AD602JRZ - Dual 35MHz Variable Gain Amplifier | Analog Devices
Артикул: AD602JRZ ✓ АктивенAD602JRZ Обзор
A variable gain amplifier, or VGA, is a linear amplifier whose gain can be adjusted by an external control signal. In the broader semiconductor hierarchy, a VGA belongs to the amplifier IC and analog signal-processing categories. AD602VGAs are commonly positioned ahead of analog-to-digital converters, where received or reflected signals vary widely in amplitude and must be normalized before digitization. The AD602 combines that adjustable gain with two independent channels, allowing simultaneous processing of two signal paths.
The AD602 provides a −10 dB to +30 dB gain range, 31.07 dB maximum gain, and a nominally gain-independent 35 MHz −3 dB bandwidth. Its gating control input is compatible with TTL and CMOS logic. These characteristics make the amplifier suitable for systems in which the gain-control voltage must interface directly with digital control hardware while the analog signal remains wideband.
Each of the two amplifier channels has its own gain-control input, allowing the channels to be adjusted independently rather than sharing a common gain command. The broad bandwidth can support ultrasound echo reception, medical imaging, instrumentation, and other wideband analog systems. The −10 dB lower gain range also provides attenuation capability that can help control signal level before downstream conversion or filtering stages.
Typical uses include receive channels in ultrasound imaging equipment, dual-axis sensor interfaces, communications and instrumentation front ends, and precision analog measurement systems. In an ultrasound receiver, the amplifier can normalize the amplitude of returning echoes before they reach an ADC. Independent dual-channel adjustment is valuable when the two channels carry different signal amplitudes or require different attenuation settings.
Designers should preserve adequate supply headroom and use the manufacturer-recommended decoupling and gain-control interface practices. The gain-control voltage range, output swing, and input common-mode limits must be checked against the actual signal chain. Because wideband amplifiers amplify noise as well as signal, input shielding, grounding, source impedance, and controlled impedance routing are important to achieving the intended system noise performance.
This page organizes the AD602JRZ electrical characteristics, supply requirements, package information, application guidance, comparison criteria, and design considerations into a practical engineering reference. It also distinguishes exact drop-in alternatives from related AD600 and AD602 variants whose gain ranges, temperature grades, or delivery packaging differ, helping engineers avoid replacements that require board or circuit changes.
Аналоги без доработки для AD602JRZ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с AD602JRZ (тот же форм-фактор и посадочное место) — отличается по Package, Gain Range, Operating Temperature, Product Type, Signal Type.
AD602ARZ
✅ Прямая заменаУточнить цену
Открыть даташит →AD602JRZ Максимальные параметры и электрические характеристики
| Amplifier Type | Dual-channel variable gain amplifier |
| Number of Channels | 2 channels |
| Gain Range | −10 dB to +30 dB per channel |
| Maximum Gain | 31.07 dB |
| −3 dB Bandwidth | 35 MHz nominal |
| Bandwidth Dependence on Gain | Nominally independent of gain |
| Positive Supply Voltage | Up to +5.25 V |
| Negative Supply Voltage | Down to −5.25 V |
| Total Supply Span | Up to 10.5 V |
| Gain Control Logic Compatibility | TTL- and CMOS-compatible |
| Корпус | 16-lead SOIC |
| Тип монтажа | Surface mount |
| Рабочая температура | 0°C to +70°C |
Руководство по цоколевке AD602JRZ в корпусе 16-lead soic
Цоколевка для AD602JRZ (корпус 16-lead soic). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для AD602JRZ.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
AD602JRZ подходит для 6 применениеs: Ultrasound Imaging Receive Channels, Medical Ultrasound Echo Normalization, Dual-Channel Instrumentation, Wideband Sensor Signal Conditioning, Communications Receive Front Ends, Precision Analog Measurement Systems.
Ultrasound Imaging Receive Channels
The AD602JRZ fits ultrasound receive front ends because each channel provides adjustable gain from −10 dB to +30 dB across a nominal 35 MHz bandwidth. Place the amplifier between the transducer or receiver network and the ADC so returning echoes can be attenuated or amplified according to signal strength. Independent channel control permits asymmetric attenuation when two receive paths carry different levels. The broad bandwidth is essentially independent of gain, which simplifies system calibration, while low noise and low distortion help preserve weak echo information before digitization.
Рекомендуется
Medical Ultrasound Echo Normalization
The AD602JRZ can normalize variable-amplitude medical echo signals before conversion by an ADC. Its −10 dB lower limit provides attenuation in addition to the +30 dB upper range, allowing receive electronics to accommodate a broad spread of echo strengths. The 35 MHz nominal bandwidth supports wideband acoustic signal paths, while TTL- and CMOS-compatible gating control permits direct connection to digital control logic. Designers should account for the gain-control transfer characteristic and valid output swing when defining the ultrasound system’s attenuation calibration table.
Рекомендуется
Dual-Channel Instrumentation
The two independently adjustable channels of the AD602JRZ suit instrumentation that processes two related analog signals and requires separate attenuation settings. Its 35 MHz nominal bandwidth accommodates faster measurement nodes than many precision low-frequency amplifiers, while the −10 dB to +30 dB range provides practical control over signal level. The device is useful ahead of data converters or sampling circuits when transducer output amplitude changes substantially. Grounding and input-impedance management remain important because a wideband gain stage can magnify source noise as well as the intended signal.
Рекомендуется
Wideband Sensor Signal Conditioning
The AD602JRZ is appropriate for sensor interfaces whose output amplitude varies with stimulus or distance and needs electronic attenuation before downstream processing. Its −10 dB to +30 dB gain range permits coarse level control, and the nominal 35 MHz bandwidth is independent of gain, reducing the need to recalculate bandwidth across operating points. A TTL- and CMOS-compatible gating input simplifies control by digital systems. For high-frequency sensor cabling, use controlled impedance and short ground returns to prevent reflections and coupling from degrading the measured signal.
Рекомендуется
Communications Receive Front Ends
The AD602JRZ can serve as a wideband gain-control stage in communications equipment where received signal strength must be adjusted before filtering or conversion. Independent dual-channel control allows separate attenuation paths, and the 35 MHz nominal bandwidth supports high-speed analog nodes. The control input accepts TTL- and CMOS-compatible signals, which simplifies integration with a digital gain controller. Designers should verify the AD602 gain-control voltage range and signal bandwidth, minimize trace coupling, and maintain output swing so adjacent-channel or mixer overload is avoided.
Рекомендуется
Precision Analog Measurement Systems
The AD602JRZ fits measurement systems that require programmable signal level without sacrificing the nominal 35 MHz bandwidth. Its two channels provide separate attenuation commands, allowing calibration paths or differential acquisition chains to be adjusted independently. The −10 dB lower gain limit can prevent saturation in high-amplitude measurements, while the +30 dB maximum range supports amplification of smaller signals. Use short, shielded analog connections and carefully decoupled dual supplies to retain low-noise and low-distortion performance across the full gain range.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AD602JRZ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | AD602ARZ |
|---|---|---|
| Package | 16-lead SOIC | 16-lead SOIC |
| Brand | Analog Devices | Analog Devices |
| Number of Channels | 2 channels | 2 channels |
| Gain Range | −10 dB to +30 dB | −10 dB to +30 dB |
| Maximum Gain | 31.07 dB | 31.07 dB |
| −3 dB Bandwidth | 35 MHz nominal | 35 MHz nominal |
| Positive Supply Limit | +5.25 V | +5.25 V |
| Negative Supply Limit | −5.25 V | −5.25 V |
| Gain Control Logic | TTL- and CMOS-compatible | TTL- and CMOS-compatible |
Ключевые отличия
- Independent dual-channel gain adjustment (против AD602ARZ)
- Gain-independent wideband operation (против AD602ARZ)
- Direct digital control compatibility (против AD602ARZ)
Заметки по проектированию
Use separate positive and negative supply rails reaching no more than +5.25 V and −5.25 V. Place the positive and negative bypass capacitors close to the corresponding supply pins and follow the decoupling values and topology in the manufacturer datasheet. Because the nominal 35 MHz bandwidth can expose power-supply impedance and coupling, keep high-current return paths away from the analog inputs and gain-control nodes.
Route each channel as a controlled-impedance analog path and keep the gain-control traces away from input and output routing. Short ground returns and continuous reference planes reduce susceptibility to common-mode noise and high-frequency coupling. The two channels are independent, but maintaining consistent grounding, symmetry, and connector geometry helps prevent channel-to-channel differences from appearing as calibration errors.
Validate the source impedance, cable length, and input filtering against the amplifier’s 35 MHz nominal bandwidth. A gain-stage bandwidth is not the only limit in a wideband signal chain: source impedance can create gain peaking, reflections can distort step responses, and long interconnect can increase noise coupling. Use the datasheet gain-versus-frequency information when setting system bandwidth and do not assume the −3 dB point is independent of every external impedance.
Do not treat an AD600-family amplifier as an interchangeable AD602 device merely because both appear in the same datasheet and family. AD600 offers a 0 dB to +40 dB range, whereas AD602 provides −10 dB to +30 dB. Confirm gain-control polarity, range, transfer curve, supply conditions, and output limits before programming a replacement. Reel-code variants do not provide different electrical performance.
Информация о соответствии
The official product page and manufacturer datasheet links were identified, but explicit environmental, automotive-qualification, halogen-free, and conflict-minerals statements require confirmation from current manufacturer documentation.