ADM3202ARW - Dual 3.3V RS-232 Transceiver | Analog Devices
MPN: ADM3202ARW ✓ AktifADM3202ARW Genel Bakış
An RS-232 transceiver is an interface IC that converts logic-level signals to RS-232 line levels and converts incoming RS-232 signals back to digital logic. In the signal-chain hierarchy, the ADM3202ARW is a dual RS-232 interface transceiver, placing it within interface ICs, communication semiconductors, and broader industrial and embedded control systems. It is useful where a host, instrument, controller, or service port must communicate with legacy RS-232 equipment over a single 3.3 V power rail.
Key features include two RS-232 drivers and two RS-232 receivers, operation from a single 3.3 V supply, and support for data rates up to 230 kbps. The four external 0.1 µF charge-pump capacitors simplify implementation of the on-chip voltage generation network. The wide SOIC package supports conventional surface-mount assembly, while its dual-channel arrangement reduces the component count compared with using separate single-channel line-driver and receiver devices.
The ADM3202ARW uses charge-pump circuitry to develop the voltage levels required by RS-232 from one low-voltage supply. This architecture suits portable and low-voltage equipment where a 5 V rail is undesirable or unavailable. The EIA-232E and CCITT V.28 conformance provides defined electrical behavior for point-to-point serial links, while the maximum 230 kbps operating rate supports substantially faster communication than commonly required by legacy serial equipment.
Typical uses include industrial serial adapters, test and measurement instruments, point-of-sale terminals, embedded controllers, diagnostic consoles, and portable equipment with RS-232 connectivity. The dual-driver, dual-receiver configuration can support either two independent RS-232 links or a split communication arrangement when the system has limited connector or interface resources. The low 3.3 V operating supply also suits battery-powered and portable industrial designs.
Place the four 0.1 µF charge-pump capacitors close to their designated pins and route the RS-232 driver and receiver traces away from sensitive clock, sensor, and analog inputs. Confirm the system’s supply tolerance, line-driver load, receiver threshold, and grounding strategy against the manufacturer datasheet before layout release. External protection may also be required when the cable can be exposed to electrostatic discharge or surge conditions outside the device's specified operating environment.
Drop-in alternatifler için ADM3202ARW — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller ADM3202ARW (aynı form faktörü ve ayağa oturma) — farklı olan Package.
ADM3202ARWZ
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →ADM3202ARW Özellikler
| Product Type | Dual RS-232 line driver and receiver |
| Number of Transmit Channels | 2 channels |
| Number of Receive Channels | 2 channels |
| Supply Voltage Range | 3 V to 5.5 V |
| Nominal Supply Voltage | 3.3 V |
| Maximum Data Rate | 230 kbps |
| RS-232 Standard | EIA-232E |
| V.28 Standard | CCITT V.28 |
| Charge-Pump Capacitor Value | 0.1 µF each; 4 capacitors |
| Interface Direction | 2 transmit and 2 receive channels |
| Paket | 16-pin SOIC |
| Package Width | 7.50 mm |
| Montaj Türü | Surface mount |
| ESD Protection Rating | IEC 1000-4-2 |
ADM3202ARW 7.50 mm Pin Yapısı Kılavuzu
ADM3202ARW (7.50 mm paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: ADM3202ARW.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
ADM3202ARW için uygundur 6 uygulamas: Industrial RS-232 Control Interfaces, Test and Measurement Instruments, Portable Diagnostic Consoles, Point-of-Sale Terminal Interfaces, Embedded Equipment Service Ports, Networked Management and Legacy Bridges.
Industrial RS-232 Control Interfaces
The ADM3202ARW fits legacy industrial control equipment that exposes RS-232 while accepting a 3.3 V system supply. Its two transmitter and two receiver channels allow one controller to manage multiple serial directions without requiring separate single-channel interface packages. The manufacturer specifies operation up to 230 kbps and conformance to EIA-232E and CCITT V.28, making the device appropriate for configuration ports, service consoles, and legacy machine interfaces. Keep the four 0.1 µF charge-pump capacitors close to the device and route protected RS-232 traces away from sensitive analog sections.
Önerilen
Test and Measurement Instruments
The ADM3202ARW is suitable for test and measurement equipment that must communicate with older RS-232 instruments through a low-voltage control system. Two receive channels can monitor command acknowledgements and status information, while two driver channels support separate outbound links. Operation from a single 3.3 V supply reduces the need for a dedicated 5 V rail, and the 230 kbps maximum rate accommodates common serial-control traffic. Confirm grounding and logic thresholds in the instrument architecture, and add external surge protection where cables extend beyond the enclosure.
Önerilen
Portable Diagnostic Consoles
A portable diagnostic console can use the ADM3202ARW to bridge a low-voltage controller to RS-232 service equipment. Its single 3.3 V operation aligns with battery-managed embedded systems, while the integrated dual-channel configuration reduces both board area and component count. The 230 kbps capability supports faster configuration and log transfers than many legacy serial ports require. Designers should preserve adequate charge-pump capacitor placement, observe the grounding requirements of connected RS-232 equipment, and provide connector-side protection when the lead is user accessible.
Önerilen
Point-of-Sale Terminal Interfaces
The ADM3202ARW can connect a compact point-of-sale controller or peripheral to RS-232 equipment that predates universal USB conversion. Two driver and receiver channels provide flexibility for a command port plus an auxiliary data path. The 3.3 V supply requirement supports integrated embedded platforms, and the 230 kbps rate is suitable for typical peripheral transactions. Place the interface close to the connector entry point, use a controlled ground reference between equipment, and evaluate external protection for retail installations with long or exposed cabling.
Önerilen
Embedded Equipment Service Ports
The ADM3202ARW is appropriate for embedded equipment that retains an RS-232 service interface for installation, calibration, or field diagnostics. Its 3.3 V operation permits direct use with modern control rails, and the dual-channel arrangement can connect both a service transceiver and a status channel when connector space is limited. The manufacturer identifies EIA-232E and CCITT V.28 conformity as central device characteristics. Validate signal levels with every connected accessory and use a defined common-ground strategy to avoid unreliable behavior in multi-equipment installations.
Önerilen
Networked Management and Legacy Bridges
The ADM3202ARW can serve as the legacy endpoint of a management or protocol-conversion system, allowing a modern network processor to communicate with RS-232 equipment. Two transmit and two receive channels support bidirectional command and monitoring paths, while the 230 kbps limit should be checked against the protocol timing budget. Single 3.3 V operation simplifies mixed-voltage system design, and the 16-pin SOIC package supports conventional assembly. Route the interface as a controlled transmission-line class, provide chassis grounding where appropriate, and avoid sharing unprotected RS-232 routing with sensitive communications lines.
Önerilen
Mühendislik referans verileri: ADM3202ARW — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | ADM3202ARWZ |
|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC |
| Brand | Analog Devices | Analog Devices |
| Transmit Channels | 2 channels | 2 channels |
| Receive Channels | 2 channels | 2 channels |
Ana Farklılayıcılar
- Four RS-232 functions in one package (karşılaştırma:ADM3202ARWZ)
- Single-rail 3.3 V interface operation (karşılaştırma:ADM3202ARWZ)
- High-speed legacy-interface capability (karşılaştırma:ADM3202ARWZ)
Tasarım Notları
Place all four 0.1 µF charge-pump capacitors close to their associated ADM3202ARW pins, and minimize the loop area of each capacitor connection. Keep the charge-pump section away from RS-232 receiver traces and sensitive analog inputs. Use the manufacturer datasheet layout as the placement reference, preserving short return paths and avoiding plane splits beneath the charge-pump network.
Separate the RS-232 driver outputs from receiver inputs and low-level signal paths to reduce coupling from stepped-up driver voltages. Route the interface toward the connector without sharing narrow traces with clocks, sensors, or communication lines. Provide a controlled ground reference between connected RS-232 equipment, and evaluate connector-side protection when cables may expose the board to electrostatic discharge or surge transients.
Do not assume that a 16-pin SOIC RS-232 device is pin-compatible with every other 16-SOIC transceiver. Verify the ADM3202ARW pin-description table, supply pins, charge-pump capacitor connections, receiver inputs, and driver outputs against the proposed board. Also confirm the 230 kbps maximum data rate and the EIA-232E or CCITT V.28 requirements of the connected equipment before releasing the design.
Uyumluluk Bilgisi
The manufacturer documentation identifies ESD protection to IEC 1000-4-2, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements require confirmation from current product documentation. AEC-Q100 status is treated as not applicable because this is an industrial interface IC rather than an automotive-qualified device.