Analog Devices

ADM487EWARZ - 250kbps 15kV ESD Bus Transceiver | Analog Devices

Артикул: ADM487EWARZ ✓ Активен
5 V Vdss 8-pin SOIC Package
MOQ: 1 |

ADM487EWARZ Обзор

The Analog Devices ADM487EWARZ is a 5 V half-duplex RS-485/RS-422 transceiver operating up to 250 kbps with 15 kV ESD protection in an 8-pin SOIC package. Designed for balanced multipoint data links, the device integrates a transmitter, receiver, driver-control inputs, and bus-deference circuitry for industrial and automotive communication systems.

A half-duplex transceiver is a communication interface that uses the same pair of conductors for transmitting and receiving. Within the interface-IC hierarchy, an RS-485/RS-422 transceiver connects a low-voltage digital controller to a balanced, differential bus. This family supports robust two-wire multipoint networks while using less wiring than separate full-duplex transceivers.

The ADM487EWARZ operates from a 5 V supply, provides a maximum signaling rate of 250 kbps, and is protected against electrostatic discharge to 15 kV. These characteristics make it suitable for industrial control links, building automation equipment, automotive electronics, and other long-wire interfaces where electrostatic discharge and common-mode transients can stress an exposed bus. The automotive AEC-Q100 classification supports its use in appropriately qualified vehicle electronics.

The receiver converts differential bus voltage into a logic-level signal, while the transmitter drives the bus with complementary differential outputs. Separate receiver-enable and driver-enable controls allow the host to select receive or transmit states, supporting half-duplex protocol designs. External termination, biasing, and fail-safe bias networks remain important parts of the complete bus solution.

Typical applications include industrial programmable logic controllers, motor-control equipment, factory sensors, building-automation controllers, automotive body modules, and remote monitoring systems. The 250 kbps rate is appropriate for moderate-speed supervisory and control communication rather than high-bandwidth data transfer.

PCB layout should keep the transceiver close to the connector and preserve a continuous ground reference beneath the bus traces. Place bus-side protection and termination components where transient energy enters the board, and route the differential pair as a tightly coupled pair to minimize radiated noise and improve immunity to external interference.

This page organizes the confirmed electrical characteristics, package details, replacement guidance, comparison parameters, and application-oriented design considerations for engineers evaluating the ADM487EWARZ in RS-485 and RS-422 interfaces.

Аналоги без доработки для ADM487EWARZ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с ADM487EWARZ (тот же форм-фактор и посадочное место) — отличается по Maximum Data Rate.

Analog Devices
Maximum Data Rate: 115 kbps
Сравнить с ADM487EWARZ →

ADM487EARZ

✅ Прямая замена
📦 SOIC-8
Same 5 V supply, 250 kbps rate, and 15 kV ESD rating; 0% difference in those headline ratings, while the exact temperature-grade difference requires datasheet review

📋 Справочный аналог (нет в каталоге)

ADM485EARZ

✅ Прямая замена
📦 SOIC-8
Same 5 V family and 8-pin SOIC footprint with a 250 kbps-class RS-485/RS-422 interface; exact ESD-rating difference versus 15 kV requires datasheet review

📋 Справочный аналог (нет в каталоге)

ADM4850ARZ

✅ Прямая замена
Analog Devices
📦 SOIC-8
Differential line transceiver · EIA RS-485 and RS-422 · 5 V · 115 kbps · Half-duplex · Balanced differential · Multipoint bus · Limited

Уточнить цену

Открыть даташит →

ADM1487EARZ

✅ Прямая замена
📦 SOIC-8
Same 5 V family and SOIC-8 bus-interface format; exact speed and ESD differences from 250 kbps and 15 kV require datasheet verification

📋 Справочный аналог (нет в каталоге)

SP483EEN-L

✅ Прямая замена
📦 SOIC-8
Same 250 kbps half-duplex RS-485/RS-422 class in an 8-pin SOIC package; exact ESD and temperature differences versus 15 kV require datasheet review

📋 Справочный аналог (нет в каталоге)

ADM487EWARZ Характеристики

Напряжение питания 5 V
Maximum Data Rate 250 kbps
ESD Protection 15 kV
Communication Standard RS-485 and RS-422
Duplex Mode Half-duplex
Transmitter and Receiver Count 1 transmitter and 1 receiver
Bus Configuration Balanced differential transmission
Application Profile Multipoint bus transmission lines
Automotive Qualification AEC-Q100
Package Type 8-pin SOIC
Тип монтажа Surface mount
Lead Count 8 leads
Package Family SOIC narrow-body family
TIA/EIA Compliance TIA/EIA compliant
Power Consumption Classification Low power

Конфигурация выводов ADM487EWARZ

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Контакт 1 RO — Receiver output
Контакт 2 /RE — Receiver enable, active low
Контакт 3 DE — Driver enable
Контакт 4 DI — Driver input
Контакт 5 GND — Ground
Контакт 6 A — Noninverting driver output and receiver input
Контакт 7 B — Inverting driver output and receiver input
Контакт 8 VCC — Positive supply voltage

Типичное применение

ADM487EWARZ подходит для 6 применениеs: Industrial PLC Communication, Building Automation, Automotive Body Control Module, Factory Sensor Network, Motor and Equipment Control, Remote Monitoring Equipment.

🏭

Industrial PLC Communication

The ADM487EWARZ fits industrial programmable logic controller links that use 5 V RS-485 or RS-422 signaling at rates up to 250 kbps. Its half-duplex architecture lets a controller share one differential bus pair for command transmission and sensor-response reception, reducing wiring compared with separate transmit and receive paths. The 15 kV ESD rating adds protection for a board-mounted interface exposed to electrostatic discharge during installation and maintenance. Designers should still place the transceiver near the connector, provide a continuous ground reference, and implement the termination and fail-safe bias network required by the bus topology.

🧩

Building Automation

The ADM487EWARZ is appropriate for building-automation controllers communicating with distributed sensors, actuators, and lighting-control modules over a balanced bus. Its 250 kbps maximum rate is appropriate for supervisory commands and status exchange, while the 5 V supply simplifies integration with conventional embedded control electronics. Half-duplex operation supports shared multipoint cabling and can reduce connector and wiring complexity. Field reliability depends on correct bus biasing at a designated location, termination at the physical ends of the cable, and protection close to the external connector so surge or electrostatic-discharge events do not propagate directly into the controller board.

🚗

Automotive Body Control Module

The ADM487EWARZ supports qualified automotive body and submodule communication designs that use a 5 V half-duplex RS-485 or RS-422 bus. The AEC-Q100 classification, 250 kbps data rate, and 15 kV ESD protection align with control networks handling configuration commands and diagnostic status rather than high-bandwidth payload traffic. A robust implementation should route the balanced pair away from switching nodes, maintain a low-impedance ground plane beneath the bus, and place the ESD protection path close to the connector. Final automotive use requires compliance with the manufacturer’s qualification, traceability, and quality-system requirements.

🏭

Factory Sensor Network

The ADM487EWARZ can connect a controller to a field bus of industrial sensors over a twisted-pair network operating up to 250 kbps. Half-duplex communication is effective when many nodes share the same conductors and traffic consists of periodic measurements and configuration commands. The transceiver’s 15 kV ESD protection is useful at equipment edges where personnel contact or industrial transients may reach the interface. Reliable network behavior also depends on selecting one fail-safe bias location, avoiding excessive stub lengths, terminating only the physical ends of the bus, and verifying that cable length, data rate, topology, and termination remain within the chosen system’s specifications.

⚡

Motor and Equipment Control

The ADM487EWARZ supports moderate-speed command and status links in motor controllers, remote equipment, and actuator-control modules. At 250 kbps, it accommodates supervisory protocols without requiring the speed of a high-performance differential interface. The half-duplex arrangement allows a controller to transmit operating commands and receive position, fault, or health information over the same balanced pair, simplifying the external connector. The design should isolate the transceiver from motor-switching energy through careful grounding and layout, and it should include protection at the cable entry to prevent industrial transients from reaching sensitive controller electronics.

🌐

Remote Monitoring Equipment

The ADM487EWARZ fits remote monitoring units that exchange commands and telemetry over an RS-485 or RS-422 network at rates up to 250 kbps. Its one-transmitter, one-receiver half-duplex arrangement is effective for two-wire installations in which each endpoint alternates between requesting data and returning measurements. The 5 V interface supports integration with embedded control logic, and the documented 15 kV ESD rating helps protect a port exposed to installation or maintenance events. Systems should include a defined bus-idle state, controlled transmitter enable timing, a single-point bias strategy, and surge protection near the connector for dependable operation over field cabling.

Сводка рекомендуемых товаров

ADM485E Related low-power RS-485/RS-422 transceiver family Используется в: Industrial PLC Communication, Building Automation, Factory Sensor Network, Motor and Equipment Control, Remote Monitoring Equipment ADM487E Closest ADM487E family function Используется в: Industrial PLC Communication, Building Automation, Automotive Body Control Module, Factory Sensor Network, Remote Monitoring Equipment ADM1487E Related balanced data-transceiver family Используется в: Automotive Body Control Module, Motor and Equipment Control
What is the ADM487EWARZ?
The ADM487EWARZ is a 5 V, half-duplex RS-485/RS-422 transceiver with one transmitter, one receiver, a maximum data rate of 250 kbps, and 15 kV ESD protection. According to the Analog Devices ADM485E, ADM487E, and ADM1487E family datasheet, it is intended for balanced data transmission over multipoint bus lines and is packaged in an 8-pin SOIC.
What is the operating voltage of ADM487EWARZ?
The ADM487EWARZ operates from a 5 V supply. The manufacturer product page and family datasheet identify the ADM487E as a 5 V low-power data transceiver. Because the device is designed around a 5 V rail, its supply-decoupling network and interface logic should be evaluated against the exact electrical limits stated in the manufacturer datasheet before a board is released.
How fast can ADM487EWARZ transmit data?
The ADM487EWARZ supports a maximum data rate of 250 kbps. The Mouser technical listing identifies it as a 5 V, 15 kV ESD-protected, half-duplex RS-485/RS-422 transceiver rated for 250 kbps. This rate suits supervisory, control, and sensor-network links where moderate throughput is more important than high-speed data transfer.
Is ADM487EWARZ suitable for automotive applications?
Yes, the ADM487EWARZ is identified as an automotive AEC-Q100 device in the available part classification. Its 5 V operation, 250 kbps data rate, and 15 kV ESD protection suit qualified automotive control links. Automotive qualification does not remove the need to follow the manufacturer’s AEC-Q100 application, ESD, and quality requirements in the final design.
Where can I download the ADM487EWARZ datasheet PDF?
The ADM487EWARZ datasheet is available through the official Analog Devices family document titled ADM485E, ADM487E, and ADM1487E. The manufacturer PDF is the authoritative source for pin descriptions, electrical limits, timing, ESD ratings, and package dimensions. Use that document for the complete pinout and application information rather than relying on a distributor summary.
Where can I find the ADM487EWARZ pinout?
The ADM487EWARZ pinout is shown in the Analog Devices ADM485E, ADM487E, and ADM1487E family datasheet. The 8-pin SOIC interface uses the conventional differential bus and control functions: DI, RO, DE, /RE, driver outputs, receiver inputs, supply, and ground. Consult the datasheet pin-description table and package drawing for authoritative numbering.
ADM487EWARZ vs ADM4850ARZ: which is the better bus transceiver?
The ADM487EWARZ is the stronger choice when 15 kV ESD protection is required because the manufacturer identifies that rating explicitly. The ADM4850ARZ comparison record confirms a related ADM4850-family part, but the exact protection, speed, and temperature limits must be checked in its datasheet. Both use an 8-pin SOIC format, making footprint compatibility an important but not sufficient replacement criterion.
What is the best drop-in replacement for ADM487EWARZ?
The ADM487EARZ is the closest same-family option because it retains the ADM487E function and 8-pin SOIC package while representing the non-automotive ordering code. The ADM487EWARZ-REEL7 provides the same electrical device in reel packaging, but it is not a distinct functional replacement. Confirm temperature grade, pin configuration, and qualification requirements in the manufacturer datasheet before substitution.
Can SP483EEN-L replace ADM487EWARZ?
SP483EEN-L is a candidate drop-in replacement when its pinout, supply limits, and operating ratings match the ADM487EWARZ design. The cross-reference information describes it as a 250 kbps half-duplex RS-485/RS-422 transceiver with enhanced ESD performance in an 8-pin SOIC package. Verify enable polarity, fail-safe behavior, and temperature range against the two manufacturer datasheets before production use.
When should I choose ADM487EWARZ over SP483EEN-L?
Choose ADM487EWARZ when the design specifically calls for the documented 15 kV ESD rating and automotive AEC-Q100 classification. SP483EEN-L may be appropriate when its own datasheet confirms equivalent pin behavior, supply range, ESD rating, and environmental qualifications for the target application. The deciding factor should be verified ratings and qualification, not package appearance alone.
Is ADM487EWARZ suitable for industrial multipoint networks?
Yes, the ADM487EWARZ is suitable for 5 V industrial multipoint communication links operating up to 250 kbps. The manufacturer describes the family for balanced data transmission and multipoint bus lines. Industrial deployments should still include correct termination, fail-safe biasing, surge protection, ground-plane continuity, and cable-level fault analysis.
Where can I buy ADM487EWARZ online?
Use the Request a Quote form on this page to request ADM487EWARZ availability, current commercial terms, and lead time. The form provides a direct purchasing path without relying on static price information. Package form, production volume, and automotive qualification requirements should be stated with the request so the correct ADM487EWARZ ordering option is reviewed.
What is the price of ADM487EWARZ?
Current commercial pricing for the ADM487EWARZ is obtained through the Request a Quote form on this page. Request the quantity, tube or reel packaging preference, and required delivery schedule for a responsive quotation. Pricing can change with volume, availability, and logistics, so a current quotation is more useful than a static historical price.
What is the lead time for ADM487EWARZ?
The current ADM487EWARZ lead time depends on order quantity, package format, and manufacturing availability. Use the Request a Quote form on this page and specify your required quantity, target date, and whether the order must be AEC-Q100 qualified. The manufacturer product page is the appropriate reference for confirming the device’s present product status.
Is ADM487EWARZ in stock?
Current stock for ADM487EWARZ should be confirmed through the Request a Quote form on this page. State the required quantity, package format, and production schedule when requesting availability. This avoids treating a distributor search result as a guaranteed stock commitment and supports an allocation decision based on your actual build plan.
What can replace ADM487EWARZ?
ADM487EARZ, ADM485EARZ, ADM4850ARZ, and ADM1487EARZ are same-manufacturer candidates to evaluate against the ADM487EWARZ, while SP483EEN-L is a cross-brand candidate identified in the 250 kbps half-duplex comparison. A valid replacement must match the 8-pin SOIC land pattern, pin functions, enable logic, supply range, ESD rating, and environmental qualification; use the manufacturer datasheets for final approval.
What are the key specifications of ADM487EWARZ that engineers should know?
The key ADM487EWARZ specifications are a 5 V supply, half-duplex RS-485/RS-422 operation, 250 kbps maximum data rate, 15 kV ESD protection, one transmitter and one receiver, and an 8-pin SOIC package. The part is also identified as AEC-Q100 automotive qualified. The Analog Devices family datasheet remains the controlling source for timing, electrical limits, pinout, and test conditions.

Справочные инженерные данные для ADM487EWARZ — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose ADM487EWARZ when the design requires a 5 V, half-duplex RS-485/RS-422 transceiver at up to 250 kbps, 15 kV ESD protection, and an AEC-Q100-qualified option in an 8-pin SOIC package. ADM487EARZ is the logical same-family candidate when the exact device function and footprint are needed but the automotive ordering code is not required. ADM485EARZ and ADM4850ARZ may fit conventional industrial interfaces, but their speed, protection, and temperature limits must be matched against the target requirements. ADM1487EARZ is another member of the related balanced-transceiver family and should be selected around its specific interface behavior. SP483EEN-L offers a cross-brand, 250 kbps half-duplex alternative with enhanced ESD performance, making it relevant when its datasheet confirms the required pinout, supply, fail-safe, and environmental ratings. Package equivalence alone is insufficient: verify enable polarity, receiver output behavior, bus-idle handling, and qualification before approving any substitution.

Сравнение с аналогами

Параметр Этот товар ADM487EARZ ADM485EARZ ADM4850ARZ ADM1487EARZ SP483EEN-L
Package SOIC-8 SOIC-8 SOIC-8 SOIC-8 SOIC-8 SOIC-8
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Diodes Incorporated
Communication Standard RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422

Ключевые отличия

  • Higher documented ESD protection than the generic comparison baseline (против ADM485EARZ)
  • Automotive qualification in the same 8-pin SOIC format (против ADM487EARZ)
  • Confirms the same 250 kbps half-duplex class in a cross-brand candidate (против SP483EEN-L)

Заметки по проектированию

Route the A and B conductors as a tightly coupled differential pair with continuous, uninterrupted ground reference beneath the traces. Keep the transceiver and protection network near the connector so external transient energy is diverted before reaching the IC. Avoid routing the bus through digital switching areas, and use a solid ground plane rather than fragmented return paths that can increase radiated noise and susceptibility.

Termination and fail-safe bias are system-level requirements, not optional decoration. Place termination only at the physical ends of the bus, and provide a defined idle state so an undriven or disconnected line does not produce unwanted receiver transitions. In a multipoint network, avoid excessive cable stubs because their reflections can degrade the 250 kbps signaling margin.

Control DE and /RE so the transmitter is enabled only when the bus is not receiving, with suitable dead time between directions. The maximum supported rate is 250 kbps, but reliable operation also depends on cable loss, topology, termination, common-mode limits, and protection-device capacitance. Validate the assembled board with representative cable lengths and the worst-case transceiver enable timing used by the bus protocol.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The part is identified as automotive AEC-Q100 qualified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the confirmed product data.

Данные проверены: 2026-11-19 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

ADM487EWARZ datasheet ADM487EWARZ pinout ADM487EWARZ datasheet pdf ADM487EWARZ equivalent ADM487EWARZ replacement ADM487EWARZ cross reference ADM487EWARZ vs SP483EEN-L ADM487EWARZ SOIC-8 footprint ADM487EWARZ 250kbps RS-485 ADM487EWARZ 15kV ESD Analog Devices ADM487EWARZ ADM487EWARZ automotive transceiver ADM487EWARZ price ADM487EWARZ stock

Связанные компоненты & термины

Analog Devices ADM487EWARZ ADM487E ADM485E ADM1487E SP483EEN-L RS-485 RS-422 TIA/EIA standard half-duplex transceiver differential data transceiver interface IC balanced transmission line multipoint bus ESD protection 15 kV ESD 250 kbps 5 V supply AEC-Q100 automotive electronics SOIC-8 SOIC narrow-body family surface-mount package industrial control building automation
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ