ADS1100A3IDBVRG4 - 16-Bit Self-Calibrating I2C ADC | Texas Instruments
Артикул: ADS1100A3IDBVRG4 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.2 | $4,20 |
| 10 | $3.78 | $37,80 |
| 100 | $3.35 | $335,00 |
| 500 | $2.95 | $1.475,00 |
| 1.000 | $2.55 | $2.550,00 |
ADS1100A3IDBVRG4 Обзор
A delta-sigma (sigma-delta) ADC is a type of oversampling converter that uses a modulator loop and a digital decimation filter to achieve high resolution at low bandwidth. Within the broader converter taxonomy it belongs to the precision-ADC family, sitting between successive-approximation register (SAR) ADCs (faster, lower-resolution) and integrating ADCs (slowest, highest noise-rejection). The ADS1100 integrates the modulator, digital filter, PGA, and I2C interface into a single chip, making it a complete data-acquisition system in a tiny SOT-23-6 footprint suitable for board-constrained designs.
Key features include a maximum integral nonlinearity (INL) of 0.0125% of full-scale range, no missing codes at 16 bits, continuous self-calibration, single-cycle conversion, PGA gains of 1, 2, 4, or 8, and low noise of 4 uVp-p. The continuous self-calibration scheme removes offset and gain drift in real time, eliminating the periodic user calibration required by many competing converters and simplifying long-running sensor measurements.
Typical applications include portable instrumentation, weigh scales, industrial process control, factory-automation analog front-ends, battery monitors, and consumer sensor read-out boards where a small footprint, low power consumption, and I2C connectivity outweigh the need for higher sample rates or true differential bipolar inputs. The ratiometric conversion principle makes the ADS1100 especially attractive for bridge sensor measurements powered by the same rail as the ADC.
A key design consideration is the supply used as the reference: any noise or drift on VDD appears directly in the conversion, so a clean, low-impedance supply with adequate decoupling is essential. The ADS1100A3IDBVRG4 is supplied on a 3000-piece tape-and-reel and is qualified for the -40 C to +85 C industrial temperature range.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single source for selection, sourcing, and PCB implementation guidance.
Аналоги без доработки для ADS1100A3IDBVRG4 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ADS1100A3IDBVRG4 (тот же форм-фактор и посадочное место) — отличается по Architecture, Reference, Resolution.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ADS1100A0IDBVRG4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADS1100A4IDBVRG4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADS1100A5IDBVRG4
✅ Прямая замена✓ В наличии
$2.4 / шт.
Открыть даташит →ADS1100A1IDBVRG4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADS1110A1IDBVR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCP3421A0T-E/CH
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADS1100A3IDBVRG4 Максимальные параметры и электрические характеристики
| Разрешение | 16 bits |
| Number of Input Channels | 1 differential |
| Architecture | Delta-Sigma (Sigma-Delta) |
| Data Rate (programmable) | 8 / 16 / 32 / 128 SPS |
| Напряжение питания | 2.7 V to 5.5 V |
| Integral Nonlinearity (INL) max | 0.0125 % of FSR |
| No Missing Codes | 16 bits guaranteed |
| Программируемый усилитель (PGA) | 1, 2, 4, 8 |
| Input-Referred Noise | 4 uVp-p |
| Reference | VDD (ratiometric, internal) |
| Digital Interface | I2C-compatible, standard / fast mode |
| I2C Slave Address (A3 variant) | 0x48 (ADDR=GND) / 0x4A (ADDR=VDD) |
| Рабочая температура | -40 C to +85 C |
| Корпус | SOT-23-6 (DBV) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
| Conversion Mode | Single-cycle, continuous, self-calibrating |
Конфигурация выводов ADS1100A3IDBVRG4
| Контакт 1 | ADDR — I2C address select (GND or VDD selects between two device addresses) |
| Контакт 2 | VDD — Power supply input (2.7 V to 5.5 V); also used as ratiometric ADC reference |
| Контакт 3 | GND — Ground return for supply and signal |
| Контакт 4 | SDA — I2C serial data (open-drain, requires pull-up to VDD) |
| Контакт 5 | SCL — I2C serial clock input |
| Контакт 6 | VIN+/VIN- — Differential analog input (positive and negative tied together at the pin) |
Типичное применение
ADS1100A3IDBVRG4 подходит для 6 применениеs: Portable Weigh Scales and Load Cells, Industrial Process Control Analog Front-Ends, Battery Monitoring and Portable Instrumentation, Consumer Sensor Read-Out Boards, Factory Automation Sensor Interfaces, Medical and Wellness Monitoring Devices.
Portable Weigh Scales and Load Cells
The ADS1100A3IDBVRG4 fits weigh-scale designs because its PGA gains of 1/2/4/8 directly amplify low-level bridge outputs while the 16-bit no-missing-code resolution captures weight granularity required for commercial scales. The ratiometric conversion uses VDD as the reference, so the bridge excitation supply and ADC reference are the same node, eliminating reference-mismatch error. According to the TI ADS1100 datasheet, the continuous self-calibration loop removes offset and gain drift every conversion, eliminating the periodic user calibration demanded by competing ADCs. With 128 SPS maximum data rate and SOT-23-6 footprint, the part supports handheld scales where PCB area is at a premium and battery life depends on low active current.
Рекомендуется
Industrial Process Control Analog Front-Ends
The ADS1100A3IDBVRG4 is well suited to industrial 4-20 mA loop digitization and process-variable monitoring because the differential input rejects common-mode noise from long sensor cables. The integrated PGA simplifies signal conditioning for thermocouple and RTD bridge circuits, while the I2C interface lets multiple ADS1100s share a single controller bus for multi-channel monitoring. With -40 C to +85 C industrial temperature range and self-calibration, the part maintains accuracy in unattended factory environments. Per the TI datasheet, the 2.7 V to 5.5 V supply range accommodates both 3.3 V and 5 V industrial rails without level shifters.
Рекомендуется
Battery Monitoring and Portable Instrumentation
The ADS1100A3IDBVRG4 is ideal for battery-powered handheld instruments because its low supply current and 2.7 V minimum operation extend runtime on single-cell Li-ion packs. The ratiometric measurement makes it straightforward to read battery voltage, current-sense amplifier outputs, and thermistor bridges with one ADC and no precision reference. The SOT-23-6 footprint occupies minimal PCB area in compact handheld designs, while the I2C interface connects directly to low-power MCUs. According to the TI ADS1100 datasheet, the 8 SPS low-rate mode further reduces active current for always-on sensor sampling in IoT-style endpoints.
Рекомендуется
Consumer Sensor Read-Out Boards
The ADS1100A3IDBVRG4 serves consumer sensor hubs that digitize potentiometers, force-sensitive resistors, and analog joystick outputs, where the integrated PGA amplifies low-amplitude sensor signals and the I2C interface minimizes MCU pin count. The 16-bit resolution captures fine user-input granularity, while the self-calibration routine keeps the response drift-free over the product lifetime. Per the TI datasheet, the 4 uVp-p input-referred noise floor is low enough for haptic-feedback and gaming peripherals. The SOT-23-6 package supports ultra-compact consumer form factors.
Рекомендуется
Factory Automation Sensor Interfaces
The ADS1100A3IDBVRG4 enables factory-automation analog front-ends that read strain gauges, pressure sensors, and flow-meter bridges, taking advantage of the on-chip PGA to amplify milli-volt-level signals without external instrumentation amplifiers. The differential input rejects the large common-mode noise present on long factory cabling, while the self-calibration loop guarantees long-term stability in continuous-duty installations. The I2C bus simplifies wiring to a PLC or industrial MCU, and the 6-pin SOT-23-6 footprint fits densely populated sensor-interface cards. Per the TI datasheet, the industrial temperature range and ratiometric reference suit 24 V-bus-derived 5 V or 3.3 V supply rails.
Рекомендуется
Medical and Wellness Monitoring Devices
The ADS1100A3IDBVRG4 supports low-power medical and wellness devices such as body-worn thermistor bridges, respiration sensors, and body-impedance measurement front-ends that require high-resolution, low-noise digitization. The 16-bit resolution and continuous self-calibration capture small physiological signals accurately, while the integrated PGA eliminates external instrumentation amplifiers in space-constrained wearables. The ratiometric conversion removes dependence on absolute voltage references, simplifying FDA-style design-history documentation. Per the TI datasheet, the I2C interface shares a bus with low-power medical MCUs for compact, low-BOM wellness products.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ADS1100A3IDBVRG4 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ADS1100A0IDBVRG4 | ADS1100A4IDBVRG4 | ADS1110A1IDBVR | MCP3421A0T-E/CH |
|---|---|---|---|---|---|
| Package | SOT-23-6 | SOT-23-6 - same | SOT-23-6 - same | SOT-23-6 - same | SOT-23-6 - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Microchip Technology |
| Resolution | 16 bits | 16 bits | 16 bits | 16 bits | 18 bits |
| Max Data Rate | 128 SPS | 128 SPS | 128 SPS | 240 SPS | 60 SPS (18-bit) |
| Input Channels | 1 differential | 1 differential | 1 differential | 1 differential (true bipolar) | 1 differential |
| PGA Gains | 1 / 2 / 4 / 8 | 1 / 2 / 4 / 8 | 1 / 2 / 4 / 8 | 1 / 2 / 4 / 8 | 1 / 2 / 4 / 8 |
| Interface | I2C | I2C | I2C | I2C | I2C |
| Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
Ключевые отличия
- Continuous self-calibration eliminates periodic user calibration (против ADS1110A1IDBVR)
- Smallest 16-bit I2C ADC footprint in TI portfolio (против MCP3421A0T-E/CH)
- Programmable data rate (8/16/32/128 SPS) optimizes noise vs speed per channel (против ADS1100A0IDBVRG4)
Заметки по проектированию
The ADS1100A3IDBVRG4 uses VDD as the ratiometric reference, so any noise or drift on VDD directly couples into the conversion result. Place a 100 nF ceramic decoupling capacitor within 2 mm of the VDD pin and a 10 uF bulk capacitor on the same rail. If VDD is shared with switching converters, add a ferrite bead or pi-filter between the switching node and the ADC supply pin to attenuate switching noise that would otherwise alias into the measurement.
Route the differential analog input traces as a tightly coupled pair with equal length and minimal capacitance to ground to preserve differential balance. Keep digital I2C traces (SDA, SCL) physically separated from the analog input pin trace to avoid capacitive coupling that adds digital switching noise to the analog front-end. Per the TI ADS1100 datasheet layout recommendations, a continuous ground plane under the analog traces further reduces common-mode pickup on long sensor cables.
Add external I2C pull-up resistors (typically 4.7 kohm for 100 kHz standard mode, 2.2 kohm for 400 kHz fast mode) to VDD; the ADS1100 has open-drain SDA and SCL drivers and requires external pull-ups to function. Keep total bus capacitance below 400 pF to meet I2C timing margins. Place pull-ups at the bus master end when possible to minimize rise-time asymmetry that can cause missed acknowledge pulses.
Информация о соответствии
RoHS and lead-free compliance per the G4 suffix and TI product page. The part is not AEC-Q100 qualified and is targeted at industrial and consumer applications.