Analog Devices

ADM3202ARW - Dual 3.3V RS-232 Transceiver | Analog Devices

Артикул: ADM3202ARW ✓ Активен
3 V to 5.5 V Vdss 16-pin SOIC Package
MOQ: 1 |

ADM3202ARW Обзор

The Analog Devices ADM3202ARW is a dual-channel RS-232 line driver and receiver operating from a single 3.3 V supply in a 16-pin SOIC package. The device supports two transmit channels and two receive channels, conforms to EIA-232E and CCITT V.28 requirements, and operates at data rates up to 230 kbps according to the manufacturer product page. Four external 0.1 µF charge-pump capacitors support the integrated voltage doubler and inverter.

An RS-232 transceiver is an interface IC that converts logic-level signals to RS-232 line levels and converts incoming RS-232 signals back to digital logic. In the signal-chain hierarchy, the ADM3202ARW is a dual RS-232 interface transceiver, placing it within interface ICs, communication semiconductors, and broader industrial and embedded control systems. It is useful where a host, instrument, controller, or service port must communicate with legacy RS-232 equipment over a single 3.3 V power rail.

Key features include two RS-232 drivers and two RS-232 receivers, operation from a single 3.3 V supply, and support for data rates up to 230 kbps. The four external 0.1 µF charge-pump capacitors simplify implementation of the on-chip voltage generation network. The wide SOIC package supports conventional surface-mount assembly, while its dual-channel arrangement reduces the component count compared with using separate single-channel line-driver and receiver devices.

The ADM3202ARW uses charge-pump circuitry to develop the voltage levels required by RS-232 from one low-voltage supply. This architecture suits portable and low-voltage equipment where a 5 V rail is undesirable or unavailable. The EIA-232E and CCITT V.28 conformance provides defined electrical behavior for point-to-point serial links, while the maximum 230 kbps operating rate supports substantially faster communication than commonly required by legacy serial equipment.

Typical uses include industrial serial adapters, test and measurement instruments, point-of-sale terminals, embedded controllers, diagnostic consoles, and portable equipment with RS-232 connectivity. The dual-driver, dual-receiver configuration can support either two independent RS-232 links or a split communication arrangement when the system has limited connector or interface resources. The low 3.3 V operating supply also suits battery-powered and portable industrial designs.

Place the four 0.1 µF charge-pump capacitors close to their designated pins and route the RS-232 driver and receiver traces away from sensitive clock, sensor, and analog inputs. Confirm the system’s supply tolerance, line-driver load, receiver threshold, and grounding strategy against the manufacturer datasheet before layout release. External protection may also be required when the cable can be exposed to electrostatic discharge or surge conditions outside the device's specified operating environment.

Аналоги без доработки для ADM3202ARW — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с ADM3202ARW (тот же форм-фактор и посадочное место) — отличается по Package.

Analog Devices
Package: 16-pin SOIC wide-body
Сравнить с ADM3202ARW →

ADM3202ARWZ

✅ Прямая замена
Analog Devices
📦 16-pin SOIC
Dual RS-232 line driver and receiver · 2 channels · 2 channels · +3.3 V · Up to 230 kbps · EIA-232E and CCITT V.28 · 4 external 0.1 µF capacitors · Full duplex

Уточнить цену

Открыть даташит →

ADM3202ARW Характеристики

Product Type Dual RS-232 line driver and receiver
Number of Transmit Channels 2 channels
Number of Receive Channels 2 channels
Supply Voltage Range 3 V to 5.5 V
Nominal Supply Voltage 3.3 V
Maximum Data Rate 230 kbps
RS-232 Standard EIA-232E
V.28 Standard CCITT V.28
Charge-Pump Capacitor Value 0.1 µF each; 4 capacitors
Interface Direction 2 transmit and 2 receive channels
Корпус 16-pin SOIC
Package Width 7.50 mm
Тип монтажа Surface mount
ESD Protection Rating IEC 1000-4-2

Руководство по цоколевке ADM3202ARW в корпусе 7.50 mm

Цоколевка для ADM3202ARW (корпус 7.50 mm). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.

Схема цоколевки корпуса 7.50 mm для ADM3202ARW

Нет подробных данных о распиновке для ADM3202ARW.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

ADM3202ARW подходит для 6 применениеs: Industrial RS-232 Control Interfaces, Test and Measurement Instruments, Portable Diagnostic Consoles, Point-of-Sale Terminal Interfaces, Embedded Equipment Service Ports, Networked Management and Legacy Bridges.

🏭

Industrial RS-232 Control Interfaces

The ADM3202ARW fits legacy industrial control equipment that exposes RS-232 while accepting a 3.3 V system supply. Its two transmitter and two receiver channels allow one controller to manage multiple serial directions without requiring separate single-channel interface packages. The manufacturer specifies operation up to 230 kbps and conformance to EIA-232E and CCITT V.28, making the device appropriate for configuration ports, service consoles, and legacy machine interfaces. Keep the four 0.1 µF charge-pump capacitors close to the device and route protected RS-232 traces away from sensitive analog sections.

🔧

Test and Measurement Instruments

The ADM3202ARW is suitable for test and measurement equipment that must communicate with older RS-232 instruments through a low-voltage control system. Two receive channels can monitor command acknowledgements and status information, while two driver channels support separate outbound links. Operation from a single 3.3 V supply reduces the need for a dedicated 5 V rail, and the 230 kbps maximum rate accommodates common serial-control traffic. Confirm grounding and logic thresholds in the instrument architecture, and add external surge protection where cables extend beyond the enclosure.

📱

Portable Diagnostic Consoles

A portable diagnostic console can use the ADM3202ARW to bridge a low-voltage controller to RS-232 service equipment. Its single 3.3 V operation aligns with battery-managed embedded systems, while the integrated dual-channel configuration reduces both board area and component count. The 230 kbps capability supports faster configuration and log transfers than many legacy serial ports require. Designers should preserve adequate charge-pump capacitor placement, observe the grounding requirements of connected RS-232 equipment, and provide connector-side protection when the lead is user accessible.

🖥️

Point-of-Sale Terminal Interfaces

The ADM3202ARW can connect a compact point-of-sale controller or peripheral to RS-232 equipment that predates universal USB conversion. Two driver and receiver channels provide flexibility for a command port plus an auxiliary data path. The 3.3 V supply requirement supports integrated embedded platforms, and the 230 kbps rate is suitable for typical peripheral transactions. Place the interface close to the connector entry point, use a controlled ground reference between equipment, and evaluate external protection for retail installations with long or exposed cabling.

🔧

Embedded Equipment Service Ports

The ADM3202ARW is appropriate for embedded equipment that retains an RS-232 service interface for installation, calibration, or field diagnostics. Its 3.3 V operation permits direct use with modern control rails, and the dual-channel arrangement can connect both a service transceiver and a status channel when connector space is limited. The manufacturer identifies EIA-232E and CCITT V.28 conformity as central device characteristics. Validate signal levels with every connected accessory and use a defined common-ground strategy to avoid unreliable behavior in multi-equipment installations.

🌐

Networked Management and Legacy Bridges

The ADM3202ARW can serve as the legacy endpoint of a management or protocol-conversion system, allowing a modern network processor to communicate with RS-232 equipment. Two transmit and two receive channels support bidirectional command and monitoring paths, while the 230 kbps limit should be checked against the protocol timing budget. Single 3.3 V operation simplifies mixed-voltage system design, and the 16-pin SOIC package supports conventional assembly. Route the interface as a controlled transmission-line class, provide chassis grounding where appropriate, and avoid sharing unprotected RS-232 routing with sensitive communications lines.

What is the operating voltage of ADM3202ARW?
The ADM3202ARW operates from a 3 V to 5.5 V supply and is specified for single 3.3 V operation. According to the Analog Devices manufacturer product page, its charge-pump architecture permits operation from one 3.3 V rail without a separate 5 V supply. Designers should use this voltage range to confirm that the host supply remains valid during startup, transients, and cable-driven state changes.
What is the maximum data rate of ADM3202ARW?
The ADM3202ARW supports data rates up to 230 kbps. The Analog Devices manufacturer product page states that the ADM3202, ADM3222, and ADM1385 families conform to EIA-232E and CCITT V.28 and operate up to 230 kbps. This rate comfortably supports legacy serial consoles, configuration ports, and control links while requiring careful signal-integrity and grounding implementation.
How many RS-232 channels does ADM3202ARW provide?
The ADM3202ARW provides two transmit channels and two receive channels in one 16-pin SOIC package. The manufacturer describes it as a high-speed, two-channel RS-232 or V.28 interface device. This integration reduces board area by replacing separate RS-232 driver and receiver packages, particularly where a system needs more than one serial direction.
Where can I download the ADM3202ARW datasheet PDF?
The official ADM3202ARW documentation is available from the Analog Devices ADM3202 product page at https://www.analog.com/en/products/adm3202.html. Use the manufacturer page for the current datasheet, electrical characteristics, pin descriptions, and ordering information. The page also describes the EIA-232E and CCITT V.28 conformance, 3.3 V operation, and external charge-pump capacitor requirements.
Where can I find the ADM3202ARW pinout?
The ADM3202ARW pin assignment is shown in the manufacturer datasheet linked from the Analog Devices ADM3202 product page. The device uses a 16-pin SOIC package with two driver outputs, two receiver inputs, supply and ground pins, and four charge-pump capacitor connections. Use the datasheet pin-description table when assigning PCB nets rather than inferring connections from another RS-232 package.
What capacitors are required for the ADM3202ARW?
The ADM3202ARW requires four external 0.1 µF charge-pump capacitors. According to the Analog Devices manufacturer product page, these capacitors support the voltage doubler and inverter and permit operation from a single 3.3 V supply. Place each capacitor close to the corresponding IC pin and follow the datasheet layout to minimize switching-current loops and preserve stable charge-pump operation.
Can ADM3202ARW interface with a 5 V RS-232 system?
The ADM3202ARW can operate from a 3 V to 5.5 V supply, but its external RS-232 signal levels and operating conditions must be verified against the connected equipment. According to the Analog Devices manufacturer product page, the device is intended for single 3.3 V operation and conforms to EIA-232E and CCITT V.28. Confirm logic thresholds, driver levels, receiver thresholds, and grounding before connecting mixed-voltage systems.
What are the best drop-in replacements for ADM3202ARW?
The closest documented drop-in option is the Analog Devices ADM3202ARWZ, which appears in the 16-SOIC ordering information and retains the same electrical configuration. For a broader substitution, request a manufacturer cross-reference using the ADM3202ARW and 16-pin SOIC requirements. A valid drop-in replacement must preserve the package footprint, pin functions, supply range, channel count, and RS-232 timing characteristics.
What can replace ADM3202ARW without changing the PCB?
ADM3202ARWZ is the closest identified no-layout-change alternative because it is also offered in a 16-SOIC configuration. Its equivalent function depends on the exact ordering code and must be confirmed against the manufacturer datasheet before substitution. Request a formal cross-reference through the Request a Quote form on this page to confirm lead time, lifecycle status, and suffix-specific details.
Is ADM3202ARW suitable for industrial serial communication?
The ADM3202ARW is suitable for industrial RS-232 links when the application requires EIA-232E or CCITT V.28 behavior, a 3.3 V supply, and data rates no higher than 230 kbps. Its dual transmit and receive channels reduce interface-component count. For installations with severe ESD, surge, or cabling exposure, add the appropriate external protection and verify the assembled system against its environmental requirements.
When should I choose ADM3202ARW instead of a single-channel RS-232 transceiver?
Choose ADM3202ARW when the design needs two RS-232 transmit and two receive functions while operating from 3.3 V. A single-channel device can be more appropriate when the board exposes only one serial link or requires a different package arrangement. The ADM3202ARW is preferable for consolidating multiple RS-232 directions into one 16-pin SOIC footprint.
Where can I buy ADM3202ARW and check its lead time?
Use the Request a Quote form on this page to request ADM3202ARW availability, current lead time, and a quotation for the required quantity and packaging. The manufacturer lists ADM3202 directly through its product and sample-buy resources. XAIPART can confirm the exact MPN, current lifecycle status, and order quantity through the quote workflow before procurement.
How much does ADM3202ARW cost?
The current commercial price for ADM3202ARW is obtained through the Request a Quote form on this page. Quote responses reflect the exact MPN, requested quantity, packaging, currency, and current component availability. This avoids publishing a static price that may not match the selected order configuration or the latest market position.
Is ADM3202ARW currently in stock?
Current ADM3202ARW stock should be confirmed through the Request a Quote form on this page. The quote workflow checks the exact ordering code and requested quantity before confirming availability and delivery timing. For production planning, include the required annual usage, lead-time target, and permitted packaging so the procurement response reflects the actual schedule.
What are the key specifications of ADM3202ARW that engineers should know?
The ADM3202ARW is a dual-channel RS-232 transceiver for single 3.3 V operation, with two transmit and two receive channels, a maximum data rate of 230 kbps, and four external 0.1 µF charge-pump capacitors. According to the Analog Devices manufacturer product page, it conforms to EIA-232E and CCITT V.28. The package is a 16-pin SOIC, making pin assignment and layout verification essential.
What is the best cross-brand equivalent for ADM3202ARW?
No cross-brand equivalent is recommended solely from a distributor search result because package and pin-level equivalence must be demonstrated. A valid cross-brand replacement should use the same 16-pin SOIC footprint, provide two transmit and two receive channels, operate across the 3 V to 5.5 V range, and preserve RS-232 timing behavior. Use the Request a Quote form on this page to request a documented cross-reference for this exact requirement.

Справочные инженерные данные для ADM3202ARW — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose ADM3202ARW when the board needs a compact, two-channel RS-232 interface powered from a 3.3 V rail and requires conformance to EIA-232E or CCITT V.28. Its two transmitters, two receivers, and four external 0.1 µF charge-pump capacitors make it well suited to legacy service ports, test instruments, industrial controllers, and compact diagnostic equipment. ADM3202ARWZ is the closest documented same-family alternative in a 16-SOIC package, but the ordering suffix should be checked for marking, temperature, and packing requirements before substitution. A cross-brand choice should be made only after confirming the footprint, pin functions, channel direction, supply range, timing, and lifecycle status. If only one RS-232 direction pair is required, a single-channel transceiver may simplify the PCB; if the design requires 5 V-only legacy compatibility, verify all device and system-level signal requirements before assigning the ADM3202ARW.

Сравнение с аналогами

Параметр Этот товар ADM3202ARWZ
Package 16-pin SOIC 16-pin SOIC
Brand Analog Devices Analog Devices
Transmit Channels 2 channels 2 channels
Receive Channels 2 channels 2 channels

Ключевые отличия

  • Four RS-232 functions in one package (против ADM3202ARWZ)
  • Single-rail 3.3 V interface operation (против ADM3202ARWZ)
  • High-speed legacy-interface capability (против ADM3202ARWZ)

Заметки по проектированию

Place all four 0.1 µF charge-pump capacitors close to their associated ADM3202ARW pins, and minimize the loop area of each capacitor connection. Keep the charge-pump section away from RS-232 receiver traces and sensitive analog inputs. Use the manufacturer datasheet layout as the placement reference, preserving short return paths and avoiding plane splits beneath the charge-pump network.

Separate the RS-232 driver outputs from receiver inputs and low-level signal paths to reduce coupling from stepped-up driver voltages. Route the interface toward the connector without sharing narrow traces with clocks, sensors, or communication lines. Provide a controlled ground reference between connected RS-232 equipment, and evaluate connector-side protection when cables may expose the board to electrostatic discharge or surge transients.

Do not assume that a 16-pin SOIC RS-232 device is pin-compatible with every other 16-SOIC transceiver. Verify the ADM3202ARW pin-description table, supply pins, charge-pump capacitor connections, receiver inputs, and driver outputs against the proposed board. Also confirm the 230 kbps maximum data rate and the EIA-232E or CCITT V.28 requirements of the connected equipment before releasing the design.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The manufacturer documentation identifies ESD protection to IEC 1000-4-2, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements require confirmation from current product documentation. AEC-Q100 status is treated as not applicable because this is an industrial interface IC rather than an automotive-qualified device.

Похожие запросы

ADM3202ARW datasheet ADM3202ARW datasheet pdf ADM3202ARW pinout ADM3202ARW replacement ADM3202ARW equivalent ADM3202ARW cross reference ADM3202ARW price ADM3202ARW stock Analog Devices ADM3202ARW ADM3202ARW 3.3V RS-232 ADM3202ARW 16-SOIC footprint ADM3202ARW vs ADM3202ARWZ ADM3202ARW industrial serial interface how does ADM3202ARW charge pump work

Связанные компоненты & термины

Analog Devices ADM3202 ADM3202ARW ADM3202ARWZ RS-232 transceiver RS-232 line driver RS-232 line receiver interface IC communication semiconductor EIA-232E CCITT V.28 3.3 V power supply 230 kbps charge-pump capacitor 0.1 µF capacitor 16-pin SOIC SOIC package family surface-mount assembly industrial control equipment test and measurement instrumentation portable diagnostic console point-of-sale terminal ESD protection IEC 1000-4-2
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ