Microchip Technology

ATTINY13A-SN - 8-Bit 20MHz AVR Microcontroller | Microchip

Артикул: ATTINY13A-SN ✓ Активен
1.8 V to 5.5 V Vdss 8-pin SOIC Package 20 MHz Speed 1 KB Memory
MOQ: 1 |

ATTINY13A-SN Обзор

Microchip Technology ATTINY13A-SN is a low-power 8-bit AVR RISC microcontroller with 1 KB of flash program memory, 64 bytes of EEPROM, 64 bytes of SRAM, and a maximum clock frequency of 20 MHz, housed in an 8-pin SOIC package. The device operates from 1.8 V to 5.5 V and delivers up to 20 MIPS throughput at 20 MHz.

An 8-bit microcontroller is a compact embedded-control device that combines a processor core, program memory, data memory, I/O ports, and peripherals on one semiconductor die. The ATtiny13A belongs to Microchip's tinyAVR family within the broader hierarchy of AVR embedded processors, 8-bit microcontrollers, and embedded systems. It is intended for control-intensive products where low cost, low power, and a small footprint matter more than instruction throughput or memory capacity.

The ATTINY13A-SN integrates four 10-bit ADC channels with an AVR processor that executes most instructions in a single clock cycle. Its 20 MHz maximum operating frequency supports throughput approaching 1 MIPS per MHz. Program storage is organized as 1 KB of flash, while 64 bytes of EEPROM retain data without power and 64 bytes of SRAM support working memory. These resources make the device suitable for compact sensors, simple control loops, configuration tools, and low-pin-count embedded accessories.

The 8-pin SOIC package exposes four I/O pins alongside power, ground, and reset. In-System Serial Programming and debug access can use the same reduced pin set used for the application. This is particularly useful for small production runs and prototypes because programming can be performed without removing the microcontroller from the circuit. The manufacturer product page identifies MPLAB Snap and a two-wire interface plus reset line as the supported debugging arrangement.

Typical uses include battery-powered sensors, simple motor controls, LED indicators, compact timers, and embedded teaching projects. Because the ATTINY13A has limited flash and SRAM, applications requiring substantial buffering, protocol stacks, or simultaneous complex control tasks should use a larger AVR or another microcontroller family. The ATtiny13A's strengths are its low component count, simple toolchain, and broad operating range in a standard surface-mount package.

When laying out a board, keep the decoupling capacitor close to VCC and GND, provide a clean reset path, and reserve the programming interface for ISP updates. Confirm the ADC reference and selected I/O pins against the design requirements. For new firmware, use the current AVR toolchain and verify timing, brown-out behavior, and unused-pin configuration in the final hardware.

This product page combines the manufacturer's electrical and architectural specifications with practical programming, PCB-layout, and replacement guidance. It also identifies genuine same-footprint options for engineers who need a different delivery format while preserving the ATTINY13A design.

Аналоги без доработки для ATTINY13A-SN — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с ATTINY13A-SN (тот же форм-фактор и посадочное место) — отличается по Package, Maximum Throughput.

Microchip Technology
Package: 8-SOIC
Сравнить с ATTINY13A-SN →
Microchip Technology
Maximum Throughput: 20 MIPS at 20 MHz
Сравнить с ATTINY13A-SN →

ATTINY13A-SU

✅ Прямая замена
Microchip Technology
📦 8-pin SOIC
8-bit AVR RISC-based microcontroller · 20 MHz · 1.8 V to 5.5 V · 1 KB · 512 x 16 bits · 64 bytes · 64 bytes · 32 bytes

Уточнить цену

Открыть даташит →

ATTINY13A-SH

✅ Прямая замена
Microchip Technology
📦 8-pin SOIC
AVR enhanced RISC · 8-bit microcontroller · 20 MHz · 1 KB · 512 x 16 bits · 64 bytes · 64 bytes · 6 ports

Уточнить цену

Открыть даташит →

ATTINY13A-SN Максимальные параметры и электрические характеристики

Product Type 8-bit RISC microcontroller
Architecture AVR enhanced RISC
Series tinyAVR
Максимальная тактовая частота 20 MHz
Maximum Throughput 20 MIPS
Program Flash Memory 1 KB
Flash Organization 512 x 16 bits
EEPROM 64 bytes
SRAM 64 bytes
Register File 32 bytes
Operating Voltage 1.8 V to 5.5 V
ADC Resolution 10 bits
ADC Channels 4 channels
Корпус 8-pin SOIC
Тип монтажа Surface mount
Programmable Memory Type ISP flash
Debug and Programming In-Circuit Serial Programming

Конфигурация выводов ATTINY13A-SN

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Контакт 1 PC0 — Port C input/output pin 0 with ADC input capability
Контакт 2 PC1 — Port C input/output pin 1 with ADC input capability
Контакт 3 PC2 — Port C input/output pin 2 with ADC input capability
Контакт 4 GND — Ground connection
Контакт 5 PB0 — Port B input/output pin 0
Контакт 6 PB1 — Port B input/output pin 1
Контакт 7 VCC — Supply voltage input
Контакт 8 RESET — Active-low reset input

Типичное применение

ATTINY13A-SN подходит для 6 применениеs: Battery-Powered Sensor Node, Simple LED Indicator Controller, Basic Motor Control, Industrial Configuration Interface, Portable Consumer Accessory, Embedded-Control Teaching Platform.

🧩

Battery-Powered Sensor Node

The ATTINY13A-SN fits a compact sensor node because its four-channel 10-bit ADC can sample analog inputs while the 1.8 V to 5.5 V operating range supports common low-energy rails. The device provides 64 bytes of EEPROM for persistent calibration values and 64 bytes of SRAM for short-lived working data. Use it as the supervisory controller for duty-cycled measurements, provided the complete firmware and buffering requirements fit the 1 KB program memory. Low-power operation should also account for sensor standby current, regulator quiescent current, and pull-network leakage rather than the microcontroller alone.

💡

Simple LED Indicator Controller

The ATTINY13A-SN can control several LED or logic-indicator outputs from its compact 8-pin SOIC footprint. Its 20 MHz AVR core provides substantially more timing margin than a simple switch controller, while the 1 KB flash area can hold compact state logic, debounce routines, and indicator patterns. The 64-byte SRAM is adequate for short status variables but not large display buffers. Drive LEDs through appropriately sized current-limiting resistors or a suitable driver, and confirm that the selected I/O pins have no analog-input or reset-function conflicts in the final schematic.

🏭

Basic Motor Control

The ATTINY13A-SN is suitable for small motor or actuator-control prototypes where a dedicated timer-heavy controller is unnecessary. Its 20 MHz operating speed supports faster control-loop execution, and the four ADC channels can monitor position or supply-related analog signals when the board layout permits. Because the device has only four general-purpose I/O pins and limited memory, use it for straightforward sequencing rather than elaborate motion algorithms. External transistor, flyback, and current-limiting circuitry remains required for inductive loads.

🔧

Industrial Configuration Interface

The ATTINY13A-SN can act as a small configuration or keypad-control device in industrial accessories. Its four I/O pins, reset function, and ISP support permit a compact implementation that can be programmed after assembly for product variants, calibration, or serial identification. The 1 KB flash and 64-byte EEPROM limit the complexity of menus, protocols, and stored records, so external serial memory is preferable for larger configurations. Design the programming interface to remain accessible without disturbing the product's normal operating mode.

📱

Portable Consumer Accessory

The ATTINY13A-SN is appropriate for a small portable accessory that combines a few inputs, one or more outputs, and simple embedded behavior. Its 1.8 V minimum operating voltage supports low-voltage designs, while 20 MHz execution provides responsive control without a large system-on-chip. The SOIC package supports conventional surface-mount assembly, although it occupies more board area than the smallest leadless packages. Verify startup behavior, brown-out tolerance, and power consumption across the complete battery-discharge range before using it as the sole system controller.

🖥️

Embedded-Control Teaching Platform

The ATTINY13A-SN provides a manageable platform for learning AVR assembly, C firmware, GPIO use, and ADC interfacing. Its 1 KB flash makes code-size discipline visible, while the 20 MHz clock allows instruction-level timing experiments without a complex development board. The four-channel 10-bit ADC supports basic signal measurement, and the documented ISP workflow enables repeatable programming. For larger projects, document memory use early and migrate to a higher-capacity microcontroller rather than adding unmanaged libraries to the 64-byte SRAM environment.

What are the key specifications of ATTINY13A-SN that engineers should know?
The ATTINY13A-SN is an 8-bit AVR microcontroller with 1 KB of flash, 64 bytes of EEPROM, 64 bytes of SRAM, and a maximum clock speed of 20 MHz. According to the Microchip ATtiny13A data sheet, the device operates from 1.8 V to 5.5 V, includes a four-channel 10-bit ADC, and can reach 20 MIPS throughput. It is packaged in an 8-pin SOIC, making it suitable for compact embedded-control and sensing products.
Where can I download the ATTINY13A-SN datasheet PDF?
The official ATTINY13A-SN datasheet PDF is available from Microchip Technology through the ATtiny13A data sheet document DS40002307A. The document contains the device architecture, electrical characteristics, memory organization, pin descriptions, ADC information, and programming details. Engineers should use the manufacturer document as the controlling reference for operating limits, timing, and package drawings.
Where is the ATTINY13A-SN pinout located?
The ATTINY13A-SN pinout is shown in the Microchip ATtiny13A data sheet, including the pin-description and package diagrams. The device uses an 8-pin SOIC with power, ground, reset, and four general-purpose I/O connections. Assign board tracks from the pin-description table and preserve the orientation of the package pin-1 marker. The same document also identifies the analog input functions associated with the I/O pins.
How do I program ATTINY13A-SN with Arduino?
The ATTINY13A-SN can be programmed through the Arduino ecosystem using an ATtiny13A-compatible hardware package and an ISP-capable programmer. The ATtiny13A data sheet confirms support for In-Circuit Serial Programming, allowing firmware to be written while the device remains mounted on the target board. Configure the selected ATtiny13A board definition, connect the ISP interface correctly, and select the matching device and clock settings before uploading firmware.
What can replace ATTINY13A-SN?
The closest drop-in choices identified for ATTINY13A-SN are ATTINY13A-SU and ATTINY13A-SH, both of which retain the same 8-pin SOIC footprint and ATTINY13A electrical configuration. Their differences concern ordering or delivery format rather than the processor, memory, ADC, or clock architecture. Confirm the exact pinout, package drawing, and programming requirements before replacing the -SN order code.
Is ATTINY13A-SN the same as ATTINY13A-SU?
The ATTINY13A-SN and ATTINY13A-SU are based on the same ATtiny13A device and share the 8-pin SOIC package. The comparison identifies the same AVR 8-bit core, 20 MHz speed, active product status, and core peripherals, while the ordering suffix differs. For a drop-in PCB substitution, verify the manufacturer package drawing, pin orientation, supply requirements, and intended packing method before releasing production parts.
ATTINY13A-SN vs ATTINY85: which microcontroller should I choose?
Choose the ATTINY13A-SN for a compact control design that needs only 1 KB of flash, 64 bytes of EEPROM, 64 bytes of SRAM, four 10-bit ADC channels, and a small number of I/O pins. Choose an ATTINY85 when the application requires more program and data memory or additional I/O resources. The ATtiny13A-SN is therefore attractive for simple standalone controllers, while the larger device is better suited to more complex sensing and communication roles.
When should I choose ATTINY13A-SN over ATTINY13A-SU?
Choose ATTINY13A-SN when its specified delivery configuration matches your assembly process and you need an 8-pin SOIC device with 20 MHz operation. Choose ATTINY13A-SU when its available delivery configuration better supports production handling while preserving the same ATtiny13A core, memory, ADC, voltage range, and package footprint. The decisive factor is procurement and assembly packaging rather than a change in electrical performance.
Is ATTINY13A-SN suitable for battery-powered sensor applications?
The ATTINY13A-SN is suitable for small battery-powered sensor products when its 1.8 V to 5.5 V operating range and four-channel 10-bit ADC meet the sensing requirements. Its tinyAVR architecture supports compact embedded-control functions without requiring a large processor. For low-duty-cycle operation, use the device's power-saving modes and evaluate the complete sleep-period current of the sensor, regulator, pull resistors, and communication hardware.
How much memory does ATTINY13A-SN have?
The ATTINY13A-SN provides 1 KB of flash program memory, organized as 512 x 16 bits, together with 64 bytes of EEPROM and 64 bytes of SRAM. According to the Microchip ATtiny13A data sheet, the device also includes a 32-byte register file. This memory footprint is sufficient for compact control firmware but requires careful code-size planning for protocols, libraries, and buffer management.
What is the operating voltage of ATTINY13A-SN?
The ATTINY13A-SN operates from 1.8 V to 5.5 V. The Microchip manufacturer product page identifies this range for the ATtiny13A family, while the data sheet provides detailed operating conditions, ADC characteristics, and clock requirements. A design intended for 3.3 V or 5 V operation therefore fits the device's range, but external components and the selected programming tool must also support the target supply voltage.
How do I choose an ISP debugger for ATTINY13A-SN?
Select an ISP debugger that supports the ATtiny13A device and its clock configuration. Microchip's ATtiny13A product page identifies MPLAB Snap as a supported debug tool connected through a high-speed USB interface and an 8-pin single-inline connector. That interface uses two I/O lines and the reset line for In-Circuit Serial Programming, allowing programming and debugging without removing the device from its circuit.
Is ATTINY13A-SN RoHS compliant?
The RoHS status of ATTINY13A-SN is not explicitly stated in the cited product excerpts, so it should be confirmed with Microchip's current product documentation before certification is assigned. RoHS compliance is normally assessed using the current EU definition of restricted substances and the exact finished-part configuration. Use the manufacturer declaration or material compliance record associated with the ordered MPN and package form.
What is the lead time and stock status of ATTINY13A-SN?
Current stock, lead time, and minimum order quantity for ATTINY13A-SN should be requested through the Request a Quote form on this page. The manufacturer identifies the ATtiny13A family as active, but production schedules and component availability can change independently of lifecycle status. Provide the target quantity, delivery format, and required destination when requesting the quotation.
Where can I buy ATTINY13A-SN and check its price?
Use the Request a Quote form on this page to request the current price, stock, lead time, and minimum order quantity for ATTINY13A-SN. Microchip identifies the ATtiny13A as an active product, and the ATTINY13A-SN is offered in an 8-pin SOIC configuration. The quotation request should identify whether the delivery format must match the -SN order code or whether another documented drop-in suffix is acceptable.
Is there a Microchip equivalent for ATTINY13A-SN?
Microchip Technology provides ATTINY13A-SU and ATTINY13A-SH as same-family drop-in candidates for the ATTINY13A-SN in the 8-pin SOIC footprint. Both retain the ATtiny13A's 8-bit AVR core, 20 MHz maximum clock, 1 KB flash, 64-byte EEPROM, 64-byte SRAM, and four-channel 10-bit ADC configuration. Validate the selected part's package drawing, pin arrangement, qualification requirements, and assembly format before substitution.

Справочные инженерные данные для ATTINY13A-SN — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the ATTINY13A-SN when the design needs a low-cost, low-power AVR controller with 1 KB of flash, 64 bytes of EEPROM, 64 bytes of SRAM, four 10-bit ADC channels, and an 8-pin SOIC footprint. Select ATTINY13A-SU or ATTINY13A-SH when those same-family order codes offer a more suitable delivery configuration; the verified comparison indicates the same core, speed, memory, ADC, package, and active status. These alternatives are appropriate when only procurement or assembly format changes. Do not select a different ATtiny family solely by matching the eight-pin package: check the complete pin table, ADC assignments, reset circuit, and programming interface. If the firmware requires more memory, more I/O, larger buffers, or a communication stack beyond the ATTINY13A's resources, choose a higher-capacity MCU instead of forcing the design into 1 KB of program memory.

Сравнение с аналогами

Параметр Этот товар ATTINY13A-SU ATTINY13A-SH
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand Microchip Technology Microchip Technology Microchip Technology
Core Processor 8-bit AVR 8-bit AVR 8-bit AVR
Maximum Clock Frequency 20 MHz 20 MHz 20 MHz
Flash Memory 1 KB 1 KB 1 KB
EEPROM 64 bytes 64 bytes 64 bytes
SRAM 64 bytes 64 bytes 64 bytes
ADC 4 channels, 10-bit 4 channels, 10-bit 4 channels, 10-bit
Operating Voltage 1.8 V to 5.5 V 1.8 V to 5.5 V 1.8 V to 5.5 V

Ключевые отличия

  • Very small programmable control platform (против ATTINY13A-SU)
  • Pin-compatible same-family sourcing option (против ATTINY13A-SH)
  • Sufficient throughput for compact embedded-control loops (против ATTINY13A-SU)

Заметки по проектированию

Place the supply decoupling capacitor immediately between the VCC and GND pins, with a short, low-loop-area connection to the device. Keep the ISP programming contacts accessible and route them away from sensitive analog inputs. Because the 8-pin SOIC leaves little space for external circuitry, reserve the footprint on a generous pad pitch and confirm the package drawing against the selected manufacturer's order code.

Do not design around the assumption that another small AVR is pin-compatible. The ATTINY13A-SN, ATTINY13A-SU, and ATTINY13A-SH options share the ATtiny13A family configuration and 8-pin SOIC footprint, whereas larger ATtiny devices can use different SOIC pin assignments despite having the same pin count. Check the exact data-sheet pin table, ADC channels, reset behavior, and power pins before approving a substitution.

Keep firmware, timing, and serial interfaces within the device's 1 KB flash and 64-byte SRAM limits. Use the 20 MHz maximum clock only when the operating voltage and application timing support it. For battery designs, measure average and sleep current with peripheral loads connected because ADC references, pull resistors, indicator drivers, and regulator leakage can dominate the power budget.

Reserve unused input pins for a defined state and review their analog-input assignment in the final pin plan. The four ADC inputs are multiplexed with I/O functions, so a board that routes a sensitive sensor to one of those pins must account for leakage, source impedance, and sampling time. Maintain a short return path to the device ground and use a quiet reference arrangement when measurements require repeatable results.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The cited manufacturer and distributor excerpts do not explicitly state the requested compliance declarations. The AEC-Q100 field is marked not applicable because the ATTINY13A-SN is presented as a general-purpose 8-bit microcontroller rather than an automotive-qualified variant.

Данные проверены: 2026-11-09 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

attiny13a pinout attiny13a datasheet attiny13a price attiny13a programming attiny13a vs attiny85 attiny13a programming with arduino attiny13 projects attiny13a smd attiny13a datasheet pdf ATTINY13A-SN datasheet ATTINY13A-SN pinout ATTINY13A-SN equivalent ATTINY13A-SN replacement Microchip ATTINY13A-SN ATTINY13A-SN 8-pin SOIC

Связанные компоненты & термины

Microchip Technology ATTINY13A-SN ATTINY13A-SU ATTINY13A-SH ATtiny13A ATtiny85 AVR tinyAVR 8-bit microcontroller RISC architecture embedded processor embedded system 1 KB flash 64-byte EEPROM 64-byte SRAM 20 MHz 20 MIPS 10-bit ADC In-Circuit Serial Programming ISP MPLAB Snap 8-pin SOIC surface mount picoPower
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ