ADF4217LBRU - Dual RF/IF Integer-N PLL | Analog Devices
Артикул: ADF4217LBRU ✗ Снят с производстваADF4217LBRU Обзор
An integer-N PLL is a frequency synthesizer that uses feedback from a programmable divider to lock an output frequency to a stable reference. The phase-frequency detector compares the divided feedback signal with the reference, while the charge pump drives the loop filter and voltage-controlled oscillator. The resulting architecture provides programmable frequency synthesis with phase and frequency regulation controlled by the external loop-filter components.
The ADF4217 family combines a low-noise digital phase-frequency detector, a precision charge pump, a programmable reference divider, and programmable RF and IF output paths. These functions support dual-channel local-oscillator architectures, allowing one synthesizer to serve both RF and IF sections. The low 3 V nominal operating supply also makes the device suitable for compact, power-conscious RF and communication equipment.
As an integer-N synthesizer, the device divides its internal oscillator frequency by an integer value derived from the programmed RF or IF output path. The programmed output therefore remains locked to the external reference frequency multiplied by the applicable integer division ratio. Designers must select reference, divider, charge-pump-current, and loop-filter values with sufficient phase margin for the intended channel spacing and tuning bandwidth.
Typical uses include wireless receiver and transmitter local oscillators, RF up-converters and down-converters, IF-generation stages, industrial RF links, test and measurement equipment, and communication hardware. The dual RF/IF architecture is especially useful when both sections require coherent signals derived from one reference source.
A key implementation consideration is the loop filter. Its resistance and capacitance set loop bandwidth, damping, reference-spur behavior, and phase margin. Place the loop-filter components close to the relevant device pins, maintain a continuous ground return, and follow the pin-description and reference-layout tables in the Analog Devices ADF4217L data sheet when assigning PCB traces.
This product page combines the manufacturer’s device description with practical selection guidance, application analysis, lifecycle information, and verified source links. It also distinguishes the confirmed TSSOP ordering code from package or temperature variants that require separate qualification before being treated as interchangeable replacements.
Аналоги без доработки для ADF4217LBRU — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиADF4217LBRU Характеристики
| Product Type | Dual RF/IF integer-N PLL frequency synthesizer |
| Nominal Supply Voltage | 3 V |
| Maximum Supply Current | 10 mA |
| Диапазон рабочих температур | -40 °C to +85 °C |
| Temperature Grade | Industrial |
| Number of Terminals | 20 terminals |
| Package Code | TSSOP |
| Package Shape | Rectangular |
| Тип монтажа | Surface mount |
| Architecture | Integer-N PLL |
| Synthesizer Channels | 2 RF/IF channels |
| Phase-Frequency Detector | Low-noise digital phase-frequency detector |
| Charge Pump | Precision charge pump |
| Reference Divider | Programmable |
Руководство по цоколевке ADF4217LBRU в корпусе rectangular
Цоколевка для ADF4217LBRU (корпус rectangular). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для ADF4217LBRU.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
ADF4217LBRU подходит для 6 применениеs: Wireless Receiver RF Local Oscillator, Wireless Transmitter IF Generation, RF Up-Converter and Down-Converter, Industrial RF Communication Link, RF Test and Measurement Equipment, Legacy Communication Hardware Maintenance.
Wireless Receiver RF Local Oscillator
The ADF4217LBRU fits a receiver RF local-oscillator function where a programmable integer-N PLL must translate a stable reference into the mixing frequency required by the selected channel. Its low 3 V nominal supply and maximum 10 mA supply current reduce the power budget in compact RF front ends. The engineer programs the applicable RF divider and reference ratio, then designs the external loop filter around the required channel spacing, phase noise, lock-time behavior, and tuning range. Because the device is obsolete, a receiver built around it is generally a maintenance or lifecycle-extension design rather than a new platform choice. Verify the supported RF output range and register map in the ADF4217L data sheet before releasing the schematic or board layout.
Рекомендуется
Wireless Transmitter IF Generation
The ADF4217LBRU can support IF-generation requirements in a wireless transmitter because its dual RF/IF architecture is intended to provide coherent local-oscillator paths for RF and IF sections. Using one PLL device for related RF and IF functions can simplify frequency coordination and reference distribution, although each output path still requires correct programming and loop-filter design. The 3 V nominal operation is appropriate for compact radio equipment where supply current and board area are constrained. An engineer should establish the required IF frequency, allowed reference ratios, lock-time target, and spur limits before selecting component values. The obsolete lifecycle status makes supply-chain validation and long-term procurement planning essential for transmitter programs that remain in production.
Рекомендуется
RF Up-Converter and Down-Converter
The ADF4217LBRU is applicable to RF and IF conversion architectures because it is explicitly intended to generate local-oscillator signals for up-conversion and down-conversion sections. The programmable divider, low-noise digital phase-frequency detector, and precision charge pump provide the core frequency-generation functions needed by a PLL-based converter. Engineers must calculate each integer division ratio from the reference and desired local-oscillator frequencies, then optimize the loop filter for phase margin and channel spacing. Board placement is also critical because the reference, charge-pump, and sensitive RF paths must not share noisy return-current geometry. For new converter platforms, compare the obsolete ADF4217L with currently supported synthesizers; for existing equipment, its original register compatibility and TSSOP footprint simplify lifecycle-extension work.
Рекомендуется
Industrial RF Communication Link
The ADF4217LBRU can support an industrial RF communications link that requires stable local-oscillator generation from a common reference. Its industrial operating range of -40 °C to +85 °C is suitable for temperature-controlled industrial equipment, and the low-power architecture fits compact transceivers and monitoring systems. The design must account for reference drift, temperature-dependent loop behavior, phase-noise requirements, and the allowed output frequency plan. The external loop filter is the principal tuning element for lock time and damping, so its component tolerances should be included in worst-case analysis. For sustaining an installed link, request lifecycle and supply information through the Request a Quote form and ensure any replacement preserves the 20-terminal TSSOP pinout, register behavior, and electrical characteristics.
Рекомендуется
RF Test and Measurement Equipment
The ADF4217LBRU is appropriate for legacy RF test equipment that needs programmable local-oscillator generation for heterodyne measurements. Its dual RF/IF architecture can support coherent source generation, while integer-N operation provides direct relationship between the reference and programmed output. Instrument designers must evaluate lock-time, phase noise, spurious-signal behavior, and amplitude accuracy because those specifications determine measurement uncertainty and adjacent-channel performance. A stable, low-noise reference and a carefully designed external loop filter are central to achieving repeatable results across temperature and supply conditions. The 3 V nominal operating point and 10 mA maximum supply current support compact instrument architectures. Since the device is obsolete, equipment extensions should preserve the original interface and verify long-term component availability before production release.
Рекомендуется
Legacy Communication Hardware Maintenance
The ADF4217LBRU is well suited to maintaining communication hardware already designed around its 20-terminal TSSOP footprint, register interface, and 3 V supply architecture. Pin-compatible continuity reduces board modification risk during repair, qualification, or end-of-life extension, provided the incoming part has traceable markings and meets the original electrical requirements. The engineer should compare the replacement specification, pin description, register behavior, operating-temperature grade, and package dimensions against the installed design rather than relying only on the family name. Obsolete timing ICs can create counterfeit or mixed-source risks, so procurement should include date-code, visual-inspection, traceability, and electrical-test requirements. Use the Request a Quote form to define those commercial conditions and the associated lifecycle plan for the complete communications assembly.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ADF4217LBRU — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Product Type | Dual RF/IF integer-N PLL frequency synthesizer |
| Brand | Analog Devices |
| Package | 20-terminal TSSOP |
| Nominal Supply Voltage | 3 V |
| Maximum Supply Current | 10 mA |
| Operating Temperature Range | -40 °C to +85 °C |
| Temperature Grade | Industrial |
| Lifecycle Status | Obsolete |
Ключевые отличия
- Purpose-built dual RF and IF synthesis architecture (против ADF4217)
- Industrial temperature operation (против ADF4216)
- Defined 20-terminal TSSOP mechanical format (против ADF4218)
Заметки по проектированию
Place the external loop-filter components close to the charge-pump and related synthesizer pins, following the Analog Devices ADF4217L reference-layout guidance. Keep the sensitive reference and feedback routes compact, avoid routing them beneath noisy digital or switching-supply sections, and provide a continuous ground plane beneath the device. A split or interrupted return path beneath the TSSOP can increase conversion error and degrade phase-noise behavior.
Design the loop filter from the required channel spacing, reference frequency, phase margin, lock time, and spur specifications rather than using a generic resistor-capacitor pair. Evaluate component tolerances and the intended reference phase noise because both can alter damping and reference-spur performance. Confirm the programmed integer ratios against the desired RF and IF output frequencies before finalizing the component values and control firmware.
Decouple the 3 V supply close to the device and provide a quiet return path for the charge pump and digital control signals. Separate or carefully isolate noisy regulator switching paths from the reference and synthesizer areas. Validate startup, lock behavior, and supply-current margin at the system level because the device’s stated maximum supply current is 10 mA and does not include the complete external circuit’s consumption.
Do not treat ADF4216, ADF4217, ADF4218, or different suffix codes as automatic drop-in replacements without checking their exact package drawings, pin assignments, frequency limits, and register definitions. The ADF4217LBRU is an obsolete 20-terminal TSSOP ordering code, so lifecycle continuity and incoming-part traceability are critical. A visual marking check alone is not a substitute for specification review and functional test.
Информация о соответствии
The ADF4217L is documented as an industrial-temperature PLL operating from -40 °C to +85 °C. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 status require confirmation from the manufacturer’s quality documentation before use in regulated production.