5M40ZE64C4N - MAX V CPLD, 32 LE, 64-EQFP, Low-Power | Intel
Артикул: 5M40ZE64C4N ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $2.85 | $2,85 |
| 10 | $2.55 | $25,50 |
| 100 | $2.2 | $220,00 |
| 500 | $1.92 | $960,00 |
| 1.000 | $1.7 | $1.700,00 |
5M40ZE64C4N Обзор
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that bridges the gap between simple PLDs and larger FPGAs. Within the broader programmable logic taxonomy, a CPLD sits below FPGAs in density but offers deterministic timing, instant-on behavior, and high I/O count for glue-logic applications. CPLDs are commonly used for I/O expansion, bus interface bridging, power sequencing, and state-machine control where FPGAs would be over-engineered.
The 5M40ZE64C4N integrates 32 logic elements, 4 Kbits of embedded user flash memory, and a MultiTrack interconnect architecture with a 7.5 ns tPD1 propagation delay. It supports LVCMOS, LVTTL, and 1.8 V/2.5 V/3.3 V I/O standards through flexible banked I/O architecture. Internal pull-up resistors are provided on user I/O pins, simplifying PCB routing by reducing the need for external components.
Designed for low-power operation, the 5M40ZE64C4N typically consumes only a few milliamps in active mode and supports a standby/Idle mode for battery-powered systems. The flash-based configuration cell eliminates the need for external boot memory and provides instant-on operation immediately after power-up, which is critical in power-sequenced industrial systems. The device is programmed via the JTAG (IEEE 1149.1) interface and is supported by the Quartus II / Quartus Prime design toolchain.
Typical applications include I/O expansion and bus bridging in industrial control systems, power-supply sequencing logic in telecom equipment, glue logic replacement in legacy designs, and state-machine control in consumer electronics. The 64-pin EQFP package also suits through-hole-friendly prototyping environments.
When designing with this device, ensure decoupling is placed close to each supply pin and verify that all I/O bank voltages match the connected logic levels. The internal pull-up resistors can usually be enabled per-pin in the Quartus tool to avoid external resistor placement. JTAG chain ordering must be planned carefully when the CPLD shares the programming bus with other devices.
This page consolidates current distributor pricing, drop-in compatible alternatives, and design considerations beyond what is found in the standalone datasheet, supporting engineers evaluating the 5M40ZE64C4N for new designs or as a replacement in legacy systems.
Аналоги без доработки для 5M40ZE64C4N — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с 5M40ZE64C4N (тот же форм-фактор и посадочное место) — отличается по Package, Configuration Memory, Operating Temperature, Programming Interface, Logic Elements (LE).
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
5M40ZE64C5N
✅ Прямая замена✓ В наличии
$4.85 / шт.
Открыть даташит →5M40ZE64A5N
✅ Прямая замена✓ В наличии
$2.18 / шт.
Открыть даташит →5M160ZE64C4N
✅ Прямая замена✓ В наличии
$4.3 / шт.
Открыть даташит →5M160ZE64C5N
✅ Прямая замена✓ В наличии
$4.95 / шт.
Открыть даташит →5M40ZE64I5N
✅ Прямая замена✓ В наличии
$2.74 / шт.
Открыть даташит →LC4032ZE-7TN64C
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
5M40ZE64C4N Максимальные параметры и электрические характеристики
| Family | MAX V |
| Logic Elements (LE) | 32 |
| User Flash Memory | 4 Kbit |
| Pin-to-Pin Delay (tPD1) | 7.5 ns |
| Maximum Internal Frequency | 184 MHz |
| Number of I/O Pins | 30 (approx.) |
| Supply Voltage (VCCINT) | 1.8 V |
| I/O Bank Voltage | 1.8 V / 2.5 V / 3.3 V |
| Process Technology | 0.18 µm flash-based CMOS |
| Configuration Memory | Non-volatile flash (internal) |
| Programmable Pull-up Resistors | Yes (per-pin, internal) |
| Programming Interface | JTAG (IEEE 1149.1) |
| Рабочая температура | 0 °C to +85 °C (commercial) |
| Корпус | EQFP-64 (Plastic Enhanced QFP, 64 pins) |
| Тип монтажа | Surface Mount |
| Уровень MSL | 3 (per JEDEC J-STD-020) |
| Статус RoHS | Compliant |
Руководство по цоколевке 5M40ZE64C4N в корпусе eqfp-64 (plastic enhanced qfp, 64 pins)
Цоколевка для 5M40ZE64C4N (корпус eqfp-64 (plastic enhanced qfp, 64 pins)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для 5M40ZE64C4N.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
5M40ZE64C4N подходит для 6 применениеs: Industrial I/O Expansion and Bus Bridging, Power Supply Sequencing and Supervisory Logic, Telecom Line Card Glue Logic, Consumer Electronics State-Machine Control, Legacy FPGA I/O Bank Expansion, Automotive Body Electronics (Non-Safety).
Industrial I/O Expansion and Bus Bridging
The 5M40ZE64C4N is well suited for industrial I/O expansion and bus-bridging applications. Its 32 logic elements, 7.5 ns pin-to-pin delay, and 184 MHz maximum internal frequency are sufficient for address decoding, chip-select generation, and protocol translation between legacy parallel buses. According to the MAX V datasheet, the multi-voltage I/O bank architecture supports 1.8 V, 2.5 V, and 3.3 V logic without external level shifters, which simplifies industrial PLC designs. Internal pull-up resistors reduce external component count, while non-volatile flash configuration guarantees deterministic start-up behavior for fail-safe industrial systems. The 64-pin EQFP package is footprint-compatible with other MAX V EQFP-64 variants, enabling upward migration as designs grow.
Рекомендуется
Power Supply Sequencing and Supervisory Logic
The 5M40ZE64C4N is commonly used in power-supply sequencing and supervisory logic for multi-rail systems. Its instant-on non-volatile flash configuration means the device is active at the first valid power rail, well before any FPGA or ASIC completes its boot sequence. The 32 logic elements are adequate for sequencing 4 to 6 power rails, implementing watchdog timers, and asserting reset signals based on monitored voltages. According to the MAX V datasheet, the device's low standby current makes it appropriate for always-on supervisory blocks. Designers can implement state machines that meet safety standards for hot-swap and ATX-style power architectures using the CPLD's deterministic timing guarantees.
Рекомендуется
Telecom Line Card Glue Logic
Telecom line-card designs frequently deploy the 5M40ZE64C4N for glue logic between framer ICs, SERDES devices, and backplane transceivers. Its 7.5 ns propagation delay enables reliable interfacing with TDM and low-speed SERDES lanes, while 32 logic elements suffice for channelized mux/demux, parity generation, and alarm aggregation. According to the MAX V datasheet, JTAG in-system programmability simplifies field upgrades across thousands of deployed line cards. The non-volatile configuration eliminates any risk of misprogramming on power-up, a critical requirement for carrier-grade equipment. Internal pull-up resistors reduce the bill of materials on densely populated telecom PCBs where every saved component improves thermal performance.
Рекомендуется
Consumer Electronics State-Machine Control
Consumer electronics products such as appliances, set-top boxes, and printers use the 5M40ZE64C4N for state-machine control and discrete logic replacement. The 32 logic elements comfortably encode multi-state user-interface flows, button-debouncing logic, and discrete PWM generation. According to the MAX V datasheet, the device's small EQFP-64 footprint, instant-on behavior, and low cost make it ideal for cost-sensitive consumer products. Designers can replace discrete 74-series logic packages with a single CPLD, reducing PCB area and assembly cost. Internal pull-ups eliminate dozens of external resistors, and the JTAG interface supports in-system firmware updates during production testing.
Рекомендуется
Legacy FPGA I/O Bank Expansion
The 5M40ZE64C4N is frequently deployed to expand I/O count in legacy FPGA-based systems where the main FPGA has run out of user I/O but has spare logic capacity that must be preserved. The CPLD handles low-speed GPIO expansion, LCD/LED driving, and key-matrix scanning while the main FPGA focuses on signal processing. Per the MAX V datasheet, the device supports all common LVCMOS and LVTTL standards across its I/O banks, allowing direct connection to FPGA banks of any supported voltage. The non-volatile flash configuration means the I/O expansion logic is available immediately at power-up, ahead of FPGA configuration completion. This makes the CPLD ideal for bootstrapping FPGA configuration and providing early-board health signals.
Рекомендуется
Automotive Body Electronics (Non-Safety)
For non-safety automotive body electronics such as interior lighting controllers, seat-adjustment modules, and body control modules, the 5M40ZE64C4N and its automotive-grade counterpart 5M40ZE64A5N offer a flexible logic platform. The automotive variant supports an extended -40 °C to +125 °C temperature range per the MAX V datasheet, and the same 32 LE density is sufficient for lamp drivers, switch debouncing, and LIN/CAN interface glue logic. The non-volatile flash configuration provides deterministic start-up behavior required by body-control networks. Designers benefit from instant-on operation, multi-voltage I/O compatibility, and field-upgradable JTAG programming, all in a surface-mount EQFP-64 package.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для 5M40ZE64C4N — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | 5M40ZE64C5N | 5M40ZE64A5N | 5M160ZE64C4N | 5M160ZE64C5N | 5M40ZE64I5N | LC4032ZE-7TN64C |
|---|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Lattice Semiconductor |
| Package | EQFP-64 | EQFP-64 - same | EQFP-64 - same | EQFP-64 - same | EQFP-64 - same | EQFP-64 - same | TQFP-64 - pin-compatible (TQFP/EQFP family) |
| Logic Elements / Macrocells | 32 LE | 32 LE | 32 LE | 160 LE | 160 LE | 32 LE | 32 macrocells |
| Configuration Memory | Internal flash (non-volatile) | Internal flash (non-volatile) | Internal flash (non-volatile) | Internal flash (non-volatile) | Internal flash (non-volatile) | Internal flash (non-volatile) | Internal flash (non-volatile, E²CMOS) |
| Programming Interface | JTAG (IEEE 1149.1) | JTAG | JTAG | JTAG | JTAG | JTAG | JTAG (IEEE 1149.1) |
| Temperature Grade | Commercial (0 °C to +85 °C) | Commercial | Automotive (-40 °C to +125 °C) | Commercial | Commercial | Industrial (-40 °C to +100 °C) | Commercial |
Ключевые отличия
- Smallest LE-count MAX V with non-volatile instant-on configuration (против 5M160ZE64C4N)
- Cross-brand pin-compatible Lattice alternative available (против LC4032ZE-7TN64C)
- Lower propagation-delay speed-grade options in same package (против 5M40ZE64A5N)
Заметки по проектированию
The 5M40ZE64C4N requires a single 1.8 V core supply on VCCINT and one or more bank supplies for the I/O (1.8 V, 2.5 V, or 3.3 V). According to the MAX V datasheet, place at least one 0.1 µF decoupling capacitor close to every supply pin and a 10 µF bulk capacitor near the package. Power-up sequencing is not strictly required, but all VCCINT and VCCIO rails should rise monotonically within the datasheet's specified tramp limits to avoid excessive inrush current through the I/O cells.
The EQFP-64 package has 0.8 mm pitch leads with exposed die-pad handling not required. Provide at least one continuous ground plane on the layer directly beneath the device and route JTAG signals (TCK, TMS, TDI, TDO) with short stubs to minimize ringing. Per the MAX V handbook, the JTAG TCK trace should be length-matched if it is shared with other devices in the chain. Keep TCK away from switching signals and noisy power rails to avoid programming failures during in-system programming.
Do not assume the 5M40ZE64C4N is fully pin-compatible with all 64-pin QFP CPLDs from other vendors. While the Lattice LC4032ZE-7TN64C uses the same TQFP-64 footprint and similar JTAG pinout, bank-voltage assignments and dedicated pin functions (GCLK, DEV_OE, DEV_CLRn) differ. Always re-import the target device's pinout into Quartus Prime and verify all dedicated-pin assignments before PCB layout is finalized. Mixing MAX V and ispMACH pin definitions without verification is a frequent source of dead-board prototypes.
When using the 5M40ZE64C4N as a bus-bridging device, enable the internal pull-up resistors only on inputs that truly require a default-high state, since every enabled pull-up adds tens of microamps of bias current per pin. According to the MAX V datasheet, the LVCMOS output drive strength (default 4 mA) can be increased in Quartus Prime to 8 mA or 16 mA for heavily loaded buses. Slew-rate control (slow/fast) is also programmable per pin and should be set to 'slow' for clock-like signals to reduce EMI emissions.
Информация о соответствии
RoHS compliance confirmed via DigiKey product listing (544-3180-ND) and Alldatasheet part record. AEC-Q100 qualification is not_applicable for the commercial-grade 5M40ZE64C4N; the 5M40ZE64A5N variant is the automotive-grade option. REACH, halogen-free, and conflict-minerals declarations were not present in the verified data and are marked 'unknown' rather than fabricated.
