AD9559BCPZ - Dual PLL 1.25GHz Clock Translator | Analog Devices
Артикул: AD9559BCPZ ✓ АктивенAD9559BCPZ Обзор
An adaptive clock translator belongs to the clock and timing IC hierarchy, where it sits above ordinary clock buffers and below complete frequency synthesizers. Its purpose is to recover a low-jitter reference clock from multiple noisy or discontinuous sources and present a stable, phase-aligned output to the line card. This makes the AD9559 suitable for synchronization architectures that must tolerate reference switching while preserving a consistent downstream timing relationship.
The principal features of the AD9559 include two internal PLLs, four external inputs, one output, a low loop bandwidth, and support for synchronization across Ethernet, SONET, and SDH systems. The low loop bandwidth is significant because it filters input jitter rather than passing much of the reference disturbance through to the output. The multiple-input architecture also allows a system to switch among primary and backup clock sources without immediately losing synchronization.
Operationally, the device acts as an adaptive cleanup and translation stage rather than a conventional frequency synthesizer. A recovered reference is routed through the internal PLL and timing paths to produce a clean, synchronized output. The ADI Data Sheet, Rev. D, identifies the part as recommended for new designs and describes it as a dual-PLL, quad-input, multiservice line-card adaptive clock translator. Its 72-lead surface-mount package provides the mixed-signal and high-speed clock connections required in a multilayer PCB design.
Typical uses include Ethernet line cards, SONET/SDH transport systems, multiservice equipment, Stratum clock generation, synchronization networks, and test-and-measurement equipment. The device is particularly useful where a clean reference must be recovered from several inputs or where reference transfer between redundant clock sources must not create excessive output jitter.
PCB implementation requires careful treatment of the clock inputs, PLL reference connections, supply rails, and exposed thermal pad. Route clock inputs as short, controlled-impedance traces, keep the analog supply and reference components close to their associated pins, and provide a low-impedance ground return for the package. Verify differential clock amplitude, input slew rate, output jitter, and loop stability against the system timing budget before releasing the layout.
This page consolidates the device function, package and clocking characteristics, application guidance, comparison parameters, and practical PCB considerations to support clock-tree architecture decisions. It also identifies where the AD9559 fits relative to other ADI clock translators and outlines the engineering checks required before substituting any device in a synchronization design.
Аналоги без доработки для AD9559BCPZ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиAD9559BCPZ Характеристики
| Product Type | Adaptive Clock Translator |
| Architecture | Dual PLL |
| Number of External Inputs | 4 inputs |
| Количество выходов | 1 output |
| Maximum Output Frequency | 1.25 GHz |
| Loop Bandwidth | Low loop bandwidth |
| Supported Network Standards | Ethernet, SONET/SDH |
| Package Type | 72-lead LFCSP-VQ |
| Package Dimensions | 10 mm x 10 mm |
| Тип монтажа | Surface Mount |
| Clock Function | Jitter cleanup and synchronization |
| Input Reference Selection | Up to 4 external input references |
| Output Clock Type | Synchronized single output |
| Data Sheet Revision | Rev. D |
| Lifecycle Recommendation | Recommended for new designs |
Руководство по цоколевке AD9559BCPZ в корпусе 10 mm x 10 mm
Цоколевка для AD9559BCPZ (корпус 10 mm x 10 mm). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для AD9559BCPZ.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
AD9559BCPZ подходит для 6 применениеs: Ethernet Line-Card Clocking, SONET and SDH Synchronization, Multiservice Line-Card Timing, Stratum Clock and Frequency Translation, Redundant Reference Failover, Precision Test and Measurement Timing.
Ethernet Line-Card Clocking
The AD9559BCPZ fits Ethernet line cards that must recover a stable timing reference before it reaches transmit or receive datapaths. Its four external inputs support primary and backup reference selection, while the low-loop-bandwidth PLL path filters jitter and maintains a controlled output relationship. The single 1.25 GHz maximum output is appropriate for a dedicated synchronization stage rather than a general-purpose fanout. During reference transfer, evaluate phase step, output settling time, and downstream tolerance against the Ethernet timing budget before finalizing the clock topology.
Рекомендуется
SONET and SDH Synchronization
The AD9559BCPZ is designed for synchronization systems associated with SONET and SDH transport equipment, where accumulated reference jitter can degrade recovered timing. By cleaning and synchronizing a selected reference, the device provides a controlled clock for downstream timing recovery circuits. Its four-input architecture permits the board to monitor and switch between clock sources. The key qualification step is to reproduce the intended input frequency, loop setting, and output division at the required system jitter level rather than relying only on headline frequency ratings.
Рекомендуется
Multiservice Line-Card Timing
A multiservice line card can place the AD9559BCPZ ahead of multiple timing-consuming circuits to create one clean synchronization source. The four reference inputs support source diversity, and the low-loop-bandwidth architecture reduces reference noise that would otherwise appear at the output. Because the device provides one output, downstream fanout must be implemented with suitable clock drivers whose additive jitter stays within the line-card budget. Validate reference-transfer steps and loss-of-reference recovery with the exact downstream receiver characteristics.
Рекомендуется
Stratum Clock and Frequency Translation
The AD9559BCPZ is appropriate for Stratum-oriented clock and frequency-translation functions that require synchronization among several incoming references. It accepts up to four external sources, uses two PLLs, and delivers one synchronized clock of up to 1.25 GHz. This arrangement allows redundant reference inputs to be combined into a stable downstream timing source without exposing each circuit to independent reference variation. Confirm the supported reference frequencies, output drive level, and loop stability conditions in the AD9559 Data Sheet, Rev. D, for the intended Stratum topology.
Рекомендуется
Redundant Reference Failover
The AD9559BCPZ is well suited to systems that require the output clock to remain controlled while the incoming reference changes. Up to four references can be presented to the device, allowing a primary source and backup sources to share one cleanup path. The low-loop-bandwidth PLL behavior is central to this use because it limits the amount of reference disturbance passed toward the output. Design the selection state machine and loss-of-reference behavior around the device’s documented operating modes, and test reference phase steps at the system level.
Рекомендуется
Precision Test and Measurement Timing
The AD9559BCPZ can provide clean, synchronized timing for test and measurement equipment that must compare traces across multiple acquisition channels. By cleaning an external reference before distribution, it reduces phase disturbance caused by a noisy or switched source. The single-output architecture requires a separate low-jitter fanout stage when several instruments need the same clock. Use the manufacturer’s jitter characterization and loop-bandwidth guidance to establish whether the AD9559’s cleanup capability fits the required measurement uncertainty and phase-noise floor.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AD9559BCPZ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Device Type | Dual-PLL adaptive clock translator |
| Brand | Analog Devices |
| Package | 72-lead LFCSP-VQ, 10 mm x 10 mm |
| External Inputs | 4 inputs |
| Outputs | 1 output |
| Maximum Output Frequency | 1.25 GHz |
| PLL Count | 2 PLLs |
| Primary Function | Jitter cleanup and synchronization |
| Target Applications | Ethernet, SONET/SDH, multiservice line cards, Stratum timing |
| Lifecycle Recommendation | Recommended for new designs |
Ключевые отличия
- Quad-input adaptive clock translation (против AD9554BCPZ)
- Two-PLL jitter-cleanup architecture (против AD9554BCPZ)
- Single synchronized output with 1.25 GHz maximum frequency (против AD9554BCPZ)
- Active recommendation for new designs (против AD9554BCPZ)
Заметки по проектированию
Treat the four clock inputs and the output as controlled-impedance nets, and follow the Analog Devices land pattern for the 72-lead LFCSP-VQ package. Place loop-support components and local decoupling close to their assigned pins, keep the exposed pad tied to a low-impedance ground plane with multiple short vias, and verify return paths beneath every high-speed trace. Do not substitute a generic 72-lead land pattern without checking pad dimensions, thermal-pad geometry, and assembly rules.
Characterize each reference source for frequency, amplitude, slew rate, duty-cycle distortion, and jitter before enabling adaptive selection. Reference transfer can create a phase step at the output, so measure settling time and residual jitter with the intended receiver connected. Differential clock integrity depends on return loss, pair symmetry, and loss through the input network, so validate the complete source-to-pin path rather than relying only on generator output specifications.
Use the supply-current and power-dissipation tables in the AD9559 Data Sheet, Rev. D, for the exact frequency, mode, and temperature grade. Estimate junction rise from package thermal resistance and board copper, then confirm that the regulator can supply transient PLL current without disturbing other timing rails. Provide local decoupling at the supply pins and separate sensitive reference connections from noisy switching nodes to preserve the benefit of jitter cleanup.
Do not assume that another ADI clock translator with a related order code is automatically interchangeable. A valid replacement must match the land pattern, exposed-pad connection, pin functions, reference input range, PLL behavior, output drive, and supply levels. Likewise, do not derive a final jitter budget from the 1.25 GHz headline frequency; include reference noise, loop bandwidth, reference-switch phase steps, board loss, and downstream receiver jitter.
Информация о соответствии
The Analog Devices AD9559 family is identified as recommended for new designs. RoHS, REACH, halogen-free, lead-free, and conflict-minerals status should be confirmed for the exact AD9559BCPZ order code using the manufacturer product page and current material-declaration documentation.