ATMEGA64A-MU - 8-Bit AVR MCU, 16MHz, 64KB Flash | Microchip
Артикул: ATMEGA64A-MU ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.62 | $6,62 |
| 10 | $5.96 | $59,60 |
| 100 | $5.3 | $530,00 |
| 500 | $4.75 | $2.375,00 |
| 1.000 | $4.24 | $4.240,00 |
ATMEGA64A-MU Обзор
An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most instructions in a single clock cycle, sitting at the low-power end of the power-management and embedded-control hierarchy. The ATmega family is widely used in industrial control, consumer appliances, and embedded systems where flash self-programmability and rich peripherals matter more than raw compute throughput.
Key features include 53 general-purpose I/O lines, 32 general-purpose working registers, four flexible timer/counters with compare modes, two USARTs, an 8-channel 10-bit ADC, a byte-oriented Two-Wire Interface (I2C-compatible), SPI, and a JTAG interface for on-chip debug and boundary scan. Read-while-write ISP Flash enables firmware updates in the field without halting code execution.
The AVR core combines a 131-instruction set with single-cycle execution, delivering up to 16 MIPS at 16 MHz. A real-time counter with separate oscillator supports RTC applications, while the enhanced power-save, ADC noise reduction, and standby idle modes let designers trade performance against microamp-level sleep currents. The ATmega64A is 100% pin compatible with the ATmega103 and can replace the ATmega103 on current printed circuit boards.
Typical applications include industrial automation controllers, HVAC and building-control nodes, battery-powered instrumentation, motor-control front ends, and embedded consumer devices requiring multiple communication interfaces.
Design consideration: at 16 MHz, keep decoupling capacitors close to the multiple VCC/GND pin pairs, and use the JTAG port for in-circuit debugging before disabling it as a general-purpose I/O.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для ATMEGA64A-MU — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATMEGA64A-MU (тот же форм-фактор и посадочное место) — отличается по Package, Debug Interface, Flash Memory, Timer/Counters, EEPROM.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATMEGA64-16MI
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.48 / шт.
Открыть даташит →ATMEGA128A-MUR
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$5.2 / шт.
Открыть даташит →AT90CAN64-16MU
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATMEGA649A-MU
✅ Прямая замена✓ В наличии
$4.42 / шт.
Открыть даташит →ATMEGA103-16MI
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATMEGA64A-MU Максимальные параметры и электрические характеристики
| Core Architecture | 8-bit AVR RISC |
| Max Clock Frequency | 16 MHz |
| Flash Memory | 64 KB (32K x 16) ISP, read-while-write |
| EEPROM | 2 KB |
| SRAM | 4 KB |
| General Purpose I/O | 53 lines |
| Working Registers | 32 |
| Timer/Counters | 4 (two 8-bit, two 16-bit) plus RTC |
| USART Interfaces | 2 |
| ADC | 8-channel 10-bit |
| TWI (I2C) | Yes, byte-oriented |
| SPI | Yes |
| JTAG Interface | Yes (on-chip debug and boundary scan) |
| Корпус | 64-QFN (9x9 mm), exposed pad, surface mount |
| Тип монтажа | Surface Mount |
| Pin Compatibility | 100% pin compatible with ATmega103 |
Конфигурация выводов ATMEGA64A-MU
| Контакт 1 | PE0 — Port E bit 0 / RXD0 / PDI |
| Контакт 2 | PE1 — Port E bit 1 / TXD0 / PDO |
| Контакт 3 | PE2 — Port E bit 2 / XCK0 / AIN0 |
| Контакт 4 | PE3 — Port E bit 3 / AIN1 / OC3A |
| Контакт 5 | PE4 — Port E bit 4 / OC3B / INT4 |
| Контакт 6 | PE5 — Port E bit 5 / OC3C / INT5 |
| Контакт 7 | PE6 — Port E bit 6 / T3 / INT6 |
| Контакт 8 | PE7 — Port E bit 7 / ICP3 / INT7 / CLKO |
| Контакт 9 | GND — Ground |
| Контакт 10 | AVCC — Analog supply for ADC |
| Контакт 11 | PG0 — Port G bit 0 / WR (external memory write strobe) |
| Контакт 12 | PG1 — Port G bit 1 / RD (external memory read strobe) |
| Контакт 13 | PC0 — Port C bit 0 / A8 (external memory address) |
| Контакт 14 | PC1 — Port C bit 1 / A9 |
| Контакт 15 | PC2 — Port C bit 2 / A10 |
| Контакт 16 | PC3 — Port C bit 3 / A11 |
| Контакт 17 | PC4 — Port C bit 4 / A12 |
| Контакт 18 | PC5 — Port C bit 5 / A13 |
| Контакт 19 | PC6 — Port C bit 6 / A14 |
| Контакт 20 | PC7 — Port C bit 7 / A15 |
| Контакт 21 | GND — Ground |
| Контакт 22 | AREF — Analog reference for ADC |
| Контакт 23 | PF0 — Port F bit 0 / ADC0 |
| Контакт 24 | PF1 — Port F bit 1 / ADC1 |
| Контакт 25 | PF2 — Port F bit 2 / ADC2 |
| Контакт 26 | PF3 — Port F bit 3 / ADC3 |
| Контакт 27 | PF4 — Port F bit 4 / ADC4 / TCK (JTAG) |
| Контакт 28 | PF5 — Port F bit 5 / ADC5 / TMS (JTAG) |
| Контакт 29 | PF6 — Port F bit 6 / ADC6 / TDO (JTAG) |
| Контакт 30 | PF7 — Port F bit 7 / ADC7 / TDI (JTAG) |
| Контакт 31 | PA0 — Port A bit 0 / AD0 (external memory bus) / GPIO |
| Контакт 32 | PA1 — Port A bit 1 / AD1 |
| Контакт 33 | PA2 — Port A bit 2 / AD2 |
| Контакт 34 | PA3 — Port A bit 3 / AD3 |
| Контакт 35 | PA4 — Port A bit 4 / AD4 |
| Контакт 36 | PA5 — Port A bit 5 / AD5 |
| Контакт 37 | PA6 — Port A bit 6 / AD6 |
| Контакт 38 | PA7 — Port A bit 7 / AD7 |
| Контакт 39 | PB0 — Port B bit 0 / SS (SPI slave select) / OC0 |
| Контакт 40 | PB1 — Port B bit 1 / SCK (SPI clock) |
| Контакт 41 | PB2 — Port B bit 2 / MOSI (SPI master out) |
| Контакт 42 | PB3 — Port B bit 3 / MISO (SPI master in) |
| Контакт 43 | PB4 — Port B bit 4 / OC2 (Timer2 output compare) |
| Контакт 44 | PB5 — Port B bit 5 / OC1A (Timer1 output compare A) |
| Контакт 45 | PB6 — Port B bit 6 / OC1B (Timer1 output compare B) |
| Контакт 46 | PB7 — Port B bit 7 / OC0A / OC1C |
| Контакт 47 | VCC — Digital supply voltage |
| Контакт 48 | GND — Ground |
| Контакт 49 | PD0 — Port D bit 0 / SCL (TWI clock) / INT0 |
| Контакт 50 | PD1 — Port D bit 1 / SDA (TWI data) / INT1 |
| Контакт 51 | PD2 — Port D bit 2 / TXD1 (USART1) / INT2 |
| Контакт 52 | PD3 — Port D bit 3 / RXD1 (USART1) / INT3 |
| Контакт 53 | PD4 — Port D bit 4 / ICP1 (Timer1 input capture) |
| Контакт 54 | PD5 — Port D bit 5 / XCK1 (USART1 clock) |
| Контакт 55 | PD6 — Port D bit 6 / T1 (Timer1 external clock) |
| Контакт 56 | PD7 — Port D bit 7 / T2 (Timer2 external clock) |
| Контакт 57 | PG2 — Port G bit 2 / ALE (external memory address latch enable) |
| Контакт 58 | PG3 — Port G bit 3 / TOSC2 (RTC oscillator output) |
| Контакт 59 | PG4 — Port G bit 4 / TOSC1 (RTC oscillator input) |
| Контакт 60 | RESET — Reset input (active low) |
| Контакт 61 | VCC — Digital supply voltage |
| Контакт 62 | GND — Ground |
| Контакт 63 | XTAL2 — Main crystal oscillator output |
| Контакт 64 | XTAL1 — Main crystal oscillator input / external clock |
Типичное применение
ATMEGA64A-MU подходит для 6 применениеs: Industrial Automation Controllers, HVAC and Building Control Nodes, Battery-Powered Instrumentation, Motor Control Front Ends, Embedded Consumer Devices, Legacy ATmega103 Board Redesign Avoidance.
Industrial Automation Controllers
The ATMEGA64A-MU fits industrial controller boards because its 64KB ISP Flash accommodates protocol stacks and state machines, its two USARTs drive RS-485 and a debug console simultaneously, and 53 GPIO lines interface relays, optocouplers, and limit switches directly. The 16 MHz single-cycle AVR core delivers deterministic interrupt latency for control loops up to the kilohertz range. Placed as the main MCU with a 5V rail and 100nF decoupling at each VCC pin, it reads encoders via timer capture and communicates over TWI or SPI to remote I/O expanders. Its JTAG port enables in-field debugging of deployed machinery controllers.
Рекомендуется
HVAC and Building Control Nodes
Building automation nodes benefit from the ATmega64A's real-time counter with the separate 32.768 kHz TOSC oscillator, enabling battery-backed timekeeping across power loss, while the 8-channel 10-bit ADC samples temperature, humidity, and pressure sensor chains. The 4KB SRAM holds multiple networked sensor buffers, and the two USARTs allow simultaneous RS-485 bus and service-port connectivity. Operating in power-save mode between acquisition cycles keeps standby current at microamp levels per the datasheet power tables, extending battery life in wireless-free, wall-thermostat-style deployments. The exposed-pad QFN improves heat dissipation in sealed enclosures.
Рекомендуется
Battery-Powered Instrumentation
Portable instruments leverage the ATMEGA64A-MU's power-down and power-save modes to stretch battery life while retaining the real-time counter for timestamping. The 10-bit ADC with internal reference digitizes bridge and thermistor inputs, and ADC noise reduction mode suppresses core clock noise during conversions, improving effective resolution at low sample rates. The 64KB Flash stores calibration tables and logging firmware, while 4KB SRAM buffers measurement records between UART or SPI uploads. With a 3V coin-cell or Li-ion rail through an LDO, the QFN's small 9x9 mm footprint suits handheld and panel-meter form factors.
Рекомендуется
Motor Control Front Ends
The ATmega64A's four timer/counters include two 16-bit units with input capture and three PWM compare channels per port B and E grouping, generating complementary or phase-correct PWM for DC and stepper motor drives. Input capture pins (ICP1, ICP3) timestamp quadrature or Hall sensor edges with 62.5 ns resolution at 16 MHz, enabling closed-loop speed control without external logic. The 10-bit ADC reads current-sense shunt amplifiers, and the fast AVR interrupt system handles overcurrent faults. External memory bus pins (ports A and C with ALE, WR, RD) allow expansion for larger trajectory tables via SRAM in servo applications.
Рекомендуется
Embedded Consumer Devices
Consumer appliances such as coffee machines, thermostats, and small printers use the ATMEGA64A-MU for its balance of Flash capacity and peripheral richness at a mainstream price. The byte-oriented TWI (I2C) manages touch controllers and EEPROM accessories, SPI drives display drivers and flash storage, and the dual USART supports factory test ports. Read-while-write ISP Flash allows field firmware updates through a bootloader without pausing output-critical timers. The 64-QFN with exposed pad solders reliably on standard reflow lines, and its 16 MHz core delivers responsive UI scan rates for keypads and rotary encoders in 5V or 3.3V designs.
Рекомендуется
Legacy ATmega103 Board Redesign Avoidance
Because Microchip documents the ATmega64A as 100% pin compatible with the ATmega103, the ATMEGA64A-MU is the standard migration path for boards designed around the obsolete ATmega103 in the 64-MLF/QFN footprint. The datasheet application note 'Replacing ATmega103 by ATmega64A' details register and peripheral differences. Designers gain doubled Flash (64KB), a second USART, more timers, and modern JTAG debugging without a PCB respin. This application is common in long-lifecycle industrial and medical equipment where recertification of a new board would be costly, making the drop-in swap the lowest-risk modernization route.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATMEGA64A-MU — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATMEGA64-16MI | ATMEGA128A-MU | AT90CAN64-16MU | ATMEGA649A-MU |
|---|---|---|---|---|---|
| Package | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN EP - same | 64-QFN - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 64 KB | 128 KB | 64 KB | 64 KB |
| Hardware CAN Controller | No | No | No | Yes (CAN 2.0A/B) | No |
| Segment LCD Controller | No | No | No | No | Yes |
| Core Compatibility | 100% pin compatible with ATmega103 | Same die family (pre-A revision) | Pin-compatible family lineage | AT90 CAN AVR family | ATmega649 family (LCD pin remap) |
Ключевые отличия
- Doubling of program memory in the same footprint (против ATMEGA128A-MU)
- Integrated hardware CAN controller (против AT90CAN64-16MU)
- Direct ATmega103 legacy replacement (против ATMEGA103-16MI)
Заметки по проектированию
The 64-QFN package exposes a large thermal pad on the underside that is internally connected to ground. Solder it to a ground copper pour with an array of thermal vias (typically 4x4 grid) to improve both heat dissipation and signal-ground integrity. Place 100nF ceramic decoupling capacitors within 2 mm of each VCC pin pair, plus one 4.7uF-10uF bulk capacitor near the supply entry. Connect AVCC to VCC through an LC filter (10uH ferrite bead plus 100nF) when ADC accuracy matters, and route AREF with its own decoupling capacitor.
JTAG is enabled by default from the factory on PORTF pins 4-7, disabling those ADC channels and GPIO. If your design uses ADC4-ADC7 or those port pins, disable JTAG via the JTD bit in MCUCSR (written twice within four cycles) or clear the JTAGEN fuse. Also note that RESET shares functions with PC6 in some AVR members - on ATmega64A RESET is a dedicated pin, but verify fuse settings (RSTDISBL must remain unprogrammed) before production programming, since programming it can permanently disable ISP entry.
For external memory bus operation (ALE, WR, RD with ports A and C), keep bus traces short and matched where possible, and latch AD0-AD7 with a 74x573 triggered by ALE. When running a 16 MHz crystal, place it within 5 mm of XTAL1/XTAL2 with grounded guard traces and use a crystal load capacitance per the crystal manufacturer's specification. The RTC TOSC 32.768 kHz circuit on PG3/PG4 is noise sensitive - isolate it from switching regulators and high-current PWM traces to avoid missed real-time ticks.
Информация о соответствии
Current-production Microchip part supplied in standard RoHS-compliant, lead-free packaging per distributor listings. REACH and halogen-free declarations should be confirmed on the Microchip product compliance page for the exact ordering code.
