ADM487EWARZ - 250kbps 15kV ESD Bus Transceiver | Analog Devices
MPN: ADM487EWARZ ✓ Hoạt độngADM487EWARZ Tóm tắt
A half-duplex transceiver is a communication interface that uses the same pair of conductors for transmitting and receiving. Within the interface-IC hierarchy, an RS-485/RS-422 transceiver connects a low-voltage digital controller to a balanced, differential bus. This family supports robust two-wire multipoint networks while using less wiring than separate full-duplex transceivers.
The ADM487EWARZ operates from a 5 V supply, provides a maximum signaling rate of 250 kbps, and is protected against electrostatic discharge to 15 kV. These characteristics make it suitable for industrial control links, building automation equipment, automotive electronics, and other long-wire interfaces where electrostatic discharge and common-mode transients can stress an exposed bus. The automotive AEC-Q100 classification supports its use in appropriately qualified vehicle electronics.
The receiver converts differential bus voltage into a logic-level signal, while the transmitter drives the bus with complementary differential outputs. Separate receiver-enable and driver-enable controls allow the host to select receive or transmit states, supporting half-duplex protocol designs. External termination, biasing, and fail-safe bias networks remain important parts of the complete bus solution.
Typical applications include industrial programmable logic controllers, motor-control equipment, factory sensors, building-automation controllers, automotive body modules, and remote monitoring systems. The 250 kbps rate is appropriate for moderate-speed supervisory and control communication rather than high-bandwidth data transfer.
PCB layout should keep the transceiver close to the connector and preserve a continuous ground reference beneath the bus traces. Place bus-side protection and termination components where transient energy enters the board, and route the differential pair as a tightly coupled pair to minimize radiated noise and improve immunity to external interference.
This page organizes the confirmed electrical characteristics, package details, replacement guidance, comparison parameters, and application-oriented design considerations for engineers evaluating the ADM487EWARZ in RS-485 and RS-422 interfaces.
Bộ thay thế dễ dàng lắp đặt cho ADM487EWARZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADM487EWARZ (cùng hình factor và footprint) — khác nhau ở Maximum Data Rate.
ADM487EARZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM485EARZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM4850ARZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADM1487EARZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SP483EEN-L
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM487EWARZ Thông số kỹ thuật
| Điện áp cung cấp | 5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | 15 kV |
| Communication Standard | RS-485 and RS-422 |
| Duplex Mode | Half-duplex |
| Transmitter and Receiver Count | 1 transmitter and 1 receiver |
| Bus Configuration | Balanced differential transmission |
| Application Profile | Multipoint bus transmission lines |
| Automotive Qualification | AEC-Q100 |
| Package Type | 8-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Lead Count | 8 leads |
| Package Family | SOIC narrow-body family |
| TIA/EIA Compliance | TIA/EIA compliant |
| Power Consumption Classification | Low power |
Cấu hình chân ADM487EWARZ
| Chân 1 | RO — Receiver output |
| Chân 2 | /RE — Receiver enable, active low |
| Chân 3 | DE — Driver enable |
| Chân 4 | DI — Driver input |
| Chân 5 | GND — Ground |
| Chân 6 | A — Noninverting driver output and receiver input |
| Chân 7 | B — Inverting driver output and receiver input |
| Chân 8 | VCC — Positive supply voltage |
Ứng dụng tiêu biểu
ADM487EWARZ phù hợp cho 6 Áp dụngs: Industrial PLC Communication, Building Automation, Automotive Body Control Module, Factory Sensor Network, Motor and Equipment Control, Remote Monitoring Equipment.
Industrial PLC Communication
The ADM487EWARZ fits industrial programmable logic controller links that use 5 V RS-485 or RS-422 signaling at rates up to 250 kbps. Its half-duplex architecture lets a controller share one differential bus pair for command transmission and sensor-response reception, reducing wiring compared with separate transmit and receive paths. The 15 kV ESD rating adds protection for a board-mounted interface exposed to electrostatic discharge during installation and maintenance. Designers should still place the transceiver near the connector, provide a continuous ground reference, and implement the termination and fail-safe bias network required by the bus topology.
Được đề xuất
Building Automation
The ADM487EWARZ is appropriate for building-automation controllers communicating with distributed sensors, actuators, and lighting-control modules over a balanced bus. Its 250 kbps maximum rate is appropriate for supervisory commands and status exchange, while the 5 V supply simplifies integration with conventional embedded control electronics. Half-duplex operation supports shared multipoint cabling and can reduce connector and wiring complexity. Field reliability depends on correct bus biasing at a designated location, termination at the physical ends of the cable, and protection close to the external connector so surge or electrostatic-discharge events do not propagate directly into the controller board.
Được đề xuất
Automotive Body Control Module
The ADM487EWARZ supports qualified automotive body and submodule communication designs that use a 5 V half-duplex RS-485 or RS-422 bus. The AEC-Q100 classification, 250 kbps data rate, and 15 kV ESD protection align with control networks handling configuration commands and diagnostic status rather than high-bandwidth payload traffic. A robust implementation should route the balanced pair away from switching nodes, maintain a low-impedance ground plane beneath the bus, and place the ESD protection path close to the connector. Final automotive use requires compliance with the manufacturer’s qualification, traceability, and quality-system requirements.
Được đề xuất
Factory Sensor Network
The ADM487EWARZ can connect a controller to a field bus of industrial sensors over a twisted-pair network operating up to 250 kbps. Half-duplex communication is effective when many nodes share the same conductors and traffic consists of periodic measurements and configuration commands. The transceiver’s 15 kV ESD protection is useful at equipment edges where personnel contact or industrial transients may reach the interface. Reliable network behavior also depends on selecting one fail-safe bias location, avoiding excessive stub lengths, terminating only the physical ends of the bus, and verifying that cable length, data rate, topology, and termination remain within the chosen system’s specifications.
Được đề xuất
Motor and Equipment Control
The ADM487EWARZ supports moderate-speed command and status links in motor controllers, remote equipment, and actuator-control modules. At 250 kbps, it accommodates supervisory protocols without requiring the speed of a high-performance differential interface. The half-duplex arrangement allows a controller to transmit operating commands and receive position, fault, or health information over the same balanced pair, simplifying the external connector. The design should isolate the transceiver from motor-switching energy through careful grounding and layout, and it should include protection at the cable entry to prevent industrial transients from reaching sensitive controller electronics.
Được đề xuất
Remote Monitoring Equipment
The ADM487EWARZ fits remote monitoring units that exchange commands and telemetry over an RS-485 or RS-422 network at rates up to 250 kbps. Its one-transmitter, one-receiver half-duplex arrangement is effective for two-wire installations in which each endpoint alternates between requesting data and returning measurements. The 5 V interface supports integration with embedded control logic, and the documented 15 kV ESD rating helps protect a port exposed to installation or maintenance events. Systems should include a defined bus-idle state, controlled transmitter enable timing, a single-point bias strategy, and surge protection near the connector for dependable operation over field cabling.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADM487EWARZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADM487EARZ | ADM485EARZ | ADM4850ARZ | ADM1487EARZ | SP483EEN-L |
|---|---|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Diodes Incorporated |
| Communication Standard | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
Bảo phân biệt quan trọng
- Higher documented ESD protection than the generic comparison baseline (vsADM485EARZ)
- Automotive qualification in the same 8-pin SOIC format (vsADM487EARZ)
- Confirms the same 250 kbps half-duplex class in a cross-brand candidate (vsSP483EEN-L)
Ghi chú thiết kế
Route the A and B conductors as a tightly coupled differential pair with continuous, uninterrupted ground reference beneath the traces. Keep the transceiver and protection network near the connector so external transient energy is diverted before reaching the IC. Avoid routing the bus through digital switching areas, and use a solid ground plane rather than fragmented return paths that can increase radiated noise and susceptibility.
Termination and fail-safe bias are system-level requirements, not optional decoration. Place termination only at the physical ends of the bus, and provide a defined idle state so an undriven or disconnected line does not produce unwanted receiver transitions. In a multipoint network, avoid excessive cable stubs because their reflections can degrade the 250 kbps signaling margin.
Control DE and /RE so the transmitter is enabled only when the bus is not receiving, with suitable dead time between directions. The maximum supported rate is 250 kbps, but reliable operation also depends on cable loss, topology, termination, common-mode limits, and protection-device capacitance. Validate the assembled board with representative cable lengths and the worst-case transceiver enable timing used by the bus protocol.
Thông tin tuân thủ
The part is identified as automotive AEC-Q100 qualified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the confirmed product data.