ1 include the wide -0.2 V to 26 V common-mode range that survives automotive load-dump-adjacent conditions, dual-channel integration that halves board area versus two single-channel amplifiers, a 350 kHz bandwidth suitable for fast current-loop control, and the cost-optimized INAx181-Q1 family architecture. Technically, the INA2181-Q1 uses a zero-drift-free precision front end with a fixed gain set by internal resistors; the A4 variant provides 200 V/V gain, allowing very small shunt resistances (sub-10 mOhm) to be used, reducing shunt power dissipation at high currents. The voltage output architecture requires no ADC-side gain stage and simplifies interfacing with microcontroller ADC inputs. Typical applications include automotive battery management systems, 48V and 12V automotive power rails, industrial motor drives, telecom -48V systems, and server hot-swap current monitoring. Design-wise, place the shunt resistor close to the amplifier inputs, use Kelvin (4-wire) connections to the sense resistor, and filter differential noise at the inputs. Note that the 200 V/V gain limits full-scale shunt voltage to about 20 mV for a 4 V output swing. This page synthesizes distributor pricing, drop-in same-family gain-variant alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
INA240A1D - 20V/V Bidirectional Current Sense Amp | TI
INA240A1D

INA240A1D - 20V/V Bidirectional Current Sense Amp | TI

The Texas Instruments INA240A1D is a bidirectional, zero-drift current-sense amplifier with a gain of 20 V/V, a common-mode voltage range of -4 V to 80 V, and an 8-pin SOIC package. It measures the voltage developed across a shunt resistor on either the high side or low side of a power path and produces an analog output proportional to current. A current-sense amplifier is a specialized instrumentation amplifier that converts the small differential voltage across a current shunt into a larger, easier-to-process voltage. The INA240 family belongs to the amplifier hierarchy as a current-sense amplifier, instrumentation amplifier, analog IC, and semiconductor. Its common-mode range allows the shunt to remain near a supply rail while high voltage, high current, or both are present in the monitored circuit. The INA240A1D combines a 20 V/V gain setting with bidirectional operation and enhanced PWM rejection. Zero-drift architecture minimizes output drift as temperature changes, while the -4 V to 80 V common-mode range supports demanding industrial power systems. Its analog output can be centered near ground for bidirectional current measurement by applying the appropriate reference configuration. The device also supports unidirectional sensing when both reference pins are tied to ground. Internally, the device provides precision differential sensing, a low-offset amplifier, and an analog output stage. Because the common-mode input range is independent of the supply voltage in the relevant operating region, the INA240 can sense voltage drops across a high-side shunt without requiring the amplifier supply to exceed the sensed bus voltage. This architecture is particularly useful when PWM switching nodes create large common-mode transients. Typical applications include motor-control systems, industrial power supplies, robotics, solar inverters, battery packs, solenoid drivers, LED drivers, and protected DC power rails. The INA240A1D is especially appropriate when current must be measured bidirectionally, the shunt may sit above ground, and PWM rejection is important. A 20 V/V gain also reduces the required shunt resistance when the measured current range is relatively low. When designing the circuit, verify that the shunt power dissipation remains below its rating and that the amplifier output stays within its valid output range at maximum load current. Place the differential input traces directly across the shunt, keep them short and symmetric, and provide stable supply decoupling close to the device. Do not exceed the absolute maximum ratings for supply voltage, common-mode voltage, or input voltage. This page combines manufacturer specifications, drop-in alternatives, application guidance, and practical design notes for engineers evaluating the INA240A1D in motor, industrial, and high-side current-measurement systems.

Запрос цены Контакты
INA240A1PW - 80V Bidirectional Current Sense Amp | TI TSSOP-8 (Tape & Reel)
INA240A1PW

INA240A1PW - 80V Bidirectional Current Sense Amp | TI TSSOP-8 (Tape & Reel)

The Texas Instruments INA240A1PW is a -4 V to 80 V bidirectional, ultra-precise current-sense amplifier with enhanced PWM rejection, housed in an 8-pin TSSOP (PW) package with a fixed gain of 20 V/V. It senses drops across shunt resistors over a wide common-mode range independent of supply voltage and integrates a zero-drift chopper architecture that keeps input offset below 25 uV and offset drift below 100 nV/°C. What is a current-sense amplifier? A current-sense amplifier is a specialized analog IC that measures the small differential voltage developed across a shunt resistor carrying the load current, then amplifies that millivolt-level signal to a ground-referenced output that an ADC, microcontroller, or comparator can read. As a member of the power-management and amplifier IC hierarchy, the INA240 family combines a precision difference amplifier with PWM-rejection circuitry, allowing it to ignore large dV/dt transients from switching power stages while still maintaining high DC accuracy. Key features include 20 V/V gain (A1 variant), 132 dB DC common-mode rejection ratio (CMRR), a 1.5 MHz bandwidth, and 1.6 mA maximum quiescent supply current from a 2.7 V to 5.5 V supply rail. Enhanced PWM rejection suppresses transients from 60 V/ns common-mode slew events that occur when measuring current in motor-drive and solenoid circuits, allowing accurate readings through PWM edges without blanking. The INA240 architecture pairs an input EMI filter and chopper-stabilized front end with a precision output stage. The chopper stabilization shifts the 1/f noise to a higher frequency where it is filtered out, yielding the 5 uV/°C typical offset drift and 25 uV maximum input offset specified across the -40°C to +125°C operating range. Independent supply and common-mode ranges allow the IC to operate from a 3.3 V logic rail while sensing high-side current at 24 V, 36 V, or 48 V industrial bus voltages. Typical applications include 48 V brushed and brushless DC motor control, solenoid and valve current monitoring, server and telecom 12 V/24 V hot-swap current sensing, power-converter feedback, and battery-pack current monitoring in e-mobility and industrial robots. The A1 gain of 20 V/V suits low-side and high-side sensing where shunt full-scale drop is on the order of 75 mV. When designing with this device, choose the shunt resistor so that peak differential voltage at maximum load stays within the linear output range (typically 0.1 V to VS - 0.1 V), and place a 1 nF to 10 nF RC network on the input pins if the layout introduces parasitic common-mode noise. Use Kelvin (4-terminal) connection to the shunt to keep ground-loop errors out of the measurement. This page synthesizes real-time distributor pricing, drop-in alternatives, and design notes that go beyond the manufacturer datasheet, giving engineers a one-stop reference for the INA240A1PW.

Запрос цены Контакты
INA240A1PWR - 80V Bidirectional Current Sense Amp | TI TSSOP-8
INA240A1PWR

INA240A1PWR - 80V Bidirectional Current Sense Amp | TI TSSOP-8

The Texas Instruments INA240A1PWR is a -4 V to 80 V bidirectional, ultra-precise current-sense amplifier with enhanced PWM rejection, housed in an 8-pin TSSOP (PW) package with a fixed gain of 20 V/V. It senses drops across shunt resistors over a wide common-mode range independent of supply voltage and integrates a zero-drift chopper architecture that keeps input offset below 25 uV and offset drift below 100 nV/°C. What is a current-sense amplifier? A current-sense amplifier is a specialized analog IC that measures the small differential voltage developed across a shunt resistor carrying the load current, then amplifies that millivolt-level signal to a ground-referenced output that an ADC, microcontroller, or comparator can read. As a member of the power-management and amplifier IC hierarchy, the INA240 family combines a precision difference amplifier with PWM-rejection circuitry, allowing it to ignore large dV/dt transients from switching power stages while still maintaining high DC accuracy. Key features include 20 V/V gain (A1 variant), 132 dB DC common-mode rejection ratio (CMRR), a 1.5 MHz bandwidth, and 1.6 mA maximum quiescent supply current from a 2.7 V to 5.5 V supply rail. Enhanced PWM rejection suppresses transients from 60 V/ns common-mode slew events that occur when measuring current in motor-drive and solenoid circuits, allowing accurate readings through PWM edges without blanking. The INA240 architecture pairs an input EMI filter and chopper-stabilized front end with a precision output stage. The chopper stabilization shifts the 1/f noise to a higher frequency where it is filtered out, yielding the 5 uV/°C typical offset drift and 25 uV maximum input offset specified across the -40°C to +125°C operating range. Independent supply and common-mode ranges allow the IC to operate from a 3.3 V logic rail while sensing high-side current at 24 V, 36 V, or 48 V industrial bus voltages. Typical applications include 48 V brushed and brushless DC motor control, solenoid and valve current monitoring, server and telecom 12 V/24 V hot-swap current sensing, power-converter feedback, and battery-pack current monitoring in e-mobility and industrial robots. The A1 gain of 20 V/V suits low-side and high-side sensing where shunt full-scale drop is on the order of 75 mV. When designing with this device, choose the shunt resistor so that peak differential voltage at maximum load stays within the linear output range (typically 0.1 V to VS - 0.1 V), and place a 1 nF to 10 nF RC network on the input pins if the layout introduces parasitic common-mode noise. Use Kelvin (4-terminal) connection to the shunt to keep ground-loop errors out of the measurement. This page synthesizes real-time distributor pricing, drop-in alternatives, and design notes that go beyond the manufacturer datasheet, giving engineers a one-stop reference for the INA240A1PWR.

Запрос цены Контакты
INA240A2D - 50V/V Bidirectional Current-Sense Amplifier | Texas Instruments
INA240A2D

INA240A2D - 50V/V Bidirectional Current-Sense Amplifier | Texas Instruments

The Texas Instruments INA240A2D is a bidirectional, precision current-sense amplifier with a fixed gain of 50 V/V, a common-mode operating range from -4 V to 80 V, and an 8-pin SOIC package. It is designed to measure small shunt-resistor voltage drops while rejecting PWM-related transients, making it suitable for motor drives, solenoid controls, power converters, and battery systems. A current-sense amplifier is a specialized instrumentation amplifier that converts the differential voltage across a precision shunt resistor into a scaled voltage proportional to current. The INA240 belongs to the current-sense amplifier category and the broader amplifier and measurement IC hierarchy. Its bidirectional architecture supports both positive and negative current, while its negative common-mode capability allows operation below ground during the flyback interval of inductive loads. The A2 gain option provides 50 V/V amplification, allowing a small shunt drop to produce an easily measurable output. The -4 V to 80 V common-mode range supports low-voltage motor systems, industrial 24 V and 48 V buses, and automotive-style transient environments. The manufacturer identifies the device as an ultra-precise current-sense amplifier with enhanced PWM rejection. Its operating temperature range extends from -40 °C to +125 °C for industrial and automotive temperature-grade designs. The INA240 uses a differential input arrangement to reject supply ripple and common-mode voltage while measuring the shunt differential. Bidirectional operation allows the output to move above or below ground to indicate current direction. The 8-SOIC format supports conventional surface-mount assembly and provides a practical package for power-control boards where the shunt may be separated from sensitive analog circuitry. Typical uses include BLDC and brushed motor control, solenoid and relay current monitoring, DC-DC converter feedback, battery charge and discharge measurement, inverter leg monitoring, and industrial power-supply protection. The wide common-mode range is particularly useful when the sensed current is switched while the amplifier supply remains independent of the high-voltage power rail. Design the shunt and analog path carefully. Keep the differential input traces short and symmetric, place the amplifier close to the shunt, and use low-value resistors with appropriate pulse ratings. Input filtering must preserve the intended measurement bandwidth while attenuating high-frequency switching noise. Verify common-mode voltage, output swing, supply headroom, thermal performance, and amplifier saturation before committing the PCB layout. This page consolidates the device architecture, operating limits, application guidance, package details, sourcing workflow, and drop-in replacement analysis into one engineering reference. It also identifies where application-specific values must be calculated from the actual shunt resistance, current waveform, board environment, and power-supply topology.

Запрос цены Контакты
INA240A2DR - 50V/V Bidirectional Current Sense Amplifier | Texas Instruments
INA240A2DR

INA240A2DR - 50V/V Bidirectional Current Sense Amplifier | Texas Instruments

The Texas Instruments INA240A2DR is a bidirectional, zero-drift current-sense amplifier with a fixed gain of 50 V/V, a -4 V to 80 V common-mode input range, and enhanced PWM rejection. It is packaged in an 8-pin SOIC and operates from a single 5.5 V supply. A current-sense amplifier is a specialized amplifier that measures the voltage developed across a shunt resistor placed in a current-carrying conductor. The INA240 belongs to the current-sense amplifier hierarchy within instrumentation amplifiers and analog signal-chain ICs. It converts the small differential shunt voltage into an amplified voltage proportional to current, supporting both positive and negative current measurement. The A2 gain code sets the nominal amplification to 50 V/V. Its wide common-mode range permits sensing current above ground, at ground, and down to -4 V, which is useful in systems with inductive flyback or ground-offset returns. Bidirectional operation means that the output can represent positive or negative current without changing the basic shunt arrangement. Enhanced PWM rejection helps suppress switching disturbances commonly encountered in motor-control and power-conversion systems. The device uses a zero-drift architecture intended to provide accurate current measurement over changing temperatures and time. The manufacturer describes the INA240 family as ultra-precise and optimized for shunt-based measurements. Because the output is proportional to the shunt differential voltage, the shunt resistance determines the conversion between current and amplifier output voltage. Typical uses include motor and solenoid current monitoring, power-converter feedback, battery current measurement, industrial control systems, and automotive-style PWM systems. The 8-pin SOIC format supports conventional surface-mount assembly and compact analog layouts. Placement close to the shunt helps minimize pickup from adjacent switching nodes. Designers should verify the complete pin configuration, recommended input filtering, output-voltage range, and absolute maximum ratings in the manufacturer data sheet before layout. Kelvin routing from the shunt terminals and careful grounding are especially important because small differential signals can be corrupted by shared copper impedance or high-current return paths. This page combines the manufacturer's core INA240 characteristics with exact-MPN commercial information, same-family drop-in options, application guidance, and practical PCB considerations for engineers evaluating the INA240A2DR in a current-measurement design.

Запрос цены Контакты
INA240A2PW - 50V/V Bidirectional Current Sense Amp | Texas Instruments
INA240A2PW

INA240A2PW - 50V/V Bidirectional Current Sense Amp | Texas Instruments

Texas Instruments INA240A2PW is a bidirectional, precision current-sense amplifier with a gain of 50 V/V, a -4 V to +80 V common-mode voltage range, and an operating temperature range of -40 °C to +125 °C. The device is packaged in an 8-pin TSSOP (PW) package and is designed for high-side or low-side current measurement in systems exposed to fast common-mode transients. A current-sense amplifier is an instrumentation amplifier that measures the small voltage developed across a current shunt and converts it into an amplified voltage proportional to current. This device belongs to the instrumentation-amplifier and current-sense-amplifier hierarchy, where its differential measurement, low offset voltage, and common-mode rejection improve the accuracy of power, motor, solenoid, and battery monitoring systems. The A2 gain option provides 50 V/V amplification. The INA240 family operates from a 5.5 V supply and accepts common-mode voltages extending from -4 V to +80 V. Its enhanced PWM rejection is intended to suppress transient disturbance caused by switching power stages, while bidirectional operation allows measurement of positive or negative current without changing the signal path architecture. The common-mode range and PWM rejection make the INA240A2PW especially useful where the shunt is placed near a motor, actuator, or inductive load. Although the analog output must remain within the amplifier's supply-voltage limits, the input common-mode voltage can move independently across the stated -4 V to +80 V range. This separation between input common-mode capability and output-supply limits is central to correct application design. Typical uses include DC motor current control, solenoid and actuator monitoring, battery pack current measurement, industrial power conversion, and electronic loads. The precision architecture is also appropriate for systems that must recover a small shunt voltage accurately while rejecting rapidly changing voltages on the sensed power rail. For layout, route the two shunt connections as a compact, symmetric pair and minimize the area enclosed by those traces. Place the shunt and amplifier input network close together, use a low-value differential filter only where its added noise and settling behavior are acceptable, and terminate the amplifier output according to the ADC or analog front-end requirements. This page combines the manufacturer lifecycle information, verified distributor records, family-level alternatives, comparison criteria, and application-oriented design guidance for engineers evaluating the INA240A2PW as a current-sense amplifier for industrial and power-conversion systems.

Запрос цены Контакты
INA240A3D - 80V Current Sense Amplifier | Texas Instruments
INA240A3D

INA240A3D - 80V Current Sense Amplifier | Texas Instruments

The Texas Instruments INA240A3D is a bidirectional, ultra-precise voltage-output current-sense amplifier with an operating common-mode range of -4 V to 80 V, enhanced PWM rejection, and an 8-pin SOIC package. It is designed to measure the voltage developed across a shunt resistor in high-side or low-side current-sensing circuits while supporting common-mode voltages above the device supply voltage. A current-sense amplifier is a specialized amplifier within the instrumentation-amplifier and signal-conditioning hierarchy. It converts the small differential voltage produced by a shunt resistor into a proportional analog voltage suitable for measurement by an ADC, MCU, motor controller, or protection circuit. The INA240 family is classified as an analog signal-chain IC and is commonly placed beside a power-conversion stage to create a precision current-feedback signal. The INA240A3D combines bidirectional measurement, a wide -4 V to 80 V common-mode range, and enhanced PWM rejection. Bidirectional operation allows the output polarity to represent either positive or negative current. The negative common-mode capability is useful when a shunt is observed during a below-ground flyback interval, while the upper range supports current monitoring in systems operating well above the amplifier supply voltage. Its stated operating-temperature range is -40 °C to 125 °C. The device uses a voltage-output architecture with reference and supply connections that support system-level current measurement. Because the amplifier can operate independently of the common-mode voltage being sensed, its performance is maintained in applications where the shunt voltage swings rapidly while the amplifier remains powered from a low-voltage rail. This architecture is particularly useful in motor drives, solenoid controls, power converters, and battery-powered systems where a conventional low-voltage current-sense amplifier may leave the measurement range. Typical uses include high-side DC-link monitoring, low-side motor-return measurement, solenoid current diagnostics, power-supply telemetry, and battery charge or discharge current sensing. In these systems, the shunt is placed in the current path and connected to the differential input of the INA240A3D. The resulting analog voltage can be routed to a control ADC or comparator for regulation, fault detection, or data logging. Design the input and reference network carefully because the differential shunt voltage, amplifier supply, output range, and selected shunt resistance jointly determine usable measurement range. Keep the shunt and amplifier connections compact to minimize parasitic pickup, use a Kelvin connection where practical, and route the differential pair away from switching-node copper. The manufacturer's INA240 datasheet should be used for pin assignments, gain, input limits, output behavior, and recommended application values. This page organizes the verified INA240A3D operating limits, package information, sourcing details, replacement constraints, application guidance, and design considerations. It also distinguishes a confirmed same-package automotive alternative from incompatible package or gain variants that cannot be treated as drop-in replacements.

Запрос цены Контакты