AD7440BRM - 10-Bit 1 MSPS Differential SAR ADC | Analog Devices
Артикул: AD7440BRM ✓ АктивенAD7440BRM Обзор
An SAR ADC is a sampling analog-to-digital converter that compares the input voltage with an internal DAC and performs successive approximation during each conversion. As a type of ADC, it belongs to the data-converter hierarchy and ultimately to the broader semiconductor and signal-processing markets. Its SAR architecture is well suited to precision measurement, industrial instrumentation, and control systems where modest conversion speed and compact implementation are more important than very high sample rates.
The AD7440 offers 10-bit resolution at 1 MSPS through its fully differential input architecture. Differential operation helps reject common-mode voltage and reduces sensitivity to noise when the source is balanced around a common reference level. The converter can operate from either a 3 V or 5 V supply, allowing it to fit both low-voltage embedded systems and conventional industrial analog circuits.
Low power is a core operating characteristic. According to the AD7440 family information, operation from a 3 V supply permits maximum power consumption of 4 mW at a throughput rate of 1 MSPS. This low figure reflects the use of advanced low-power design techniques. The SAR conversion principle supports repeated sampling and acquisition while limiting the average power required from the supply.
Typical applications include industrial process measurement, sensor-interface circuits, portable instrumentation, battery-powered data acquisition, motor and power-system monitoring, and embedded control systems. The differential input can simplify conditioning around sensors whose outputs are centered on a reference voltage rather than ground. The SPI-compatible interface also makes the device suitable for systems that already include a microcontroller or another serial master.
When laying out the circuit, treat the analog input, reference, and ground paths as sensitive nodes. Keep input and reference routing short, use a quiet ground plane, and place input and reference bypass capacitors close to the device. The 8-pin MSOP footprint supports compact designs, but careful decoupling and return-current control remain necessary to realize the converter's specified performance.
This page combines manufacturer specifications, commercial availability, replacement guidance, package information, and practical design notes. It also distinguishes a true drop-in replacement from a higher-resolution family member and identifies which technical details should be confirmed in the manufacturer datasheet before a design is released.
Аналоги без доработки для AD7440BRM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с AD7440BRM (тот же форм-фактор и посадочное место) — отличается по Operating Temperature, Resolution.
AD7440BRM-REEL7
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD7440BRMZ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD7450ARZ-REEL
✅ Прямая заменаУточнить цену
Открыть даташит →AD7440BRM Максимальные параметры и электрические характеристики
| Converter Type | Successive-approximation ADC (SAR) |
| Разрешение | 10 bit |
| Частота дискретизации | 1 MSPS |
| Input Architecture | Fully differential, 1 channel |
| Напряжение питания | 3 V or 5 V |
| Maximum Power Consumption | 4 mW at 1 MSPS with a 3 V supply |
| Интерфейс | SPI |
| Рабочая температура | -40°C to +85°C |
| Корпус | 8-pin MSOP (RM-8) |
| Тип монтажа | Surface mount |
| Analog Input Count | 1 channel |
| Output Word Width | 10 bit |
| Conversion Throughput | 1 million samples per second |
Руководство по цоколевке AD7440BRM в корпусе 8-pin msop (rm-8)
Цоколевка для AD7440BRM (корпус 8-pin msop (rm-8)). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для AD7440BRM.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
AD7440BRM подходит для 6 применениеs: Industrial Sensor Signal Acquisition, Battery-Powered Portable Instrument, Process Control Monitoring, Power System Monitoring, Embedded Control Data Acquisition, Precision Diagnostic Equipment.
Industrial Sensor Signal Acquisition
The AD7440BRM fits industrial sensor acquisition when the measured signal requires 10-bit resolution and a throughput of up to 1 MSPS. Its fully differential input is useful when the sensor output is centered around a common-mode reference, helping the converter process the intended differential voltage rather than a large shared voltage. Place the converter close to the sensor-conditioning network, keep the input traces short, and bypass the reference locally. The maximum 4 mW power consumption at 1 MSPS from a 3 V supply also limits the converter's contribution to a distributed measurement node's thermal and battery budget.
Рекомендуется
Battery-Powered Portable Instrument
The AD7440BRM is appropriate for battery-powered portable instruments because its 10-bit SAR converter can operate from 3 V and consumes no more than 4 mW at 1 MSPS. The SAR architecture provides a practical balance between conversion rate, resolution, and power when continuous acquisition is not required. A duty-cycled acquisition strategy can reduce average energy use further by keeping the converter and its reference inactive between measurements. Designers should include the external reference, protection network, and serial controller in the complete power calculation rather than evaluating only the ADC.
Рекомендуется
Process Control Monitoring
The AD7440BRM can serve as the analog front end of a process-control monitoring channel when 1 MSPS throughput is adequate for dynamic pressure, temperature, or position signals. A fully differential input supports conditioning stages that reject common-mode noise, while the SPI-compatible interface allows a controller to collect conversion results over a short serial link. For reliable sampling, establish a clean analog ground, keep the differential input route compact, and place reference bypass capacitance next to the converter. The 10-bit code width gives 1024 quantization levels across the selected input and reference range.
Рекомендуется
Power System Monitoring
The AD7440BRM is suitable for monitoring a scaled power-system voltage when the design requires differential input handling and a 1 MSPS sampling ceiling. The converter can capture a conditioned representation of bus or converter output while its SPI interface transfers results to a supervisory controller. A differential front end helps reject shared switching-node noise, but the analog and digital grounds still need careful partitioning. Use the lowest practical input bandwidth, locate input filtering close to the device, and verify that every attenuated signal remains within the datasheet's common-mode and differential-range limits.
Рекомендуется
Embedded Control Data Acquisition
The AD7440BRM fits embedded control systems that periodically acquire an analog command, diagnostic, or feedback value and communicate it through a serial interface. At 10-bit resolution and 1 MSPS throughput, the converter provides ample speed for many control loops while keeping the circuit compact in an 8-pin MSOP. The SPI-compatible interface supports connection to a microcontroller-based controller, while operation from 3 V or 5 V accommodates multiple system rails. For noise-sensitive control nodes, provide local reference bypassing and route digital clock and serial signals away from the differential input path.
Рекомендуется
Precision Diagnostic Equipment
The AD7440BRM can be used in diagnostic equipment when 10-bit resolution is sufficient for the measured quantity and low-power SAR conversion is valuable. The fully differential input permits the front end to present a centered signal, and the 1 MSPS maximum rate supports acquisition of rapidly changing diagnostic waveforms without requiring a high-power flash converter. A 10-bit result provides 1024 codes, so the useful measurement resolution still depends on input-range selection, reference accuracy, noise, and calibration. For tests requiring finer quantization, evaluate the 12-bit AD7450A family member before finalizing the analog front end.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AD7440BRM — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | AD7440BRM-REEL7 | AD7440BRMZ | AD7450A |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin MSOP (RM-8) | 8-pin MSOP (RM-8) | 8-pin MSOP (RM-8) | 8-pin MSOP (RM-8) |
| Resolution | 10 bit | 10 bit | 10 bit | 12 bit |
| Sampling Rate | 1 MSPS | 1 MSPS | 1 MSPS | 1 MSPS class |
| Input Architecture | Fully differential, 1 channel | Fully differential, 1 channel | Fully differential, 1 channel | Fully differential, 1 channel |
| Supply Voltage | 3 V or 5 V | 3 V or 5 V | 3 V or 5 V | 3 V or 5 V |
| Interface | SPI | SPI | SPI | SPI |
| Key Difference | Baseline 10-bit AD7440 order code | Same electrical performance; different reel order code | Same electrical performance; different lead-finish order code | Resolution increases from 10 bits to 12 bits |
Ключевые отличия
- Low converter power at full throughput (против AD7450A)
- Direct same-order-code family substitutions (против AD7440BRM-REEL7)
- Straightforward footprint-compatible upgrade path (против AD7450A)
Заметки по проектированию
Route the fully differential input as a compact pair with closely matched geometry, and connect the two lines to their respective analog input pins without adding unnecessary stubs. Place input filtering and reference-bypass capacitors close to the AD7440BRM. Keep the SPI clock and data traces on the opposite side of the component from the analog input. A continuous ground plane is preferred, with analog and digital return currents kept from sharing high-current paths.
Do not assume that a 10-bit converter delivers 10-bit absolute system accuracy. The usable result also depends on reference-voltage accuracy, input noise, source impedance, differential common-mode range, and PCB contamination. Confirm the signal's common-mode voltage against the Analog Devices manufacturer datasheet before designing the amplifier or sensor front end. The 3 V or 5 V supply selection must also remain compatible with the chosen reference voltage.
Estimated: at a 3 V supply and 1 MSPS throughput, the manufacturer-rated maximum converter power is 4 mW, corresponding to approximately 1.33 mA of supply current. Use these values for a first-pass ADC power budget, then add the reference, input drivers, protection components, and digital interface load. Duty-cycling the acquisition sequence can reduce average power when continuous 1 MSPS sampling is unnecessary.
Use the SPI serial clock rate specified by the Analog Devices manufacturer datasheet and provide adequate settling time between commands and acquisition. Account for conversion time when scheduling successive samples. If the source has high impedance, include an appropriate buffer or charge reservoir near the ADC so the sampling network can settle within the acquisition interval. This is particularly important at the upper end of the 1 MSPS throughput range.
Информация о соответствии
The accessible product information identifies the industrial temperature range and package but does not explicitly state the requested compliance status. Obtain the manufacturer declaration for the exact order code before use in regulated assemblies.