ADC121S051CIMF - 12-Bit, 500ksps SAR ADC | SOT-23-6 | TI
Артикул: ADC121S051CIMF ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $2.85 | $2,85 |
| 10 | $2.51 | $25,10 |
| 100 | $2.05 | $205,00 |
| 500 | $1.72 | $860,00 |
| 1.000 | $1.38 | $1.380,00 |
ADC121S051CIMF Обзор
A SAR (Successive Approximation Register) ADC is a class of Nyquist-rate data converter that uses a comparator, an internal DAC, and a binary-search register to digitize an input sample in N clock cycles for an N-bit result. SAR ADCs are favored over delta-sigma or pipeline types in multiplexed or power-constrained applications because they offer deterministic latency, low quiescent current (typically sub-mW), and no-pipeline-delay sampling — making the ADC121S051 a member of the data-converter -> ADC -> SAR ADC -> power-management-signal-chain hierarchy used in sensor read-out and instrumentation.
Key features include a guaranteed 12-bit no-missing-codes specification, ±1 LSB typical INL and DNL, a power-down mode that drops supply current to microampere levels between conversions, and a high-speed SPI serial interface that can stream at the full 500 ksps rate. The wide 2.7V-5.25V analog supply range lets it interface directly with 3.3V microcontrollers as well as legacy 5V signal chains, eliminating the level shifters a 1.8V-only ADC would require.
The architecture pairs an input track-and-hold with a charge-redistribution DAC and a comparator clocked by the SPI SCLK. The internal reference is the analog supply VA, simplifying BOM cost and external routing while still achieving the rated linearity at 500 ksps across the full temperature range.
Typical applications include portable instrumentation, pen tablets and touch-screen controllers, factory automation sensor modules, low-cost oscilloscope front ends, and general-purpose microcontroller data acquisition where a single 12-bit channel is sufficient. The SOT-23-6 footprint also makes it appropriate for space-constrained PCBAs.
When designing with this device, ensure VA and the digital logic supply are well bypassed with a 0.1 µF ceramic capacitor close to the supply pin, and keep the analog input trace short and guarded to preserve 12-bit linearity. Use the CS/SCLK framing of the SPI interface correctly — CS must be held low for the full 16 SCLK cycles that constitute a conversion frame.
Аналоги без доработки для ADC121S051CIMF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ADC121S051CIMF (тот же форм-фактор и посадочное место) — отличается по Digital Interface, Package, Sample Rate, Resolution, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ADC121S051CIMF/NOPB
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC121S101CIMF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC121S101CIMFX
✅ Прямая замена✓ В наличии
$1.85 / шт.
Открыть даташит →ADC101S021CISDX
✅ Прямая замена✓ В наличии
$1.32 / шт.
Открыть даташит →ADC101S021CIMFX
✅ Прямая замена✓ В наличии
$1.4 / шт.
Открыть даташит →ADC081S051CISDX/NOPB
✅ Прямая замена✓ В наличии
$1.62 / шт.
Открыть даташит →ADC081S051CISD
✅ Прямая замена✓ В наличии
$1.85 / шт.
Открыть даташит →ADC121S051CIMF Максимальные параметры и электрические характеристики
| Разрешение | 12 bit |
| Sample Rate | 200 to 500 ksps |
| Architecture | SAR (Successive Approximation Register) |
| Number of Channels | 1 |
| Input Type | Single-ended |
| Analog Supply Voltage (VA) | 2.7 V to 5.25 V |
| Digital Supply Voltage (VD) | 2.7 V to VA |
| Analog Input Voltage Range | 0 V to VA |
| Reference | Supply-referenced (VA) |
| Digital Interface | SPI / QSPI / MICROWIRE-compatible |
| Диапазон рабочих температур | -40 C to +85 C |
| Корпус | SOT-23-6 (DBV) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Конфигурация выводов ADC121S051CIMF
| Контакт 1 | VA — Analog supply voltage (2.7V to 5.25V) |
| Контакт 2 | VIN — Analog input (single-ended, 0V to VA) |
| Контакт 3 | GND — Ground |
| Контакт 4 | DOUT — Serial data output (SPI) |
| Контакт 5 | SCLK — Serial clock input |
| Контакт 6 | CS — Chip select, active low |
Типичное применение
ADC121S051CIMF подходит для 6 применениеs: Portable Sensor Data Acquisition, Pen Tablet and Touch Screen Digitizer, Industrial Process Sensor Modules, Low-Cost Oscilloscope or DMM Front End, General Microcontroller Data Acquisition, Battery-Powered IoT Sensor Nodes.
Portable Sensor Data Acquisition
The ADC121S051CIMF's 500 ksps sample rate and 12-bit resolution fit portable sensor read-out boards where a single channel digitizes temperature, pressure, or strain-gauge signals in front of a 3.3V microcontroller. With 2.7V-5.25V single-supply operation it draws supply current directly from a Li-ion or USB rail; the SOT-23-6 footprint leaves room for the sensor, op-amp front end, and MCU on a 25 mm² PCB. Compared with discrete SAR designs, the integrated SPI interface eliminates a separate sample-clock buffer.
Рекомендуется
Pen Tablet and Touch Screen Digitizer
Touch-screen controllers and EMR pen tablets typically digitize a single analog channel from the sensor matrix at 200-500 ksps, which is the ADC121S051CIMF's native operating window. The 12-bit resolution provides 4096 pressure/position levels while the SPI interface allows the host MCU to read samples synchronously with pen scans. Its small SOT-23-6 package keeps the BOM area under 9 mm², critical for the slim stylus form factor.
Рекомендуется
Industrial Process Sensor Modules
Factory-automation sensor modules (4-20 mA loop monitors, thermocouple interfaces, vibration probes) digitize one analog channel at a time at modest rates. The ADC121S051CIMF's single-ended 0-VA input range, -40°C to +85°C industrial temperature rating, and SPI output are well matched to microcontroller-based sensor conditioning. The wide 2.7-5.25V supply lets the same ADC work in 3.3V and 24V-derived 5V industrial systems.
Рекомендуется
Low-Cost Oscilloscope or DMM Front End
Handheld DMMs and entry-level scopes often use a single 12-bit ADC channel sampled at hundreds of ksps to digitize conditioned analog inputs. The ADC121S051CIMF's 500 ksps ceiling supports audio-bandwidth measurement (Nyquist ~250 kHz) and its SPI output simplifies FPGA- or MCU-based capture. The SOT-23-6 package keeps the front-end BOM area small enough for handheld enclosures.
Рекомендуется
General Microcontroller Data Acquisition
Most 8-bit and 32-bit microcontrollers lack a built-in 12-bit ADC at 500 ksps, so designers pair the MCU with an external SAR like the ADC121S051CIMF. The SPI interface drops directly into the MCU's hardware SPI peripheral; CS, SCLK, and DOUT map cleanly to standard pins. With the /CS pin pulled low, the ADC produces one 12-bit sample per 16 SCLK cycles, simplifying ISR design.
Рекомендуется
Battery-Powered IoT Sensor Nodes
Battery-powered IoT nodes occasionally need a fast burst of 12-bit samples (e.g., vibration or audio edge detection) before returning to sleep. The ADC121S051CIMF supports this with its power-down mode that drops supply current to microampere levels between conversions, while still being able to deliver 500 ksps on demand. The SOT-23-6 footprint and 2.7V minimum supply work directly with single-cell Li-ion chemistries.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ADC121S051CIMF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ADC121S051CIMF/NOPB | ADC121S101CIMF | ADC121S101CIMFX | ADC101S021CISDX | ADC101S021CIMFX | ADC081S051CISDX/NOPB | ADC081S051CISD |
|---|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOT-23-6 (DBV) | SOT-23-6 (DBV) - same | SOT-23-6 (DBV) - same | SOT-23-6 (DBV) - same | SOT-23-6 (DBV) - same | SOT-23-6 (DBV) - same | SOT-23-6 (DBV) - same | SOT-23-6 (DBV) - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 10 bit | 10 bit | 8 bit | 8 bit |
| Max Sample Rate | 500 ksps | 500 ksps | 1 Msps | 1 Msps | 200 ksps | 200 ksps | 500 ksps | 500 ksps |
| Architecture | SAR | SAR | SAR | SAR | SAR | SAR | SAR | SAR |
| Analog Supply Range | 2.7V to 5.25V | 2.7V to 5.25V | 2.7V to 5.25V | 2.7V to 5.25V | 2.7V to 5.25V | 2.7V to 5.25V | 2.7V to 5.25V | 2.7V to 5.25V |
| Digital Interface | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE | SPI/QSPI/MICROWIRE |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Lead-Free / RoHS | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
Ключевые отличия
- Family-wide pin compatibility across 8/10/12-bit resolutions (против ADC081S051CISD, ADC101S021CISDX)
- Higher sample rate than the 10-bit family member (против ADC101S021CISDX)
- Lower cost than the 1 Msps variant at equivalent pinout (против ADC121S101CIMF)
- Wide 2.7V-5.25V supply eliminates level shifters (против Competitor ADCs requiring 1.8V or 3.0V supplies)
Заметки по проектированию
Place a 0.1 µF ceramic bypass capacitor as close as possible to the VA pin (pin 1) and a 10 µF bulk capacitor nearby to provide the instantaneous charge that a SAR ADC draws during conversion. Per the TI datasheet, supply-noise amplitude is the dominant source of ADC121S051CIMF linearity degradation; insufficient decoupling can cost several LSBs at 500 ksps. Estimated: at 500 ksps each conversion draws a transient of several mA from VA for ~1 µs, so the high-frequency capacitor must be within 2 mm of the pin.
Route the analog input (pin 2, VIN) trace as a short, guarded path away from the SPI lines (SCLK, DOUT, CS) on pins 4-6. The SOT-23-6 package has limited pin-to-pin isolation, so cross-coupling from the digital SPI bus into the analog input at high SCLK frequencies can degrade SNR. A grounded guard trace on both sides of VIN is recommended when sample rate exceeds 200 ksps.
Drive CS low for exactly 16 SCLK cycles per conversion frame; releasing CS earlier aborts the conversion. Per TI's SPI timing diagram, SCLK idle-low mode (CPOL=0) and data clocked on the rising edge (CPHA=0) are the standard convention. Driving SCLK faster than the datasheet maximum (typically 25 MHz) will result in incomplete conversions and corrupted data.
The ADC121S051CIMF has an internal power-down mode triggered by holding CS high for more than the power-down timeout (~1 ms typical, refer to datasheet exact value). Per the datasheet, supply current drops to microampere levels in this state, making the part suitable for battery-powered duty-cycled applications. Wake-up time on CS-low is typically less than 1 µs — verify against your timing budget for short-duration bursts.
Информация о соответствии
RoHS and lead-free per TI product page. AEC-Q100 not applicable for the SOT-23-6 industrial temperature grade. /NOPB suffix indicates lead-free terminal finish.