Товары (44.000+)

KSZ8721SLI-TR - 10/100 Ethernet PHY | Microchip Technology (Tape & Reel)
KSZ8721SLI-TR

KSZ8721SLI-TR - 10/100 Ethernet PHY | Microchip Technology (Tape & Reel)

Microchip Technology KSZ8721SLI-TR is a single-channel 10/100 Ethernet physical-layer transceiver with a 48-SSOP package, operating from a 2.5 V core and supporting a 3.3 V single-supply application. It provides separate 10Base-T and 100Base-TX/FX physical-medium functions plus MII and RMII host interfaces for transmitting and receiving Ethernet data. The device supports 10 Mbps and 100 Mbps operation and is intended for embedded networking equipment requiring a dedicated Ethernet PHY. An Ethernet physical-layer transceiver, or Ethernet PHY, converts logical digital data into electrical signaling for a physical network medium. The KSZ8721SLI-TR belongs to the integrated-circuit hierarchy physical-layer transceiver > Ethernet interface IC > interface IC. Its 10Base-T capability supports legacy 10 Mbps copper Ethernet, while 100Base-TX/FX supports Fast Ethernet over twisted pair or optical-fiber-compatible links. The MII and RMII interfaces allow a host processor or network controller to connect through either a parallel media-independent interface or the more pin-efficient reduced media-independent interface. Key verified features include full IEEE 802.3 operation, support for 10Base-T, 100Base-TX, and 100Base-FX physical media, and both MII and RMII host connectivity. The KSZ8721 operates its core at 2.5 V to address low-voltage and low-power requirements, while the device is described as a 3.3 V single-supply transceiver. Its 48-SSOP package provides enough pins for separate transmit, receive, management, clock, and host-interface functions. Technically, the KSZ8721SLI-TR consolidates a 10Base-T physical medium attachment function, a 100Base-TX/FX physical medium attachment function, and the associated host-facing digital interface into one package. MII exposes a wider parallel bus, while RMII reduces the number of host-interface signals and is commonly preferred when the connected controller supports it. The manufacturer identifies the KSZ8721 family as a 10BaseT, 100BaseTX, and FX physical-layer transceiver designed for low-power embedded networking. Typical uses include industrial Ethernet controllers, embedded gateways, set-top equipment, printer and scanner interfaces, test equipment, and OEM network appliances. A board designer can connect the KSZ8721SLI-TR to an Ethernet transformer or appropriate fiber interface, provide the required decoupling, and connect it to an MII- or RMII-capable controller. The choice of media interface and magnetics should be based on the required copper or fiber link distance and system compliance targets. A critical design consideration is confirming the controller's MII or RMII timing, clock requirements, reset behavior, and supported media type against the manufacturer datasheet before layout release. Input and output supply rails should be decoupled close to the device, while the copper or fiber network path should be routed according to the selected magnetics and medium requirements. Do not infer unverified pin assignments or timing values from distributor listings alone. This page consolidates verified manufacturer and distributor information, package details, commercially relevant sourcing links, and same-family replacement evidence. It also provides application guidance and comparison context intended to support faster component selection without treating unreported electrical parameters as verified facts.

Запрос цены Контакты
KSZ8765CLXCC - 5-Port Managed Ethernet Switch | Microchip
KSZ8765CLXCC

KSZ8765CLXCC - 5-Port Managed Ethernet Switch | Microchip

Microchip Technology KSZ8765CLXCC is an integrated Layer 2-managed Ethernet switch with four 10/100 Mbps copper ports, one 10/100/1000 Mbps Gigabit uplink, and fiber support in an 80-pin LQFP package measuring 10 x 10 mm. It supports GMII, RGMII, MII, and RMII interfaces, allowing flexible connection to network processors, switching fabrics, and embedded Ethernet equipment. An Ethernet switch is a semiconductor that forwards Ethernet frames between multiple physical ports while reducing the need for separate switching hardware on each link. The KSZ8765 belongs to the managed-switch hierarchy: Ethernet switch, Layer 2 network switch, interface IC, and integrated circuit. Its five-port arrangement combines copper Ethernet connectivity with a gigabit uplink, making it suitable for compact embedded network infrastructure where board area and interface flexibility are important. The primary features include four 10/100 Mbps copper ports, one Gigabit port, integrated 10/100 Base-FX/T/TX PHY support, and both legacy MII/RMII and gigabit GMII/RGMII interfaces. Layer 2 management adds value in access equipment, industrial controls, network appliances, and test systems where individual port configuration, traffic prioritization, or centralized switching behavior can simplify firmware and board design. The combination of MII, RMII, GMII, and RGMII support distinguishes the KSZ8765 from simpler unmanaged Ethernet switches. A host processor can connect through RMII or MII for 10/100 Mbps designs, while GMII or RGMII supports a Gigabit data path. This range of host interfaces permits one switch platform to address multiple processor architectures and clocking arrangements without changing the external Ethernet-port topology. Typical uses include industrial Ethernet gateways, embedded network appliances, communication equipment, test and measurement systems, and access-control infrastructure. The four copper ports support device-to-device links, while the Gigabit port can provide a higher-bandwidth uplink to a router, control processor, or backplane. Fiber-capable operation is useful where longer-distance links or galvanic-isolation requirements make copper unsuitable. PCB design must account for the 10 x 10 mm LQFP footprint, high-speed interface constraints, proper decoupling, and controlled impedance routing for GMII and RGMII links. Review the Microchip reference design and pin-description table to assign power, ground, clocks, management signals, and PHY connections before releasing the layout. This page combines the Microchip product definition, package and interface information, application guidance, and same-family drop-in alternatives. It also highlights the design decisions that matter when moving between temperature-grade variants of the KSZ8765 while retaining the same 80-pin LQFP footprint.

Запрос цены Контакты
KSZ8765CLXIC - 5-Port Managed Ethernet Switch | Microchip
KSZ8765CLXIC

KSZ8765CLXIC - 5-Port Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8765CLXIC is a highly integrated, Layer 2-managed, five-port Ethernet switch for embedded networking systems. It combines four 10/100 Mbps copper ports with one 10/100/1000 Mbps Gigabit uplink, supports 100Base-FX fiber connectivity, and provides configurable GMII, RGMII, MII, and RMII host interfaces. The device is packaged in an 80-lead LQFP measuring 10 mm by 10 mm. An Ethernet switch is a Layer 2 network-semiconductor device that receives Ethernet frames on one port, examines their destination addresses, and forwards traffic to the appropriate port or ports. A managed switch adds configurable status, control, and monitoring functions to this basic forwarding role. The KSZ8765 belongs to the broader hierarchy of Ethernet switch, network interface controller, communications semiconductor, and integrated circuit. Key features include five integrated switch ports, Layer 2 management, 10/100 Mbps copper networking, a Gigabit uplink, and support for both fiber and copper media. Its configurable GMII, RGMII, MII, and RMII interfaces allow it to connect with microcontrollers, network processors, FPGAs, and other Ethernet-capable system controllers. The hardware design checklist identifies Ports 1 and 2 as 100Base-FX fiber ports, Ports 3 and 4 as 10/100Base-T/TX copper ports, and Port 5 as a configurable uplink supporting GMII, RGMII, MII, or RMII. The KSZ8765CLXIC is designed to reduce the component count of embedded Ethernet equipment by combining multiple physical-layer interfaces, switching logic, and management functions in one package. This integration can simplify board partitioning while preserving separate copper and fiber connectivity. Its architecture is particularly useful when an equipment maker needs a managed industrial network interface without implementing five discrete Ethernet PHYs and an external switch controller. Typical uses include industrial Ethernet equipment, factory automation controllers, embedded gateways, telecom access hardware, network appliances, and optical-to-copper network bridges. The device can support equipment that bridges legacy 10/100 Mbps copper links to a faster Gigabit uplink while retaining access to optical ports for longer-distance or electrically isolated links. Designers should follow the Microchip KSZ8765CLX Hardware Design Checklist when assigning the clock, management interface, media-dependent interfaces, power rails, and reset or configuration signals. The complete electrical limits, recommended operating conditions, transceiver details, internal register functions, and signal timing must be taken from the manufacturer datasheet rather than inferred from the product summary. This page combines the manufacturer product description, package and interface facts, pricing-page information, and hardware-design guidance into an application-focused guide. It also distinguishes directly documented characteristics from electrical parameters that require confirmation from the complete KSZ8765 datasheet.

Запрос цены Контакты
KSZ8775CLXCC - 5-Port 10/100 Ethernet Switch | Microchip
KSZ8775CLXCC

KSZ8775CLXCC - 5-Port 10/100 Ethernet Switch | Microchip

The Microchip Technology KSZ8775CLXCC is a highly integrated, Layer 2-managed, five-port Ethernet switch with three 10/100 Mbps copper ports, one RMII port, and a fifth 10/100/1000-capable port in an 80-LQFP package measuring 10 mm by 10 mm. The device supports MII, RMII, RGMII, and GMII interfaces and is designed to reduce system cost in cost-sensitive embedded networking equipment. An Ethernet switch is a semiconductor that connects multiple internal endpoints to an Ethernet network while providing Layer 2 frame forwarding, port management, and media access control. The KSZ8775 belongs to the Ethernet switch hierarchy, combining an Ethernet controller, integrated 10/100Base-T and 10/100/1000Base-T transceiver functions, and flexible serial host interfaces in one package. The principal feature set includes five-port switching, Layer 2 management, three dedicated 10/100 Mbps copper ports, an RMII interface on Port 4, and support for RGMII, GMII, MII, and RMII host connections. Integrating the switch and physical-layer functions reduces the number of discrete components required around a network processor, helping simplify board layout in industrial, communications, and embedded systems. The KSZ8775CLX is positioned as a cost-optimized switching solution rather than a general-purpose host processor. Its configurable digital interfaces allow the same device family to accommodate processors with different media-independent interface requirements. The 80-LQFP package provides 80 external connections for power, clock, management, serial interfaces, copper ports, status indication, and configuration, making careful pin assignment and high-speed layout essential. Typical uses include industrial Ethernet equipment, embedded routers, network appliances, print servers, machine controllers, and communications equipment requiring several copper ports alongside a high-speed processor interface. The integrated 10/100 Mbps copper ports suit legacy 100BASE-TX links, while the additional high-speed port supports designs that need greater uplink bandwidth. Designers should use the manufacturer pin-description table when assigning the 80-LQFP footprint and should keep RMII, RGMII, GMII, and MII clocking and signal-routing requirements under consideration. Differential copper routing, controlled clock topology, solid ground-plane continuity, and compliance-focused magnetics integration are central to achieving reliable Ethernet performance. This product page organizes the manufacturer positioning, exact package information, interface details, replacement-screening constraints, and application guidance into one engineering reference. It also distinguishes verified drop-in replacements from broader functional equivalents so procurement and PCB redesign decisions are based on package and pin compatibility rather than similar Ethernet functionality alone.

Запрос цены Контакты
KSZ8775CLXIC 5-Port 10/100 Ethernet Switch | Microchip
KSZ8775CLXIC

KSZ8775CLXIC 5-Port 10/100 Ethernet Switch | Microchip

The Microchip Technology KSZ8775CLXIC is a highly integrated, Layer 2-managed, five-port 10/100 Ethernet switch with a 3.3 V supply and an 80-pin LQFP package measuring 10 mm by 10 mm. It combines three 10/100 Mbps copper ports, an RMII Port 4 interface, and a flexible Port 5 interface supporting RGMII, GMII, or RMII operation. The switch also provides automatic power saving, wake-up support, and configuration through power-up and reset pins. An Ethernet switch is a network-interface integrated circuit that forwards Ethernet frames between a processor, network interface controllers, and physical-layer devices. The KSZ8775 belongs to the managed-switch hierarchy within Ethernet controllers, interface ICs, and broader networking semiconductors. Its Layer 2 architecture reduces the need for discrete switching components while supporting cost-sensitive embedded, industrial, and communications equipment. The KSZ8775CLXIC's principal advantages include five integrated ports, support for copper links at 10/100 Mbps, and flexible host-facing interfaces on the two upper ports. Its automatic power-saving function helps reduce unnecessary activity in embedded systems, while the wake-up function supports designs that must resume network operation on demand. Power-up and reset configuration provides a deterministic hardware initialization path for systems without a complex manager-boot sequence. Port 4 is identified as an RMII interface, while Port 5 can use RGMII, GMII, or RMII. These selectable interfaces make the device adaptable to processors, FPGAs, and communication controllers with different host-bus requirements. The combination of three copper-facing ports and two configurable upper-port interfaces creates a compact Ethernet switching hub around a single 3.3 V device. Typical applications include industrial Ethernet gateways, embedded control systems, factory equipment, network adapters, communications appliances, and compact embedded Ethernet hubs. The device is especially useful when a design needs several 10/100 copper connections plus one or two processor-facing interfaces without implementing a discrete switching layer. PCB design should preserve pin-compatible placement of the 80-pin LQFP footprint and route each copper-port differential pair according to the manufacturer's layout guidance. Keep the 3.3 V supply and decoupling network close to the device, and provide clean interfaces to the selected processor or FPGA. Because an Ethernet switch integrates high-speed digital links and magnetics-facing circuitry, controlled return paths and disciplined differential-pair routing are central to reliable operation. This page consolidates the device's port configuration, interface options, sourcing information, practical design guidance, and verified drop-in comparison. The 80-pin LQFP outline and 3.3 V operation make the KSZ8775CLXIC a focused choice for compact Layer 2 switching designs that need multiple 10/100 Mbps copper ports and flexible host connectivity.

Запрос цены Контакты
KSZ8794CNXCC - 4-Port 10/100 Managed Ethernet Switch | Microchip
KSZ8794CNXCC

KSZ8794CNXCC - 4-Port 10/100 Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8794CNXCC is a Layer 2 managed Ethernet switch with four 10/100 Mb/s copper ports and a Gigabit RGMII/MII/RMII uplink interface, housed in a 64-pin QFN package measuring 8 mm by 8 mm. Three ports support 10/100 Mb/s Ethernet, while the fourth provides a 10/100/1000 Mb/s Gigabit uplink. The device operates from a 3.3 V supply and combines copper-port PHYs, switching logic, and uplink control in one package. An Ethernet switch is a Layer 2 network component that receives Ethernet frames, examines destination addresses, and forwards traffic through the appropriate physical port. The KSZ8794CNXCC belongs to the managed-switch hierarchy, combining integrated 10/100 Base-T/TX PHYs with management features designed to reduce the component count and board area required for multiport industrial or embedded Ethernet equipment. The principal features are four integrated copper Ethernet ports, a configurable Gigabit uplink, support for RGMII, MII, and RMII host interfaces, internal biasing, and on-chip termination. Its 8 mm by 8 mm QFN-64 package supports compact designs while exposing high-speed network connectivity without requiring four discrete Ethernet PHYs. The managed Layer 2 architecture is suitable for systems that need controlled forwarding behavior rather than only basic hub functionality. The uplink architecture allows a lower-cost 10/100 Mb/s access network to connect to a faster Gigabit backbone through a single high-speed host interface. RGMII supports parallel high-speed signaling, MII is a lower-speed parallel interface, and RMII reduces the number of host-side signals. Designers should select the interface according to the host processor, signal-rate requirements, board constraints, and software-support considerations described in the manufacturer datasheet. Typical uses include industrial Ethernet gateways, factory automation controllers, embedded network appliances, video-network equipment, and compact access switches. The KSZ8794CNXCC is especially relevant when three copper endpoints need 10/100 Mb/s connectivity and a fourth port must provide a Gigabit path to a network processor or switching uplink. Board design requires careful treatment of Ethernet magnetics, termination, supply routing, clocking, and high-speed uplink signals. Place the KSZ8794CNXCC and its decoupling close to the relevant connectors, follow the hardware design checklist for RJ45 termination, and preserve continuous ground references beneath high-speed interfaces. This product summary consolidates the switch configuration, interface options, package information, drop-in-family alternatives, and implementation guidance needed to evaluate the KSZ8794CNXCC before beginning a Layer 2 Ethernet design.

Запрос цены Контакты
KSZ8794CNXIC - 4-Port Managed Ethernet Switch | Microchip
KSZ8794CNXIC

KSZ8794CNXIC - 4-Port Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8794CNXIC is a highly integrated, Layer 2 managed Ethernet switch with three 10/100 Mbps copper ports and one 10/100/1000 Mbps uplink port, housed in a 64-QFN 8 mm by 8 mm package. Its configurable RGMII, MII, and RMII uplink interface supports flexible host connections while the four-port architecture combines copper-port switching with a Gigabit uplink. An Ethernet switch is a semiconductor that connects multiple network endpoints through one uplink to a host, router, or wider network. The managed designation means the KSZ8794 provides Layer 2 switch functions rather than operating only as a basic repeater or hub. Within the networking hierarchy, it combines Ethernet switching, a 10/100BASE-T/TX PHY for copper ports, and a configurable Gigabit serial interface for the uplink. The KSZ8794CNX is intended for cost-sensitive systems requiring three 10/100 Mbps copper ports and one Gigabit uplink. Its integrated design reduces the number of discrete network components required in industrial controllers, residential gateways, embedded equipment, and network appliances. Microchip identifies internal biasing, low power consumption, on-chip termination, and a small package outline as major cost and design benefits. The uplink can operate with RGMII, MII, or RMII, allowing system architects to match the switch to processors, FPGAs, and other Ethernet-capable controllers according to timing, pin-count, and design-complexity requirements. This flexibility is particularly useful when one platform must support several host interfaces or when a product family needs to reuse related switch designs. Typical implementation places the KSZ8794CNX between three copper-connected devices and a higher-speed network uplink. In an industrial controller, the copper ports can connect local sensors, service interfaces, or production equipment while the uplink carries aggregated traffic. In a residential gateway, the same arrangement supports three local Ethernet endpoints and a Gigabit connection to an access network or router. Hardware implementation should follow the KSZ8794CNX Hardware Design Checklist, including guidance on magnetics, termination, layout, and interface implementation. The device also has an associated silicon errata and data-sheet clarification document, so production designs should account for the applicable silicon revision and current manufacturer documentation. This page consolidates the verified switch architecture, interface options, package information, hardware-design guidance, errata context, and sourcing details into an engineering-focused overview. It also identifies which detailed electrical, timing, environmental, and pin-level values require confirmation from the current manufacturer datasheet before schematic release or PCB signoff.

Запрос цены Контакты
KSZ8795CLXCC - 5-Port Managed Ethernet Switch | Microchip
KSZ8795CLXCC

KSZ8795CLXCC - 5-Port Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8795CLXCC is a highly integrated, Layer 2-managed five-port Ethernet switch with four 10/100 Mbps copper ports and one 10/100/1000 Mbps Gigabit uplink port, housed in an 80-lead LQFP package measuring 10 mm by 10 mm. The device combines copper-port switching with Gigabit uplink connectivity for cost-sensitive embedded networking systems. An Ethernet switch is a semiconductor that connects multiple physical-layer network ports to a common switching fabric and forwards Ethernet frames between ports and an uplink processor. The KSZ8795 operates at the Layer 2 data-link level, where frame destination addresses determine the outgoing port. Its managed architecture provides a practical platform for connected industrial, consumer, communications, and embedded equipment requiring several copper Ethernet connections. The KSZ8795's principal features are its four dedicated 10/100 Mbps copper ports, dedicated 10/100/1000 Mbps uplink capability, and support for GMII/RGMII and MII/RMII processor interfaces. These parallel interface options let the switch connect to controllers with different clocking and data-width requirements. Layer 2 management supports controlled network behavior rather than operating solely as an unmanaged frame-forwarding device. The KSZ8795CLXCC is packaged in an 80-lead LQFP, identified by the CLX package code in the manufacturer ordering information. Its 10 mm by 10 mm surface-mount package consolidates five-port switching, a Gigabit uplink, and management functions into one device. The exact pin names, voltage limits, timing limits, clock requirements, and electrical characteristics should be taken from the manufacturer datasheet and hardware design checklist when assigning PCB signals. Typical implementations include industrial Ethernet gateways, IP cameras, building-automation controllers, communications equipment, set-top and media systems, and embedded products that expose several 10/100 ports while retaining a Gigabit connection to a host processor. The four fast ports support legacy 10/100 equipment, while the Gigabit uplink supports higher-bandwidth backhaul or processor traffic. MII, RMII, GMII, and RGMII connectivity allows the switch to be adapted to different embedded Ethernet controller arrangements. PCB implementation requires careful separation of high-speed digital interfaces from copper-port circuitry. Place the KSZ8795CLX hardware design checklist alongside the datasheet, use the recommended magnetic-interface and termination network for each copper port, and observe the package's exposed-pad and thermal-land requirements. The manufacturer checklist specifies RJ45 transmit routing and a 75 ohm, 1000 pF, 2 kV capacitor network for the cable-side center tap, making those details important during layout review. This page organizes the switch's port architecture, interface options, package information, sourcing workflow, and design references into an engineering-focused selection guide. It also identifies why the exact KSZ8795CLXCC ordering code must be reviewed against schematic, PCB, thermal, and firmware requirements rather than substituted solely by port count or headline uplink speed.

Запрос цены Контакты
KSZ8795CLXIC - 5-Port 10/100 Managed Ethernet Switch | Microchip
KSZ8795CLXIC

KSZ8795CLXIC - 5-Port 10/100 Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8795CLXIC is a Layer 2 managed, highly integrated 5-port Ethernet switch with four 10/100BASE-T/TX copper ports and one 10/100/1000BASE-T Gigabit uplink port, delivering configurable GMII, RGMII, MII and RMII host interfaces from an 80-LQFP (10 x 10 mm) package. It operates from a single 3.3 V supply and is offered in an industrial-temperature ordering code. An Ethernet switch is a Layer 2 network device that forwards Ethernet frames between multiple physical ports using a MAC address table. In this device family, the switch also integrates 10/100BASE-T/TX PHYs with internal biasing resistors, on-chip termination and auto-negotiation, so a single silicon device replaces discrete magnetics-heavy copper PHY circuitry. The KSZ8795CLXIC therefore sits in the hierarchy: Ethernet switch > Layer 2 managed switch > integrated copper PHY switch > network interface IC. Key features include four 10/100Mbps copper ports with auto-MDIX support, a Gigabit-capable uplink port, IEEE 802.3u compliant operation, MIIM and SPI management interfaces, and on-chip port termination that eliminates external resistor networks. Low power consumption is achieved through internal biasing rather than external resistor dividers, and the small package outline reduces board area versus discrete implementations. Internally the device combines a five-port frame buffer with an integrated 10/100 MAC/PHY per copper port and a configurable uplink MAC supporting GMII, RGMII, MII and RMII. Management is handled by a MIIM register interface and an SPI host interface, giving the system processor access to VLAN, QoS, port enable and mirror registers. The design is intended for cost-sensitive embedded equipment where a single high-integration switch replaces several discrete PHYs and magnetics. Typical applications include industrial control gateways, industrial Ethernet switches and PLC communication modules, IP cameras and surveillance recorders, industrial IoT and building-automation nodes, and consumer or telecom CPE equipment with a Gigabit uplink. The configurable uplink lets one design serve either RGMII-based application processors or RMII-based microcontrollers. Keep the analog and digital ground pins tied to a single solid, contiguous ground plane. Microchip explicitly warns that splitting GDNA and GNDD into separate planes causes frame drops, so route both to the same uninterrupted system ground and place the port magnetics with short, tightly-coupled differential pairs to preserve return-path integrity. This page combines the manufacturer switch specifications, distributory pricing structure, pin-compatible 80-LQFP alternatives, and practical layout and thermal guidance that you would otherwise have to reconstruct from several separate documents.

Запрос цены Контакты
KSZ8841-16MVLI - 10/100 Ethernet Controller | Microchip
KSZ8841-16MVLI

KSZ8841-16MVLI - 10/100 Ethernet Controller | Microchip

The Microchip Technology KSZ8841-16MVLI is a single-port 10/100 Base-T/TX Ethernet MAC controller with an integrated Fast Ethernet PHY and a generic 16-bit host processor interface. It supports one Ethernet port at 100 Mb/s, uses a 128-lead LQFP package measuring 14 x 14 mm, and includes Wake-on-LAN functionality for remotely waking compatible systems. An Ethernet MAC controller is a network interface integrated circuit that manages frame transmission, reception, addressing, and the connection between a host processor and an Ethernet physical layer. The KSZ8841 belongs to the Ethernet controller hierarchy, which combines a MAC controller, 10/100 Base-T/TX PHY, and a generic host-bus interface in a single mixed-signal device. This integration reduces external components and simplifies the relationship between the processor bus and an RJ45 network connection. The KSZ8841 supports 8-bit, 16-bit, and 32-bit generic host-processor interfaces. The -16MVLI configuration uses a 16-bit interface, while its dynamic memory pointer maintains a 4-byte buffer boundary for host-memory transfers. A dedicated integrated PHY provides 10/100 Base-T/TX operation, while Wake-on-LAN support addresses power-conscious embedded systems that must respond to remote network activity. The controller combines digital frame-processing logic with analog Ethernet transceiver circuitry. Its host interface provides a direct path between the Ethernet MAC and processor-managed memory, reducing the need for a separate Ethernet interface component. In systems requiring wider bus bandwidth, the related 32-bit controller option can move data in wider transactions, although the exact memory-transfer rate still depends on processor timing, wait states, and the physical interface implementation. Typical uses include industrial embedded controllers, factory automation equipment, print servers, set-top boxes, embedded servers, and network-enabled data-acquisition systems. In an industrial controller, the device can connect an embedded processor to a 10/100 network while supporting remote wake-up for maintenance systems. In compact embedded products, integrating the PHY and MAC into one package reduces board area compared with a discrete MAC and external transceiver arrangement. PCB design should preserve the Ethernet magnetics and high-speed signal path, provide the decoupling and grounding specified by the manufacturer datasheet, and keep the processor-bus traces short. The 128-LQFP footprint requires careful escape routing because the generic host interface uses many pins. Confirm the complete pin assignment, voltage requirements, clocking, and reset behavior against the manufacturer pin-description table before routing the board. This product page combines the manufacturer interface description, verified ordering information, package details, and practical selection guidance. It also organizes pin, replacement, application, and sourcing questions around the distinctions that matter when integrating this Ethernet controller into a new embedded design.

Запрос цены Контакты
KSZ8841-32MVLI - 10/100 Ethernet Controller | Microchip
KSZ8841-32MVLI

KSZ8841-32MVLI - 10/100 Ethernet Controller | Microchip

The Microchip Technology KSZ8841-32MVLI is a single-port Ethernet MAC controller with an integrated 10/100 Base-T/TX PHY and a generic 32-bit host-bus interface, housed in a 128-LQFP 14 x 14 mm package. It combines Ethernet media-access control, physical-layer signaling, and host-interface functions in one integrated circuit for compact industrial networking equipment. An Ethernet MAC controller is an interface IC that manages frame transmission and reception between a processor and an Ethernet network. The associated PHY converts between digital Ethernet symbols and signals carried by twisted-pair cabling. Together, a MAC controller and PHY form the hardware boundary between a digital embedded system and a 10/100 Base-T network, reducing the number of discrete components required for an Ethernet port. The KSZ8841-32MVLI provides a generic 32-bit bus interface rather than the PCI interface used by the PCI version of the KSZ8841 family. This makes it suitable for embedded processors, industrial controllers, and other systems that can connect through a parallel host bus. Its integrated 10/100 Base-T/TX PHY supports connection to standard 10/100 Ethernet networks through the appropriate magnetics and external circuit implementation described by the manufacturer. The device is offered in a 128-LQFP package measuring 14 x 14 mm, providing many external signal connections for host-bus control, data, clocks, interrupts, power, and Ethernet physical-layer functions. The manufacturer classifies the KSZ8841 series as a family of single-port controllers with both PCI and non-PCI CPU-interface options. The 32MVLI ordering code identifies the non-PCI, generic 32-bit-interface configuration. Typical uses include industrial Ethernet gateways, embedded control systems, programmable logic controller communications, instrumentation equipment, and compact network adapters. The integrated MAC/PHY architecture simplifies the hardware and software boundary for a connected embedded product, while the parallel host interface provides a direct path between the Ethernet engine and a microprocessor or other bus master. Designers should follow the manufacturer reference design when assigning the generic host-bus signals, supplying the required clocks and decoupling, and implementing the Ethernet magnetics and analog network interface. Clock timing, signal-integrity practices, and controlled board layout are particularly important because the LQFP exposes numerous high-speed digital and Ethernet-related connections. This product overview consolidates the verified device classification, interface configuration, package information, sourcing data, comparison points, and implementation guidance. It also distinguishes genuine same-footprint alternatives from related parts with different bus widths so engineers can evaluate PCB reuse without relying on family-name similarity alone.

Запрос цены Контакты
KSZ8841-PMQL - 10/100 Ethernet PCI Controller | Microchip
KSZ8841-PMQL

KSZ8841-PMQL - 10/100 Ethernet PCI Controller | Microchip

The Microchip Technology KSZ8841-PMQL is a single-port Fast Ethernet MAC controller with a 32-bit, 33 MHz PCI processor interface, supplied in a 128-pin PQFP package measuring 14 x 20 mm. It combines an IEEE 802.3u-compatible 10/100 Base-T/TX Ethernet controller with a host-bus interface intended for PCI-based embedded systems. The controller integrates the Ethernet MAC function with the physical-layer interface needed for a single 10/100 network port. An Ethernet MAC controller is an interface integrated circuit that manages frame transmission and reception between a computing host and an Ethernet network. The MAC layer identifies network frames and handles access to the communications medium, while the integrated Fast Ethernet physical interface connects that logical function to twisted-pair cabling. In the system hierarchy, the KSZ8841-PMQL belongs to the class of Ethernet interface controllers and network interface integrated circuits used within embedded networking equipment. The KSZ8841-PMQL provides one 10/100 Base-T/TX port, a 32-bit PCI interface, and a stated PCI operating frequency of 33 MHz. Its IEEE 802.3u compatibility identifies the intended Fast Ethernet protocol generation. The device is also associated with a non-PCI member of the KSZ8841 series, KSZ8841-MQL, which uses a different CPU interface and therefore requires a different host-side design rather than being a universal substitute. The PCI host interface provides a parallel processor-facing path for moving Ethernet frames between the controller and an embedded PCI system. This makes the device appropriate for legacy or industrial embedded platforms that retain PCI infrastructure but require an integrated 10/100 Ethernet connection. The 128-PQFP package also provides a substantial pin count for the MAC, PCI, clock, reset, power, and physical-network functions represented by this controller. Typical applications for the KSZ8841-PMQL include PCI-based industrial controllers, embedded communication equipment, network interface adapters, and legacy embedded systems requiring 10/100 Base-T/TX connectivity. The controller can also serve as the foundation for custom PCI network-interface subsystems where a dedicated Ethernet MAC is required instead of a higher-complexity system-on-chip. Designers should distinguish the standard KSZ8841-PMQL from the industrial-temperature KSZ8841-PMQLI version when selecting the correct ordering code. PCB implementation must follow the manufacturer's 128-pin PQFP pinout and recommended layout guidance, including correct termination, clocking, reset sequencing, and Ethernet physical-layer routing. This product page combines the manufacturer identification, package information, interface details, comparison candidates, and application guidance needed to evaluate the KSZ8841-PMQL. Request a Quote on this page for current commercial availability, lead time, and supporting documentation.

Запрос цены Контакты
KSZ8842-PMBL - 2-Port 10/100 Ethernet Switch | Microchip
KSZ8842-PMBL

KSZ8842-PMBL - 2-Port 10/100 Ethernet Switch | Microchip

The Microchip Technology KSZ8842-PMBL is a two-port 10/100 Base-T Ethernet switch with a generic 32-bit, 33 MHz PCI processor interface, supplied in a 100-LFBGA 9 x 9 mm package. It provides two integrated 10/100 Ethernet ports, an integrated DMA engine, managed Layer 2 switching, and low-power operation for embedded networking equipment. An Ethernet switch is a network-semiconductor device that connects multiple physical network nodes while forwarding Ethernet frames according to Layer 2 addresses. The KSZ8842 belongs to the Ethernet switch hierarchy and integrates physical-layer transceivers, frame processing, port management, and a host-facing peripheral bus within one IC. Its PCI interface allows a processor or embedded controller to configure the switch, manage traffic, and exchange data with the connected Ethernet ports without requiring a separate external Ethernet controller. The manufacturer datasheet identifies the KSZ8842-PMQL/PMBL as the first fully managed two-port switch with a 32-bit, 33 MHz PCI processor interface. The device is compliant with IEEE 802.3u, supports 10/100 Base-T networking, and includes an integrated DMA engine for efficient host data movement. Its four-generation integrated Layer 2 switch architecture supports managed switching functions while reducing the component count of embedded Ethernet designs. The KSZ8842-PMBL is intended for compact PCI-based embedded systems where two Ethernet links are needed close to the host processor. Typical signal paths include industrial control equipment, embedded servers, communication appliances, test systems, and PCI expansion products. A 122 mA supply current value is identified for this device, making system-level power budgeting important when two ports operate continuously. The principal design consideration is the 100-LFBGA footprint. The board must provide the exact ball layout defined by the manufacturer package drawing and must accommodate the PCI, clock, power, reset, and Ethernet magnetics interfaces. Review the ordering information and pin-description tables in the manufacturer datasheet before assigning ball assignments or preparing the PCB footprint. The KSZ8842-PMBL is also the base commercial-temperature ordering code within the PMQL/PMBL PCI-interface family. The PMBL suffix identifies the LFBGA package, while the PMQL suffix identifies a different package. Industrial-temperature ordering variants include the -AM designation; verify the exact suffix, grade, and shipping configuration when substituting parts. This product page consolidates the known switch, interface, package, and ordering information with engineering-focused application guidance, replacement considerations, and a parameter comparison. It also distinguishes electrical or temperature-grade alternatives from packaging-only order codes so engineers can assess PCB compatibility before redesigning an existing LFBGA design.

Запрос цены Контакты
KSZ8842-PMQL - 2-Port 10/100 PCI Ethernet Switch | Microchip
KSZ8842-PMQL

KSZ8842-PMQL - 2-Port 10/100 PCI Ethernet Switch | Microchip

Microchip Technology KSZ8842-PMQL is a fully managed two-port 10/100 Ethernet switch with a generic 32-bit, 33 MHz PCI processor interface, housed in a 128-pin PQFP package measuring 14 mm by 20 mm. The device provides two integrated Fast Ethernet ports, an integrated DMA engine, and low-power operation for PCI-based embedded networking designs. An Ethernet switch is a Layer 2 network device that forwards Ethernet frames between connected nodes while using MAC-address learning to reduce unnecessary traffic. Within the network hierarchy, the KSZ8842-PMQL is an Ethernet interface IC and network interface controller that connects a PCI host processor to two 10/100 Base-TX ports. Its managed-switch architecture supports centralized port control, status monitoring, and traffic management in embedded industrial, communications, and legacy PCI systems. Key features include two integrated 10/100 Ethernet ports, a 32-bit PCI interface operating at 33 MHz, IEEE 802.3u compliance, an integrated DMA engine, and a low-power operating design. The PQFP package provides 128 accessible package positions and uses leaded technology for compatibility with established PCI motherboard and embedded-controller assemblies. An industrial-temperature ordering option, KSZ8842-PMQLI, extends the family for applications requiring extended temperature operation. Architecturally, the KSZ8842-PMQL belongs to the KSZ8842 fourth-generation integrated Layer 2 switch family. Separate PCI and non-PCI implementations allow designers to match the host interface to the platform, while the PMQL version retains the 32-bit PCI processor connection. The integrated DMA engine assists efficient packet transfer between the PCI host and switch ports, reducing the processing burden associated with moving Ethernet traffic through host memory. Typical applications include PCI-based industrial controllers, embedded communications appliances, test and measurement systems, legacy PCI server equipment, and custom network interface cards. The device is particularly suitable when two copper Ethernet ports are required without adding an external two-port switch. Designers must also verify the host platform's supported PCI electrical characteristics, bus width, clocking, and software configuration model before releasing a new design. For a new design, route each differential Ethernet pair through a controlled-impedance layout, keep the PHY and magnetics interface routing compact, and follow the manufacturer's reference layout for power, ground, reset, and clock connections. Because this is a legacy PCI bridge with a large leaded package, confirm long-term sourcing and lifecycle status with Microchip before committing to high-volume production. This page combines the exact manufacturer and distributor identification for KSZ8842-PMQL with package, interface, application, and procurement guidance. It also distinguishes the PCI implementation from related non-PCI KSZ8842 members and identifies the temperature-graded PMQLI counterpart for industrial design reviews.

Запрос цены Контакты
KSZ8851-32MQLI - 10/100 Ethernet Controller | Microchip
KSZ8851-32MQLI

KSZ8851-32MQLI - 10/100 Ethernet Controller | Microchip

Microchip Technology KSZ8851-32MQLI is a single-port 10/100 Base-T Ethernet MAC controller with an integrated PHY and a generic 32-bit parallel CPU interface. The device operates from a 3.1 V to 3.5 V core supply and is packaged in a 128-pin PQFP measuring 14 mm by 20 mm. It is intended for embedded systems that require economical, high-throughput Ethernet connectivity without PCI. An Ethernet MAC controller is an interface integrated circuit that manages frame handling and connects a processor or other bus-based host to an Ethernet physical layer. The KSZ8851 combines the MAC, a 10/100 Base-T/TX PHY, LED indication, wake-up functionality, and a low-power operating mode in one device. Within the semiconductor hierarchy, it belongs to the Ethernet controller and network-interface IC class rather than a general-purpose processor or standalone Ethernet transceiver. The -32MQLI configuration provides a 32-bit non-PCI host interface, making it suitable for embedded processors that can accommodate a wide parallel bus. The 10/100 capability supports legacy Fast Ethernet networks, while the integrated PHY reduces the external component count compared with separate MAC and PHY implementations. Programmable LED indication supports simplified link, activity, and speed-status reporting, and the documented wake-up and low-power features can improve system responsiveness and energy behavior. The KSZ8851 family is offered in 32-, 48-, and 128-pin packages, allowing the same controller family to address different host-interface and board-space requirements. This specific 128-pin PQFP variant provides a conventional parallel-bus connection to the embedded CPU while keeping the Ethernet MAC and physical-layer functions together. Microchip describes the family as a cost-effective solution for adding Ethernet to traditional embedded systems. Typical uses include industrial controllers, embedded data loggers, factory equipment, building-automation gateways, and network-accessible test instruments. In these systems, the host processor can exchange Ethernet frames through the generic 32-bit bus while the controller handles the physical 10/100 link. Systems requiring additional network ports can pair it with a managed Ethernet switch or multi-port PHY while retaining a conventional processor-centric architecture. PCB design should account for the 128-pin PQFP footprint, controlled-impedance signal routing for the parallel host bus, and separation between high-speed digital signals and the Ethernet magnetics and network-side routing. Follow the manufacturer’s reference schematic, component values, and layout guidance in datasheet DS00002425B. The system designer must also verify clock, reset, interrupt, PHY, and power-supply requirements against the complete device pin-description table before releasing the PCB. This product page combines the manufacturer family description with distributor package information, sourcing guidance, application analysis, and engineering design notes. It also distinguishes the exact 32-bit industrial-temperature ordering code from related family members so that engineers can review footprint, interface width, and qualification requirements before committing a design to the PCB.

Запрос цены Контакты
KSZ8851SNL - 10/100 Ethernet Controller | Microchip
KSZ8851SNL

KSZ8851SNL - 10/100 Ethernet Controller | Microchip

The Microchip Technology KSZ8851SNL is a single-port 10/100 Ethernet controller with a 3.3 V SPI interface, integrated 10/100BASE-T/TX PHY, and Media Access Controller in a 32-pin QFN package measuring 5 mm x 5 mm. It provides 10 Mbps and 100 Mbps Ethernet connectivity for embedded systems using a host microcontroller equipped with an SPI interface. The device also includes one copper port and one uplink port, making it suitable for industrial, communications, building-automation, and networked embedded-control equipment. An Ethernet controller is an interface IC that integrates network-frame handling with physical-layer signaling. The KSZ8851 family combines the PHY and MAC with an SPI host interface, reducing the number of external components required to add wired Ethernet to a microcontroller-based product. This integration places the KSZ8851 within the hierarchy of Ethernet controller, network interface controller, interface IC, and semiconductor. Its SPI host interface supports a compact connection to embedded processors while preserving an independent Ethernet data path. The principal verified features are 10/100BASE-T/TX operation, a 3.3 V supply as identified by the distributor specification snippet, and a 32-pin lead-free QFN package. The integrated controller architecture simplifies firmware and hardware compared with a separated Ethernet MAC and external PHY arrangement. A single-port design also keeps board area and component count controlled, which is valuable in embedded products where connector placement, enclosure volume, and system cost are constrained. Technically, the KSZ8851SNL separates host access from Ethernet processing through its Serial Peripheral Interface. The SPI interface provides a compact communication path for register access, configuration, interrupt handling, and Ethernet data transfer. The integrated PHY handles the physical signaling required for 10/100BASE-T/TX copper networking, while the MAC performs the higher-level frame-processing functions required to present Ethernet traffic to the host processor. Typical applications include industrial Ethernet gateways, building-automation controllers, serial-to-Ethernet equipment, embedded test systems, HMI platforms, and network-connected sensors. It is also appropriate for custom industrial control equipment requiring a dedicated Ethernet port without allocating a high-performance host processor for basic Ethernet connectivity. The 5 mm x 5 mm QFN package supports compact designs, although exposed-pad layout and thermal management remain PCB-level concerns. Designers should follow Microchip's KSZ8851SNL Hardware Design Checklist for power, decoupling, magnetics, differential routing, and copper interface implementation. SPI trace integrity, grounding, and isolation requirements must be reviewed alongside the Ethernet physical layer because the controller is intended for copper-connected industrial networks rather than direct cable attachment without supporting network hardware.

Запрос цены Контакты
KSZ8851SNLI - 10/100 Ethernet SPI Controller | Microchip
KSZ8851SNLI

KSZ8851SNLI - 10/100 Ethernet SPI Controller | Microchip

The Microchip Technology KSZ8851SNLI is an industrial-temperature-grade, single-port Fast Ethernet controller integrating a 10/100BASE-T/TX physical-layer transceiver, a Media Access Controller, and a Serial Peripheral Interface in a 32-QFN (5x5 mm) package. It connects a host microcontroller with an SPI interface to copper Ethernet and supports the 10 Mbps and 100 Mbps transfer rates of Fast Ethernet. A Fast Ethernet controller is a network-interface semiconductor that combines physical-layer signaling and higher-level frame processing. Within the product hierarchy, the KSZ8851SNLI is an Ethernet controller interface IC with an integrated Ethernet PHY and MAC. Its SPI host interface provides a practical way to add wired network connectivity to embedded systems without requiring a parallel host bus or a dedicated Ethernet processor. Key device features include a single Ethernet port, integrated 10/100BASE-T/TX PHY, integrated MAC, and an SPI interface. The manufacturer documentation identifies 3.3 V as the main supply and provides 1.8 V, 2.5 V, and 3.3 V options for VDD I/O, allowing the digital interface voltage to be matched more closely to the host microcontroller. The SNLI designation identifies the industrial-temperature-grade version of the KSZ8851SNL family. The KSZ8851SNL family supports SPI, 8-bit, 16-bit, and 32-bit non-PCI CPU interfaces, with package options of 32, 48, and 128 pins. The 32-QFN KSZ8851SNLI is therefore the SPI-oriented option for compact embedded equipment. Integrating the PHY and MAC reduces the number of external Ethernet interface functions required, while the SPI connection limits host-side wiring and allows a microcontroller to manage registers and network traffic through a serial interface. Typical uses include industrial monitoring, networked sensors, building controls, embedded access equipment, and compact gateway products. For these systems, the device can provide a single 10/100 copper port while the host handles application traffic, configuration, and network management. A board design must still provide the required magnetic interface, termination, reference circuitry, clocking, supply rails, and controlled-layout implementation described by the manufacturer hardware checklist. Designers should evaluate the SPI clock and signal-integrity requirements, power-supply sequencing, and Ethernet magnetics together rather than treating the controller as a stand-alone Ethernet jack interface. The 3.3 V supply and selectable 1.8 V, 2.5 V, or 3.3 V VDD I/O levels are important for host compatibility, while the compact 5x5 mm QFN footprint requires a land pattern and thermal strategy appropriate for a leadless package. This page combines the manufacturer identification, SPI and 10/100 Ethernet capabilities, verified-source links, and practical engineering guidance. It also distinguishes the directly documented same-family option from cross-package Ethernet devices, helping engineers make a footprint-aware choice without treating every Ethernet PHY as a drop-in replacement.

Запрос цены Контакты
KSZ8863FLL - 3-Port 10/100 Managed Ethernet Switch | Microchip Technology
KSZ8863FLL

KSZ8863FLL - 3-Port 10/100 Managed Ethernet Switch | Microchip Technology

The Microchip Technology KSZ8863FLL is a highly integrated three-port 10/100 managed Ethernet switch with integrated PHYs, one 100BASE-FX fiber port, one 10/100BASE-TX copper port, and one additional 10/100 port. It supports 10/100 Mbps Ethernet switching, MII connectivity, and CPU control through I2C or SPI. The device is packaged in a 48-LQFP package measuring 7 mm by 7 mm. According to the verified product description, the KSZ8863FLL is intended for low-port-count, cost-sensitive, and power-efficient 10/100 Mbps switch systems. An Ethernet switch is a networking semiconductor that connects multiple Ethernet endpoints and forwards frames between ports using integrated physical-layer transceivers, or PHYs. The managed-switch category adds configuration and control functions beyond basic frame forwarding, including port management, VLAN support, QoS priority handling, and CPU-controlled data interfaces. The KSZ8863FLL belongs to the switch-on-a-chip family, combining multiple Ethernet ports and management functions into one device rather than requiring separate discrete PHY and switch components. Key verified features include a three-port architecture, integrated PHYs, 100BASE-FX fiber support, 10/100BASE-TX copper networking, one MII interface, and CPU control and data interfaces. The product is identified by DigiKey as an Ethernet Switch with a 1.8 V, 2.5 V, or 3.3 V supply option and a 48-LQFP 7 x 7 mm package. Microchip describes the KSZ8863 family as supporting switch management, port and tag-based VLAN, QoS priority, and CPU control, which makes it suitable for compact embedded-network equipment. The KSZ8863FLL is positioned for industrial, communications, and embedded Ethernet designs that need copper and fiber connectivity in a small package. Its integrated approach can reduce board-level component count and simplify the network architecture compared with a discrete switch implementation. The MII interface allows connection to a host processor or another Ethernet-compatible controller, while I2C or SPI management access supports configuration from a microcontroller or embedded system. Designers should verify the exact pinout, transceiver requirements, clocking, magnetics, and fiber-interface implementation against the manufacturer datasheet before layout. Although the MLL, FLL, and RLL variants belong to the same KSZ8863 family, their supported interfaces and features differ, so substitution must be checked carefully. The verified data does not provide complete electrical limits, pin names, or pricing, and those values are marked as needed rather than estimated. This page combines the verified KSZ8863FLL product identity, package information, application positioning, and datasheet references with practical selection guidance. It also distinguishes direct family substitutions from broader Ethernet-switch alternatives that may require PCB, firmware, or interface changes.

Запрос цены Контакты
KSZ8863FLLI - 3-Port 10/100 Managed Ethernet Switch | Microchip Technology
KSZ8863FLLI

KSZ8863FLLI - 3-Port 10/100 Managed Ethernet Switch | Microchip Technology

The Microchip Technology KSZ8863FLLI is a highly integrated 3-port 10/100 managed Ethernet switch with fiber support, packaged in a 48-LQFP 7x7 mm package. It is designed for cost-sensitive, power-efficient low-port-count network systems and provides integrated 10/100 Ethernet PHYs with I2C and SPI control interfaces. The device supports 10 Mbps and 100 Mbps data rates and is identified as a 3-port Ethernet switch controller with Base-FX/T/TX PHY functionality. An Ethernet switch controller is an interface IC that integrates multiple physical-layer transceivers and switching logic into one device. It sits within the hierarchy of Ethernet interface ICs, network controllers, semiconductors, and broader communications equipment. By combining copper and fiber-oriented connectivity in a compact package, the KSZ8863 family is intended to reduce external component count in embedded gateways, industrial controllers, access equipment, and compact network appliances. The KSZ8863FLLI includes support for optical fiber, cable diagnostics, programmable LED indication, and a low-power operating mode. Its managed-switch architecture supports controlled network segmentation and status indication, while the integrated PHYs simplify connections to 10/100BASE-T and fiber-capable downstream equipment. The I2C and SPI interfaces provide host access for configuration and management functions. According to the manufacturer product description, the KSZ8863 series is cost-sensitive, power efficient, and optimized for low-port-count switching systems. The family variants use different suffix options to address product and ordering requirements while retaining a closely related 3-port 10/100 managed-switch architecture. The KSZ8863FLLI is supplied in a 48-LQFP package, enabling conventional surface-mount assembly in industrial and embedded equipment. Its operating temperature range is specified as -40°C to +85°C, making it suitable for extended industrial environments. The 100 Mbps data rate and fiber support distinguish it from basic single-port Ethernet PHY devices. Typical applications include industrial Ethernet gateways, serial-to-Ethernet equipment, access-point controllers, factory automation nodes, and compact embedded network appliances. Because the device combines managed switching, integrated PHYs, programmable LEDs, and low-power operation, it can simplify board design where a small network topology must operate without a discrete switch and multiple PHY packages. The main design consideration is power and signal integrity: place the device and its decoupling network according to the manufacturer reference layout, keep high-speed traces controlled, and validate Ethernet magnetics or fiber interfaces in the final board design. Also confirm the exact fiber, LED, and management configuration for the selected KSZ8863 variant before production release. This product page combines the verified manufacturer and distributor information, identifies package and interface details, and provides practical guidance for Ethernet switch design, sourcing, and qualification. The documented alternatives are organized by manufacturer priority and intended for engineering comparison rather than as automatic substitutions without footprint and configuration verification.

Запрос цены Контакты
KSZ8863MLL 3-Port 10/100 Managed Ethernet Switch | Microchip
KSZ8863MLL

KSZ8863MLL 3-Port 10/100 Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8863MLL is a highly integrated 3-port 10/100 Mbps managed Ethernet switch with integrated PHYs, one MII interface, and CPU control, supplied in a 48-lead LQFP package. It is designed for compact, cost-sensitive, power-efficient 10/100BASE-T networks. The KSZ8863MLL combines two copper Ethernet PHYs supporting 10BASE-T and 100BASE-TX with a third port that can operate through the MII interface or bypass mode. An Ethernet switch IC is a network-interface device that connects multiple Ethernet nodes through integrated PHYs and internal switching logic. The KSZ8863MLL belongs to the Ethernet switch family, which sits within network interface semiconductors and broader embedded communication systems. Its managed-switch features include port- and tag-based VLAN support, QoS priority, link management, and CPU-controlled configuration through I2C or SPI. These capabilities make it suitable when a design needs more deterministic LAN behavior than an unmanaged switch provides. The MLL variant is intended for 2.5 V and 3.3 V systems and supports 10BASE-T and 100BASE-TX operation on two PHY ports. The third port includes an MII interface for connection to a host processor or another Ethernet controller. The supplied product information identifies the device as a 48-LQFP (7x7 mm) part with a 48-pin package and a 100 Mbps Ethernet switch classification. The KSZ8863MLL is useful in industrial embedded systems, compact controllers, factory equipment, and network appliances where three Ethernet paths are needed without implementing a full-size switching ASIC. Its small package and integrated PHYs reduce external PHY count and simplify board design. Configuration can be handled through the CPU interface, while VLAN and QoS features help organize traffic and improve network behavior. Designers should follow the manufacturer datasheet and hardware design checklist for pin assignments, reset timing, clock requirements, magnetic-component selection, and power sequencing. The reset input is active-low, and a hardware reset is required after power-up according to the KSZ8863MLL hardware design checklist. Board layout, magnetics isolation, impedance-controlled traces, and bypass-capacitor placement are critical because Ethernet interfaces are sensitive to return-path and signal-integrity issues. This page combines the verified manufacturer product information, distributor identification, package details, pricing reference, and practical design guidance for engineers evaluating the KSZ8863MLL. It is intended to help determine whether this 3-port Ethernet switch fits a specific embedded networking design before consulting the complete manufacturer documentation.

Запрос цены Контакты
KSZ8863MLLI - 3-Port 10/100 Managed Ethernet Switch | Microchip
KSZ8863MLLI

KSZ8863MLLI - 3-Port 10/100 Managed Ethernet Switch | Microchip

The Microchip Technology KSZ8863MLLI is a highly integrated, three-port managed Ethernet switch with 10/100 Mbps support, I2C and SPI host interfaces, one MII interface, and fiber support in a 48-pin LQFP package measuring 7 mm by 7 mm. It is designed for compact, cost-sensitive, and power-efficient networking systems. An Ethernet switch is a semiconductor that connects multiple local network nodes and manages traffic between network ports. This device belongs to the managed Ethernet switch hierarchy, where integrated PHYs, a switching fabric, and host-register control support small embedded networks without requiring a discrete Ethernet switch design. The KSZ8863 family combines copper and fiber connectivity options in a small package. Three integrated 10/100 Mbps ports support low-port-count network designs, while auto-negotiation follows Clause 28 of the IEEE 802.3u specification. That protocol lets connected devices select a common operating mode. I2C and SPI interfaces provide host access to device functions, while the MII interface supports connection to an external network controller. Advanced power management is specifically identified as a family feature for reducing system power consumption. The KSZ8863MLLI is one of three internal-bonding configurations designated MLL, FLL, and RLL. Microchip states that these configurations are not interchangeable because their internal bonding differs and the mode cannot be changed through an external pin or register setting. The selected configuration therefore remains a manufacturing and design-selection decision rather than a runtime configuration option. Typical uses include industrial Ethernet control, embedded gateways, industrial equipment networking, compact network switches, and systems that need a managed three-port Ethernet switch with copper or fiber uplink support. The 48-LQFP construction is suitable for conventional surface-mount PCB assembly rather than the very smallest leadless packages. Designers should treat the MLL suffix as functionally significant, preserve the manufacturer's recommended decoupling and clock circuitry, and route high-speed Ethernet and MII signals with controlled impedance. Before layout release, use the manufacturer pin-description table and application schematic to assign all 48 pins, especially power, ground, reset, management, PHY, and media-interface signals. This page organizes the KSZ8863MLLI's verified switching, interface, packaging, and compliance characteristics, clarifies why the MLL, FLL, and RLL variants cannot be substituted, and provides practical application guidance for engineers designing compact managed Ethernet equipment.

Запрос цены Контакты
KSZ8863RLL - 3-Port 10/100 Ethernet Switch | Microchip
KSZ8863RLL

KSZ8863RLL - 3-Port 10/100 Ethernet Switch | Microchip

The Microchip Technology KSZ8863RLL is a cost-sensitive, power-efficient, highly integrated three-port 10/100 managed Ethernet switch with integrated PHYs and fiber support. The device is available in a 48-LQFP 7x7 mm package and is configured through I2C or SPI interfaces, as identified by the distributor listings and manufacturer product information. It is intended for low-port-count Ethernet systems requiring integrated copper and fiber connectivity. An Ethernet switch is a network-interface semiconductor that receives Ethernet frames on one port and forwards them to another port using address-based learning. The 10/100 designation refers to support for 10 Mbps and 100 Mbps Ethernet rates, while the three-port architecture consolidates multiple physical-layer connections into one device. In the system hierarchy, the KSZ8863RLL is an Ethernet interface IC, a network interface controller, and ultimately a communications semiconductor. The verified product information identifies the KSZ8863 family as a managed Ethernet switch with integrated 10/100 PHYs, I2C and SPI configuration interfaces, and fiber support. These capabilities allow a compact product to combine several network ports without requiring a separate switch controller and individual PHY devices. Its three-port organization is useful in industrial, embedded, communications, and edge-network equipment where a small number of Ethernet links must be managed efficiently. The KSZ8863RLL uses a 48-LQFP package measuring 7x7 mm according to the distributor listing. Package-level power, temperature, clock, and Ethernet-magnetics requirements must be confirmed in the manufacturer datasheet and KSZ8863RLL Hardware Design Checklist. Those documents are especially relevant to differential trace routing, magnetic-component placement, supply decoupling, and the reference-clock circuit. Typical deployments include three-port industrial Ethernet controllers, embedded network gateways, compact PLC communication modules, factory-floor connectivity, and OEM equipment requiring copper plus optional fiber links. The managed-switch architecture also makes the device suitable for systems that need more controlled network segmentation than an unmanaged repeater provides. For PCB implementation, preserve the pin assignments and reference-clock layout recommended by Microchip. The hardware checklist identifies pin 10 as the clock-circuit output and requires a capacitor to ground, while crystal, stray-capacitance, and load-capacitance values must be selected together. Ethernet magnetics, controlled-impedance routing, grounding, and isolation also require careful validation in the final board design. This page consolidates verified product identity, package information, pricing data, family substitutions, and practical hardware-design guidance. It also distinguishes documented KSZ8863 variants from unsupported replacement claims, helping engineers evaluate compatibility without treating every similar Ethernet switch as a true pin-to-pin substitute.

Запрос цены Контакты
KSZ8863RLLI - 3-Port 10/100 Switch w/ RMII | Microchip
KSZ8863RLLI

KSZ8863RLLI - 3-Port 10/100 Switch w/ RMII | Microchip

The Microchip Technology KSZ8863RLLI is a highly integrated 3-port 10/100 managed Ethernet switch with PHYs, supporting one RMII interface and packaged in a 48-pin LQFP (7x7 mm) for industrial temperature operation. It delivers 100 Mbps data rate per port, integrates three 10/100BASE-TX PHYs with on-chip termination, and provides a non-PCI CPU interface via I2C or SPI to a host processor. The device targets cost-sensitive, power-efficient industrial and embedded networking designs that need a small footprint, low port count managed switch. A managed Ethernet switch is a Layer 2 network device that uses a switch fabric to forward Ethernet frames between connected ports based on MAC address tables, while providing management features such as VLAN, QoS, port mirroring, and rate limiting. The KSZ8863RLLI sits in the hierarchy: Ethernet switch -> managed switch -> Layer 2 switch -> networking IC -> semiconductor. It is part of the IEEE 802.3 / 802.3u family of Fast Ethernet devices, supporting auto-negotiation per Clause 28 of the IEEE 802.3u specification. Key features include integrated 10/100BASE-TX PHYs with HP auto-MDI/MDIX (no external magnetics on the PHY side), support for fiber mode on Port 3, an RMII interface to an external MAC or host, an I2C/SPI host management interface, advanced power management including energy-detect mode, and 1.4 KB packet buffer per port. The device operates from -40C to +85C industrial temperature range. Architecture is built on a store-and-forward switch fabric with 1 Gbps total bandwidth, supporting wire-speed non-blocking forwarding on all three ports. The device includes IEEE 802.1Q VLAN, 802.1p QoS priority queues, port-based access control, and IGMP snooping for multicast filtering. The 48-pin LQFP package allows simple 4-layer PCB assembly using standard lead-free reflow. Typical applications include industrial Ethernet sensor networks, IP surveillance cameras with daisy-chained switch ports, building automation backbones, factory automation PLCs, and embedded IoT gateways requiring multiple Ethernet ports. The integrated PHYs and small package reduce BOM cost and PCB area versus discrete MAC+PHY solutions. When designing with this device, designers should follow the KSZ8863RLL Hardware Design Checklist from Microchip for crystal and magnetics selection. The 25 MHz reference clock drives the internal PHYs; PHY-to-MAC connection should use impedance-controlled traces per IEEE 802.3 100BASE-TX. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты
KSZ8863RLLI-TR - 3-Port 10/100 Ethernet Switch w/ PHY | Microchip
KSZ8863RLLI-TR

KSZ8863RLLI-TR - 3-Port 10/100 Ethernet Switch w/ PHY | Microchip

The Microchip Technology KSZ8863RLLI-TR is an integrated 3-port 10/100 Mbps managed Ethernet switch with three on-chip PHYs, I2C and SPI host interfaces, and a 48-pin LQFP (7x7 mm) package. It is designed for cost-sensitive, low port-count, power-efficient switching systems, supports IEEE 802.3/802.3u, and provides advanced power management including Energy Efficient Ethernet (EEE) Actiphy and Wake-on-LAN. An Ethernet switch IC is a Layer-2 networking semiconductor that interconnects multiple Ethernet ports within a system, performing MAC address learning, frame forwarding, and QoS prioritization. The KSZ8863 belongs to the unmanaged/lightly-managed switch IC family within the broader Ethernet controller category, sitting alongside standalone PHY transceivers and full Layer-2+ managed switches in the network IC taxonomy. Compared to a discrete PHY plus MAC, an integrated switch-on-chip reduces board area, BOM, and power while adding hardware-based QoS. Key features include three integrated 10/100Base-TX PHYs with HP Auto-MDI/MDI-X, IEEE 802.1Q VLAN tagging support, QoS/priority queues with 802.1p, port-based rate limiting, and per-port cable diagnostics. The RLLI suffix indicates the LQFP-48 industrial-temperature variant (-40C to +85C) supplied in tape-and-reel packaging. The device operates from a single 3.3 V supply with typical power consumption around 0.5 W, and includes a 25 MHz reference clock input. Internally the KSZ8863 uses a store-and-forward architecture with a 1.5 Mbit shared packet buffer, supports RMII for an external MAC or uplink port, and offers PHY loopback for diagnostics. The integrated PHYs include on-chip termination resistors and adaptive equalization, simplifying magnetics selection. Typical applications include industrial Ethernet daisy-chaining, IP cameras and surveillance switches, building automation gateways, factory-floor sensor aggregation, automotive Ethernet gateway modules, and any embedded system that needs a small, low-power 3-port switch. When designing with the KSZ8863RLLI-TR, follow the KSZ8863RLL Hardware Design Checklist for magnetics, RBIAS resistor, and 25 MHz crystal layout. Use short, impedance-controlled 100-ohm differential traces between the PHY outputs and the magnetics, and provide adequate bulk decoupling on each AVDD supply pin. This page synthesizes distributor pricing, pin-compatible alternatives, and practical design notes that are not found in the manufacturer datasheet alone, helping embedded network designers select and source the right switch IC for their application.

Запрос цены Контакты