ATMEGA32A-AU - 8-bit AVR MCU, 32KB Flash, 16MHz, TQFP-44 | Microchip
Артикул: ATMEGA32A-AU ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $5.2 | $5,20 |
| 10 | $4.65 | $46,50 |
| 100 | $3.85 | $385,00 |
| 500 | $3.3 | $1.650,00 |
| 1.000 | $2.95 | $2.950,00 |
ATMEGA32A-AU Обзор
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and peripherals on one die. The AVR family in particular uses a modified Harvard architecture with a rich instruction set tuned for single-clock execution. Microcontrollers like the ATmega32A sit at the lowest tier of embedded compute, below microprocessors and SoCs, but above fixed-function controllers, and they occupy the role of configurable glue logic and decision-making in mixed-signal systems.
Key differentiating features include 8-channel 10-bit ADC, JTAG on-chip debug, two 8-bit and one 16-bit timer/counter, hardware USART, SPI, and TWI (I2C), plus 32 programmable I/O lines and six sleep modes for power-sensitive designs. The internal RC oscillator is factory-calibrated, allowing operation without an external crystal. Endurance is rated at 10,000 flash cycles and 100,000 EEPROM cycles.
Typical applications are industrial control systems, sensor interfaces, home appliances, motor-control front-ends, and hobbyist / educational platforms. With 32KB of flash and rich peripherals, the part is widely used in custom protocol bridges and human-machine interface boards.
Designers should consult the datasheet for ADC reference decoupling, JTAG pin sharing with GPIO, and brown-out detector configuration; programming requires attention to fuse bits and lock bits. The TQFP-44 (10x10 mm) footprint is pin-compatible with later ATmega32 variants and ATmega32U4 family members.
This page synthesizes distributor pricing, drop-in TQFP-44 alternatives, and practical design notes not found on the standalone datasheet.
Аналоги без доработки для ATMEGA32A-AU — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATMEGA32A-AU (тот же форм-фактор и посадочное место) — отличается по Package, Debug Interface, SRAM, Operating Temperature, Core Architecture.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATMEGA32A-ANR
✅ Прямая замена✓ В наличии
$3.32 / шт.
Открыть даташит →ATMEGA32A-AN
✅ Прямая замена✓ В наличии
$3.4 / шт.
Открыть даташит →ATMEGA32A-AUR
✅ Прямая замена✓ В наличии
$2.96 / шт.
Открыть даташит →ATMEGA329P-20AU
✅ Прямая замена✓ В наличии
$4.71 / шт.
Открыть даташит →ATMEGA329-16AU
✅ Прямая замена✓ В наличии
$8.45 / шт.
Открыть даташит →ATMEGA3290V-8AU
✅ Прямая замена✓ В наличии
$3.91 / шт.
Открыть даташит →ATMEGA32A-AU Максимальные параметры и электрические характеристики
| Manufacturer | Microchip Technology (formerly Atmel) |
| Series | AVR ATmega |
| Core Architecture | AVR RISC 8-bit |
| Максимальная тактовая частота | 16 MHz |
| MIPS Throughput | 16 MIPS at 16 MHz |
| Program Memory (Flash) | 32 KB |
| SRAM | 2 KB |
| EEPROM | 1 KB |
| Operating Voltage Range | 2.7 V to 5.5 V |
| I/O Pins | 32 programmable |
| ADC | 8-channel, 10-bit |
| Timers/Counters | Two 8-bit and one 16-bit |
| Communication Peripherals | USART, SPI, TWI (I2C) |
| Debug Interface | JTAG (IEEE 1149.1 compliant) |
| Корпус | 44-pin TQFP (10x10 mm, 0.8 mm pitch) |
| Тип монтажа | Surface Mount |
| Рабочая температура | -40C to +85C (industrial) |
| Статус RoHS | Compliant (Green) |
Конфигурация выводов ATMEGA32A-AU
| Контакт 1 | PB5 (MOSI) — Port B bit 5 / SPI MOSI (or JTAG TDI via JTAGEN fuse) |
| Контакт 2 | PB6 (MISO) — Port B bit 6 / SPI MISO (or JTAG TDO via JTAGEN fuse) |
| Контакт 3 | PB7 (SCK) — Port B bit 7 / SPI SCK (or JTAG TMS via JTAGEN fuse) |
| Контакт 4 | RESET — Reset input, active low |
| Контакт 5 | VCC — Digital supply voltage (2.7V to 5.5V) |
| Контакт 6 | GND — Ground |
| Контакт 7 | XTAL2 — Crystal oscillator output |
| Контакт 8 | XTAL1 — Crystal oscillator input or external clock |
| Контакт 9 | PD0 (RXD) — Port D bit 0 / USART RXD |
| Контакт 10 | PD1 (TXD) — Port D bit 1 / USART TXD |
| Контакт 11 | PD2 (INT0) — Port D bit 2 / External Interrupt 0 |
| Контакт 12 | PD3 (INT1) — Port D bit 3 / External Interrupt 1 |
| Контакт 13 | PD4 (OC1B) — Port D bit 4 / Timer1 Compare B |
| Контакт 14 | PD5 (OC1A) — Port D bit 5 / Timer1 Compare A |
| Контакт 15 | PD6 (ICP1) — Port D bit 6 / Timer1 Input Capture |
| Контакт 16 | PD7 (OC2) — Port D bit 7 / Timer2 Compare |
| Контакт 17 | VCC — Digital supply voltage |
| Контакт 18 | GND — Ground |
| Контакт 19 | PC0 (ADC0) — Port C bit 0 / ADC channel 0 |
| Контакт 20 | PC1 (ADC1) — Port C bit 1 / ADC channel 1 |
| Контакт 21 | PC2 (ADC2) — Port C bit 2 / ADC channel 2 |
| Контакт 22 | PC3 (ADC3) — Port C bit 3 / ADC channel 3 |
| Контакт 23 | PC4 (ADC4 / SDA) — Port C bit 4 / ADC4 / I2C SDA |
| Контакт 24 | PC5 (ADC5 / SCL) — Port C bit 5 / ADC5 / I2C SCL |
| Контакт 25 | PC6 (TOSC1) — Port C bit 6 / Timer0 Oscillator pin 1 |
| Контакт 26 | PC7 (TOSC2) — Port C bit 7 / Timer0 Oscillator pin 2 |
| Контакт 27 | AVCC — Analog supply for ADC (tie to VCC) |
| Контакт 28 | AREF — ADC reference voltage |
| Контакт 29 | AGND — Analog ground |
| Контакт 30 | PA7 (ADC7) — Port A bit 7 / ADC channel 7 |
| Контакт 31 | PA6 (ADC6) — Port A bit 6 / ADC channel 6 |
| Контакт 32 | PA5 (ADC5) — Port A bit 5 / ADC channel 5 |
| Контакт 33 | PA4 (ADC4) — Port A bit 4 / ADC channel 4 |
| Контакт 34 | PA3 (ADC3) — Port A bit 3 / ADC channel 3 |
| Контакт 35 | PA2 (ADC2) — Port A bit 2 / ADC channel 2 |
| Контакт 36 | PA1 (ADC1) — Port A bit 1 / ADC channel 1 |
| Контакт 37 | PA0 (ADC0) — Port A bit 0 / ADC channel 0 |
| Контакт 38 | VCC — Digital supply voltage |
| Контакт 39 | GND — Ground |
| Контакт 40 | PB0 (SS) — Port B bit 0 / SPI Slave Select |
| Контакт 41 | PB1 (SCK) — Port B bit 1 / SPI SCK (alt) |
| Контакт 42 | PB2 (MOSI) — Port B bit 2 / SPI MOSI (alt) / OC3B |
| Контакт 43 | PB3 (MISO) — Port B bit 3 / SPI MISO (alt) / OC3A |
| Контакт 44 | PB4 (OC0) — Port B bit 4 / Timer0 Compare |
Типичное применение
ATMEGA32A-AU подходит для 6 применениеs: Industrial Sensor Hub, Home Appliance Control Board, HVAC Fan / Pump Motor Control, Educational / Maker Embedded Platform, Custom Protocol Bridge (SPI/I2C to UART), Battery-Powered Wireless Sensor Node.
Industrial Sensor Hub
The ATMEGA32A-AU is well-suited as the host MCU of an industrial sensor hub because its 8-channel 10-bit ADC can digitize up to eight analog sensors simultaneously, while its 32 programmable I/O lines drive digital sensors and indicator LEDs. Its 2.7V to 5.5V operating range allows direct interface to 3.3V sensors and 5V industrial backplanes without level shifters. The 16 MHz clock provides 16 MIPS, sufficient for moving-average filtering, linearization, and Modbus RTU framing on the USART before forwarding data upstream.
Рекомендуется
Home Appliance Control Board
In washing-machine, dishwasher, and microwave oven front panels, the ATMEGA32A-AU provides capacitive-touch scanning via timer/counter capture, drives character LCDs or segment LEDs, and reads rotary encoders. The 32KB flash is sufficient for UI state machines, while the 2KB SRAM handles display buffers. Six sleep modes let the MCU idle at <1 uA between user inputs, an important parameter for ENERGY STAR-rated appliances. JTAG allows production-line firmware update without bootloader boot pins.
Рекомендуется
HVAC Fan / Pump Motor Control
The 16-bit timer/counter combined with the ATmega32A's complementary PWM channels drives brushed DC fans and small pumps via MOSFET half-bridges, while the ADC samples back-EMF or current-sense shunts for closed-loop speed control. Hardware SPI simplifies digital potentiometer or external DAC biasing. Operating reliably from -40C to +85C industrial grade, the part survives attic and boiler-room installations. The 2KB SRAM allows simple PI controller state to be stored without external memory.
Рекомендуется
Educational / Maker Embedded Platform
For university microcontroller courses and maker projects, the ATMEGA32A-AU offers a generous 32KB flash that fits substantial teaching labs while keeping the JTAG debug workflow accessible via low-cost AVR Dragon or JTAGICE clones. The TQFP-44 breakout board exposes 32 GPIO for breadboarding, and Arduino-style frameworks have been ported to it (MightyCore). Compared to ATmega328P, the ATmega32A doubles the flash and adds JTAG, ideal for teaching embedded C with real breakpoints rather than bootloader printf debugging.
Рекомендуется
Custom Protocol Bridge (SPI/I2C to UART)
Protocol-bridge modules that translate between I2C sensors and UART-based industrial controllers are a common use of the ATMEGA32A-AU. The TWI (I2C) hardware slave can address up to 128 nodes, while the USART supports RS-232 or RS-485 framing via an external transceiver. With 32KB flash, the part can hold multiple protocol stacks (Modbus, NMEA, vendor-specific) and select between them at boot. JTAG simplifies firmware bring-up when integrating with legacy protocols.
Рекомендуется
Battery-Powered Wireless Sensor Node
With six software-selectable sleep modes, the ATMEGA32A-AU can drop to <1 uA current between sensor reads, making it suitable for wireless sensor nodes powered by 2xAA batteries. The 8-channel ADC handles multiple sensor inputs (temperature, humidity, light, gas), and the SPI bus connects to sub-GHz radio modules such as RFM69 or LoRa. Brown-out detection prevents corruption of EEPROM-stored calibration constants when the cell voltage drops below 2.7V. Operating voltage of 2.7V to 5.5V covers the full NiMH / alkaline discharge curve.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATMEGA32A-AU — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATMEGA32A-ANR | ATMEGA32A-AN | ATMEGA32A-AUR | ATmega329P-20AU |
|---|---|---|---|---|---|
| Package | TQFP-44 (10x10 mm) | TQFP-44 (10x10 mm) | TQFP-44 (10x10 mm) | TQFP-44 (10x10 mm) | TQFP-44 (10x10 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| Max Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 20 MHz |
| Operating Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 1.8 V to 5.5 V |
| ADC Channels | 8 channels x 10-bit | 8 channels x 10-bit | 8 channels x 10-bit | 8 channels x 10-bit | 8 channels x 10-bit |
| JTAG Debug | Yes | Yes | Yes | Yes | Yes |
| Packaging | Tray | Tape & Reel | Tray | Tape & Reel | Tray |
Ключевые отличия
- JTAG debug vs ISP-only ATmega328P (против ATmega328P-PU)
- TQFP-44 vs DIP-28 ATmega32A-PU (против ATMEGA32A-PU)
- 8-channel 10-bit ADC vs no-ADC ATMEGA32L (против ATMEGA32L-8AI)
Заметки по проектированию
Estimated: At VCC = 5V, 16 MHz, the ATmega32A draws approximately 12 mA in active mode per the Microchip datasheet DC characteristics. Decouple VCC with a 100 nF X7R ceramic placed within 5 mm of each VCC pin and a single 10 uF tantalum or polymer bulk cap near pin 5. AVCC (pin 27) must be tied to VCC through a ferrite bead or 10 ohm resistor and have its own 100 nF + 10 uF decoupling to suppress ADC reference noise.
JTAGEN fuse defaults ON, so the four JTAG pins (PB5-PB7, plus TCK on PB6) are hijacked for boundary-scan after reset. If you need those pins as standard SPI or GPIO, clear the JTAGEN fuse in the extended fuse byte. Also, the RESET pin (pin 4) is used as GPIO only after disabling the RSTDISBL fuse - a one-way operation that bricks further ISP if not planned correctly.
Keep the crystal traces (XTAL1/XTAL2) short and symmetric. Place the crystal within 10 mm of the MCU with a guard ground ring to limit radiated EMI. For low-power designs, set unused pins to output-low with internal pull-ups disabled; configure unused ADC channels to reduce AVDD switching noise. Layout the TQFP-44 footprint with 0.8 mm pitch traces, using microvia-in-pad for thermal pad if extended thermal dissipation is needed.
The TWI (I2C) pins (PC4/PC5) operate as open-drain and require external pull-ups sized by bus capacitance: 4.7 kohm for <10 cm traces on the same PCB, dropping to 2.2 kohm or 1 kohm for 1 m external buses. The hardware USART can run up to 250 kbps reliably; for higher speeds, sample the asynchronous clock using the crystal-locked baud-rate generator. Avoid driving the ADC and I2C lines in parallel to prevent digital switching noise from coupling into the analog input.
Информация о соответствии
RoHS and REACH compliant per Microchip product page. Industrial temperature grade -40C to +85C. Not AEC-Q100 qualified - use automotive-qualified AVR MCU variants if required.