ATMEGA328P-MMHR - 20MHz 32KB Flash 8-Bit MCU | Microchip
Артикул: ATMEGA328P-MMHR ✓ АктивенATMEGA328P-MMHR Обзор
An 8-bit AVR microcontroller is a programmable semiconductor that combines a CPU core, Flash program memory, SRAM, EEPROM, timers, serial interfaces, and GPIO in one integrated circuit. Within the product hierarchy, it belongs to the AVR family of reduced-instruction-set microcontrollers, commonly called an MCU. Its integrated memory and peripherals allow a compact embedded design to replace separate processor, program-memory, and interface components.
The ATMEGA328P-MMHR provides 32 KB of read-while-write Flash, 2 KB of SRAM, and 1 KB of EEPROM according to the manufacturer-family datasheet result. Its feature set includes 32 general-purpose working registers, 23 I/O lines, a real-time counter, three flexible timer/counter blocks with compare and PWM modes, one USART, one two-wire serial interface, and a six-channel 10-bit ADC. These resources support compact control, sensing, communications, and actuator workloads.
The enhanced RISC-based AVR architecture executes most instructions in a single clock cycle, while the device supports clock frequencies up to 20 MHz for the ATMEGA328P-MMHR listing. Its peripherals reduce the need for external logic: PWM channels can drive indicators or power stages, the ADC can sample analog inputs, and the USART and I2C interface can connect sensors, displays, and service adapters. The 28-pin VQFN also supports high-density PCB placement, although its exposed-pad construction requires careful thermal design.
Typical uses include Arduino-compatible sensor nodes, compact industrial controllers, LED and motor-control boards, environmental monitoring products, and low-cost connected instruments. The 23 I/O lines provide external signal connections, while the 1 KB EEPROM is useful for retaining small configuration values. The 20 MHz clock also provides sufficient timing resolution for common control-loop, communication, and measurement tasks.
When laying out a board, follow the manufacturer pinout and land-pattern requirements rather than relying on generic QFN conventions. Provide the required supply decoupling at the power pins, route the exposed pad according to the package thermal guidance, and keep sensitive analog inputs away from high-current switching paths. Confirm the selected crystal or clock arrangement, programming interface, and fuse settings before releasing a production PCB.
This page consolidates verified distributor specifications, source-linked pricing and availability information, package details, and practical selection guidance. It also distinguishes a genuine same-package drop-in candidate from other ATmega devices whose package, pin count, or device features prevent unqualified substitution.
Аналоги без доработки для ATMEGA328P-MMHR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATMEGA328P-MMHR (тот же форм-фактор и посадочное место) — отличается по RoHS Status, Package, Flash Memory, Communication Interfaces, EEPROM.
ATMEGA328P-MMH
✅ Прямая заменаУточнить цену
Открыть даташит →ATMEGA328-MMH
✅ Прямая заменаУточнить цену
Открыть даташит →ATMEGA328P-MMHR Максимальные параметры и электрические характеристики
| Product Type | 8-bit AVR Microcontroller |
| Maximum Clock Speed | 20 MHz |
| Flash Memory | 32 KB |
| Program Memory Organization | 16K x 16 |
| SRAM | 2 KB |
| EEPROM | 1 KB |
| General-Purpose I/O Lines | 23 lines |
| General-Purpose Working Registers | 32 |
| ADC Resolution | 10-bit |
| ADC Channels | 6 channels |
| Timer/Counters | 3 |
| Serial Interfaces | 1 USART and 1 two-wire serial interface |
| Корпус | 28-pin VQFN, 4 x 4 mm |
| Тип монтажа | Surface Mount |
| Напряжение питания | 4.5 V to 5.5 V |
| Real-Time Counter | Integrated |
| PWM Support | Yes, timer/counter compare modes support PWM |
| Статус жизненного цикла | Active |
| Статус RoHS | unknown |
| REACH Status | unknown |
Руководство по цоколевке ATMEGA328P-MMHR в корпусе 28-pin vqfn, 4 x 4 mm
Цоколевка для ATMEGA328P-MMHR (корпус 28-pin vqfn, 4 x 4 mm). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для ATMEGA328P-MMHR.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
ATMEGA328P-MMHR подходит для 6 применениеs: Arduino-Compatible Sensor Node, Compact Industrial Control Module, LED and Motor Control Board, Environmental Monitoring Instrument, Programmable Logic Controller, USB-UART Development Interface.
Arduino-Compatible Sensor Node
The ATMEGA328P-MMHR fits compact Arduino-compatible sensor nodes because it combines a 20 MHz AVR core, 32 KB of Flash, 2 KB of SRAM, and 23 general-purpose I/O lines in a 28-pin VQFN. Its six-channel 10-bit ADC can sample analog sensors, while one USART and one two-wire serial interface support host communication and external peripherals. The 4 x 4 mm package saves board area compared with larger leaded or TQFP devices, although the exposed-pad footprint requires manufacturer-compliant PCB construction. Firmware and peripheral assignments should be verified against the exact package pinout before production.
Рекомендуется
Compact Industrial Control Module
The ATMEGA328P-MMHR is suitable for compact industrial control modules that combine digital inputs, status indication, local sensing, and serial diagnostics. Its 20 MHz operating capability supports responsive timer/counter and PWM functions, while 23 I/O lines provide enough external connections for typical auxiliary control tasks. The three timer/counter blocks can support timing, capture, compare, and PWM workloads without additional timer ICs. For a compact control board, the 28-pin VQFN reduces area, but designers should provide robust decoupling, protected I/O paths, and thermal copper under the exposed pad according to the manufacturer package guidance.
Рекомендуется
LED and Motor Control Board
The ATMEGA328P-MMHR works well in small LED and motor-control boards because its three timer/counter blocks provide compare and PWM modes alongside 23 general-purpose I/O lines. It can generate timing signals for dimming, position indicators, or low-power motor drive stages while its ADC monitors feedback or supply conditions. At a maximum clock of 20 MHz, software timing remains responsive for many inexpensive control loops. The 28-pin VQFN allows a dense layout, but motor wiring can introduce transients; use suitable driver electronics, grounding, and isolation or filtering rather than driving loads directly from MCU pins.
Рекомендуется
Environmental Monitoring Instrument
The ATMEGA328P-MMHR can serve as the controller in a compact environmental monitor where periodic analog sampling and low-power serial reporting are required. Its six-channel 10-bit ADC supports multiple sensor inputs, while 1 KB of EEPROM can retain calibration identifiers or configuration values between resets. The USART provides a straightforward diagnostic path, and the two-wire interface can connect compatible sensors or display components. Because the retrieved data does not specify detailed sleep-current or analog-accuracy limits, battery-life and precision claims should be validated using the manufacturer datasheet. Firmware should also disable unused peripherals where low power is important.
Рекомендуется
Programmable Logic Controller
The ATMEGA328P-MMHR is appropriate for small programmable logic controller tasks involving digital sequencing, timers, and compact I/O. Twenty-three general-purpose I/O lines, three timer/counter blocks, and 2 KB of working SRAM provide enough resources for modest control sequences without external logic. The 20 MHz AVR core allows responsive event handling and communication with local programming or diagnostic equipment. Firmware should include watchdog and output-state initialization where required, while the hardware design should protect inputs from industrial transients. The small VQFN footprint reduces board area but demands careful land-pattern and exposed-pad manufacturing control.
Рекомендуется
USB-UART Development Interface
The ATMEGA328P-MMHR can form the embedded side of a USB-to-UART development interface when firmware handles bootloader activation and serial data transfer. Its USART provides the data path, while 32 KB of Flash is sufficient for compact bootloaders and configuration utilities; one USART and one two-wire serial interface are available for connected accessories. A companion USB-to-UART transceiver such as the CP2102N is a natural system-level choice. Verify the selected USB bridge voltage levels and boot-reset wiring, and do not assume that every Arduino bootloader or USB driver is compatible with a custom ATMEGA328P-MMHR board.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATMEGA328P-MMHR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATMEGA328P-MMH | ATMEGA328-MMH |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-pin VQFN, 4 x 4 mm | 28-pin VQFN | 28-pin VQFN |
| Device Type | 8-bit AVR Microcontroller | 8-bit AVR Microcontroller | 8-bit AVR Microcontroller |
Ключевые отличия
- Compact 28-pin VQFN implementation of the established ATmega328P platform (против ATMEGA328P-MMH)
- 20 MHz maximum clock with integrated control and communication peripherals (против ATMEGA328-MMH)
- Compact package reduces PCB area without relying on a larger pin-count device (против ATMEGA328P-MNR)
Заметки по проектированию
Use the latest Microchip package drawing for the 28-pin VQFN rather than generating the land pattern from a generic library. Confirm pin 1 orientation, pad dimensions, solder-mask opening, exposed-pad connection, and paste stencil. Place the supply bypass capacitor adjacent to the appropriate power and ground pins, and provide a low-impedance ground return so the switching core does not share a noisy path with analog returns.
The ATMEGA328P-MMHR uses a compact VQFN package with an exposed thermal pad. Follow the manufacturer's maximum power dissipation and package thermal data, and connect the exposed pad to the intended ground plane using the specified land pattern. Estimated: at a 5.0 V supply, 3.0 V output, and 20 mA load, the regulator-style dissipation proxy is 40 mW, but actual junction temperature must be evaluated using the device's verified electrical limits and board thermal conditions.
Route oscillator, programming, reset, and communication signals away from noisy switching nodes and motor-driver wiring. Keep decoupling current paths short, use a continuous ground reference, and avoid long stubs between the MCU and passive components. If the board includes relays, displays, or wireless modules, separate their high-current returns from the MCU and ADC ground paths and add protection appropriate to the actual transient environment.
Do not treat an ATmega device with the same core description as a confirmed replacement. The ATMEGA328P-MMH and ATMEGA328-MMH candidates require verification of exact ordering suffixes, pin mapping, boot behavior, fuse defaults, electrical limits, and package revisions. Before production use, compare the manufacturer documentation, build representative firmware, test programming and reset, and validate every peripheral used by the original design.
Информация о соответствии
The supplied verified results do not provide explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statements. The search snippet mentions RoHS and REACH only as comparison fields for another product and does not establish this part's status.
