Analog Devices

AD713JN - Quad 9MHz Precision BiFET Op Amp | Analog Devices

部品番号: AD713JN ✓ 生産中
0.3 mV typical Vdss 0.5 pA typical Id 14-lead plastic DIP Package
MOQ: 1 |

AD713JN 概要

The Analog Devices AD713JN is a quad precision BiFET operational amplifier combining four AD711 amplifiers on one monolithic die, with 9 MHz gain-bandwidth product, 10 V/µs slew rate, and a 14-lead plastic DIP package. The device combines low input bias current, high open-loop gain, and fast settling within a common die, improving channel-to-channel matching in instrumentation and signal-conditioning circuits.

A BiFET operational amplifier is an analog amplifier that uses field-effect transistor input stages for very high input impedance and low bias current. The AD713 belongs to the precision op amp hierarchy, where low offset, low drift, high common-mode rejection, and controlled gain are prioritized over wide output-swing capability. Its four matched channels make it useful where four similar amplifier functions are required on one board.

The AD713 provides 9 MHz small-signal bandwidth and a 10 V/µs slew rate, allowing accurate amplification of signals in the audio and low-frequency instrument range. Input bias current is typically 0.5 pA, while input voltage noise is 7 nV/√Hz. Typical input offset voltage is 0.3 mV, and the specified open-loop gain is 100 dB. The single-pole response settles to 0.01% within approximately 1 µs.

Its monolithic construction gives all four amplifiers close matching of both AC and DC characteristics. The amplifier operates from a total supply of up to 36 V while supporting a wide common-mode input range, making the AD713 suitable for bipolar signal chains. A unity-gain bandwidth near 9 MHz is substantially higher than that of the TL074, TL084, LF347, LT1058, and OPA404 circuits identified by Analog Devices as upgrade targets.

Typical applications include buffering 12-bit or 14-bit DAC and ADC outputs, audio preamplification, active filtering, sensor signal conditioning, laboratory instrumentation, and low-distortion voltage feedback stages. The AD713JN is appropriate where low bias current and matched quad-channel behavior are more important than rail-to-rail input or output operation.

The principal design consideration is supply headroom. The AD713 is not a rail-to-rail amplifier, so input and output signal levels must remain inside its linear input and output ranges, and suitable bypass capacitors should be placed close to the supply pins. Decoupling, grounding, and stability depend on the feedback network and the capacitive loading presented by the following stage.

This page combines the AD713JN electrical characteristics with drop-in replacement analysis, package details, and practical design guidance for precision analog signal chains. It also organizes application, comparison, and procurement information so engineers can identify a replacement without overlooking electrical compatibility.

ドロップイン代替品: AD713JN — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: AD713JN (同一形状・フットプリント) — 相違点: Amplifier Type, Package, Slew Rate, Mounting Type, Gain-Bandwidth Product.

Analog Devices
Amplifier Type: JFET-input precision operational amplifier
Package: 14-pin PDIP, 0.300 in (7.62 mm) pitch
Slew Rate: 13 V/us
比較対象 AD713JN →
Texas Instruments
Amplifier Type: Quad High-Speed Precision Difet Operational Amplifier
Package: 14-PDIP
Slew Rate: 35 V/us
比較対象 AD713JN →

AD713JNZ

✅ ドロップイン
📦 14-lead plastic DIP
Lead-finish ordering designation differs; gain-bandwidth product remains 9 MHz and slew rate remains 10 V/µs

📋 参考代替品(カタログ未掲載)

TL074CN

✅ ドロップイン
📦 14-lead plastic DIP
Gain-bandwidth product is lower than the AD713's 9 MHz, so settling and slew-rate performance are reduced

📋 参考代替品(カタログ未掲載)

TL084CN

✅ ドロップイン
📦 14-lead plastic DIP
Standard 14-pin quad FET-input arrangement is retained, while bandwidth and slew rate are below the AD713's 9 MHz and 10 V/µs

📋 参考代替品(カタログ未掲載)

LF347CN

✅ ドロップイン
📦 14-lead plastic DIP
Uses the conventional 14-pin quad layout but has lower bandwidth and slew rate than the AD713

📋 参考代替品(カタログ未掲載)

LT1058CN

✅ ドロップイン
Analog Devices
📦 14-lead plastic DIP
4 channels · JFET-input precision operational amplifier · 5 MHz · 13 V/us · 10 V/us · 600 uV maximum for LT1058 · -20 V to +20 V · 1.7 mA

価格はお問い合わせください

データシートを見る →

OPA404KP

✅ ドロップイン
Texas Instruments
📦 14-lead plastic DIP
Quad High-Speed Precision Difet Operational Amplifier · 4 · 6.4 MHz · 35 V/us · +/-750 uV · +/-4 pA · 0.01% settling spec (datasheet value) · 10 V

価格はお問い合わせください

データシートを見る →

AD713JN 最大定格&電気的特性

Amplifier Type Quad precision operational amplifier
トポロジー Four AD711 BiFET amplifiers on a monolithic die
Number of Amplifiers 4 channels
Gain-Bandwidth Product 9 MHz
Slew Rate 10 V/µs
Settling Time Approximately 1 µs to 0.01%
Input Offset Voltage 0.3 mV typical
Input Bias Current 0.5 pA typical
Input Voltage Noise 7 nV/√Hz
Open-Loop Gain 100 dB typical
Maximum Total Supply Voltage 36 V
Common-Mode Rejection Ratio 100 dB typical
Power Supply Rejection Ratio 100 dB typical
動作温度範囲 0°C to +70°C
パッケージ 14-lead plastic DIP
実装タイプ Through-hole
Lead-Free Status unknown
RoHS Compliance unknown

AD713JN ピン構成

DIP-14 Package Pinout Diagram DIP-14 14-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 DIP-14
ピン 1 OUT1 — Amplifier 1 output
ピン 2 -IN1 — Amplifier 1 inverting input
ピン 3 +IN1 — Amplifier 1 non-inverting input
ピン 4 V- — Negative supply connection
ピン 5 +IN2 — Amplifier 2 non-inverting input
ピン 6 -IN2 — Amplifier 2 inverting input
ピン 7 OUT2 — Amplifier 2 output
ピン 8 OUT3 — Amplifier 3 output
ピン 9 -IN3 — Amplifier 3 inverting input
ピン 10 +IN3 — Amplifier 3 non-inverting input
ピン 11 V+ — Positive supply connection
ピン 12 +IN4 — Amplifier 4 non-inverting input
ピン 13 -IN4 — Amplifier 4 inverting input
ピン 14 OUT4 — Amplifier 4 output

主な用途

AD713JN の用途: 6 件s: High-Resolution ADC Output Buffering, Precision DAC Output Buffering, Audio Preamplifier and Mixer, Active Filtering and Frequency Response Conditioning, Industrial Sensor Signal Conditioning, Laboratory and Instrumentation Buffering.

📊

High-Resolution ADC Output Buffering

The AD713JN fits immediately after 12-bit or 14-bit SAR and mixed-signal converters because its 9 MHz gain-bandwidth product and 10 V/µs slew rate provide rapid transitions between code levels. The approximately 1 µs settling to 0.01% characteristic is especially useful when the acquisition interval must accommodate full-scale settling. Connect each converter output to the non-inverting input of one amplifier and use a small isolation resistor at the output when the ADC presents a capacitive sampling network. The amplifier's 0.5 pA typical input bias current minimizes disturbance of high-impedance converter nodes, while its 7 nV/√Hz noise supports low-level signal chains. Place supply bypass capacitors close to pins 4 and 11 and keep feedback routing compact.

🎵

Precision DAC Output Buffering

A quad DAC signal chain can use the four AD713JN amplifiers to provide low-impedance drive, isolation, and gain adjustment. The device's 9 MHz bandwidth and 10 V/µs slew rate allow it to follow fast full-scale DAC transitions, while the approximately 1 µs settling to 0.01% supports accurate settling in instrument and audio systems. Its typical 0.5 pA input bias current is beneficial when the DAC output includes high-value feedback resistors. Use the amplifier in a voltage-follower configuration when unity gain and maximum bandwidth are needed, or add a feedback network for gain and filtering. Verify output-current capability, output swing, and capacitive-load stability against the specific DAC output impedance and cable loading.

🎧

Audio Preamplifier and Mixer

The AD713JN can implement four matched low-noise preamplifier or mixer channels in professional and laboratory audio equipment. Its 9 MHz gain-bandwidth product provides more bandwidth than conventional 74-family audio amplifiers, while the 10 V/µs slew rate reduces distortion on larger transients. Typical input bias current of 0.5 pA preserves the amplitude of high-impedance source signals, and the common monolithic die improves matching among identical microphone or line-input channels. Use non-inverting stages where low noise and phase response are priorities, and add RC low-pass stages for bandwidth limiting. Confirm the available output swing, load impedance, and channel-to-channel matching requirements, particularly in balanced or transformer-coupled audio paths.

🎛️

Active Filtering and Frequency Response Conditioning

The four matched channels of the AD713JN are suitable for active low-pass, high-pass, band-pass, and notch-filter stages where consistent component behavior simplifies calibration. A 9 MHz gain-bandwidth product allows useful loop gain well above the audio range, and the 10 V/µs slew rate supports rapid signal transitions without immediately dominating the filter response. The monolithic construction helps reduce channel-to-channel variation in multichannel filters. Choose resistor and capacitor tolerances appropriate to the required cutoff accuracy, and confirm the amplifier's open-loop gain and phase response against the filter topology. A small isolation resistor may be required at the output when driving a long cable or additional capacitive input loading.

🏭

Industrial Sensor Signal Conditioning

The AD713JN is appropriate for conditioning signals from high-impedance sensors, bridges, and instrumentation transducers in industrial measurement systems. Its 0.5 pA typical input bias current minimizes loading, while the 100 dB typical common-mode rejection helps suppress differential signals riding on larger common-mode voltages. Four amplifiers on one monolithic die provide closely matched channels for differential amplifiers, instrumentation stages, or multiple sensor inputs. Because the device is not rail-to-rail, the sensor excitation and signal levels must remain inside the input common-mode range, and the output must remain inside the linear swing limits. Add input protection, shielding, and guarded grounding to prevent leakage from cables or contaminated surfaces from exceeding the low-current capability.

🖥️

Laboratory and Instrumentation Buffering

The AD713JN supports precision bench instruments, measurement interfaces, and laboratory buffer stages where input loading must remain low and signal transitions must settle rapidly. The 9 MHz bandwidth and 10 V/µs slew rate provide useful dynamic performance, while the monolithic quad layout reduces mismatch between nominally identical channels. Voltage-follower stages can isolate a source from subsequent instrumentation, and inverting or non-inverting gain stages can add configurable attenuation or amplification. Keep input leads short, use guarding for very high impedance sources, and decouple the power pins locally. When driving oscilloscope inputs, probe capacitance, or long cable runs, include output isolation and verify stability across the full input range.

What is the AD713JN?
The AD713JN is a quad precision BiFET operational amplifier containing four AD711 amplifier sections on one monolithic die. According to the Analog Devices AD713 datasheet, the device provides 9 MHz gain-bandwidth product, a 10 V/µs slew rate, low input bias current, and close AC and DC matching between channels. It is supplied in a 14-lead plastic DIP package for through-hole instrumentation and legacy circuit designs.
What are the key specifications of AD713JN that engineers should know?
The AD713JN combines four precision BiFET op amps with a 9 MHz gain-bandwidth product and 10 V/µs slew rate. According to the Analog Devices AD713 datasheet, typical input bias current is 0.5 pA, input voltage noise is 7 nV/√Hz, input offset voltage is 0.3 mV, and open-loop gain is 100 dB. Its four amplifiers share one die, providing tighter channel matching than four independently selected discrete amplifiers.
What can replace the AD713JN?
The AD713JN can be replaced most directly by a pin-compatible 14-pin quad amplifier such as the TL074CN or TL084CN when the lower bandwidth of those devices is acceptable. The Analog Devices AD713 datasheet identifies the TL074, TL084, LT1058, LF347, and OPA404 as performance upgrade targets. Every substitute still requires verification of bandwidth, slew rate, noise, offset, supply range, and stability.
Is the AD713JN pin compatible with the TL074CN?
The AD713JN and TL074CN both use the conventional 14-lead quad-op-amp pin arrangement, so the TL074CN is a practical drop-in candidate on a correctly designed board. The AD713 is faster, with a 9 MHz gain-bandwidth product and 10 V/µs slew rate, while the TL074 is generally slower. Confirm input offset, noise, stability with capacitive loads, and output swing before replacing an existing design.
What is the difference between AD713JN and AD713JNZ?
AD713JN and AD713JNZ identify the AD713 family with different finish or ordering designations, so the critical distinction is the exact package and lead-finish configuration ordered. The AD713JN is a 14-lead plastic DIP device, while AD713JNZ is the corresponding lead-free ordering designation identified for the family. Confirm the mechanical drawing, terminal finish, and bill of materials requirements against the Analog Devices ordering guide.
Is the AD713JN suitable for buffering 12-bit and 14-bit ADCs?
Yes, the AD713JN is specifically suited to buffering 12-bit and 14-bit DAC or ADC outputs. The Analog Devices AD713 datasheet highlights its approximately 1 µs settling to 0.01%, 9 MHz bandwidth, and 10 V/µs slew rate, which help preserve full-scale code accuracy during transitions. Use short feedback traces, a suitable output isolation resistor for capacitive loads, and local supply bypassing.
What is the operating voltage range of AD713JN?
The AD713JN supports a maximum total supply voltage of 36 V and can be operated with positive, negative, or split bipolar supplies. The Analog Devices AD713 datasheet defines the absolute maximum and operating conditions, including the requirement to keep the total voltage between the positive and negative rails within the stated limit. Because it is not rail-to-rail, signal swing must also remain within the linear input and output ranges.
When should I choose the AD713JN over a TL084CN?
Choose the AD713JN when precision, low input bias current, fast settling, and channel matching matter more than cost or availability. The AD713 offers 9 MHz bandwidth and 10 V/µs slew rate with closely matched AC and DC characteristics, whereas the TL084 is a lower-bandwidth general-purpose FET-input amplifier. For audio filtering, instrumentation, or ADC and DAC buffering, the faster AD713 provides more settling margin.
What is the best TI equivalent for the AD713JN?
The OPA404KP is a relevant 14-lead DIP alternative because the Analog Devices AD713 datasheet identifies the OPA404 family as a performance upgrade target. It is not an exact electrical substitute: the OPA404 is specified for lower offset and lower distortion in precision applications, while the AD713 emphasizes high speed, low bias current, and closely matched quad channels. Review offset, noise, bias current, bandwidth, and output-swing requirements.
Where can I download the AD713JN datasheet PDF?
The official AD713 datasheet PDF is available from Analog Devices at the datasheet link on this page. The document contains the AD713 family electrical characteristics, typical performance graphs, pin configuration, package dimensions, ordering information, and application guidance. For the AD713JN specifically, use the package and temperature-ordering tables to confirm that the ceramic DIP and plastic DIP variants are distinguished correctly.
Where can I find the AD713JN pinout?
The AD713JN pinout is shown in the Analog Devices AD713 datasheet and in the package diagram associated with this page. It is a 14-lead DIP arranged as a standard quad operational amplifier: pins 1, 7, 8, and 14 are outputs; pins 2, 6, 9, and 13 are inverting inputs; pins 3, 5, 10, and 12 are non-inverting inputs; pin 4 is the negative supply and pin 11 is the positive supply.
Can the AD713JN drive a capacitive load?
The AD713JN can drive capacitive loads only with care because a high-gain operational amplifier driving a capacitive load can reduce phase margin and produce ringing or oscillation. Place a small isolation resistor between the amplifier output and the capacitive input, and keep feedback traces short. If the load is highly capacitive or the feedback factor is very high, verify stability against the amplifier response and load capacitance.
Where can I buy the AD713JN online?
Use the Request a Quote form on this page to ask for AD713JN availability, lot traceability, and delivery terms. The component is offered as a 14-lead plastic DIP operational amplifier, so confirm the required package, operating-temperature grade, and acceptable lead configuration before releasing an order. For production quantities, request date codes and any lot-specific traceability documentation.
What is the lead time for AD713JN?
The current lead time for AD713JN should be confirmed through the Request a Quote form on this page. Lead time can vary with package configuration, order volume, and factory scheduling, so confirm the quantity, target date, and assembly schedule with the quote. If your design permits an alternate quad BiFET amplifier, request that option in the same inquiry for supply-risk planning.
Is the AD713JN in stock?
Stock status for AD713JN is handled through the Request a Quote form on this page rather than through static availability text. Submit the required quantity, target delivery date, and acceptable package configuration to obtain current allocation information. Because AD713 is an established through-hole precision amplifier, buyers should also request an approved pin-compatible alternative for second-source qualification.

エンジニアリング参考データ: AD713JN — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the AD713JN when a legacy 14-pin DIP design needs four low-bias-current BiFET amplifiers with 9 MHz bandwidth, 10 V/µs slew rate, and close channel matching. It is particularly appropriate for buffering 12-bit or 14-bit converters, precision audio stages, instrumentation, and matched active filters. Select TL074CN or TL084CN when a standard low-cost quad amplifier is sufficient and lower bandwidth is acceptable. Consider OPA404KP when offset voltage and distortion dominate the application rather than speed and channel matching. LT1058CN is appropriate when precision offset performance is the priority, but its dynamic characteristics must be checked against the required settling time. For every alternative, verify supply range, input common-mode range, output swing, noise, stability with capacitive loading, and the exact physical dimensions before releasing a production order.

代替品との比較

パラメータ この製品 AD713JNZ TL074CN TL084CN LF347CN LT1058CN OPA404KP
Brand Analog Devices Analog Devices Texas Instruments Texas Instruments Texas Instruments Analog Devices Texas Instruments
Package 14-lead plastic DIP 14-lead plastic DIP 14-lead plastic DIP 14-lead plastic DIP 14-lead plastic DIP 14-lead plastic DIP 14-lead plastic DIP
Number of Amplifiers 4 4 4 4 4 4 4

主な差別化要因

  • High-speed precision in a four-channel monolithic device (vs TL084CN)
  • Matched AC and DC characteristics across four amplifiers (vs TL074CN)
  • Very low input bias current for high-impedance sources (vs LF347CN)
  • Fast 0.01% settling supports higher-resolution conversion chains (vs LT1058CN)
  • Higher speed with closely matched quad channels (vs OPA404KP)

設計ノート

Place the positive and negative supply bypass capacitors immediately beside pins 11 and 4. Because the AD713JN is a through-hole DIP in a high-gain analog signal path, long supply traces can add inductance and reduce effective decoupling at high frequency. Keep the analog ground return close to the device, avoid sharing narrow return paths with switching-current loops, and route the four input and output channels away from clock and power-converter nodes.

Do not treat the AD713JN as a rail-to-rail amplifier. Its input common-mode range and output swing must remain inside the linear operating region specified by the Analog Devices AD713 datasheet. In a ±15 V analog system this is rarely a problem, but in a 3.3 V or 5 V system the available headroom can be insufficient. Verify the actual signal excursions, output load, and common-mode voltage before finalizing the supply arrangement.

When driving an ADC input, cable, or other capacitive load, add a small isolation resistor between the amplifier output and the load. This limits the capacitive feedback current that can destabilize the loop. A voltage-follower configuration provides maximum bandwidth, while added noise gain reduces bandwidth and improves phase margin. Confirm the settling requirement against the 9 MHz gain-bandwidth product rather than relying on slew rate alone.

Keep the four amplifier channels symmetrical when channel matching is important. Use matched feedback resistors, equal input routing lengths, and identical reference connections for corresponding channels. Minimize parasitic capacitance on the non-inverting inputs because the AD713's low bias current makes high-impedance nodes susceptible to leakage. Guard or shield sensitive inputs if nearby humidity, connector contamination, or flux residue is possible.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

Compliance information was not stated in the retrieved product materials. Confirm current RoHS, REACH, lead-free, and halogen-free declarations for the exact ordering code before use in regulated production.

データ検証日: 2026-11-18 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

AD713JN datasheet AD713JN datasheet pdf AD713JN pinout AD713JN specifications AD713JN equivalent AD713JN replacement AD713JN cross reference AD713JN vs TL074CN AD713JN vs TL084CN AD713JN price AD713JN stock Analog Devices AD713JN AD713JN 14 pin DIP AD713JN application circuit AD713JN ADC DAC buffer

関連部品&用語

Analog Devices AD713JN AD713JNZ AD713 AD711 TL074CN TL084CN LF347CN LT1058CN OPA404KP operational amplifier precision op amp quad op amp BiFET op amp field-effect transistor input analog IC semiconductor gain-bandwidth product slew rate input bias current input offset voltage settling time common-mode rejection ratio 14-lead plastic DIP through-hole package ADC buffering DAC buffering active filter audio preamplifier sensor signal conditioning instrumentation
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示