AD713JN - Quad 9MHz Precision BiFET Op Amp | Analog Devices
Артикул: AD713JN ✓ АктивенAD713JN Обзор
A BiFET operational amplifier is an analog amplifier that uses field-effect transistor input stages for very high input impedance and low bias current. The AD713 belongs to the precision op amp hierarchy, where low offset, low drift, high common-mode rejection, and controlled gain are prioritized over wide output-swing capability. Its four matched channels make it useful where four similar amplifier functions are required on one board.
The AD713 provides 9 MHz small-signal bandwidth and a 10 V/µs slew rate, allowing accurate amplification of signals in the audio and low-frequency instrument range. Input bias current is typically 0.5 pA, while input voltage noise is 7 nV/√Hz. Typical input offset voltage is 0.3 mV, and the specified open-loop gain is 100 dB. The single-pole response settles to 0.01% within approximately 1 µs.
Its monolithic construction gives all four amplifiers close matching of both AC and DC characteristics. The amplifier operates from a total supply of up to 36 V while supporting a wide common-mode input range, making the AD713 suitable for bipolar signal chains. A unity-gain bandwidth near 9 MHz is substantially higher than that of the TL074, TL084, LF347, LT1058, and OPA404 circuits identified by Analog Devices as upgrade targets.
Typical applications include buffering 12-bit or 14-bit DAC and ADC outputs, audio preamplification, active filtering, sensor signal conditioning, laboratory instrumentation, and low-distortion voltage feedback stages. The AD713JN is appropriate where low bias current and matched quad-channel behavior are more important than rail-to-rail input or output operation.
The principal design consideration is supply headroom. The AD713 is not a rail-to-rail amplifier, so input and output signal levels must remain inside its linear input and output ranges, and suitable bypass capacitors should be placed close to the supply pins. Decoupling, grounding, and stability depend on the feedback network and the capacitive loading presented by the following stage.
This page combines the AD713JN electrical characteristics with drop-in replacement analysis, package details, and practical design guidance for precision analog signal chains. It also organizes application, comparison, and procurement information so engineers can identify a replacement without overlooking electrical compatibility.
Аналоги без доработки для AD713JN — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с AD713JN (тот же форм-фактор и посадочное место) — отличается по Amplifier Type, Package, Slew Rate, Mounting Type, Gain-Bandwidth Product.
AD713JNZ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TL074CN
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TL084CN
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LF347CN
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LT1058CN
✅ Прямая заменаУточнить цену
Открыть даташит →OPA404KP
✅ Прямая заменаУточнить цену
Открыть даташит →AD713JN Максимальные параметры и электрические характеристики
| Amplifier Type | Quad precision operational amplifier |
| Топология | Four AD711 BiFET amplifiers on a monolithic die |
| Number of Amplifiers | 4 channels |
| Gain-Bandwidth Product | 9 MHz |
| Slew Rate | 10 V/µs |
| Settling Time | Approximately 1 µs to 0.01% |
| Input Offset Voltage | 0.3 mV typical |
| Input Bias Current | 0.5 pA typical |
| Input Voltage Noise | 7 nV/√Hz |
| Open-Loop Gain | 100 dB typical |
| Maximum Total Supply Voltage | 36 V |
| Common-Mode Rejection Ratio | 100 dB typical |
| Power Supply Rejection Ratio | 100 dB typical |
| Диапазон рабочих температур | 0°C to +70°C |
| Корпус | 14-lead plastic DIP |
| Тип монтажа | Through-hole |
| Lead-Free Status | unknown |
| RoHS Compliance | unknown |
Конфигурация выводов AD713JN
| Контакт 1 | OUT1 — Amplifier 1 output |
| Контакт 2 | -IN1 — Amplifier 1 inverting input |
| Контакт 3 | +IN1 — Amplifier 1 non-inverting input |
| Контакт 4 | V- — Negative supply connection |
| Контакт 5 | +IN2 — Amplifier 2 non-inverting input |
| Контакт 6 | -IN2 — Amplifier 2 inverting input |
| Контакт 7 | OUT2 — Amplifier 2 output |
| Контакт 8 | OUT3 — Amplifier 3 output |
| Контакт 9 | -IN3 — Amplifier 3 inverting input |
| Контакт 10 | +IN3 — Amplifier 3 non-inverting input |
| Контакт 11 | V+ — Positive supply connection |
| Контакт 12 | +IN4 — Amplifier 4 non-inverting input |
| Контакт 13 | -IN4 — Amplifier 4 inverting input |
| Контакт 14 | OUT4 — Amplifier 4 output |
Типичное применение
AD713JN подходит для 6 применениеs: High-Resolution ADC Output Buffering, Precision DAC Output Buffering, Audio Preamplifier and Mixer, Active Filtering and Frequency Response Conditioning, Industrial Sensor Signal Conditioning, Laboratory and Instrumentation Buffering.
High-Resolution ADC Output Buffering
The AD713JN fits immediately after 12-bit or 14-bit SAR and mixed-signal converters because its 9 MHz gain-bandwidth product and 10 V/µs slew rate provide rapid transitions between code levels. The approximately 1 µs settling to 0.01% characteristic is especially useful when the acquisition interval must accommodate full-scale settling. Connect each converter output to the non-inverting input of one amplifier and use a small isolation resistor at the output when the ADC presents a capacitive sampling network. The amplifier's 0.5 pA typical input bias current minimizes disturbance of high-impedance converter nodes, while its 7 nV/√Hz noise supports low-level signal chains. Place supply bypass capacitors close to pins 4 and 11 and keep feedback routing compact.
Рекомендуется
Precision DAC Output Buffering
A quad DAC signal chain can use the four AD713JN amplifiers to provide low-impedance drive, isolation, and gain adjustment. The device's 9 MHz bandwidth and 10 V/µs slew rate allow it to follow fast full-scale DAC transitions, while the approximately 1 µs settling to 0.01% supports accurate settling in instrument and audio systems. Its typical 0.5 pA input bias current is beneficial when the DAC output includes high-value feedback resistors. Use the amplifier in a voltage-follower configuration when unity gain and maximum bandwidth are needed, or add a feedback network for gain and filtering. Verify output-current capability, output swing, and capacitive-load stability against the specific DAC output impedance and cable loading.
Рекомендуется
Audio Preamplifier and Mixer
The AD713JN can implement four matched low-noise preamplifier or mixer channels in professional and laboratory audio equipment. Its 9 MHz gain-bandwidth product provides more bandwidth than conventional 74-family audio amplifiers, while the 10 V/µs slew rate reduces distortion on larger transients. Typical input bias current of 0.5 pA preserves the amplitude of high-impedance source signals, and the common monolithic die improves matching among identical microphone or line-input channels. Use non-inverting stages where low noise and phase response are priorities, and add RC low-pass stages for bandwidth limiting. Confirm the available output swing, load impedance, and channel-to-channel matching requirements, particularly in balanced or transformer-coupled audio paths.
Рекомендуется
Active Filtering and Frequency Response Conditioning
The four matched channels of the AD713JN are suitable for active low-pass, high-pass, band-pass, and notch-filter stages where consistent component behavior simplifies calibration. A 9 MHz gain-bandwidth product allows useful loop gain well above the audio range, and the 10 V/µs slew rate supports rapid signal transitions without immediately dominating the filter response. The monolithic construction helps reduce channel-to-channel variation in multichannel filters. Choose resistor and capacitor tolerances appropriate to the required cutoff accuracy, and confirm the amplifier's open-loop gain and phase response against the filter topology. A small isolation resistor may be required at the output when driving a long cable or additional capacitive input loading.
Рекомендуется
Industrial Sensor Signal Conditioning
The AD713JN is appropriate for conditioning signals from high-impedance sensors, bridges, and instrumentation transducers in industrial measurement systems. Its 0.5 pA typical input bias current minimizes loading, while the 100 dB typical common-mode rejection helps suppress differential signals riding on larger common-mode voltages. Four amplifiers on one monolithic die provide closely matched channels for differential amplifiers, instrumentation stages, or multiple sensor inputs. Because the device is not rail-to-rail, the sensor excitation and signal levels must remain inside the input common-mode range, and the output must remain inside the linear swing limits. Add input protection, shielding, and guarded grounding to prevent leakage from cables or contaminated surfaces from exceeding the low-current capability.
Рекомендуется
Laboratory and Instrumentation Buffering
The AD713JN supports precision bench instruments, measurement interfaces, and laboratory buffer stages where input loading must remain low and signal transitions must settle rapidly. The 9 MHz bandwidth and 10 V/µs slew rate provide useful dynamic performance, while the monolithic quad layout reduces mismatch between nominally identical channels. Voltage-follower stages can isolate a source from subsequent instrumentation, and inverting or non-inverting gain stages can add configurable attenuation or amplification. Keep input leads short, use guarding for very high impedance sources, and decouple the power pins locally. When driving oscilloscope inputs, probe capacitance, or long cable runs, include output isolation and verify stability across the full input range.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AD713JN — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | AD713JNZ | TL074CN | TL084CN | LF347CN | LT1058CN | OPA404KP |
|---|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Texas Instruments |
| Package | 14-lead plastic DIP | 14-lead plastic DIP | 14-lead plastic DIP | 14-lead plastic DIP | 14-lead plastic DIP | 14-lead plastic DIP | 14-lead plastic DIP |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 4 | 4 |
Ключевые отличия
- High-speed precision in a four-channel monolithic device (против TL084CN)
- Matched AC and DC characteristics across four amplifiers (против TL074CN)
- Very low input bias current for high-impedance sources (против LF347CN)
- Fast 0.01% settling supports higher-resolution conversion chains (против LT1058CN)
- Higher speed with closely matched quad channels (против OPA404KP)
Заметки по проектированию
Place the positive and negative supply bypass capacitors immediately beside pins 11 and 4. Because the AD713JN is a through-hole DIP in a high-gain analog signal path, long supply traces can add inductance and reduce effective decoupling at high frequency. Keep the analog ground return close to the device, avoid sharing narrow return paths with switching-current loops, and route the four input and output channels away from clock and power-converter nodes.
Do not treat the AD713JN as a rail-to-rail amplifier. Its input common-mode range and output swing must remain inside the linear operating region specified by the Analog Devices AD713 datasheet. In a ±15 V analog system this is rarely a problem, but in a 3.3 V or 5 V system the available headroom can be insufficient. Verify the actual signal excursions, output load, and common-mode voltage before finalizing the supply arrangement.
When driving an ADC input, cable, or other capacitive load, add a small isolation resistor between the amplifier output and the load. This limits the capacitive feedback current that can destabilize the loop. A voltage-follower configuration provides maximum bandwidth, while added noise gain reduces bandwidth and improves phase margin. Confirm the settling requirement against the 9 MHz gain-bandwidth product rather than relying on slew rate alone.
Keep the four amplifier channels symmetrical when channel matching is important. Use matched feedback resistors, equal input routing lengths, and identical reference connections for corresponding channels. Minimize parasitic capacitance on the non-inverting inputs because the AD713's low bias current makes high-impedance nodes susceptible to leakage. Guard or shield sensitive inputs if nearby humidity, connector contamination, or flux residue is possible.
Информация о соответствии
Compliance information was not stated in the retrieved product materials. Confirm current RoHS, REACH, lead-free, and halogen-free declarations for the exact ordering code before use in regulated production.