ATTINY13A-SN - 8-Bit 20MHz AVR Microcontroller | Microchip
MPN: ATTINY13A-SN ✓ AktifATTINY13A-SN Genel Bakış
An 8-bit microcontroller is a compact embedded-control device that combines a processor core, program memory, data memory, I/O ports, and peripherals on one semiconductor die. The ATtiny13A belongs to Microchip's tinyAVR family within the broader hierarchy of AVR embedded processors, 8-bit microcontrollers, and embedded systems. It is intended for control-intensive products where low cost, low power, and a small footprint matter more than instruction throughput or memory capacity.
The ATTINY13A-SN integrates four 10-bit ADC channels with an AVR processor that executes most instructions in a single clock cycle. Its 20 MHz maximum operating frequency supports throughput approaching 1 MIPS per MHz. Program storage is organized as 1 KB of flash, while 64 bytes of EEPROM retain data without power and 64 bytes of SRAM support working memory. These resources make the device suitable for compact sensors, simple control loops, configuration tools, and low-pin-count embedded accessories.
The 8-pin SOIC package exposes four I/O pins alongside power, ground, and reset. In-System Serial Programming and debug access can use the same reduced pin set used for the application. This is particularly useful for small production runs and prototypes because programming can be performed without removing the microcontroller from the circuit. The manufacturer product page identifies MPLAB Snap and a two-wire interface plus reset line as the supported debugging arrangement.
Typical uses include battery-powered sensors, simple motor controls, LED indicators, compact timers, and embedded teaching projects. Because the ATTINY13A has limited flash and SRAM, applications requiring substantial buffering, protocol stacks, or simultaneous complex control tasks should use a larger AVR or another microcontroller family. The ATtiny13A's strengths are its low component count, simple toolchain, and broad operating range in a standard surface-mount package.
When laying out a board, keep the decoupling capacitor close to VCC and GND, provide a clean reset path, and reserve the programming interface for ISP updates. Confirm the ADC reference and selected I/O pins against the design requirements. For new firmware, use the current AVR toolchain and verify timing, brown-out behavior, and unused-pin configuration in the final hardware.
This product page combines the manufacturer's electrical and architectural specifications with practical programming, PCB-layout, and replacement guidance. It also identifies genuine same-footprint options for engineers who need a different delivery format while preserving the ATTINY13A design.
Drop-in alternatifler için ATTINY13A-SN — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller ATTINY13A-SN (aynı form faktörü ve ayağa oturma) — farklı olan Package, Maximum Throughput.
ATTINY13A-SU
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →ATTINY13A-SH
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →ATTINY13A-SN Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Type | 8-bit RISC microcontroller |
| Architecture | AVR enhanced RISC |
| Series | tinyAVR |
| Azami Saat Hızı | 20 MHz |
| Maximum Throughput | 20 MIPS |
| Program Flash Memory | 1 KB |
| Flash Organization | 512 x 16 bits |
| EEPROM | 64 bytes |
| SRAM | 64 bytes |
| Register File | 32 bytes |
| Operating Voltage | 1.8 V to 5.5 V |
| ADC Resolution | 10 bits |
| ADC Channels | 4 channels |
| Paket | 8-pin SOIC |
| Montaj Türü | Surface mount |
| Programmable Memory Type | ISP flash |
| Debug and Programming | In-Circuit Serial Programming |
ATTINY13A-SN Pin Yapısı
| Pin 1 | PC0 — Port C input/output pin 0 with ADC input capability |
| Pin 2 | PC1 — Port C input/output pin 1 with ADC input capability |
| Pin 3 | PC2 — Port C input/output pin 2 with ADC input capability |
| Pin 4 | GND — Ground connection |
| Pin 5 | PB0 — Port B input/output pin 0 |
| Pin 6 | PB1 — Port B input/output pin 1 |
| Pin 7 | VCC — Supply voltage input |
| Pin 8 | RESET — Active-low reset input |
Tipik Uygulamalar
ATTINY13A-SN için uygundur 6 uygulamas: Battery-Powered Sensor Node, Simple LED Indicator Controller, Basic Motor Control, Industrial Configuration Interface, Portable Consumer Accessory, Embedded-Control Teaching Platform.
Battery-Powered Sensor Node
The ATTINY13A-SN fits a compact sensor node because its four-channel 10-bit ADC can sample analog inputs while the 1.8 V to 5.5 V operating range supports common low-energy rails. The device provides 64 bytes of EEPROM for persistent calibration values and 64 bytes of SRAM for short-lived working data. Use it as the supervisory controller for duty-cycled measurements, provided the complete firmware and buffering requirements fit the 1 KB program memory. Low-power operation should also account for sensor standby current, regulator quiescent current, and pull-network leakage rather than the microcontroller alone.
Önerilen
Simple LED Indicator Controller
The ATTINY13A-SN can control several LED or logic-indicator outputs from its compact 8-pin SOIC footprint. Its 20 MHz AVR core provides substantially more timing margin than a simple switch controller, while the 1 KB flash area can hold compact state logic, debounce routines, and indicator patterns. The 64-byte SRAM is adequate for short status variables but not large display buffers. Drive LEDs through appropriately sized current-limiting resistors or a suitable driver, and confirm that the selected I/O pins have no analog-input or reset-function conflicts in the final schematic.
Önerilen
Basic Motor Control
The ATTINY13A-SN is suitable for small motor or actuator-control prototypes where a dedicated timer-heavy controller is unnecessary. Its 20 MHz operating speed supports faster control-loop execution, and the four ADC channels can monitor position or supply-related analog signals when the board layout permits. Because the device has only four general-purpose I/O pins and limited memory, use it for straightforward sequencing rather than elaborate motion algorithms. External transistor, flyback, and current-limiting circuitry remains required for inductive loads.
Önerilen
Industrial Configuration Interface
The ATTINY13A-SN can act as a small configuration or keypad-control device in industrial accessories. Its four I/O pins, reset function, and ISP support permit a compact implementation that can be programmed after assembly for product variants, calibration, or serial identification. The 1 KB flash and 64-byte EEPROM limit the complexity of menus, protocols, and stored records, so external serial memory is preferable for larger configurations. Design the programming interface to remain accessible without disturbing the product's normal operating mode.
Önerilen
Portable Consumer Accessory
The ATTINY13A-SN is appropriate for a small portable accessory that combines a few inputs, one or more outputs, and simple embedded behavior. Its 1.8 V minimum operating voltage supports low-voltage designs, while 20 MHz execution provides responsive control without a large system-on-chip. The SOIC package supports conventional surface-mount assembly, although it occupies more board area than the smallest leadless packages. Verify startup behavior, brown-out tolerance, and power consumption across the complete battery-discharge range before using it as the sole system controller.
Önerilen
Embedded-Control Teaching Platform
The ATTINY13A-SN provides a manageable platform for learning AVR assembly, C firmware, GPIO use, and ADC interfacing. Its 1 KB flash makes code-size discipline visible, while the 20 MHz clock allows instruction-level timing experiments without a complex development board. The four-channel 10-bit ADC supports basic signal measurement, and the documented ISP workflow enables repeatable programming. For larger projects, document memory use early and migrate to a higher-capacity microcontroller rather than adding unmanaged libraries to the 64-byte SRAM environment.
Önerilen
Mühendislik referans verileri: ATTINY13A-SN — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | ATTINY13A-SU | ATTINY13A-SH |
|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Processor | 8-bit AVR | 8-bit AVR | 8-bit AVR |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz |
| Flash Memory | 1 KB | 1 KB | 1 KB |
| EEPROM | 64 bytes | 64 bytes | 64 bytes |
| SRAM | 64 bytes | 64 bytes | 64 bytes |
| ADC | 4 channels, 10-bit | 4 channels, 10-bit | 4 channels, 10-bit |
| Operating Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
Ana Farklılayıcılar
- Very small programmable control platform (karşılaştırma:ATTINY13A-SU)
- Pin-compatible same-family sourcing option (karşılaştırma:ATTINY13A-SH)
- Sufficient throughput for compact embedded-control loops (karşılaştırma:ATTINY13A-SU)
Tasarım Notları
Place the supply decoupling capacitor immediately between the VCC and GND pins, with a short, low-loop-area connection to the device. Keep the ISP programming contacts accessible and route them away from sensitive analog inputs. Because the 8-pin SOIC leaves little space for external circuitry, reserve the footprint on a generous pad pitch and confirm the package drawing against the selected manufacturer's order code.
Do not design around the assumption that another small AVR is pin-compatible. The ATTINY13A-SN, ATTINY13A-SU, and ATTINY13A-SH options share the ATtiny13A family configuration and 8-pin SOIC footprint, whereas larger ATtiny devices can use different SOIC pin assignments despite having the same pin count. Check the exact data-sheet pin table, ADC channels, reset behavior, and power pins before approving a substitution.
Keep firmware, timing, and serial interfaces within the device's 1 KB flash and 64-byte SRAM limits. Use the 20 MHz maximum clock only when the operating voltage and application timing support it. For battery designs, measure average and sleep current with peripheral loads connected because ADC references, pull resistors, indicator drivers, and regulator leakage can dominate the power budget.
Reserve unused input pins for a defined state and review their analog-input assignment in the final pin plan. The four ADC inputs are multiplexed with I/O functions, so a board that routes a sensitive sensor to one of those pins must account for leakage, source impedance, and sampling time. Maintain a short return path to the device ground and use a quiet reference arrangement when measurements require repeatable results.
Uyumluluk Bilgisi
The cited manufacturer and distributor excerpts do not explicitly state the requested compliance declarations. The AEC-Q100 field is marked not applicable because the ATTINY13A-SN is presented as a general-purpose 8-bit microcontroller rather than an automotive-qualified variant.