Товары (39.000+)

M1AFS600-2FGG484 - Fusion FPGA 600K Gates ARM Cortex-M1 | Microchip
M1AFS600-2FGG484

M1AFS600-2FGG484 - Fusion FPGA 600K Gates ARM Cortex-M1 | Microchip

The Microchip Technology M1AFS600-2FGG484 is a flash-based Fusion mixed-signal FPGA delivering 600K system gates, 13,824 logic cells, and 172 user I/Os in a 484-ball Fine-Pitch Ball Grid Array (FBGA) package. The M1 prefix denotes a Fusion FPGA with an embedded ARM Cortex-M1 hard processor core, enabling single-chip embedded system designs at 1.5V core operation. A mixed-signal FPGA is a programmable logic device that integrates digital fabric with analog blocks, flash memory, and clock management circuitry on one die. Unlike SRAM-based FPGAs, flash-based FPGAs such as the Fusion family are non-volatile: configuration data is stored on-chip, so the device is instantly available at power-up and needs no external configuration flash, improving board simplicity and configuration security. Key features include the ARM Cortex-M1 embedded processor for soft-embedded control workloads, large flash memory blocks for on-chip code and data storage, configurable analog circuitry for mixed-signal monitoring, and comprehensive clock generation and management circuitry. The -2 speed grade and 130nm flash process deliver deterministic, low-power logic implementation suited to system-control and data-acquisition roles. Technically, the Fusion architecture combines look-up-table based fabric with ProASIC3-style flash switching, giving single-chip, high-security programmable logic. Monolithic integration of analog monitoring, flash memory, and clock conditioning reduces external component count and total system cost compared to discrete FPGA-plus-analog-plus-flash stacks. Typical applications include industrial automation and motor-system control, embedded processor subsystems where a Cortex-M1 hard core replaces an external MCU, and mixed-signal sensor aggregation boards. The 484-FBGA footprint with 172 I/Os supports moderate-gate-count interface bridging. Designers should note that 0.5mm-pitch BGA escape routing demands appropriate HDI or standard 6+ layer PCB stackups, and the 1.5V core rail should be regulated separately from I/O banks. This page synthesizes distributor listings, drop-in same-footprint variants, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
M1AFS600-FG256 - Fusion Mixed-Signal FPGA | Microchip
M1AFS600-FG256

M1AFS600-FG256 - Fusion Mixed-Signal FPGA | Microchip

The Microchip Technology M1AFS600-FG256 is a Fusion mixed-signal FPGA integrating an ARM Cortex-M1 processor, 600K system gates, and 119 user I/O pins, housed in a 256-ball FBGA (256-LBGA) package. It operates from a 1.5V core supply and is manufactured on a 130nm flash process, combining programmable logic, configurable analog, and large flash memory in a monolithic device. A mixed-signal FPGA is a field-programmable gate array that integrates programmable analog circuitry—such as ADCs, DACs, comparators, and voltage references—alongside digital programmable logic. This allows designers to implement analog front-end functions and digital processing in a single device, reducing BOM count and system complexity. The Fusion family pioneered this category for Microchip (formerly Microsemi/Actel), targeting industrial, medical, and automotive applications that require both analog monitoring and digital control. Key features include an embedded ARM Cortex-M1 soft processor for system management, 600K system gates for custom logic, 110,592 bits of SRAM for data buffering, and up to 119 user I/O pins. It also integrates a 12-bit ADC with configurable analog inputs, analog comparators, and a large flash memory block that acts as non-volatile storage or system configuration memory. The device supports 1.5V core operation with 130nm flash technology, offering low power and secure, non-volatile configuration that starts instantly. The Fusion architecture combines a flash-based FPGA fabric with a hard ARM Cortex-M1 processor subsystem, allowing designers to implement both software and hardware in a single device. The 130nm process provides a balance between density, power, and cost, with maximum internal clock frequencies up to 1098.9 MHz as listed in the device specifications. The configurable analog block includes up to three ADC channels, allowing direct monitoring of external signals without an external ADC chip. The flash configuration memory enables secure, instant-on operation and supports field upgrades via the SPI/I²C interface. Typical application areas include industrial motor control, where the M1AFS600-FG256 can simultaneously handle analog current/voltage sensing, PWM generation, and supervisory logic. It is also used in smart grid and power management systems to monitor grid parameters and control power switches. In medical monitoring devices, its integrated analog front-end and programmable logic permit compact designs with lower power consumption and higher reliability. The device's non-volatile nature makes it ideal for safety-critical systems that require deterministic startup. When designing with this device, pay careful attention to the 1.5V core supply decoupling and the separate I/O bank supplies, which may require 1.5V, 1.8V, 2.5V, or 3.3V depending on interface standards. Use multiple low-ESR ceramic capacitors near each supply pin and a solid ground plane to minimize noise. The configurable analog inputs benefit from a clean analog ground and optional anti-alias filtering. For initial programming, the device can be programmed via JTAG or SPI, and the hardware must support programming voltage levels per the datasheet. This page synthesizes distributor availability, drop-in package alternatives, and practical design notes that go beyond the raw datasheet. It is maintained with verified web-sourced data as of August 31, 2026, and is intended to help engineers evaluate the M1AFS600-FG256 for new designs and to plan for replacement or alternate sourcing.

Запрос цены Контакты
M1AFS600-FG484 - Fusion FPGA 600K Gates, 172 I/O | Microchip
M1AFS600-FG484

M1AFS600-FG484 - Fusion FPGA 600K Gates, 172 I/O | Microchip

The Microchip Technology (Microsemi) M1AFS600-FG484 is a Fusion family mixed-signal FPGA with 600K system gates, 172 user I/O, and an embedded ARM Cortex-M1 soft processor core, housed in a 484-ball FBGA (FG484) package operating from a 1.5V core supply. A mixed-signal FPGA combines reconfigurable programmable logic with analog peripherals on one die. The Fusion family pioneered this integration, sitting in the system hierarchy between pure digital FPGAs and microcontroller-based SoCs: programmable logic fabric plus analog blocks (voltage/temperature monitoring) plus an ARM Cortex-M1 processor, all managed by the flash-based, non-volatile configuration architecture from Actel, now Microchip Technology. Key features include 600K system gates with approximately 110592 bits of configuration memory per DigiKey listing, 172 available user I/O, a 1.5V core operating from the 130nm CMOS flash process, and factory-set speed grades indicated by the FG (standard) ordering code. The embedded ARM Cortex-M1 allows single-chip control-plane and logic-plane designs, reducing external component count and board cost in embedded systems. Technically, the Fusion fabric uses ProASIC3-style flash-based logic cells that retain configuration without external boot memory, improving boot time and security versus SRAM FPGAs. The 130nm CMOS process balances density and cost, and the FBGA 484-ball package provides fine-pitch surface-mount routability for high-I/O designs. Clock resources support system speeds appropriate for glue logic, control, and data-acquisition functions rather than extreme DSP throughputs. Typical applications include industrial control and automation, power-management supervisory systems, building automation controllers, and instrumentation where mixed-signal monitoring plus deterministic logic in one non-volatile device delivers cost and reliability advantages. When designing with this part, plan power-up sequencing and analog reference filtering early, and verify the speed-grade ordering code (FG vs FGG, standard vs -1/-2) matches your timing-closure budget. This page synthesizes verified distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
M1AFS600-FG484I - 600K Gates Fusion FPGA, ARM Cortex-M1 | Microchip
M1AFS600-FG484I

M1AFS600-FG484I - 600K Gates Fusion FPGA, ARM Cortex-M1 | Microchip

The Microchip Technology (Microsemi) M1AFS600-FG484I is a Fusion mixed-signal FPGA with 600,000 equivalent system gates, 13,824 logic cells, 172 user I/Os, and an embedded ARM Cortex-M1 hard processor core, housed in a 484-ball FBGA package rated for the industrial temperature range of -40C to +85C. A field-programmable gate array (FPGA) is a semiconductor device containing a fabric of configurable logic blocks, routing resources, and programmable I/O that designers configure after manufacturing. The Fusion family extends this concept into mixed-signal system-on-chip territory by monolithically integrating configurable analog blocks, large flash memory, clock management circuitry (CCM), and flash-based programmable logic, positioning the M1AFS600 at the top of the hierarchy: FPGA -> mixed-signal FPGA -> programmable SoC -> power management and sensing subsystem. Key features include flash-based configuration that is live at power-up (no external configuration PROM required), 128-bit flash lock and industry-leading AES decryption for IP security, and an embedded ARM Cortex-M1 soft-processing option that allows single-chip control-plane plus logic integration. The 1.5V core supply and 130nm flash process technology keep static and dynamic power manageable for industrial systems. The Fusion fabric pairs digital look-up tables with analog conditioning blocks (voltage, current, temperature monitoring), enabling true single-chip system monitoring and control. The FG484 package provides a 1.0 mm ball pitch for routable, reworkable layouts, and the industrial-grade 'I' suffix guarantees operation from -40C to +85C. Typical applications include industrial system monitoring and power management, embedded control with the ARM Cortex-M1 core, medical instrumentation analog supervision, and automotive-adjacent test equipment requiring flash retention and instant-on configuration. Design consideration: standard FG (lead-containing, non-RoHS) ball metallurgy must be checked against your product environmental requirements; the FGG (lead-free) variant exists in the same footprint for RoHS-driven designs. This page synthesizes distributor inventory, drop-in same-footprint variants, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
M1AFS600-FG484K - 600K-Gate Fusion FPGA, 172 I/O | Microchip
M1AFS600-FG484K

M1AFS600-FG484K - 600K-Gate Fusion FPGA, 172 I/O | Microchip

The Microchip Technology (Microsemi) M1AFS600-FG484K is a Flash-based Fusion field programmable gate array (FPGA) providing 600,000 system gates, 172 user I/Os, and 110592 bits of flash configuration capacity in a 484-ball FBGA (484-BGA) surface-mount package. The device integrates an ARM Cortex-M1 hard processor core, making it a mixed-signal system-on-chip FPGA for single-chip embedded designs. An FPGA (field programmable gate array) is a type of programmable logic device whose interconnect and logic function are configured after manufacturing, sitting within the broader hierarchy of programmable ICs: FPGA -> programmable logic device -> digital IC -> semiconductor. The Fusion family distinguishes itself by combining flash-based programmable fabric (no external configuration PROM required) with analog mixed-signal peripherals, an ARM Cortex-M1 microcontroller subsystem, and industry-standard interfaces. Key features of the M1AFS600-FG484K include 600K system gates of flash fabric, 172 user I/O pins, and instant-on power-up behavior inherent to flash FPGA technology. Because configuration data is stored on-chip in non-volatile flash, the device requires no external boot flash, reduces BOM cost, and improves board-level security against bitstream interception compared with SRAM FPGAs. Architecturally, the Fusion fabric consists of VersaTiles - fine-grained flash switch-based logic tiles - supporting both combinational and sequential implementations, plus embedded flash blocks, SRAM, and analog blocks such as ADC, voltage/temperature monitors, and RTC in the broader family. The ARM Cortex-M1 core allows soft-logic and processor workloads to be partitioned in one device. Typical applications include industrial automation control, portable instrumentation, medical equipment, battery-powered systems, and secure embedded controllers where instant-on, low-power flash FPGA operation and mixed-signal integration matter. When designing with this device, verify the commercial temperature grade (K suffix) suits your environment; industrial-grade I-suffix siblings exist in the same footprint. Check I/O bank voltage assignments in Libero SoC before routing. This page synthesizes distributor availability, same-package drop-in speed/temp-grade alternatives, and engineering design notes not found in the manufacturer datasheet.

Запрос цены Контакты
M1AFS600-FGG484I - 600K Gate Fusion FPGA, 172 I/O | Microchip
M1AFS600-FGG484I

M1AFS600-FGG484I - 600K Gate Fusion FPGA, 172 I/O | Microchip

The Microchip Technology M1AFS600-FGG484I is a Flash-based Fusion mixed-signal FPGA from the Microsemi Fusion family, offering 600K system gates, 172 user I/Os, and integrated ARM Cortex-M1 soft processor support in a 484-ball FBGA (FGG484) package rated for industrial temperature ranges. The M1 prefix denotes Fusion devices that embed ARM Cortex-M1 capability, combining programmable logic, configurable analog blocks, large flash memory arrays, and comprehensive clock management on a single monolithic die fabricated in 130nm process technology at a 1.5V core voltage. A field-programmable gate array (FPGA) is a semiconductor device containing a fabric of configurable logic blocks, routing resources, and I/O cells that the designer programs after manufacturing. Within the programmable logic hierarchy, the Fusion family occupies the mixed-signal SoC tier, sitting above pure digital FPGAs because it adds analog peripherals and system flash, effectively acting as a single-chip power management and control platform. Key features include FlashLock 128-bit flash-based security with industry-leading AES decryption for protecting IP and configuration data, instant-on operation (the device is functional as soon as system power is applied within normal operating specifications), and an analog compute engine for intelligent power and system management. The fabric contains 110592 flash-based logic elements per distributor listings. Because configuration is stored in on-chip flash rather than external boot devices, the M1AFS600 eliminates external configuration PROM cost and board area, improves reliability in harsh environments, and resists configuration-stream interception through its AES-encrypted programming flow. Typical applications include intelligent power management and board-level system control, industrial automation and motor control, portable instrumentation, and secure embedded processing platforms leveraging the ARM Cortex-M1 core. When designing with the M1AFS600-FGG484I, verify power-up sequencing and 1.5V core rail integrity, and allocate adequate thermal relief on the FBGA-484 footprint since thermal performance depends heavily on PCB copper area. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
M1AFS600-FGG484K - Fusion FPGA 600K Gates ARM Cortex-M1 | Microchip
M1AFS600-FGG484K

M1AFS600-FGG484K - Fusion FPGA 600K Gates ARM Cortex-M1 | Microchip

The Microchip Technology (Microsemi) M1AFS600-FGG484K is a Fusion Field Programmable Gate Array (FPGA) IC delivering 600K system gates with 172 user I/Os and 110592 bits of embedded flash memory, housed in a 484-ball Fine-Pitch Ball Grid Array (FBGA) package and rated for operation from -55C to +100C. An FPGA (Field Programmable Gate Array) is a semiconductor device containing programmable logic blocks and interconnects that can be configured by the designer after manufacturing. Within the programmable logic hierarchy, the FPGA sits above CPLDs and below full ASICs, offering high gate counts, embedded memory, and hardware reconfigurability for prototyping and mid-volume production. The Fusion family extends this concept by integrating a hard ARM Cortex-M1 processor core and configurable analog blocks into a single system-on-chip. Key features of the M1AFS600-FGG484K include 600K system gates of programmable fabric, an embedded ARM Cortex-M1 soft/hard processor subsystem for embedded control, 110592 bits of on-chip flash configuration memory, and 172 flexible I/O pins supporting multiple single-ended and differential standards. The 484-BGA package provides high interconnect density for complex designs. Architecturally, the Fusion family combines flash-based configuration with a deterministic fabric, enabling instant-on operation and high security against bitstream cloning. The integrated analog peripherals and processor subsystem reduce external BOM count compared to discrete FPGA-plus-microcontroller solutions. Typical applications include industrial automation controllers, aerospace and defense systems (supported by the -55C to +100C industrial/military temperature range), medical instrumentation, and communications equipment requiring reconfigurable logic with an embedded processor. A key design consideration is power delivery: flash-based FPGAs require stable core and I/O rails with proper decoupling, and the 484-ball BGA demands careful PCB layout with controlled-impedance escape routing. This page synthesizes distributor pricing, drop-in alternatives from the same Fusion family, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
M21012 - 3.2 Gbps Quad Multi-Rate CDR | MACOM
M21012

M21012 - 3.2 Gbps Quad Multi-Rate CDR | MACOM

The MACOM Technology Solutions M21012 is a quad multi-rate clock and data recovery (CDR) integrated circuit with four independent channels for telecom and datacom systems. Each channel operates from 42 Mbps to 3.2 Gbps, and the device is identified in distributor data as a 72-QFN 10 mm by 10 mm fiber-channel, Gigabit Ethernet, and SONET clock-and-data-recovery IC. The verified product data also identifies an 800 MHz reference and one output for the related M21012G-12 ordering variant. A clock and data recovery IC is a semiconductor that extracts timing information from a noisy serial data stream and reconstructs a usable data signal. In the broader hierarchy, a CDR belongs to interface ICs and clock-and-timing recovery functions within high-speed data communications. The M21012 is intended for systems that need parallel adaptation of multiple serial links, particularly multi-lane telecom, optical networking, and datacom equipment. The principal verified feature is its four-channel multi-rate architecture. The 42 Mbps to 3.2 Gbps operating range allows one device family to address several link rates, while independent per-channel recovery supports multi-lane designs. The verified distributor listing also associates the related M21012G-12 variant with fiber-channel, Gigabit Ethernet, and SONET applications, an 800 MHz operating figure, and one output. Exact pin-level electrical limits, supply voltages, jitter specifications, and temperature ratings are not present in the supplied excerpts and must be confirmed from the manufacturer documentation before design release. For optical and backplane-oriented links, CDR functionality helps align serial data with its associated clock before downstream digital logic processes it. The recovered data can reduce the impact of timing distortion introduced by transmission media, connectors, packaging, and crosstalk. The quad organization can also reduce the number of separate recovery devices required in a multi-lane module, although board-level validation remains essential because channel-to-channel skew, power integrity, and loss characteristics depend on the complete implementation. Typical uses include SONET-oriented telecom interfaces, Gigabit Ethernet links, fiber-channel modules, multi-lane datacom equipment, and other serial links operating inside the stated 42 Mbps to 3.2 Gbps range. The exact supported coding, reference-clock requirements, recovery modes, and interface protocol details should be verified in the M21012 datasheet. Do not substitute the related M21012G-12 listing for the exact M21012 without confirming ordering-code compatibility. A practical design review should begin with the manufacturer pinout and package information, followed by high-speed transmission-line routing, controlled impedance, reference-clock integrity, decoupling, and thermal analysis. A CDR cannot compensate for an inadequately designed channel, and its benefit depends on the incoming signal remaining within the device's specified operating conditions. This page consolidates the verified manufacturer description, distributor application details, availability references, and engineering cautions for the M21012. It distinguishes verified facts from parameters requiring datasheet confirmation and does not present unverified substitute parts, electrical limits, pricing, or lifecycle claims as established data.

Запрос цены Контакты
M24256-BWMN6TP - 256Kbit I2C EEPROM, 1MHz, 8-SOIC | STMicroelectronics
M24256-BWMN6TP

M24256-BWMN6TP - 256Kbit I2C EEPROM, 1MHz, 8-SOIC | STMicroelectronics

The STMicroelectronics M24256-BWMN6TP is a 256-Kbit (32 Kbyte) I²C-compatible serial EEPROM organized as 32 K × 8 bits, housed in an 8-pin SOIC (SO-8) package. It operates on a single supply from 2.5 V to 5.5 V, supports a 1 MHz I²C bus clock with a 450 ns access time, and includes three Chip Enable (E0, E1, E2) pins that allow up to eight devices to share the same I²C bus. An EEPROM (Electrically Erasable Programmable Read-Only Memory) is a type of non-volatile memory that retains stored data when power is removed and supports byte-level in-system writes via an electrical signal. EEPROMs sit beneath Flash in the memory hierarchy: they offer lower density but higher endurance per cell (typically 1 million write cycles for this family) and byte-level granularity, making them well suited for storing user-configurable parameters, calibration constants, device IDs, and event logs that change frequently during the lifetime of a product. The M24256-BWMN6TP integrates advanced write-protection features: a Write Protect (WP) pin that hard-locks the upper quadrant of the array, and three hardware address pins that allow bus-address configuration on the fly. The device supports both byte-write and page-write (up to 64-byte page) modes, with a built-in write-cycle completion polling mechanism that simplifies firmware. The SO-8 package is a JEDEC-standard surface-mount form factor widely accepted for industrial designs. Architecturally, the device is built on STMicroelectronics' proprietary CMOS EEPROM process, which delivers >4 million write cycles per byte and >200-year data retention. The on-chip charge pump generates the high-voltage programming pulses required to tunnel electrons through the floating gate, all managed by an internal state machine that frees the host microcontroller from page-buffer timing. Typical applications include industrial control parameter storage, consumer-set user preferences, smart-meter calibration data, automotive accessory identification, medical device log retention, and I²C port expansion on small microcontrollers that lack internal non-volatile storage. Designers choose this part when they need reliable, byte-writeable memory in a familiar 8-pin footprint. When designing with the M24256-BWMN6TP, place 0.1 µF decoupling close to VCC and respect the bus idle time (tBUF) of 0.5 µs minimum to ensure proper start-condition detection. Hardware address pins E0/E1/E2 must be tied to VCC or GND (no floating inputs allowed). This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes for the M24256-BWMN6TP not found in the manufacturer datasheet alone.

Запрос цены Контакты
M24C01-RMN6TP - 1Kbit I2C EEPROM, SOIC-8 | STMicroelectronics
M24C01-RMN6TP

M24C01-RMN6TP - 1Kbit I2C EEPROM, SOIC-8 | STMicroelectronics

The M24C01-RMN6TP is a 1-Kbit (128 x 8-bit) serial I2C EEPROM from STMicroelectronics, housed in an 8-pin SOIC (MN) package. It operates with a supply voltage range of 2.5V to 5.5V, supports I2C bus speeds up to 400 kHz, and features a write cycle time of 5 ms. The device is organized as 128 bytes of non-volatile memory, with a byte-write and page-write capability (up to 16 bytes per page). It includes a write protect (WC) pin for hardware data protection and a device address (E0, E1, E2) input for up to 8 devices on the same bus. An EEPROM (Electrically Erasable Programmable Read-Only Memory) is a type of non-volatile memory that can be electrically erased and reprogrammed. It is a key component in the memory hierarchy, sitting between volatile RAM and permanent storage like flash. EEPROMs are used to store small amounts of configuration data, calibration constants, and device parameters that must persist across power cycles. In the broader system, EEPROMs are part of the memory IC category, which includes ROM, RAM, and flash, and are essential for applications requiring data retention without power. Key features of the M24C01-RMN6TP include a wide operating voltage range (2.5V to 5.5V), I2C interface with clock frequencies up to 400 kHz, and a low-power design with a standby current of 1 uA (typical). The device offers a write cycle time of 5 ms, ensuring fast programming, and supports both byte and page write modes. The SOIC-8 package is industry-standard, making it easy to integrate into existing PCB designs. The device is RoHS compliant and operates over a temperature range of -40C to +85C. Technically, the M24C01 uses a floating-gate transistor architecture for non-volatile storage, with a built-in charge pump for programming. The I2C interface allows for simple two-wire communication (SCL and SDA), with the device address set via three pins (E0, E1, E2), enabling up to 8 devices on a single bus. The write protect pin (WC) provides hardware protection against accidental writes, and the device supports both sequential and random read operations. Typical applications include storing calibration data in industrial sensors, configuration parameters in consumer electronics, and system settings in automotive modules. The wide voltage range and low power consumption make it suitable for battery-powered devices, while the I2C interface simplifies integration with microcontrollers. When designing with this device, ensure proper pull-up resistors on the SCL and SDA lines (typically 4.7 kOhm) and consider the write cycle time when updating data. The WC pin should be tied to ground for normal operation or to VCC for write protection. For high-reliability applications, consider the automotive-grade variant M24C01-RMN6TP/A.

Запрос цены Контакты
M24C02-RMN6TP - 2Kbit I2C EEPROM | STMicroelectronics
M24C02-RMN6TP

M24C02-RMN6TP - 2Kbit I2C EEPROM | STMicroelectronics

The M24C02-RMN6TP is a 2-Kbit (256 x 8-bit) serial I2C EEPROM from STMicroelectronics, housed in a compact SOIC-8 package. It operates over a supply voltage range of 1.8V to 5.5V, supports a clock frequency up to 400 kHz, and features a write cycle time of 5 ms. Data verified as of 2026-08-05. An EEPROM (Electrically Erasable Programmable Read-Only Memory) is a non-volatile memory type that retains data when power is removed, allowing byte-level erasure and reprogramming electrically. In the memory hierarchy, EEPROM sits between volatile RAM and read-only ROM, providing flexible storage for configuration parameters, calibration data, and small application logs. It is a fundamental building block in embedded systems, often interfaced via standard serial protocols like I2C or SPI. Key features include a wide operating voltage range (1.8V to 5.5V) that supports both 3.3V and 5V logic systems, a 400 kHz I2C interface for fast data transfer, and a 5 ms write cycle time for efficient programming. The device also offers a write protect pin to prevent accidental data corruption, and a page write capability of 16 bytes, enhancing programming efficiency. Its low-power consumption makes it suitable for battery-operated devices. The M24C02-RMN6TP uses a standard I2C protocol with a 7-bit device address, allowing up to eight devices on the same bus. It features a self-timed write cycle with auto-erase, simplifying the programming sequence. The device is manufactured using ST's advanced CMOS technology, ensuring high reliability and endurance of 1 million write cycles, with data retention of 40 years. Typical applications include storing calibration data in industrial sensors, configuration parameters in smart meters, and device settings in consumer electronics such as TVs and set-top boxes. Its small SOIC-8 footprint and wide voltage range make it ideal for space-constrained designs. When designing with this device, ensure proper pull-up resistors on the SDA and SCL lines (typically 4.7kΩ for 400 kHz operation) and connect the write protect pin to ground when writing is required. The device supports both byte and page write modes, with page size of 16 bytes, and acknowledges each byte during programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the ST datasheet, providing a comprehensive resource for engineers evaluating the M24C02-RMN6TP.

USD $0,08 Контакты
M24C08-RMN6TP - 8Kbit I2C EEPROM, SOIC-8 | STMicroelectronics
M24C08-RMN6TP

M24C08-RMN6TP - 8Kbit I2C EEPROM, SOIC-8 | STMicroelectronics

The M24C08-RMN6TP is an 8-Kbit (1024 x 8) I2C-compatible serial EEPROM from STMicroelectronics, packaged in an 8-pin SOIC (N) package. It operates over a supply voltage range of 1.8V to 5.5V, making it suitable for a wide range of low-power and battery-operated applications. The device supports a clock frequency of up to 400 kHz (I2C fast mode) and features a write protect pin for hardware data protection. An EEPROM (Electrically Erasable Programmable Read-Only Memory) is a non-volatile memory that can be electrically erased and reprogrammed, retaining data without power. It is a type of memory IC that falls under the broader category of non-volatile memory, which also includes flash memory and MRAM. EEPROMs are used for storing configuration parameters, calibration data, device IDs, and small amounts of firmware that require in-system updates. The M24C08 is part of the M24Cxx family of serial EEPROMs, which are widely used in industrial, automotive, and consumer electronics. Key features of the M24C08-RMN6TP include a byte-write time of 5 ms, a write cycle endurance of 1 million write cycles, and a data retention of 40 years. The device supports both byte and page write modes (up to 16 bytes per page), and sequential read operations. It also includes a write protect (WC) pin that, when tied high, prevents write operations to the entire memory array. The device is available in a standard SOIC-8 package, which is pin-compatible with many other 8-pin EEPROMs, allowing easy drop-in replacement. The M24C08 uses a standard I2C interface with a 2-wire serial bus (SCL and SDA), and supports 7-bit device addressing with three address pins (A0, A1, A2) allowing up to eight devices on the same bus. The device is designed for low-power operation, with a standby current of 1 uA and a maximum active current of 2 mA at 400 kHz. It operates over a temperature range of -40C to +85C, making it suitable for industrial environments. Typical applications include storing calibration data in sensors, configuration settings in set-top boxes, device parameters in smart meters, and system logs in industrial controllers. The M24C08 is also used in automotive electronics for storing VIN numbers, tire pressure monitoring system (TPMS) data, and infotainment system settings. When designing with the M24C08, ensure that the SDA and SCL lines have appropriate pull-up resistors (typically 4.7 kOhm) and that the write protect pin is connected to a defined logic level. The device supports I2C fast mode (400 kHz) and is compatible with standard mode (100 kHz). For reliable operation, decouple the VCC pin with a 0.1 uF ceramic capacitor close to the device.

Запрос цены Контакты
M24C128-RMN6TP - 128Kbit I2C EEPROM, SO-8 | STMicroelectronics
M24C128-RMN6TP

M24C128-RMN6TP - 128Kbit I2C EEPROM, SO-8 | STMicroelectronics

The M24C128-RMN6TP is a 128-Kbit (16K x 8) I2C-compatible EEPROM from STMicroelectronics, packaged in an 8-pin SO-8 (N) package. It operates over a supply voltage range of 1.8V to 5.5V, making it suitable for a wide variety of low-power and battery-operated applications. The device supports I2C clock frequencies up to 1 MHz (Fast-mode Plus) and features a write cycle time of 5 ms, with byte and page write modes (up to 64 bytes per page). An EEPROM (Electrically Erasable Programmable Read-Only Memory) is a non-volatile memory that retains data when power is removed, and can be electrically erased and reprogrammed. It is a type of non-volatile memory (NVM) that sits within the broader memory hierarchy, often used for storing configuration parameters, calibration data, device settings, and small amounts of firmware. EEPROMs are distinct from flash memory in that they allow byte-level erasure and programming, whereas flash typically operates on larger blocks. In a system, EEPROMs serve as a bridge between volatile RAM and permanent storage, providing a flexible and durable solution for data that must survive power cycles. Key features of the M24C128-RMN6TP include a wide operating voltage range (1.8V to 5.5V), low power consumption (standby current of 1 uA typical), and high reliability with 1 million write/erase cycles and 40-year data retention. The device also includes a write protect (WC) pin to prevent accidental writes, and supports both byte and page write operations. The I2C interface allows for easy integration with microcontrollers and other digital systems, with device addressing via three hardware pins (E0, E1, E2) to support up to 8 devices on the same bus. Technically, the M24C128-RMN6TP uses a floating-gate transistor technology for non-volatile storage, with an internal charge pump for programming. The I2C interface is compliant with the I2C bus specification, supporting standard (100 kHz), fast (400 kHz), and fast-mode plus (1 MHz) data rates. The device includes a self-timed write cycle with an internal timer, and an acknowledge polling feature to detect the completion of a write operation. The SO-8 package is a widely used surface-mount package, offering a compact footprint for space-constrained designs. Typical applications include parameter storage in industrial control systems, calibration data in medical devices, configuration settings in consumer electronics, and identification data in smart meters. The wide voltage range and low power consumption make it ideal for battery-powered IoT devices, where it can store sensor calibration and network credentials. In automotive applications, the AEC-Q100 qualified versions (M24C128-RMN6TP is not AEC-Q100 qualified, but the M24C128-RMN6TP-Q1 variant is) are used for odometer and configuration data. When designing with this device, ensure proper decoupling on the VCC pin with a 0.1 uF ceramic capacitor placed close to the device. The SDA and SCL lines should have pull-up resistors (typically 4.7 kOhm for standard mode, 2.2 kOhm for fast mode) to VCC. The write protect pin (WC) should be tied to ground for normal operation, or to VCC to protect the memory from accidental writes. For reliable operation, avoid exceeding the absolute maximum ratings, and consider the write cycle time when planning system operations.

Запрос цены Контакты
M24C16-RMN6TP - 16Kbit I2C EEPROM, SOIC-8 | STMicroelectronics
M24C16-RMN6TP

M24C16-RMN6TP - 16Kbit I2C EEPROM, SOIC-8 | STMicroelectronics

The M24C16-RMN6TP is a 16-Kbit (2 Kbyte) serial I2C EEPROM from STMicroelectronics, organized as 2048 x 8 bits. It operates with a supply voltage range of 1.8V to 5.5V, making it suitable for a wide variety of low-power and battery-operated applications. The device is housed in an 8-pin SOIC (N) package, which is widely used in industrial and consumer electronics. An EEPROM (Electrically Erasable Programmable Read-Only Memory) is a non-volatile memory that retains data when power is removed, and can be electrically erased and reprogrammed. It is a type of non-volatile memory (NVM) that falls under the broader category of memory ICs, which also includes Flash, SRAM, and DRAM. EEPROMs are commonly used for storing configuration parameters, calibration data, device addresses, and small amounts of firmware that require in-system updates. Key features of the M24C16-RMN6TP include a 400 kHz I2C interface, a write cycle time of 5 ms, and a write protect (WC) pin for hardware data protection. It supports byte and page write modes (up to 16 bytes per page), and random and sequential read modes. The device has a typical standby current of 1 uA and an active read current of 0.5 mA, contributing to its low-power profile. It is available in a Pb-free, RoHS-compliant SOIC-8 package, with an operating temperature range of -40C to +85C. The M24C16 uses a standard I2C protocol with a 7-bit device address, where the three least significant bits (E2, E1, E0) are hardware-configurable, allowing up to eight devices on the same bus. The memory array is organized into 128 pages of 16 bytes each. The device includes a noise filter on the SCL and SDA lines to improve bus reliability in noisy environments. Typical applications include smart meters, industrial control systems, medical devices, and consumer electronics where non-volatile storage of small amounts of data is required. The wide voltage range and low power consumption make it ideal for battery-powered IoT sensors and portable devices. When designing with this device, ensure that the I2C bus pull-up resistors are properly sized for the bus capacitance and speed. The write protect pin should be tied to ground if not used, and decoupling capacitors should be placed close to the VCC pin to minimize noise.

Запрос цены Контакты
M24C256-RMN6TP - 256Kbit I2C EEPROM, SOIC-8 | STMicroelectronics
M24C256-RMN6TP

M24C256-RMN6TP - 256Kbit I2C EEPROM, SOIC-8 | STMicroelectronics

The STMicroelectronics M24C256-RMN6TP is a 256-Kbit (32K x 8) I2C-compatible serial EEPROM with a wide operating voltage range of 1.8V to 5.5V, packaged in an 8-pin SOIC (MN) package. It features a 400 kHz clock frequency, a write cycle time of 5 ms, and a 32-byte page write capability, making it suitable for a wide range of data storage applications. An EEPROM (Electrically Erasable Programmable Read-Only Memory) is a non-volatile memory that retains data when power is removed, and can be electrically erased and reprogrammed. It is a type of non-volatile memory (NVM) that sits within the memory hierarchy between volatile RAM and permanent storage like flash. EEPROMs are used for storing configuration parameters, calibration data, device IDs, and small amounts of firmware that require in-system updates. The M24C256 is part of the M24Cxx family of I2C EEPROMs from STMicroelectronics, which are widely used in industrial, automotive, and consumer electronics. Key features include a 256-Kbit memory size, I2C interface with 400 kHz clock, 1.8V to 5.5V supply voltage, 5 ms write cycle time, 32-byte page write, and a write protect pin for hardware data protection. The device also supports sequential read and write operations, and has a 1,000,000 write/erase cycle endurance and 40-year data retention, ensuring reliable long-term data storage. The M24C256 uses a standard I2C two-wire interface (SCL and SDA) with a 7-bit device address, allowing up to 8 devices on the same bus. The device includes a write protect (WC) pin that, when tied high, prevents write operations to the entire memory array. The SOIC-8 package is industry-standard and pin-compatible with many other 256-Kbit I2C EEPROMs, enabling easy drop-in replacement in existing designs. Typical applications include storing configuration parameters in industrial sensors, calibration data in medical devices, device settings in consumer electronics, and firmware parameters in automotive ECUs. The wide voltage range and low power consumption make it suitable for battery-powered IoT devices. When designing with this device, ensure proper pull-up resistors on the SCL and SDA lines (typically 4.7kΩ for 400 kHz operation) and decouple the VCC pin with a 0.1µF ceramic capacitor. The write protect pin should be tied to ground if write protection is not needed, and the address pins (A0, A1, A2) should be tied to VCC or GND to set the device address.

Запрос цены Контакты
M24C32-RMN6TP - 32Kbit I2C EEPROM | STMicroelectronics
M24C32-RMN6TP

M24C32-RMN6TP - 32Kbit I2C EEPROM | STMicroelectronics

The M24C32-RMN6TP is a 32-Kbit (4 Kbyte) serial EEPROM from STMicroelectronics, organized as 4096 words of 8 bits each. It operates over an I2C-compatible two-wire serial interface, supporting clock frequencies up to 400 kHz (Fast mode) and 1 MHz (Fast mode Plus) depending on the voltage range. The device is available in an 8-pin SOIC (MN) package, specifically the SO-8N (150 mil) body, and is supplied in tape and reel packaging (TP suffix). It is designed for low-power and low-voltage applications, with a wide operating voltage range of 1.8V to 5.5V, making it suitable for battery-powered and industrial systems. A serial EEPROM (Electrically Erasable Programmable Read-Only Memory) is a non-volatile memory that retains data when power is removed, and can be electrically erased and reprogrammed in-system. It is a type of EEPROM, which falls under the broader category of non-volatile memory (NVM) in the memory hierarchy. Serial EEPROMs use a serial interface (such as I2C, SPI, or Microwire) to communicate with a host controller, reducing pin count and PCB area compared to parallel EEPROMs. The M24C32 is part of the M24Cxx family of I2C EEPROMs from STMicroelectronics, which includes densities from 1 Kbit to 512 Kbit, all sharing a common command set and addressing scheme. Key features of the M24C32-RMN6TP include a write cycle time of 5 ms (typical), byte and page write modes (up to 32-byte page), and a write protect pin (WC) for hardware data protection. The device supports both sequential and random read modes, and includes an internal write protection scheme with a software write protect feature (via the WC pin). It also features a Schmitt trigger input for noise immunity and a noise filter on the SCL and SDA lines, ensuring reliable operation in electrically noisy environments. The operating temperature range is -40°C to +85°C, and the device is RoHS compliant and halogen-free. Technically, the M24C32 uses a floating-gate transistor technology for non-volatile storage, with a charge pump for programming and erasing. The I2C interface is compatible with standard, fast, and fast mode plus speeds, and the device supports 7-bit and 8-bit device addressing (with three address pins A0, A1, A2 for up to 8 devices on the same bus). The memory array is organized into 128 pages of 32 bytes each, and the device includes a self-timed write cycle with automatic erase-before-write. The write cycle time is 5 ms, and the device has an endurance of 1 million write cycles and a data retention of 40 years. Typical applications include parameter storage in industrial sensors, calibration data in medical devices, configuration storage in networking equipment, and firmware update storage in consumer electronics. The low power consumption (standby current of 1 uA) and wide voltage range make it ideal for battery-operated IoT devices and portable instruments. In an industrial sensor application, the M24C32 can store calibration coefficients and device configuration, which are read at power-up and updated periodically. When designing with this device, ensure that the I2C bus pull-up resistors are properly sized for the bus capacitance and speed. The WC pin should be tied to ground for normal write operations or to VCC for write protection. For reliable operation, decouple the VCC pin with a 0.1 uF ceramic capacitor close to the device. Also, consider the maximum write cycle time (5 ms) when planning write operations, and avoid exceeding the maximum clock frequency for the selected voltage range.

Запрос цены Контакты
M24C512-RMN6TP - 512Kbit I2C EEPROM | STMicroelectronics
M24C512-RMN6TP

M24C512-RMN6TP - 512Kbit I2C EEPROM | STMicroelectronics

The M24C512-RMN6TP is a 512-Kbit (64K x 8) serial I2C EEPROM from STMicroelectronics, packaged in an 8-pin SOIC (SO-8) with a 200 ns write cycle time. It operates from a 1.8V to 5.5V supply voltage and supports clock frequencies up to 1 MHz, making it suitable for a wide range of data storage applications. An EEPROM (Electrically Erasable Programmable Read-Only Memory) is a non-volatile memory that retains data when power is removed, allowing for byte-level read and write operations. It is a type of non-volatile memory (NVM) within the broader memory IC category, which also includes flash memory and SRAM. EEPROMs are commonly used for storing configuration parameters, calibration data, and small amounts of firmware in embedded systems. Key features include a 512-Kbit memory size organized as 64K x 8 bits, a wide operating voltage range of 1.8V to 5.5V, and a maximum clock frequency of 1 MHz. The device supports both 100 kHz and 400 kHz I2C bus speeds, with a write cycle time of 5 ms (typical) and a write protect pin for hardware data protection. It also features a page write capability of up to 128 bytes, enhancing write efficiency. The M24C512-RMN6TP uses a standard I2C interface with a 2-wire serial bus (SCL and SDA), and includes a device address input (E0, E1, E2) allowing up to 8 devices on the same bus. The memory is organized into 512 pages of 128 bytes each, and supports sequential read and write operations. The device is manufactured using ST's advanced CMOS technology, ensuring low power consumption and high reliability. Typical applications include industrial control systems, smart meters, medical devices, and automotive electronics, where reliable non-volatile data storage is required. The wide voltage range and high clock speed make it suitable for both battery-powered and high-speed systems. When designing with this device, ensure proper decoupling capacitors on the power supply and pull-up resistors on the I2C lines. The write protect pin should be tied to ground for normal operation or to VCC to prevent accidental writes. The device is RoHS compliant and halogen-free, meeting environmental standards.

Запрос цены Контакты
M24C64-DRMF3TG/K - 64Kbit I2C EEPROM, 1MHz, AEC-Q100 | STMicroelectronics
M24C64-DRMF3TG/K

M24C64-DRMF3TG/K - 64Kbit I2C EEPROM, 1MHz, AEC-Q100 | STMicroelectronics

The STMicroelectronics M24C64-DRMF3TG/K is an automotive-grade 64-Kbit serial I2C bus EEPROM organized as 8K × 8 bits, housed in an 8-terminal MLP (2x3 mm) Wettable Flank DFN package. It operates from a 2.5V to 5.5V supply, supports a 1 MHz I2C clock with 450 ns access time, and is qualified to AEC-Q100 grade 1 for automotive applications with an operating temperature range of -40°C to +125°C. The device offers byte-level and page-level write operations, hardware write protection via the WC pin, and 4 million erase/write cycles endurance with more than 200-year data retention. An EEPROM (Electrically Erasable Programmable Read-Only Memory) is a type of non-volatile memory that retains stored data when power is removed and supports individual byte-level electrical erasure and reprogramming. In the hierarchy of non-volatile memory (EEPROM -> NVM -> memory IC -> semiconductor), I2C EEPROMs such as the M24C64 family occupy the low-density, byte-addressable niche used for configuration storage, calibration constants, and small user data sets where simplicity, low pin count, and long retention are valued over speed or density. Key features include a 1 MHz I2C / SMBus-compatible two-wire interface, a 32-byte page write buffer for fast bulk writes, hardware write-protect input, built-in ECC for single-bit error correction, and a dedicated supply monitoring block that in-progress write protection when VCC drops below threshold. The device supports both standard (100 kHz), fast (400 kHz), and fast-plus (1 MHz) I2C modes, and the selectable device address bits (A0-A2) allow up to 8 devices on a single bus. The M24C64-DRMF3TG/K uses CMOS technology with a low-power design that draws sub-microamp standby current, making it well suited for always-on subsystems in automotive ECUs, body control modules, and infotainment head units. The MLP-8 (2x3 mm) Wettable Flank package provides both small PCB footprint and automated optical inspection (AOI) capability required by automotive PCB assembly lines. Typical applications include automotive parameter storage in body and chassis modules, infotainment system configuration, smart junction box settings, battery management system (BMS) calibration data, and industrial IoT nodes requiring AEC-Q100 grade non-volatile memory. The wide 2.5V-5.5V supply range lets it interface directly with both 3.3V microcontrollers and legacy 5V systems without level translation. When designing with this device, observe the 5 ms maximum write cycle time per page and add a small polling loop in firmware to verify completion via ACK polling on the write address. The WC pin must be tied to GND for normal write operation or to VCC to permanently lock the memory array against accidental modification. Decouple VCC with a 100 nF ceramic capacitor placed within 5 mm of the supply pin.

Запрос цены Контакты
M24C64-RMN6TP - 64Kbit I2C EEPROM | STMicroelectronics
M24C64-RMN6TP

M24C64-RMN6TP - 64Kbit I2C EEPROM | STMicroelectronics

The M24C64-RMN6TP is a 64-Kbit (8K x 8) serial I2C EEPROM from STMicroelectronics, packaged in a compact SO-8 (N) package. It operates over a supply voltage range of 1.8V to 5.5V, with a maximum clock frequency of 1 MHz (for VCC >= 4.5V) and 400 kHz (for VCC >= 2.5V). The device features a byte-write time of 5 ms and a write cycle endurance of 1 million write cycles, with data retention of 40 years. Data verified as of 2026-08-05. An EEPROM (Electrically Erasable Programmable Read-Only Memory) is a non-volatile memory that can be electrically erased and reprogrammed. It is a type of memory IC that retains data when power is removed, making it essential for storing configuration parameters, calibration data, and small amounts of firmware in embedded systems. EEPROMs sit within the memory hierarchy as a non-volatile storage layer, distinct from volatile RAM and higher-capacity flash memory, and are commonly used for byte-level read/write operations in applications requiring frequent updates. Key features include a wide operating voltage range (1.8V to 5.5V), I2C interface with 7-bit device addressing, and a write protect pin for hardware data protection. The device supports sequential read and write operations, and includes a self-timed programming cycle with an internal write cycle time of 5 ms. The SO-8 package is industry-standard, enabling drop-in compatibility with many other 64-Kbit I2C EEPROMs. The M24C64-RMN6TP uses a floating-gate transistor architecture for non-volatile storage, with a charge pump for internal programming voltage generation. The I2C interface supports standard (100 kHz), fast (400 kHz), and fast-plus (1 MHz) modes, allowing flexible integration with microcontrollers. The device includes a write cycle time of 5 ms, which is typical for EEPROMs, and supports a write protect feature to prevent accidental writes. Typical applications include parameter storage in industrial sensors, calibration data in medical devices, configuration storage in networking equipment, and firmware updates in consumer electronics. The wide voltage range and low power consumption make it suitable for battery-powered IoT devices, while the high endurance (1 million cycles) supports frequent data logging. When designing with this device, ensure the I2C bus pull-up resistors are properly sized for the clock frequency and bus capacitance. The write protect pin should be tied to ground if not used, and the device address pins (A0, A1, A2) must be set to avoid conflicts with other I2C devices on the bus. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, providing a comprehensive resource for engineers selecting a 64-Kbit I2C EEPROM.

USD $0,08 Контакты
M25P16-VMF3PB - 16Mbit SPI NOR Flash 75MHz | Micron
M25P16-VMF3PB

M25P16-VMF3PB - 16Mbit SPI NOR Flash 75MHz | Micron

The Micron Technology M25P16-VMF3PB is a 16 Mbit (2 Mb x 8) serial NOR Flash memory operating on an SPI-compatible bus at clock frequencies up to 75 MHz, supplied at 2.7 V to 3.6 V in a 16-pin SOP2 (16-SO) surface-mount package rated for -40 C to +125 C automotive temperature ranges. Serial NOR Flash is a non-volatile memory category that stores code and data in a NOR array architecture, allowing random access to any address through a simple serial peripheral interface (SPI). In the system memory hierarchy, it sits alongside parallel NOR and NAND Flash as a code-storage device, and is a direct descendant of the Numonyx/ST M25P family later acquired into the Micron portfolio. Compared with parallel Flash, SPI NOR reduces pin count, board area, and controller I/O requirements, which is why it dominates boot-code and firmware-storage roles in embedded designs. Key features of the M25P16-VMF3PB include its 75 MHz maximum clock frequency for fast code shadowing and XIP-style access, 2 Mb x 8 organization with 32 sectors of 64 Kbyte each (4 Kbyte subsector granularity via standard erase commands), advanced write-protection mechanisms, and deep power-down mode for minimum standby consumption. The automotive-grade suffix (PB, extended temperature) supports designs qualified to demanding environmental requirements. Architecturally, the device executes a standard SPI command set: READ and FAST_READ for data retrieval, PAGE PROGRAM for 256-byte page writes, SECTOR ERASE and BULK ERASE for content management, plus status-register and write-protect commands. The dedicated HOLD pin pauses serial communication without releasing the bus, and a hardware reset pin (S_RST on the 16-pin package) allows recovery of the serial interface. Typical applications include boot firmware storage for DSPs and microcontrollers, FPGA configuration bitstreams, parameter and calibration data storage in automotive modules, industrial drives, and set-top-box platforms. When designing with this device, verify hold times at the full 75 MHz clock and decouple VCC with 100 nF close to the supply pin; the 16-SOP2 footprint is wider than the 8-SO variant, so confirm the land pattern before second-sourcing. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
M25P16-VMF3TPB - 16Mb SPI NOR Flash 75MHz | Micron
M25P16-VMF3TPB

M25P16-VMF3TPB - 16Mb SPI NOR Flash 75MHz | Micron

The Micron M25P16-VMF3TPB is a 16Mb (2Mb x 8) serial NOR Flash memory with an SPI-compatible bus interface, up to 75 MHz clock support, and a 2.7V to 3.6V supply range, housed in a 16-pin SOIC wide-body (SO16W, 300 mil) package with -40C to +125C operation. Serial NOR Flash is a nonvolatile memory that stores code and data and is read over a simple four-wire SPI bus (chip select S, serial clock C, serial data input D, and serial data output Q). In the embedded-systems hierarchy it sits below parallel NOR and DRAM in bandwidth but above I2C EEPROMs in speed and density, making it the de facto standard for boot-code storage in microcontrollers, DSPs, and FPGAs. Key features of the M25P16 include 75 MHz SPI read operation, fast page programming (256-byte pages) and sector erase (64 KB sectors) with block protection, 15 ns clock-to-output access timing, and advanced write-protection mechanisms including status-register and hardware write protect. The VMF3 ordering option denotes the wide 16-pin SO package, RoHS-compliant lead-free construction, and Tape & Reel delivery, with the TP suffix indicating the shipping format. Architecturally, the device is an SLC single-level-cell NOR array organized as 2M x 8 bits, with an internal state machine that executes Read, Fast Read, Page Program, Sector Erase, Bulk Erase, and Write Status Register commands. Micron assigned this part to its Product Longevity Program, which suits multi-year industrial deployments; however, Micron has since EOL'd low-density serial NOR families, so the Renesas-published conversion guide to Adesto FUSION/Standard Flash and the cross-brand equivalents below are relevant for new sourcing. Typical applications include FPGA/DSP boot configuration (for example SHARC DSP boot loaders), BIOS/firmware storage in networking equipment, parameter and calibration data logging in industrial drives, and set-top-box or display firmware storage. Design consideration: hold the HOLD pin high and tie WRITE PROTECT appropriately; use 100 nF decoupling at VCC and respect the deep power-down entry/exit timing to minimize standby current. This page synthesizes verified distributor data, drop-in same-package alternatives, and sourcing guidance for a part affected by Micron EOL - information not consolidated in the manufacturer datasheet.

Запрос цены Контакты
M25P16-VMN3PB - 16Mb SPI NOR Flash 75MHz SOIC-8 | Micron
M25P16-VMN3PB

M25P16-VMN3PB - 16Mb SPI NOR Flash 75MHz SOIC-8 | Micron

The Micron M25P16-VMN3PB is a 16 Mbit (2 M x 8) serial NOR Flash memory with a high-speed SPI-compatible bus, clocking up to 75 MHz, in an 8-pin SOIC (208-mil SO, SOP) package. It is rated for the automotive temperature grade of -40C to +125C and is covered by Micron's Product Longevity Program. Serial NOR Flash is a non-volatile memory category within the broader memory IC and semiconductor hierarchy. Unlike NAND Flash, NOR Flash allows random-access reads of individual bytes, making it the standard choice for firmware boot code storage in embedded systems, where the processor must execute or quickly fetch code directly from the memory array over an SPI bus. Key features of the M25P16 include 16,777,216 bits of SLC (single-level cell) NOR storage organized as 2,097,152 bytes x 8, a 75 MHz maximum SPI clock frequency, 100,000 program/erase cycles endurance, and advanced write-protection mechanisms. Page program and sector erase operations are supported with block-level protection for reliable code and data storage. Architecturally, the device uses a standard SPI interface with signals S (chip select), D (serial data input), Q (serial data output), and C (serial clock), plus WP# (hardware write protect) and HOLD# (pause communication without deselecting). The automotive temperature grade and Product Longevity Program membership make it suitable for long-lifecycle deployments where sourcing continuity matters. Typical applications include automotive modules, industrial controllers, embedded firmware boot storage, data logging, computing modules, and configuration storage for FPGAs and SoCs requiring dependable non-volatile code memory. Design tip: verify VCC decoupling and use hold operations carefully - releasing HOLD# mid-clock requires an edge on C to resume, so keep timing margins in multi-master SPI buses. This page adds distributor pricing tiers, drop-in alternative cross-references, and practical design notes not consolidated in the manufacturer datasheet.

Запрос цены Контакты
M25P16-VMN3YPB - 16Mbit SPI NOR Flash 75MHz SOIC-8 | Micron
M25P16-VMN3YPB

M25P16-VMN3YPB - 16Mbit SPI NOR Flash 75MHz SOIC-8 | Micron

The Micron M25P16-VMN3YPB is a 16Mbit (2MB) serial NOR Flash memory with an SPI interface operating up to 75 MHz, supplied in an 8-pin SOIC (8-SO, 3.90 mm width) package with automotive temperature grade. It stores data as 16M x 1 bits and uses a standard SPI command set for read, page program, and sector erase operations. Serial NOR Flash is a nonvolatile memory category within the memory IC hierarchy (Flash memory -> NOR Flash -> serial/SPI NOR Flash -> nonvolatile semiconductor memory). Unlike parallel NOR devices, SPI NOR Flash uses a reduced pin count (8 pins) communicating over a clocked serial bus, which makes it ideal for storing boot code, firmware, and configuration data in space-constrained embedded systems. Key features of the M25P16-VMN3YPB include its 16Mbit density organized for x1 SPI access, a 75 MHz maximum clock frequency for fast code-shadowing reads, and an automotive temperature grade per distributor data (Partstack/Vyrian list Temperature Grade: AUTOMOTIVE), supporting -40C to +125C environments. The 8-SOIC footprint is industry-standard, easing second-source qualification. Architecturally, the device is organized into pages for programming and larger sectors for erase, with the standard Micron M25P family command set (READ, FAST_READ, PAGE PROGRAM, SECTOR ERASE, BULK ERASE, write protection via the /W pin, and /HOLD for bus suspension). This command compatibility is why the M25P16 is frequently cross-referenced by vendors such as STMicroelectronics and Winbond equivalents in the same SOIC-8 footprint. Typical applications include FPGA configuration bitstream storage, microcontroller boot firmware, automotive infotainment and body-control module code storage, LCD display panel parameter memory, and communication equipment configuration storage. The 75 MHz SPI clock supports fast boot-time readout where a quad interface is not required. Design consideration: verify the supply range and pin functions against the manufacturer datasheet before drop-in substitution; the /W (write-protect) and /HOLD pins must be driven correctly by the host, as not all competitor devices define identical hold behavior. This page synthesizes distributor pricing, stock data, drop-in alternatives, and practical design notes not found in a single datasheet, giving engineers a complete qualification-ready view of the M25P16-VMN3YPB.

Запрос цены Контакты
M25P16-VMN6P - 16Mb SPI NOR Flash 75MHz SOIC-8 | Micron
M25P16-VMN6P

M25P16-VMN6P - 16Mb SPI NOR Flash 75MHz SOIC-8 | Micron

The Micron M25P16-VMN6P is a 16-Mbit (2 Mbit x 8) serial NOR Flash memory device with an SPI-compatible bus interface, packaged in an 8-pin SOIC (SO8) with 75 MHz maximum clock frequency. It features advanced write-protection mechanisms including block-lock protect bits and a hardware write-protect pin, and operates from a single 2.7 V to 3.6 V supply. The device delivers typical page-program time of 1.4 ms for up to 256 bytes, sector-erase time of 0.65 s, and bulk-erase time of 4 s, with JEDEC-standard SFDP (Serial Flash Discoverable Parameters) read access. A NOR Flash memory is a non-volatile storage technology that retains data without power and supports random (byte-level) read access, unlike NAND Flash which is read sequentially by page. The NOR architecture makes it ideal for code storage and execute-in-place (XIP) boot ROM applications where deterministic, low-latency reads are required at system power-up. The SPI (Serial Peripheral Interface) bus reduces pin count versus parallel NOR, allowing the device to share a 4-wire (or 3-wire) bus with other peripherals and saving PCB area in compact embedded designs. Key specifications include a 75 MHz SPI clock (50 MHz for legacy read commands), 32-Kbyte and 64-Kbyte sector architecture, JEDEC 2-byte electronic signature, and an industry-standard command set compatible with many prior-generation SPI Flash devices. The 8-pin SOIC package provides 3 mm x 4.9 mm board area, supporting both commercial (0 C to 70 C) and industrial (-40 C to +85 C) operating ranges. The M25P16 architecture uses a single 2.7-3.6 V supply, on-chip write/erase voltage generation, and a deep power-down mode drawing typically 1 uA for battery-backed applications. Hardware sector protection and software block-lock bits allow designers to enforce bootloader read-only zones for secure firmware-update implementations. Typical applications include router firmware storage, IoT sensor node boot memory, set-top box data logging, industrial PLC parameter storage, and consumer electronics such as printers and smart-home gateways where small-footprint code and parameter storage is required. Compared to EEPROM, NOR Flash provides higher density per die at lower cost per Mbit but requires block-level erase before write. When designing with this device, ensure VCC decoupling of 100 nF plus 4.7 uF is placed within 5 mm of the VCC pin to suppress write/erase inrush transients. The /WP and /HOLD pins must be tied to VCC (or pulled high) if unused, and the /CS line must be returned to logic high between commands to reset the SPI state machine.

Запрос цены Контакты