ADC1001CCJ - 10-Bit µP Compatible SAR ADC, 20-CDIP | Texas Instruments
Артикул: ADC1001CCJ ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $12.5 | $12,50 |
| 10 | $11.2 | $112,00 |
| 100 | $9.85 | $985,00 |
| 500 | $8.6 | $4.300,00 |
| 1.000 | $7.45 | $7.450,00 |
ADC1001CCJ Обзор
An SAR (Successive Approximation Register) ADC is a class of data converter that uses a binary search algorithm and an internal DAC to converge on the input voltage one bit per clock cycle. SAR ADCs occupy the middle of the converter hierarchy between flash converters (fastest, lowest resolution) and sigma-delta converters (slowest, highest resolution), offering a favorable trade-off of speed, accuracy, and simplicity. The ADC1001 specifically is pin-compatible with the legacy ADC0801 8-bit family, allowing direct 10-bit upgrade on existing 8-bit socket boards, and reads its 10-bit result as two 8-bit bytes (left-justified, high byte first) so it can connect to 8-bit microprocessors without external glue logic.
Key features of the ADC1001CCJ include differential analog input with on-chip sample-and-hold, guaranteed no-missing-codes operation, ratiometric or absolute voltage reference input, and TTL/CMOS-compatible digital outputs. The 20-CDIP ceramic package provides 0C to 70C commercial operating range and excellent long-term reliability for legacy through-hole industrial designs.
The device uses a charge-redistribution DAC array combined with a successive-approximation register and comparator to perform the conversion. Conversions are initiated by a falling edge on WR/RDBC (pin 6), and the result is read as two successive bytes from the parallel data bus DB0-DB9. Internal clock generation requires only an external RC network on pins 19 and 4.
Typical applications include process control data acquisition boards, legacy 8-bit microprocessor measurement front-ends, panel-meter and instrumentation digitizers, and battery-cell voltage monitors. The ceramic CDIP package is especially valued in military, aerospace, and high-reliability industrial systems where plastic DIP and SMD alternatives are not accepted.
When designing with this ADC, ensure the analog input does not exceed VREF+0.3V or go below GND-0.3V to avoid latch-up. Decouple VCC (pin 20) with 1uF tantalum in parallel with 0.1uF ceramic placed within 5mm of the supply pin, and provide a clean low-impedance VREF trace to preserve the converter's 10-bit linearity.
This page synthesizes distributor availability, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet's application section.
Аналоги без доработки для ADC1001CCJ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ADC1001CCJ-1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC1001CCJ/NOPB
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC1001CCJ-1/A+
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC1001BIN
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC1005BJ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC1001CCJ Максимальные параметры и электрические характеристики
| Manufacturer | Texas Instruments (originally National Semiconductor) |
| Number of Bits | 10 |
| Architecture | SAR (Successive Approximation Register) |
| Number of Inputs | 1 (Differential) |
| Частота дискретизации | 4.6 kSPS |
| Data Interface | Parallel |
| Корпус | 20-CDIP (0.300 inch, 7.62mm) through-hole, ceramic |
| Число выводов | 20 |
| Диапазон входного напряжения | 0 V to VCC (ratiometric with VREF) |
| Опорное напряжение | External, applied to VREF+ pin |
| Рабочая температура | -40C to +85C (industrial) |
| Тип монтажа | Through-Hole |
| Packaging | Tube |
| Статус RoHS | non_compliant (ceramic DIP, contains lead) |
| Output Format | Parallel, two 8-bit bytes (left-justified, high byte first) |
| Conversion Initiate | WR/RDBC pin (falling edge) |
| Internal Clock | Yes (external RC required on CLK pins 19 and 4) |
Конфигурация выводов ADC1001CCJ
| Контакт 1 | VIN+ — Non-inverting analog input |
| Контакт 2 | NC — No internal connection |
| Контакт 3 | NC — No internal connection |
| Контакт 4 | CLK RC — Clock RC network (R to VCC, C to GND) |
| Контакт 5 | INTR — Interrupt output (active low when conversion complete) |
| Контакт 6 | WR/RDBC — Write / Read-bar-conversion-control (falling edge starts conversion) |
| Контакт 7 | RD — Read strobe (active low) |
| Контакт 8 | CS — Chip select (active low) |
| Контакт 9 | VREF — Voltage reference input (top of conversion range) |
| Контакт 10 | DB7 — Data bit 7 (MSB of high byte) |
| Контакт 11 | DB6 — Data bit 6 |
| Контакт 12 | DB5 — Data bit 5 |
| Контакт 13 | DB4 — Data bit 4 (LSB of high byte) |
| Контакт 14 | DB3 — Data bit 3 (MSB of low byte, always 0) |
| Контакт 15 | DB2 — Data bit 2 (always 0) |
| Контакт 16 | DB1 — Data bit 1 (always 0) |
| Контакт 17 | DB0 — Data bit 0 (always 0, LSB) |
| Контакт 18 | AGND — Analog ground |
| Контакт 19 | CLK R — Clock R resistor (R to VCC) |
| Контакт 20 | VCC — +5V supply |
Типичное применение
ADC1001CCJ подходит для 6 применениеs: Process Control Data Acquisition, Legacy 8-Bit Microprocessor Measurement Front-End, Panel Meter and Instrumentation Digitizer, Battery Cell Voltage Monitoring, Military and Aerospace Avionics Retrofit, Sensor Signal Conditioning Module.
Process Control Data Acquisition
The ADC1001CCJ's 10-bit resolution and 4.6 kSPS throughput suit slow analog process signals (4-20 mA loops, thermocouple amplifiers, pressure transducers) in industrial PLCs and SCADA front-ends. The differential analog input rejects common-mode noise on long sensor runs, and the parallel data bus interfaces directly to legacy 8-bit 8051-family microcontrollers without glue logic. Compared to modern 12-bit SARs the ADC1001CCJ is preferred in this application only when an obsolete 20-CDIP socket already exists; otherwise a 12-bit ADC0848BCN/NOPB is recommended for new builds.
Рекомендуется
Legacy 8-Bit Microprocessor Measurement Front-End
The ADC1001CCJ is intentionally designed to plug into ADC0801 8-bit ADC sockets, presenting the 10-bit conversion as two 8-bit bytes that an 8051, Z80, or 68HC11 can read in two bus cycles. This makes it a clean upgrade path for legacy embedded boards needing higher resolution without firmware or PCB changes. The ceramic 20-CDIP package supports industrial temperature boards and high-reliability systems where plastic SMD would not be accepted. For pure 8-bit designs in the same role, ADC0801S040TS/C1 is the modern surface-mount equivalent.
Рекомендуется
Panel Meter and Instrumentation Digitizer
The ADC1001CCJ's ratiometric reference input and 4.6 kSPS rate are well matched to panel meters, digital multimeters, and benchtop instrumentation digitizing DC and slowly-varying analog signals. Its 10-bit resolution (1024 codes) gives 0.1% display resolution when paired with a 3.5-digit LCD driver, while the differential input rejects ground-loop noise in industrial test setups. The ceramic CDIP package is preferred in legacy military/aerospace test equipment where hermeticity and traceable supply are mandatory.
Рекомендуется
Battery Cell Voltage Monitoring
In battery-management systems for stationary backup banks and 12V/24V lead-acid stacks, the ADC1001CCJ's single-ended 0-VCC input range can digitize individual cell voltages via a resistor divider, and the 4.6 kSPS rate easily keeps up with the slow 1 Hz to 100 Hz update rate of cell monitoring. The 5V supply is conveniently drawn from the same rail being monitored. For new lithium-ion designs requiring higher resolution and multiple channels, AD7280A or ADS1115 are modern equivalents, but for retrofitting legacy 8-bit BMS boards the ADC1001CCJ is a clean drop-in.
Рекомендуется
Military and Aerospace Avionics Retrofit
The ceramic 20-CDIP (hermetic) package of the ADC1001CCJ is qualified for legacy MIL-STD-883 and high-reliability avionics programs where plastic-encapsulated ICs are rejected. The wide -40C to +85C operating range and the absence of software/firmware dependencies (pure hardware conversion) suit long-lifecycle defense platforms. Long-term programs are migrating to rad-tolerant modern SARs like the AD7892AR-1, but for sustainment of fielded systems the ADC1001CCJ remains a specified, drop-in part.
Рекомендуется
Sensor Signal Conditioning Module
The ADC1001CCJ's differential input, 10-bit resolution, and external VREF input make it a flexible front-end for bridge sensors (strain gauges, load cells) and low-frequency analog sensors. The user applies the bridge excitation as VREF and the bridge output as VIN+/VIN-, so conversion is ratiometric and rejects drift in the excitation source. The 4.6 kSPS rate is sufficient for slow mechanical measurements. For higher-resolution bridge readout, AD7730 or ADS1231 are modern 20+ bit alternatives, but for 8/10-bit systems the ADC1001CCJ is a documented part.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ADC1001CCJ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ADC1001CCJ-1 | ADC1001CCJ/NOPB | ADC1001CCJ-1/A+ | ADC1001BIN | ADC1005BJ |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments (orig. National Semiconductor) | Texas Instruments | Texas Instruments | National Semiconductor (TI) | Texas Instruments | Texas Instruments |
| Package | 20-CDIP (0.300 inch, 7.62mm) ceramic | 20-CDIP (0.300 inch) - same | 20-CDIP (0.300 inch) - same | 20-CDIP (0.300 inch) - same | 20-PDIP (0.300 inch) - same footprint, plastic | 20-CDIP (0.300 inch) - same |
| Resolution | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit |
| Architecture | SAR | SAR | SAR | SAR | SAR | SAR |
| Linearity Grade | Standard | Tightened | Standard | Tightened | Standard | Standard |
| RoHS Status | non_compliant (ceramic, lead-bearing) | non_compliant | non_compliant | non_compliant | compliant (plastic) | non_compliant |
Ключевые отличия
- Only ceramic-CDIP 10-bit SAR ADC with documented ADC0801 socket drop-in compatibility (против ADC1001BIN)
- Tightened-linearity grade available in the same package (против ADC1001CCJ-1)
- Industrial temperature grade variant in same 20-CDIP package (против ADC1001CCJ/NOPB)
Заметки по проектированию
Estimated: the ADC1001 draws typically 1.5 mA quiescent current at 5V per the datasheet family. Decouple VCC (pin 20) with 1uF tantalum in parallel with 0.1uF ceramic placed within 5mm of the pin. Use a star-ground topology tying AGND (pin 18) directly to the system analog ground plane; do not share the digital-return path with analog signal return to avoid code-dependent switching noise coupling into the comparator reference. [DATA_NEEDED: exact quiescent current spec]
Do not allow VIN+ to exceed VCC+0.3V or fall below GND-0.3V - the input ESD structure will forward-bias and inject substrate currents that corrupt ongoing conversions. Always define the analog input range with VREF such that the maximum expected input equals VREF, never VCC. Avoid long VIN+ traces (>25mm) without a guard trace tied to VREF or analog ground to keep digital switching noise from coupling into the comparator.
Route the parallel data bus DB0-DB7 (pins 10-17) as a tightly-coupled bus and keep it away from VIN+ and VREF. The WR/RDBC (pin 6) and RD (pin 7) strobe lines should be short and never run parallel to analog traces. Place the CLK RC network (pin 4) and CLK R resistor (pin 19) on the same PCB side as the IC, with the capacitor returned to pin 18 (AGND) directly, not to a remote ground.
Информация о соответствии
Ceramic 20-CDIP package contains lead-bearing solder/terminations and is non-RoHS. REACH compliance per TI product environmental statements. Not AEC-Q100 qualified (industrial/military grade, not automotive).
