ATMEGA64-16AU - 8-bit AVR MCU 64KB Flash 16MHz | Microchip
Артикул: ATMEGA64-16AU ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $11.3 | $11,30 |
| 10 | $10.17 | $101,70 |
| 100 | $9.04 | $904,00 |
| 500 | $8.14 | $4.070,00 |
| 1.000 | $7.23 | $7.230,00 |
ATMEGA64-16AU Обзор
An AVR microcontroller is a single-chip computer built on the enhanced RISC architecture originally developed by Atmel (now Microchip Technology). It integrates CPU, non-volatile program memory, data memory, and peripherals such as timers, serial interfaces, and analog-to-digital converters on one die. In the product hierarchy, the ATmega64 sits within the AVR 8-bit MCU family, which belongs to the broader microcontroller category under embedded processing semiconductors.
Key features include 64 KB Flash with Read-While-Write capability, 4 KB internal SRAM, 2 KB EEPROM, a real-time counter (RTC), four flexible timer/counters with compare modes and PWM, two USARTs, a byte-oriented Two-wire serial interface, and an 8-channel 10-bit ADC. The device supports both 5V and 3.3V operation and offers six sleep modes for power-sensitive designs.
The ATmega64 is 100% pin compatible with the legacy ATmega103, allowing direct replacement on existing printed circuit boards. Its JTAG interface supports IEEE 1149.1 boundary-scan and on-chip debug, while the self-programming Flash enables in-system firmware updates without removing the device from the board.
Typical applications include industrial automation controllers, motor control, sensor hubs, building automation nodes, battery-powered instrumentation, and legacy ATmega103 board upgrades. The 53 I/O lines and dual USARTs make it well suited to multi-interface gateway designs.
When designing with the ATMEGA64-16AU, decouple every VCC pin with a 100 nF ceramic capacitor placed close to the pin, and use a low-ESR crystal with matched load capacitors on XTAL1/XTAL2 for reliable 16 MHz operation. Keep the analog AVCC supply filtered through a ferrite bead for ADC accuracy.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selection, replacement, and layout decisions.
Аналоги без доработки для ATMEGA64-16AU — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATMEGA64-16AU (тот же форм-фактор и посадочное место) — отличается по RoHS Status, Package, ADC, Operating Temperature, Debug Interface.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATMEGA64-16AUR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATMEGA64-16AC
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ATMEGA64L-8AU
✅ Прямая замена✓ В наличии
$4.55 / шт.
Открыть даташит →ATMEGA128-16AU
✅ Прямая замена✓ В наличии
$14.3 / шт.
Открыть даташит →ATMEGA128-16AUR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATMEGA64A-AU
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ATMEGA64-16AU Максимальные параметры и электрические характеристики
| Core Architecture | 8-bit AVR RISC |
| Program Memory Size | 64 KB Flash (32K x 16) |
| Flash Endurance | 10,000 write/erase cycles |
| SRAM | 4 KB |
| EEPROM | 2 KB |
| Maximum CPU Speed | 16 MHz |
| Throughput | Up to 16 MIPS at 16 MHz |
| General Purpose I/O Pins | 53 |
| General Purpose Working Registers | 32 |
| Operating Voltage | 4.5 V to 5.5 V (16 MHz); 2.7 V to 5.5 V (8 MHz) |
| Timer/Counters | 4 (two 8-bit, two 16-bit) with compare modes and PWM |
| USART Interfaces | 2 |
| Two-wire Serial Interface | 1 (byte oriented) |
| ADC | 8-channel, 10-bit |
| Real Time Counter | Yes (RTC) |
| Корпус | 64-TQFP (14x14 mm, 0.8 mm pitch) |
| Тип монтажа | Surface Mount |
| Рабочая температура | -40 C to +85 C |
| Статус RoHS | Compliant (GREEN) |
| JTAG Debug Interface | Yes (IEEE 1149.1 boundary-scan) |
Конфигурация выводов ATMEGA64-16AU
| Контакт 1 | PE6/RXD0/INT6 — Port E bit 6 / USART0 receive / external interrupt 6 |
| Контакт 2 | PE7/TXD0/INT7 — Port E bit 7 / USART0 transmit / external interrupt 7 |
| Контакт 3 | PB0/SS/SCK — Port B bit 0 / SPI slave select / SPI clock |
| Контакт 4 | PB1/MISO/OC0 — Port B bit 1 / SPI master-in slave-out / timer0 output compare |
| Контакт 5 | PB2/MOSI/OC1B — Port B bit 2 / SPI master-out slave-in / timer1 output compare B |
| Контакт 6 | PB3/OC2A — Port B bit 3 / timer2 output compare A |
| Контакт 7 | PB4/OC2B — Port B bit 4 / timer2 output compare B |
| Контакт 8 | PB5/OC1A — Port B bit 5 / timer1 output compare A |
| Контакт 9 | PB6/OC1B — Port B bit 6 / timer1 output compare B |
| Контакт 10 | PB7/OC0/OC2 — Port B bit 7 / timer0 and timer2 output compare |
| Контакт 11 | TOSC2/PG3 — Timer oscillator pin 2 / port G bit 3 |
| Контакт 12 | TOSC1/PG4 — Timer oscillator pin 1 / port G bit 4 |
| Контакт 13 | RESET — Reset input (active low) |
| Контакт 14 | VCC — Digital supply voltage |
| Контакт 15 | GND — Ground |
| Контакт 16 | XTAL2 — Crystal oscillator output |
| Контакт 17 | XTAL1 — Crystal oscillator input / external clock |
| Контакт 18 | PD0/SCL/INT0 — Port D bit 0 / Two-wire clock / external interrupt 0 |
| Контакт 19 | PD1/SDA/INT1 — Port D bit 1 / Two-wire data / external interrupt 1 |
| Контакт 20 | PD2/RXD1/INT2 — Port D bit 2 / USART1 receive / external interrupt 2 |
| Контакт 21 | PD3/TXD1/INT3 — Port D bit 3 / USART1 transmit / external interrupt 3 |
| Контакт 22 | PD4/IC1 — Port D bit 4 / timer1 input capture |
| Контакт 23 | PD5/XCK1 — Port D bit 5 / USART1 external clock |
| Контакт 24 | PD6/T1 — Port D bit 6 / timer1 external counter input |
| Контакт 25 | PD7/T2 — Port D bit 7 / timer2 external counter input |
| Контакт 26 | PC0/A8 — Port C bit 0 / ADC channel 8 |
| Контакт 27 | PC1/A9 — Port C bit 1 / ADC channel 9 |
| Контакт 28 | PC2/A10 — Port C bit 2 / ADC channel 10 |
| Контакт 29 | PC3/A11 — Port C bit 3 / ADC channel 11 |
| Контакт 30 | PC4/A12 — Port C bit 4 / ADC channel 12 |
| Контакт 31 | PC5/A13 — Port C bit 5 / ADC channel 13 |
| Контакт 32 | PC6/A14 — Port C bit 6 / ADC channel 14 |
| Контакт 33 | PC7/A15 — Port C bit 7 / ADC channel 15 |
| Контакт 34 | PG0/WR — Port G bit 0 / external memory write strobe |
| Контакт 35 | PG1/RD — Port G bit 1 / external memory read strobe |
| Контакт 36 | PG2/ALE — Port G bit 2 / external memory address latch enable |
| Контакт 37 | PA7/AD7 — Port A bit 7 / external memory address/data bus |
| Контакт 38 | PA6/AD6 — Port A bit 6 / external memory address/data bus |
| Контакт 39 | PA5/AD5 — Port A bit 5 / external memory address/data bus |
| Контакт 40 | PA4/AD4 — Port A bit 4 / external memory address/data bus |
| Контакт 41 | PA3/AD3 — Port A bit 3 / external memory address/data bus |
| Контакт 42 | PA2/AD2 — Port A bit 2 / external memory address/data bus |
| Контакт 43 | PA1/AD1 — Port A bit 1 / external memory address/data bus |
| Контакт 44 | PA0/AD0 — Port A bit 0 / external memory address/data bus |
| Контакт 45 | VCC — Digital supply voltage |
| Контакт 46 | GND — Ground |
| Контакт 47 | PF7/ADC7/TDI — Port F bit 7 / ADC channel 7 / JTAG test data in |
| Контакт 48 | PF6/ADC6/TDO — Port F bit 6 / ADC channel 6 / JTAG test data out |
| Контакт 49 | PF5/ADC5/TMS — Port F bit 5 / ADC channel 5 / JTAG test mode select |
| Контакт 50 | PF4/ADC4/TCK — Port F bit 4 / ADC channel 4 / JTAG test clock |
| Контакт 51 | PF3/ADC3 — Port F bit 3 / ADC channel 3 |
| Контакт 52 | PF2/ADC2 — Port F bit 2 / ADC channel 2 |
| Контакт 53 | PF1/ADC1 — Port F bit 1 / ADC channel 1 |
| Контакт 54 | PF0/ADC0 — Port F bit 0 / ADC channel 0 |
| Контакт 55 | AREF — Analog reference voltage for ADC |
| Контакт 56 | GND — Ground |
| Контакт 57 | AVCC — Analog supply voltage for ADC |
| Контакт 58 | PE2/ALE — Port E bit 2 / external memory address latch enable |
| Контакт 59 | PE3/OC3A — Port E bit 3 / timer3 output compare A |
| Контакт 60 | PE4/OC3B — Port E bit 4 / timer3 output compare B |
| Контакт 61 | PE5/OC3C — Port E bit 5 / timer3 output compare C |
| Контакт 62 | PE0/RXD0/INT8 — Port E bit 0 / USART0 receive / external interrupt 8 |
| Контакт 63 | PE1/TXD0 — Port E bit 1 / USART0 transmit |
| Контакт 64 | PEN — Programming enable (SPI programming) |
Типичное применение
ATMEGA64-16AU подходит для 6 применениеs: Industrial Automation Controller, Motor Control and Drive, Legacy ATmega103 Board Upgrade, Battery-Powered Instrumentation, Multi-Interface Communication Gateway, Building Automation Node.
Industrial Automation Controller
The ATMEGA64-16AU fits industrial automation controllers because its 53 general-purpose I/O lines, four timer/counters with PWM, and dual USARTs allow a single chip to drive relays, read limit switches, and communicate on two serial buses simultaneously. Running at 16 MHz from a 5 V rail, it executes control loops at up to 16 MIPS, which is sufficient for PLC-style ladder logic and PID motor control. The 8-channel 10-bit ADC samples analog sensors such as thermocouples and pressure transducers directly, eliminating external converter chips. The -40 C to +85 C operating range and 64-pin TQFP package suit DIN-rail mounted hardware. A typical implementation places the MCU behind opto-isolated inputs and uses one USART for Modbus RTU and the other for a local HMI link, with the 2 KB EEPROM storing calibration constants across power cycles.
Рекомендуется
Motor Control and Drive
The ATMEGA64-16AU is used in motor control because its two 16-bit timer/counters generate precise PWM waveforms for three-phase inverter bridges, while the 10-bit ADC performs simultaneous current and back-EMF sampling for field-oriented control loops. At 16 MHz the core completes a full control-loop iteration in a few microseconds, fast enough for commutation at several thousand RPM. The 53 I/O lines can drive gate-driver enable signals, read Hall sensors, and monitor fault pins without external logic. The 4 KB SRAM holds lookup tables and filter state variables, and the 64 KB Flash accommodates sensorless control algorithms. Designers typically route PWM outputs to a dedicated gate driver and use the analog comparator for overcurrent shutdown, with the JTAG interface enabling real-time debug during tuning.
Рекомендуется
Legacy ATmega103 Board Upgrade
The ATMEGA64-16AU is the recommended upgrade for legacy ATmega103 designs because it is 100% pin compatible with the ATmega103 and can replace it on existing printed circuit boards without layout changes. The ATmega64 provides 64 KB Flash versus the ATmega103's 128 KB, but adds SRAM, EEPROM, dual USARTs, and a JTAG debug port that the older device lacks. By programming the M103C fuse, the ATmega64 enters ATmega103 compatibility mode, matching RAM, I/O pin functions, and interrupt vectors so existing firmware runs unmodified. This makes the ATMEGA64-16AU a low-risk path to extend the service life of industrial equipment whose original microcontroller has become obsolete or hard to source.
Рекомендуется
Battery-Powered Instrumentation
The ATMEGA64-16AU suits battery-powered instrumentation because it offers six sleep modes, including power-down and power-save, that reduce current draw to microamp levels between measurements. The 2 KB EEPROM stores logged data and calibration coefficients without an external memory device, and the real-time counter keeps time while the CPU sleeps. When active, the 16 MHz core and 10-bit ADC complete a measurement burst quickly and return to sleep, maximizing battery life. The 2.7 V to 5.5 V operating range at reduced clock speed allows direct operation from a lithium primary cell or a 3.3 V regulator. A typical design uses one USART for a wireless module and the other for a service port, with the 53 I/O lines handling keypad and display interfaces.
Рекомендуется
Multi-Interface Communication Gateway
The ATMEGA64-16AU works well as a communication gateway because its two independent USARTs can bridge two serial networks, such as RS-485 and RS-232, while the byte-oriented Two-wire serial interface connects to local sensor or EEPROM devices. The 64 KB Flash holds protocol stacks and buffering code, and the 4 KB SRAM provides enough space for dual receive/transmit ring buffers. At 16 MHz the device handles 115.2 kbps on both USARTs simultaneously with ample CPU headroom for protocol translation. The JTAG interface allows in-system debugging of the gateway firmware, and the 53 I/O lines can drive status LEDs, DIP switches, and hardware handshake signals. This makes the part a compact single-chip solution for protocol-conversion products.
Рекомендуется
Building Automation Node
The ATMEGA64-16AU is used in building automation nodes because it combines 53 I/O lines, dual USARTs, and an 8-channel 10-bit ADC in one device, allowing a single board to read temperature, humidity, and occupancy sensors while controlling HVAC actuators and lighting relays. The 64 KB Flash accommodates communication stacks such as Modbus or a proprietary fieldbus, and the 2 KB EEPROM retains node addresses and schedules through power failures. The -40 C to +85 C rating covers typical plenum and wall-mount environments. A common implementation uses one USART for the building network and the other for a local service interface, with the RTC providing time-stamped event logging. The JTAG port simplifies field firmware updates during commissioning.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATMEGA64-16AU — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATMEGA64-16AUR | ATMEGA64L-8AU | ATMEGA128-16AU | ATMEGA64A-AU |
|---|---|---|---|---|---|
| Package | 64-TQFP (14x14) | 64-TQFP (14x14) - same | 64-TQFP (14x14) - same | 64-TQFP (14x14) - same | 64-TQFP (14x14) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 64 KB | 64 KB | 128 KB | 64 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| EEPROM | 2 KB | 2 KB | 2 KB | 4 KB | 2 KB |
| Maximum CPU Speed | 16 MHz | 16 MHz | 8 MHz | 16 MHz | 16 MHz |
| Operating Voltage (at max speed) | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 2.7 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| General Purpose I/O Pins | 53 | 53 | 53 | 53 | 53 |
| Packaging | Tray | Tape & Reel | Tray | Tray | Tray |
| ATmega103 Pin Compatibility | Yes (100%) | Yes (100%) | Yes (100%) | Yes (100%) | Yes (100%) |
Ключевые отличия
- 100% pin compatibility with legacy ATmega103 (против ATMEGA644P-15AZ)
- Dual USARTs plus 53 I/O lines in one device (против ATMEGA32A-AU)
- Pin-compatible memory upgrade path (против ATMEGA128-16AU)
- Wide 2.7 V to 5.5 V operating range at reduced clock (против ATMEGA64L-8AU)
Заметки по проектированию
Decouple every VCC pin (pins 14 and 45) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, and add a 10 uF bulk capacitor near the regulator output. Filter AVCC (pin 57) through a ferrite bead or a 10 ohm resistor with a 100 nF capacitor to GND to isolate ADC noise from the digital supply. Connect AREF (pin 55) to a clean reference or to AVCC through a low-pass filter; never leave AREF floating, as this degrades ADC accuracy.
Route the crystal between XTAL1 (pin 17) and XTAL2 (pin 16) with the shortest possible traces and guard them with GND. Use load capacitors sized for the crystal's specified CL, typically 22 pF for a 16 MHz crystal with 8 pF load capacitance, and place them directly at the crystal pins. Keep the RESET pin (pin 13) trace short and add a 10 kohm pull-up plus a 100 nF capacitor to GND for reliable power-on reset. Avoid routing high-current switching traces beneath the MCU.
Do not exceed 16 MHz at 5 V or 8 MHz below 4.5 V; running the device outside its speed-voltage envelope causes unpredictable execution. When migrating firmware from an ATmega103, program the M103C fuse to enable compatibility mode, and remember that the ATmega64 has 4 KB SRAM versus the ATmega103's 4 KB but different I/O register mapping. Always set the correct fuse bits for the clock source before production, since an incorrect CKSEL setting can leave the device unable to enter the bootloader.
The JTAG port (TCK, TMS, TDI, TDO on pins 50, 49, 47, 48) shares pins with ADC channels 4 through 7. If you use those ADC inputs, disable the JTAG interface by programming the JTAGEN fuse to free the pins for analog use. Keep JTAG traces short and terminate TCK with a series resistor if the debug cable is long. For the two USARTs, add series termination resistors on long RS-485 runs and use a common-mode choke to reduce EMI.
Информация о соответствии
The ATMEGA64-16AU is described as GREEN and RoHS compliant in distributor and datasheet data. It is an industrial-grade device (-40 C to +85 C) and is not AEC-Q100 qualified; automotive designs require a separately qualified variant. REACH, halogen-free, and conflict-minerals status were not stated in the provided data.
