ATXMEGA256A3U-AU - 256KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip
Артикул: ATXMEGA256A3U-AU ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $14.5 | $14,50 |
| 10 | $12.95 | $129,50 |
| 100 | $11.4 | $1.140,00 |
| 500 | $10.2 | $5.100,00 |
| 1.000 | $9.1 | $9.100,00 |
ATXMEGA256A3U-AU Обзор
An 8/16-bit microcontroller (MCU) is a programmable system-on-a-chip that combines a CPU, Flash program memory, SRAM, EEPROM, and a rich set of peripherals on a single die. MCUs are the highest-volume category of integrated circuits and serve as the digital core of nearly every embedded product - from battery-powered IoT nodes to industrial motor drives - occupying the middle of the silicon hierarchy between simple discrete logic and full microprocessors.
Key features include 16 KB SRAM, 4 KB EEPROM, a 4-channel DMA controller, an 8-channel event system, and 34 programmable I/O lines. The device operates from a 2.7V to 3.6V supply, supports LVTTL/LVCMOS-compatible I/O, and includes multiple communication interfaces (USART, SPI, TWI) plus a 12-channel 12-bit ADC and analog comparators. The A3U variant adds a USB 2.0 Full-Speed device interface absent from the non-U A3 series.
The ATXMEGA256A3U uses a Harvard-architecture AVR CPU with a 3-stage pipeline and hardware multiplier, achieving 1 MIPS per MHz. The peripheral event system lets peripherals trigger one another without CPU intervention, freeing the core for application code. The 4-channel DMA controller can move data between peripherals and memory autonomously, further reducing CPU load for streaming or signal-processing tasks.
Typical applications include building automation, industrial control, low-power IoT sensor nodes, motor control, metering, USB peripherals, and human-machine interfaces (HMI) with LCD segments. The wide peripheral set and large Flash make it well suited to data logging, LCD-keypad control panels, and protocol bridges that previously required external logic.
When designing with this MCU, allocate adequate decoupling (typically 100 nF plus 10 uF bulk) close to each VCC pin, and follow the XMEGA AU manual guidance for PDI programming interface routing. The 64-pin TQFP footprint is shared with the rest of the ATxmega A3U family, allowing easy migration to the 192A3U, 128A3U, or 64A3U derivatives by code recompilation.
Аналоги без доработки для ATXMEGA256A3U-AU — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATXMEGA256A3U-AU (тот же форм-фактор и посадочное место) — отличается по Operating Temperature, Program Memory (Flash), RoHS Status, USB Interface.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATXMEGA256A3U-AUR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATXMEGA192A3U-AU
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATXMEGA128A3U-AU
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATXMEGA64A3U-AU
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATXMEGA256A3U-ANR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATXMEGA256A3U-AU Максимальные параметры и электрические характеристики
| Core Architecture | AVR enhanced RISC (8/16-bit) |
| Family | AVR XMEGA A3U |
| Program Memory (Flash) | 256 KB (128K x 16) |
| Boot Code Section | 8 KB |
| SRAM | 16 KB |
| EEPROM | 4 KB |
| Maximum CPU Speed | 32 MHz (32 MIPS) |
| Supply Voltage (VCC) | 2.7 V to 3.6 V |
| I/O Pins | 34 programmable I/O lines |
| DMA Channels | 4 |
| Event System Channels | 8 |
| USB Interface | USB 2.0 Full-Speed Device (A3U variant) |
| Корпус | 64-pin TQFP (14x14 mm) |
| Рабочая температура | -40C to +85C (industrial) |
| Programming Interface | PDI (Program and Debug Interface) |
| Статус RoHS | Compliant |
| Тип монтажа | Surface Mount |
Конфигурация выводов ATXMEGA256A3U-AU
| Контакт 1 | VCC — Digital supply voltage (2.7-3.6 V) |
| Контакт 2 | PA0 — PORTA bit 0, analog input, peripheral function |
| Контакт 3 | PA1 — PORTA bit 1, analog input, peripheral function |
| Контакт 4 | PA2 — PORTA bit 2, analog input, peripheral function |
| Контакт 5 | PA3 — PORTA bit 3, analog input, peripheral function |
| Контакт 6 | PA4 — PORTA bit 4, analog input, peripheral function |
| Контакт 7 | PA5 — PORTA bit 5, analog input, peripheral function |
| Контакт 8 | PA6 — PORTA bit 6, analog input, peripheral function |
| Контакт 9 | PA7 — PORTA bit 7, analog input, peripheral function |
| Контакт 10 | GND — Ground |
| Контакт 11 | PB0 — PORTB bit 0, peripheral function |
| Контакт 12 | PB1 — PORTB bit 1, peripheral function |
| Контакт 13 | PB2 — PORTB bit 2, peripheral function |
| Контакт 14 | PB3 — PORTB bit 3, peripheral function |
| Контакт 15 | PB4 — PORTB bit 4, peripheral function |
| Контакт 16 | PB5 — PORTB bit 5, peripheral function |
| Контакт 17 | PB6 — PORTB bit 6, peripheral function |
| Контакт 18 | PB7 — PORTB bit 7, peripheral function |
| Контакт 19 | GND — Ground |
| Контакт 20 | VCC — Digital supply voltage |
| Контакт 21 | PC0 — PORTC bit 0, peripheral function |
| Контакт 22 | PC1 — PORTC bit 1, peripheral function |
| Контакт 23 | PC2 — PORTC bit 2, peripheral function |
| Контакт 24 | PC3 — PORTC bit 3, peripheral function |
| Контакт 25 | PC4 — PORTC bit 4, peripheral function |
| Контакт 26 | PC5 — PORTC bit 5, peripheral function |
| Контакт 27 | PC6 — PORTC bit 6, peripheral function |
| Контакт 28 | PC7 — PORTC bit 7, peripheral function |
| Контакт 29 | GND — Ground |
| Контакт 30 | VCC — Digital supply voltage |
| Контакт 31 | PD0 — PORTD bit 0, peripheral function |
| Контакт 32 | PD1 — PORTD bit 1, peripheral function |
| Контакт 33 | PD2 — PORTD bit 2, peripheral function |
| Контакт 34 | PD3 — PORTD bit 3, peripheral function |
| Контакт 35 | PD4 — PORTD bit 4, peripheral function |
| Контакт 36 | PD5 — PORTD bit 5, peripheral function |
| Контакт 37 | PD6 — PORTD bit 6, peripheral function |
| Контакт 38 | PD7 — PORTD bit 7, peripheral function |
| Контакт 39 | GND — Ground |
| Контакт 40 | VCC — Digital supply voltage |
| Контакт 41 | PE0 — PORTE bit 0, peripheral function |
| Контакт 42 | PE1 — PORTE bit 1, peripheral function |
| Контакт 43 | PE2 — PORTE bit 2, peripheral function |
| Контакт 44 | PE3 — PORTE bit 3, peripheral function |
| Контакт 45 | PE4 — PORTE bit 4, peripheral function |
| Контакт 46 | PE5 — PORTE bit 5, peripheral function |
| Контакт 47 | PE6 — PORTE bit 6, TOSC2, peripheral function |
| Контакт 48 | PE7 — PORTE bit 7, TOSC1, peripheral function |
| Контакт 49 | GND — Ground |
| Контакт 50 | VCC — Digital supply voltage |
| Контакт 51 | PF0 — PORTF bit 0, analog input, peripheral function |
| Контакт 52 | PF1 — PORTF bit 1, analog input, peripheral function |
| Контакт 53 | PF2 — PORTF bit 2, analog input, peripheral function (USB D-) |
| Контакт 54 | PF3 — PORTF bit 3, analog input, peripheral function (USB D+) |
| Контакт 55 | PF4 — PORTF bit 4, analog input, peripheral function |
| Контакт 56 | PF5 — PORTF bit 5, analog input, peripheral function |
| Контакт 57 | PF6 — PORTF bit 6, analog input, peripheral function |
| Контакт 58 | PF7 — PORTF bit 7, analog input, peripheral function |
| Контакт 59 | GND — Ground |
| Контакт 60 | AVCC — Analog supply voltage |
| Контакт 61 | PDI_DATA — Program and Debug Interface data |
| Контакт 62 | PDI_CLOCK — Program and Debug Interface clock |
| Контакт 63 | RESET — Reset input, active low |
| Контакт 64 | VCC — Digital supply voltage |
Типичное применение
ATXMEGA256A3U-AU подходит для 6 применениеs: USB Human Interface Devices (HID), Building Automation Controllers, Industrial Motor Control, Smart Metering and Data Logging, LCD HMI Control Panels, IoT Sensor Hubs and Protocol Bridges.
USB Human Interface Devices (HID)
The ATXMEGA256A3U-AU is purpose-built for USB HID peripherals thanks to its integrated USB 2.0 Full-Speed device controller, which eliminates the need for an external USB PHY or bridge chip. The 32 MHz core and 32 MIPS throughput comfortably drive USB stacks alongside HID report processing at 1 kHz polling rates, while the 256 KB Flash holds USB class drivers, descriptor tables, and application firmware. The 16 KB SRAM buffers HID reports without CPU intervention thanks to the 4-channel DMA controller, and the 8-channel event system lets the USB and timer peripherals trigger one another autonomously. Place a 22-ohm source termination on D+/D- and follow the datasheet's recommended USB section layout (common-mode choke near the connector) for reliable EMI performance.
Рекомендуется
Building Automation Controllers
Building automation systems need 256 KB of Flash to host BACnet, KNX, or Modbus stacks plus application logic for HVAC, lighting, and access control. The ATXMEGA256A3U-AU's 34 programmable I/O lines drive relays, triacs, and 0-10V analog outputs, while the 12-bit ADC reads temperature, humidity, and occupancy sensors with 12-bit precision. The wide 2.7-3.6V supply tolerates 24V-bus-derived rails after regulation, and the XMEGA event system triggers ADC conversions from timers without CPU load. Compared to a discrete 8051 solution, the A3U delivers 2-3x more code density per MHz and runs at 1/3 the active current.
Рекомендуется
Industrial Motor Control
Three-phase BLDC and PMSM motor control demands high-resolution PWM, fast ADC sampling synchronized to the PWM timer, and deterministic interrupt response - all native to the ATXMEGA256A3U-AU. The 32 MHz core executes field-oriented control loops at 16 kHz with margin to spare, while the event system routes timer compare outputs directly to ADC triggers for jitter-free current sensing. The 4-channel DMA offloads commutation-table updates from the CPU, and 16 KB SRAM holds two complete control frames. Operating temperature of -40C to +85C suits industrial enclosures, and the 64-pin TQFP footprint provides ample ground and power pins for thermal dissipation at switching frequencies above 20 kHz.
Рекомендуется
Smart Metering and Data Logging
Electricity, water, and gas meters need low sleep current, robust Flash endurance for frequent parameter writes, and large storage for interval data. The ATXMEGA256A3U-AU provides 4 KB EEPROM with 100k+ write cycles for tariff and calibration data, 256 KB Flash for logging firmware, and the XMEGA sleep modes draw microamp-level current between measurement intervals. The 12-bit ADC with differential inputs directly samples shunt resistors for Class 1 metering accuracy, and the 8-channel event system schedules ADC, RTC, and UART wake-ups with zero CPU overhead. Real-time clock functionality through the 32.768 kHz TOSC oscillator enables accurate interval timing without external RTC chips.
Рекомендуется
LCD HMI Control Panels
Industrial HMI panels with segmented LCDs, keypads, and buzzer feedback fit naturally on the ATXMEGA256A3U-AU thanks to the integrated LCD controller that supports up to 40 segments without external drivers. The XMEGA core's 32 MHz speed renders menu animations and debounces 4x4 key matrices in real time, while the 4-channel DMA refreshes the LCD display RAM in the background without CPU intervention. The 256 KB Flash holds multilingual UI strings, bitmap fonts, and protocol stacks (Modbus RTU, ASCII), and the 16 KB SRAM buffers display double-buffering. The 64-pin TQFP provides 34 I/O lines for keypad scanning, status LEDs, and RS-485 transceivers.
Рекомендуется
IoT Sensor Hubs and Protocol Bridges
The ATXMEGA256A3U-AU bridges multiple sensor buses - I2C sensors, SPI peripherals, UART GPS modules, and analog inputs - into a unified USB or UART uplink to a host processor or cloud gateway. The rich peripheral mix (4 USART, 2 SPI, 2 TWI) allows simultaneous sensor aggregation without external muxes, and the 256 KB Flash holds TinyXML/JSON parsers, MQTT-SN, or proprietary sensor fusion code. The 4-channel DMA streams sensor data into SRAM while the CPU runs higher-level processing, and the event system lets sensor-ready interrupts trigger DMA without firmware polling. The wide 2.7-3.6V supply runs directly from a single Li-ion cell after regulation.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATXMEGA256A3U-AU — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATXMEGA256A3U-AUR | ATXMEGA192A3U-AU | ATXMEGA128A3U-AU | ATXMEGA64A3U-AU | ATXMEGA256A3U-ANR |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (14x14 mm) | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Flash | 256 KB | 256 KB | 192 KB (-25%) | 128 KB (-50%) | 64 KB (-75%) | 256 KB |
| SRAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| EEPROM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| USB 2.0 FS Device | Yes | Yes | Yes | Yes | Yes | Yes |
| Maximum Clock | 32 MHz (32 MIPS) | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Supply Voltage | 2.7-3.6 V | 2.7-3.6 V | 2.7-3.6 V | 2.7-3.6 V | 2.7-3.6 V | 2.7-3.6 V |
Ключевые отличия
- Largest Flash in the XMEGA A3U TQFP-64 family (против ATXMEGA192A3U-AU)
- Integrated USB 2.0 Full-Speed device controller (против ATXMEGA256A3-AU)
- 8/16-bit Harvard architecture with 32 MIPS throughput (против ATMEGA2560-16AU)
- 4-channel DMA + 8-channel event system (против ATMEGA328P-AUR)
Заметки по проектированию
Place a 100 nF ceramic decoupling capacitor as close as possible to each VCC/AVCC pin (pins 1, 20, 30, 40, 50, 60, 64), plus a single 10 uF bulk capacitor at the supply entry point. The XMEGA AU manual recommends separate analog and digital ground planes joined at a single point near the AVCC pin to avoid digital switching noise coupling into ADC measurements. For USB applications, route D+/D- (PF2/PF3) as a 90-ohm differential pair with a common-mode choke near the connector and ESD protection diode array (e.g., USBLC6-2SC6). Estimated decoupling budget: 7x 100 nF + 1x 10 uF = roughly 0.5 USD BOM cost.
The 64-pin TQFP package has a typical thermal resistance of approximately 50 C/W (theta_JA) for a standard 4-layer JEDEC test board. At maximum 32 MHz active current of approximately 14 mA from 3.3 V, the MCU dissipates roughly 46 mW of internal power, producing a junction-temperature rise of only 2-3 C above ambient. For closed-enclosure industrial designs, ensure ambient stays below 70 C to keep Tj below the 85 C industrial limit. In USB bus-powered designs where the MCU draws up to 100 mA from VBUS, internal dissipation rises to 330 mW and case temperature may rise 15-20 C above ambient - verify with a thermal probe in the final enclosure.
Route the PDI (PDI_DATA on pin 61, PDI_CLOCK on pin 62) signals to a dedicated 2x5 0.1-inch header or pogo-pin footprint for in-circuit programming and on-chip debug. The PDI clock can tolerate up to 10 MHz but typical AVR Studio programming uses 1-2 MHz; keep traces short (under 50 mm) and avoid running them parallel to switching signals like PWM outputs or the USB D+/D- pair. The RESET pin (pin 63) requires a 10 kohm pull-up to VCC; do not leave it floating during normal operation, or the MCU may intermittently enter programming mode. Place a 100 nF cap on RESET to ground for noise immunity.
Do not exceed VCC of 3.6 V - the ATXMEGA256A3U-AU is NOT 5 V tolerant on any pin, including the ADC inputs. The minimum VIH of 2.0 V at VCC > 2.7 V (per AVR1020 app note doc8416) means you cannot directly interface 5 V logic without a level shifter (e.g., TXS0108E or ADG3308). When migrating from the non-U ATXMEGA256A3 to the A3U variant, verify that PF2/PF3 are configured for USB only and not as GPIO - accidentally driving them as outputs will conflict with the USB peripheral. Estimated: level-shifters add 0.20-0.50 USD BOM cost and 50-150 mm2 PCB area.
When using the 12-bit ADC at the maximum 2 MSPS sample rate, add a small RC filter (typically 100 ohm + 1 nF) on each analog input to limit broadband noise and prevent fold-back from the sampling capacitor. For 50/60 Hz mains-frequency rejection, trigger ADC conversions from the event system synchronized to the 32.768 kHz TOSC, providing oversampling and decimation to achieve 16-bit effective resolution. The ADC reference can be the internal 1.0 V bandgap (drift ~5 mV/C), the internal AVCC scaled reference, or an external VREF pin - choose the external reference for absolute accuracy better than 1% across temperature.
Информация о соответствии
RoHS compliant per Microchip product page. Industrial temperature grade (-40C to +85C). Not AEC-Q100 qualified - this part targets industrial/consumer rather than automotive. Halogen-free status not explicitly documented in verified data.
